onsemi

LM239DR2G - Quad 36V Open-Collector Comparator | onsemi

MPN: LM239DR2G ✓ सक्रिय
3 V to 36 V Vdss 250 nA typical Id 14-SOIC Package
न्यूनतम ऑर्डर मात्रा: 1 |

LM239DR2G अवलोकन

The onsemi LM239DR2G is a single-supply quad comparator with four independent differential input channels, a 3 V to 36 V supply range, and open-collector outputs. The device provides a typical input offset voltage of 5 mV, typical input bias current of 250 nA, and typical propagation delay of 1.3 microseconds in a 14-pin SOIC package rated for -25 C to +85 C operation.

A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM239 belongs to the comparator hierarchy, alongside open-collector and CMOS-compatible interface circuits used for level detection, low-level sensing, and memory applications. Four integrated channels allow one package to perform threshold detection, window monitoring, overvoltage detection, or relay-driving functions.

The open-collector outputs can sink current from multiple compatible loads while the output transistor remains off, allowing the designer to select an external pull-up resistor and establish the output logic voltage independently of the comparator supply. This architecture is compatible with TTL, CMOS, and MOS loads, while the 36 V maximum supply rating supports higher-voltage industrial and consumer systems. The typical 1.3 microsecond propagation delay is suitable for general-purpose signal comparison rather than high-speed timing applications.

Each channel contains a differential input stage and a discrete output stage. The two inputs of a channel should be connected so that the non-inverting input receives the signal to be detected and the inverting input receives the reference threshold, or vice versa when an inverted output is required. With an open-collector output, the output state is not valid until the external pull-up resistor establishes the high level, so timing calculations must include the pull-up network and any attached load capacitance.

Typical applications include industrial control and automation, battery-powered monitoring, power-supply fault detection, sensor threshold conditioning, and memory or system supervision. The quad channel count is especially useful when a board must monitor several rails or compare multiple sensor signals against independently generated references. The wide supply range also permits operation from regulated 5 V, 12 V, and 24 V systems within the stated device ratings.

For PCB design, place the pull-up resistor close to each open-collector output and route the comparator inputs away from switching nodes and high-current switching paths. Input bias current of 250 nA typical and 5 mV typical offset make resistor-divider design sensitive to source impedance. Verify that the selected pull-up network does not exceed the output sink-current capability and that the SOIC footprint matches the chosen temperature and packing variant.

This page combines manufacturer and distributor component information with a pin-level application guide, drop-in replacement analysis, and practical design notes. It also identifies which electrical characteristics are confirmed for the LM239DR2G and where a design engineer must consult the full manufacturer datasheet before releasing a production schematic.

के लिए ड्रॉप-इन विकल्प LM239DR2G — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM239DR2G (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Comparator Type, Output Type, Input Offset Voltage, Supply Configuration, Package.

onsemi
Comparator Type: General-purpose differential comparator
Output Type: Open collector with CMOS, open-collector, and TTL compatibility
Supply Configuration: Single supply or dual supply
इसके साथ तुलना करें LM239DR2G →
Texas Instruments
Comparator Type: Quad precision differential voltage comparator
Input Offset Voltage: 2 mV maximum for LM239A family variants; LM239DR-specific value not supplied
Package: 14-pin SOIC
इसके साथ तुलना करें LM239DR2G →
onsemi
Comparator Type: 4-channel differential comparator
Input Offset Voltage: ±1 mV typical
Supply Configuration: Single supply or split supply
इसके साथ तुलना करें LM239DR2G →
onsemi
Comparator Type: General Purpose
Output Type: Open Collector
Supply Configuration: Single
इसके साथ तुलना करें LM239DR2G →

LM239DR2

✅ ड्रॉप-इन
📦 14-SOIC
Same onsemi LM239 family and 14-SOIC footprint; ordering-code ratings must be checked, with no verified parametric difference quantified in the available listing

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LM239DR

✅ ड्रॉप-इन
Texas Instruments
📦 14-SOIC
Quad precision differential voltage comparator · 4 independent channels · ±15 V or 30 V · Open-collector · 25 nA typical · ±5.0 nA typical · 2 mV maximum for LM239A family variants; LM239DR-specific value not supplied · 1.3 µs typical

