LM239DR2G - Quad 36V Open-Collector Comparator | onsemi
MPN: LM239DR2G ✓ AktifLM239DR2G Ringkasan
A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state when the difference between them crosses a defined threshold. The LM239 belongs to the comparator hierarchy, alongside open-collector and CMOS-compatible interface circuits used for level detection, low-level sensing, and memory applications. Four integrated channels allow one package to perform threshold detection, window monitoring, overvoltage detection, or relay-driving functions.
The open-collector outputs can sink current from multiple compatible loads while the output transistor remains off, allowing the designer to select an external pull-up resistor and establish the output logic voltage independently of the comparator supply. This architecture is compatible with TTL, CMOS, and MOS loads, while the 36 V maximum supply rating supports higher-voltage industrial and consumer systems. The typical 1.3 microsecond propagation delay is suitable for general-purpose signal comparison rather than high-speed timing applications.
Each channel contains a differential input stage and a discrete output stage. The two inputs of a channel should be connected so that the non-inverting input receives the signal to be detected and the inverting input receives the reference threshold, or vice versa when an inverted output is required. With an open-collector output, the output state is not valid until the external pull-up resistor establishes the high level, so timing calculations must include the pull-up network and any attached load capacitance.
Typical applications include industrial control and automation, battery-powered monitoring, power-supply fault detection, sensor threshold conditioning, and memory or system supervision. The quad channel count is especially useful when a board must monitor several rails or compare multiple sensor signals against independently generated references. The wide supply range also permits operation from regulated 5 V, 12 V, and 24 V systems within the stated device ratings.
For PCB design, place the pull-up resistor close to each open-collector output and route the comparator inputs away from switching nodes and high-current switching paths. Input bias current of 250 nA typical and 5 mV typical offset make resistor-divider design sensitive to source impedance. Verify that the selected pull-up network does not exceed the output sink-current capability and that the SOIC footprint matches the chosen temperature and packing variant.
This page combines manufacturer and distributor component information with a pin-level application guide, drop-in replacement analysis, and practical design notes. It also identifies which electrical characteristics are confirmed for the LM239DR2G and where a design engineer must consult the full manufacturer datasheet before releasing a production schematic.
Alternatif penggantian untuk LM239DR2G — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian LM239DR2G (sama faktor bentuk dan footprint) — berbeda di dalam Comparator Type, Output Type, Input Offset Voltage, Supply Configuration, Package.
LM239DR2
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LM239DR
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM239ADR
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
LM339DR2G
✅ Drop-InKontak untuk harga
Lihat Datasheet →LM239DR2G Rating Maksimal & Karakteristik Listrik
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 3 V to 36 V |
| Tipe Output | Open-collector |
| Logic Compatibility | CMOS and TTL compatible |
| Input Offset Voltage | 5 mV typical |
| Input Bias Current | 250 nA typical |
| Propagation Delay | 1.3 microseconds typical |
| Rentang Suhu Kerja | -25 C to +85 C |
| Paket | 14-SOIC |
| Tipe Mounting | Surface mount |
| Status RoHS | Compliant |
| Automotive Qualification | Not AEC-Q100 qualified |
| Single-Supply Operation | Yes |
| Output Pull-Up Resistor | External, application dependent |
Konfigurasi Pin LM239DR2G
| Pin produk 1 | OUT1 — Open-collector output of comparator channel 1 |
| Pin produk 2 | IN1- — Inverting input of comparator channel 1 |
| Pin produk 3 | IN1+ — Non-inverting input of comparator channel 1 |
| Pin produk 4 | GND — Ground connection |
| Pin produk 5 | IN2+ — Non-inverting input of comparator channel 2 |
| Pin produk 6 | IN2- — Inverting input of comparator channel 2 |
| Pin produk 7 | OUT2 — Open-collector output of comparator channel 2 |
| Pin produk 8 | OUT3 — Open-collector output of comparator channel 3 |
| Pin produk 9 | IN3+ — Non-inverting input of comparator channel 3 |
| Pin produk 10 | IN3- — Inverting input of comparator channel 3 |
| Pin produk 11 | GND — Ground connection |
| Pin produk 12 | IN4+ — Non-inverting input of comparator channel 4 |
| Pin produk 13 | IN4- — Inverting input of comparator channel 4 |
| Pin produk 14 | OUT4 — Open-collector output of comparator channel 4 |
Aplikasi Umum
LM239DR2G cocok untuk 6 aplikasis: Industrial Control and Automation, Battery and Power-Supply Monitoring, Sensor Threshold Conditioning, Overvoltage and Fault Protection, Relay and MOSFET Driver Interface, Automotive and Consumer Low-Level Sensing.