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM239ADR

✅ ड्रॉप-इन
📦 14-SOIC
Texas Instruments 14-SOIC quad open-collector variant; ordering code differs and worst-case limits must be compared with the onsemi specification

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

LM339DR2G

✅ ड्रॉप-इन
onsemi
📦 14-SOIC
General Purpose · 4 channels · 3 V to 36 V · Single · 1.3 us · 25 nA typical · ±5 nA typical · 1 mA typical

कीमत के लिए संपर्क करें

डेटाशीट देखें →

LM239DR2G Maximum Ratings और Electrical Characteristics

Comparator Type Quad differential comparator
Number of Channels 4 channels
Supply Voltage Range 3 V to 36 V
आउटपुट प्रकार Open-collector
Logic Compatibility CMOS and TTL compatible
Input Offset Voltage 5 mV typical
Input Bias Current 250 nA typical
Propagation Delay 1.3 microseconds typical
ऑपरेटिंग तापमान रेंज -25 C to +85 C
पैकेज 14-SOIC
माउंटिंग प्रकार Surface mount
RoHS स्थिति Compliant
Automotive Qualification Not AEC-Q100 qualified
Single-Supply Operation Yes
Output Pull-Up Resistor External, application dependent

LM239DR2G पिन कॉन्फ़िगरेशन

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
पिन 1 OUT1 — Open-collector output of comparator channel 1
पिन 2 IN1- — Inverting input of comparator channel 1
पिन 3 IN1+ — Non-inverting input of comparator channel 1
पिन 4 GND — Ground connection
पिन 5 IN2+ — Non-inverting input of comparator channel 2
पिन 6 IN2- — Inverting input of comparator channel 2
पिन 7 OUT2 — Open-collector output of comparator channel 2
पिन 8 OUT3 — Open-collector output of comparator channel 3
पिन 9 IN3+ — Non-inverting input of comparator channel 3
पिन 10 IN3- — Inverting input of comparator channel 3
पिन 11 GND — Ground connection
पिन 12 IN4+ — Non-inverting input of comparator channel 4
पिन 13 IN4- — Inverting input of comparator channel 4
पिन 14 OUT4 — Open-collector output of comparator channel 4

सामान्य अनुप्रयोग

LM239DR2G के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Control and Automation, Battery and Power-Supply Monitoring, Sensor Threshold Conditioning, Overvoltage and Fault Protection, Relay and MOSFET Driver Interface, Automotive and Consumer Low-Level Sensing.

🏭

Industrial Control and Automation

The LM239DR2G fits 12 V or 24 V industrial control boards that compare sensor signals, command levels, or safety thresholds. Its four channels reduce component count when several independent decisions are required, while the 3 V to 36 V supply range supports the 24 V rail commonly found in factory equipment. Each open-collector output can drive a PLC input, relay-driver transistor, or alarm indicator through an external pull-up. The 5 mV typical offset and 250 nA typical bias current are manageable when the input divider impedance is kept moderate, and the -25 C to +85 C rating covers many factory environments.

⚡

Battery and Power-Supply Monitoring

The LM239DR2G is useful for multi-rail battery systems that must detect undervoltage, overvoltage, or an out-of-range battery condition. Four comparison channels can monitor different thresholds without requiring four separate packages, and the open-collector outputs allow alarm signals to be pulled up to a low-power logic rail. The 36 V maximum supply rating supports higher-voltage monitoring architectures, although the input common-mode limits must be respected. With a typical propagation delay of 1.3 microseconds, the device is well suited to continuous threshold supervision rather than high-frequency event detection.

🧩

Sensor Threshold Conditioning

The LM239DR2G converts a slowly varying sensor voltage into a clean digital threshold event. The non-inverting input can receive the sensor signal while the inverting input receives a resistor-divider reference, allowing the comparison point to be set with standard 1 percent resistors. Because the typical input bias current is 250 nA, divider values should not be unnecessarily large. The open-collector output and its external pull-up integrate directly with CMOS or TTL logic, making the part suitable for temperature, level, and pressure sensing boards where the output must reliably represent whether the measured value is above or below a setpoint.