Industrial Control and Automation
The LM239DR2G fits 12 V or 24 V industrial control boards that compare sensor signals, command levels, or safety thresholds. Its four channels reduce component count when several independent decisions are required, while the 3 V to 36 V supply range supports the 24 V rail commonly found in factory equipment. Each open-collector output can drive a PLC input, relay-driver transistor, or alarm indicator through an external pull-up. The 5 mV typical offset and 250 nA typical bias current are manageable when the input divider impedance is kept moderate, and the -25 C to +85 C rating covers many factory environments.
Direkomendasikan
Battery and Power-Supply Monitoring
The LM239DR2G is useful for multi-rail battery systems that must detect undervoltage, overvoltage, or an out-of-range battery condition. Four comparison channels can monitor different thresholds without requiring four separate packages, and the open-collector outputs allow alarm signals to be pulled up to a low-power logic rail. The 36 V maximum supply rating supports higher-voltage monitoring architectures, although the input common-mode limits must be respected. With a typical propagation delay of 1.3 microseconds, the device is well suited to continuous threshold supervision rather than high-frequency event detection.
Direkomendasikan
Sensor Threshold Conditioning
The LM239DR2G converts a slowly varying sensor voltage into a clean digital threshold event. The non-inverting input can receive the sensor signal while the inverting input receives a resistor-divider reference, allowing the comparison point to be set with standard 1 percent resistors. Because the typical input bias current is 250 nA, divider values should not be unnecessarily large. The open-collector output and its external pull-up integrate directly with CMOS or TTL logic, making the part suitable for temperature, level, and pressure sensing boards where the output must reliably represent whether the measured value is above or below a setpoint.
Direkomendasikan
Overvoltage and Fault Protection
The LM239DR2G can supervise several protected rails and generate open-collector fault indications when a monitored voltage crosses its reference. Its four channels provide independent comparisons in one 14-SOIC package, reducing board area compared with discrete single comparators. The 3 V to 36 V supply range accommodates both low-voltage logic and higher industrial rails, and the CMOS and TTL-compatible outputs simplify connection to a system controller. Design the reference divider for temperature stability, confirm that the monitored signal remains inside the common-mode range, and account for the 1.3 microsecond typical delay when responding to rapidly changing faults.
Direkomendasikan
Relay and MOSFET Driver Interface
The LM239DR2G can control a relay-driver or power-MOSFET gate when the application needs a logic-controlled, isolated pull-down path rather than a push-pull logic output. The open-collector transistor sinks current from the gate pull-up or relay-driver base, and a flyback diode is required across an inductive relay coil. Four channels permit multiple discrete load controls on one board. The external pull-up resistor must be selected so that its maximum sink demand remains within the comparator output rating, while the -25 C to +85 C operating range and 36 V supply limit define the usable environmental envelope.
Direkomendasikan
Automotive and Consumer Low-Level Sensing
The LM239DR2G supports general-purpose low-level sensing in consumer and automotive-adjacent equipment, including battery indicators, system supervisors, and simple control interlocks. Four channels allow a compact board to evaluate several switch, sensor, or supply conditions. The open-collector outputs are compatible with CMOS and TTL and can be pulled up to the local logic rail, while the 3 V to 36 V supply range covers 5 V, 12 V, and 24 V environments within the stated rating. The device is not AEC-Q100 qualified, so an automotive design should use an appropriately qualified comparator when the AEC-Q100 grade is required.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk LM239DR2G — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | LM239DR2 | LM239DR | LM239ADR | LM339DR2G |
|---|---|---|---|---|---|
| Manufacturer | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same | 14-SOIC - same family footprint |
| Number of Channels | 4 | 4 | 4 | 4 | 4 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Diferensiator Kunci
- Four comparison channels in a single 14-SOIC package (vsLM2902N/PB)
- Wide single-