🖥️

Overvoltage and Fault Protection

The LM239DR2G can supervise several protected rails and generate open-collector fault indications when a monitored voltage crosses its reference. Its four channels provide independent comparisons in one 14-SOIC package, reducing board area compared with discrete single comparators. The 3 V to 36 V supply range accommodates both low-voltage logic and higher industrial rails, and the CMOS and TTL-compatible outputs simplify connection to a system controller. Design the reference divider for temperature stability, confirm that the monitored signal remains inside the common-mode range, and account for the 1.3 microsecond typical delay when responding to rapidly changing faults.

🔧

Relay and MOSFET Driver Interface

The LM239DR2G can control a relay-driver or power-MOSFET gate when the application needs a logic-controlled, isolated pull-down path rather than a push-pull logic output. The open-collector transistor sinks current from the gate pull-up or relay-driver base, and a flyback diode is required across an inductive relay coil. Four channels permit multiple discrete load controls on one board. The external pull-up resistor must be selected so that its maximum sink demand remains within the comparator output rating, while the -25 C to +85 C operating range and 36 V supply limit define the usable environmental envelope.

🚗

Automotive and Consumer Low-Level Sensing

The LM239DR2G supports general-purpose low-level sensing in consumer and automotive-adjacent equipment, including battery indicators, system supervisors, and simple control interlocks. Four channels allow a compact board to evaluate several switch, sensor, or supply conditions. The open-collector outputs are compatible with CMOS and TTL and can be pulled up to the local logic rail, while the 3 V to 36 V supply range covers 5 V, 12 V, and 24 V environments within the stated rating. The device is not AEC-Q100 qualified, so an automotive design should use an appropriately qualified comparator when the AEC-Q100 grade is required.

What is the LM239DR2G and what are its main specifications?
The LM239DR2G is a single-supply quad differential comparator from onsemi. According to the onsemi LM239 datasheet and product information, it contains four independently operating channels, accepts a 3 V to 36 V supply, provides open-collector outputs compatible with CMOS and TTL, and offers a typical propagation delay of 1.3 microseconds. It is packaged in a 14-pin SOIC and specified for -25 C to +85 C operation.
Where can I download the LM239DR2G datasheet PDF?
The LM239DR2G datasheet can be obtained through the onsemi LM239 product page and the manufacturer PDF link for the family. The datasheet identifies the device as a single-supply quad comparator and provides the authoritative pin description, electrical characteristics, and application information. Use the onsemi document for production design decisions rather than relying on distributor summary pages or third-party datasheet mirrors.
Where can I find the LM239DR2G pinout?
The LM239DR2G pinout is shown in the pin-description table of the onsemi LM239 datasheet. This 14-pin SOIC contains four open-collector outputs, four inverting inputs, four non-inverting inputs, and two ground pins. Use the datasheet pin table when assigning PCB nets because the order of output, input, and ground connections must match the 14-lead SOIC numbering exactly.
What can replace the LM239DR2G as a drop-in part?
The LM239DR2 is the closest same-manufacturer option identified for the LM239DR2G, while LM239DR, LM239ADR, and LM339DR2G appear in cross-reference listings for the same comparator family. Each candidate must be checked for identical 14-pin SOIC pinout, open-collector output stage, supply rating, input common-mode range, output sink current, and temperature grade before it is treated as a drop-in replacement.
Is the Texas Instruments LM239DR a drop-in replacement for the LM239DR2G?
The LM239DR is a strong candidate because both devices are quad open-collector comparators offered in a 14-pin SOIC package. According to the TI LM239 product page, the LM239 B-version is a drop-in replacement for the LM239, LM339, and LM2901 families, with outputs compatible with TTL, MOS, and CMOS. Final acceptance still requires comparing the specific suffix ratings and worst-case electrical limits.
What is the difference between LM239DR2G and LM239DR?
The principal difference is manufacturer and ordering configuration: the LM239DR2G is the onsemi version, while LM239DR is the Texas Instruments version. Both are described as quad, open-collector, 14-SOIC general-purpose comparators. A board-level substitution should compare supply range, input offset, common-mode range, propagation delay, output sink current, temperature grade, and the exact pinout rather than relying on the family description alone.
When should I choose the LM239DR2G instead of the LM239DR?
Choose the LM239DR2G when your qualified bill of materials specifically uses the onsemi device, existing inventory is already designed around that ordering code, or the onsemi LM239 documentation is the approved technical reference for the product. Choose the LM239DR when a Texas Instruments second source is preferred and its suffix-specific ratings satisfy the design. Both use the same 14-pin SOIC comparison format, but production equivalence must be confirmed against the applicable datasheets.
Is the LM239DR2G suitable for 24 V industrial control systems?
The LM239DR2G is suitable for 24 V industrial applications within its stated ratings because its supply range extends to 36 V and it is specified over -25 C to +85 C. Its open-collector output allows an external pull-up to the system logic voltage. Verify transient margins, input common-mode limits, and output sink-current requirements for the actual 24 V rail and wiring environment.
How do I use the open-collector output of the LM239DR2G?
Connect an external pull-up resistor from each LM239DR2G output to the desired positive logic supply. When the output transistor turns on, the node is pulled toward ground; when it turns off, the resistor raises the node to the logic rail. The resistor should be small enough to deliver the required sink current during the low state and large enough to limit the low-to-high transition time with the connected load capacitance.
What are the key LM239DR2G specifications engineers should know?
The principal LM239DR2G specifications are a 3 V to 36 V supply range, four differential comparator channels, open-collector CMOS and TTL-compatible outputs, 5 mV typical input offset voltage, 250 nA typical input bias current, and 1.3 microseconds typical propagation delay. The device uses a 14-pin SOIC package and has an operating-temperature range of -25 C to +85 C. These figures make it a general-purpose choice for level detection and low-level sensing.
How much pull-up resistance should I use with the LM239DR2G?
The correct pull-up value depends on the output sink-current limit, the required low-state voltage, the logic supply voltage, and the load capacitance, all of which must be taken from the manufacturer data. Start by confirming the maximum sink current at the intended output voltage, then select a resistor that stays inside that limit while producing an acceptable rising edge at the receiver. A value near 10 kilohms is common in digital logic interfaces but is not a universal substitute for the device ratings.
Can the LM239DR2G drive a relay or MOSFET gate?
The LM239DR2G can serve as the control element in relay-driver or MOSFET-gate circuits because its output is an open-collector transistor rather than a push-pull CMOS output. Add a flyback diode for an inductive relay load and ensure the comparator output transistor can sink the selected pull-up current. The absence of an active pull-up means the load or gate must be referenced to a suitable positive supply through an external resistor.
Is there an onsemi equivalent for the LM239DR2G?
The onsemi LM239DR2 is the closest same-manufacturer candidate found for the LM239DR2G, and it appears in the same 14-SOIC comparator listing. Confirm the device description, packing suffix, temperature grade, and electrical limits before substitution. The LM239DR2G and LM239DR2 are closely related orderable versions of the LM239 family, but a purchasing or qualification team should approve any change using the exact manufacturer documentation.
How do I prevent false comparator triggering in the LM239DR2G?
Prevent false triggering by keeping the two inputs of each channel close in voltage during normal operation, routing them away from switching nodes, and placing input-referenced components where their resistance and thermal drift do not create excessive offset. Because the typical input bias current is 250 nA, high-impedance dividers can shift the apparent threshold. Slow input signals also require care around the 1.3 microseconds typical propagation delay and output pull-up network.
Where can I buy LM239DR2G online and what is its lead time?
The LM239DR2G is available through authorized component distributors and XAIPART sourcing channels. Use the Request a Quote form on this page for current commercial availability, unit pricing, minimum order quantity, and a lead time tied to the requested quantity. The distributor listing confirms the onsemi part and 14-SOIC configuration, but a firm manufacturing schedule should be confirmed when the quote is accepted.

के लिए इंजीनियरिंग संदर्भ डेटा LM239DR2G — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the LM239DR2G when a design needs four general-purpose threshold comparisons, a supply range extending to 36 V, and open-collector outputs that can interface with CMOS or TTL logic. The onsemi ordering code is appropriate when the LM239DR2G is already present in the approved bill of materials or when onsemi documentation is the controlling technical reference. Consider the LM239DR2 for a same-manufacturer second source after checking its suffix-specific ratings. The Texas Instruments LM239DR and LM239ADR are second-source options for a 14-SOIC quad-comparator footprint, but the exact pinout, worst-case offset, bias current, common-mode range, output sink current, and temperature grade must be compared before substitution. The LM339DR2G is a related family option rather than an unconditional equivalent, so use it only after reviewing the TI comparison and electrical data. For applications requiring AEC-Q100 qualification, select an appropriately qualified automotive comparator instead of assuming this industrial-temperature part meets that requirement.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद LM239DR2 LM239DR LM239ADR LM339DR2G
Manufacturer onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Package 14-SOIC 14-SOIC - same 14-SOIC - same 14-SOIC - same 14-SOIC - same family footprint
Number of Channels 4 4 4 4 4
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector

मुख्य विशेषताएँ

  • Four comparison channels in a single 14-SOIC package (बनामLM2902N/PB)
  • Wide single-supply operating range (बनामLM239ADR)
  • Open-collector interface with CMOS and TTL compatibility (बनामLM339DR2G)
  • Input bias and offset performance for general-purpose sensing (बनामLM239ADR)

डिज़ाइन नोट्स

Do not treat the open-collector output as a push-pull CMOS output. Every output requires an external pull-up resistor, and its high-state voltage is determined by that resistor and the chosen logic rail. Check the maximum sink current at the required low-level voltage before reducing resistance. If the output drives a long cable or high-capacitance node, evaluate the rising edge produced by the pull-up network rather than assuming the 1.3 microseconds typical propagation delay is the complete output transition time.

Keep input-divider impedances low enough that the typical 250 nA input bias current does not create a meaningful threshold shift. Input offset voltage is typically 5 mV, so resistor tolerance, temperature drift, and nearby noise sources can become significant errors in a precision monitor. Place reference-divider resistors close to the relevant input pins, bypass noisy analog sources where practical, and route the inputs away from switching-node copper and high-current return paths.

Use a standard 14-pin SOIC land pattern and confirm the pin-1 orientation against the package drawing. Route each open-collector output to its pull-up resistor with a short trace, and keep the output away from sensitive comparator inputs. Provide a low-impedance ground path for both ground pins. In a mixed-signal board, place the comparator near the protected or monitored circuit, use a continuous ground reference, and separate the pull-up return current from analog-reference currents where practical.

अनुपालन जानकारी

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The LCSC product listing identifies the LM239DR2G as RoHS compliant. No specific REACH, halogen-free, conflict-minerals, or AEC-Q100 declaration was identified for this ordering code.

डेटा सत्यापन तिथि: 2026-11-15 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

LM239DR2G LM239DR2G datasheet LM239DR2G datasheet pdf LM239DR2G pinout onsemi LM239DR2G LM239DR2G equivalent LM239DR2G replacement LM239DR2G vs LM239DR LM239DR2G open collector output LM239DR2G 14-SOIC footprint LM239DR2G power supply monitoring LM239DR2G price LM239DR2G stock LM239DR2G cross reference

संबंधित कंपोनेंट्स और शब्द

onsemi LM239DR2G LM239DR2 LM239DR LM239ADR LM339DR2G quad differential comparator comparator analog integrated circuit open-collector output external pull-up resistor single-supply operation input offset voltage input bias current propagation delay common-mode voltage range level detection low-level sensing power-supply monitoring industrial control battery monitoring relay driver 14-SOIC package SOIC package family surface-mount package RoHS AEC-Q100 CMOS compatible TTL compatible
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें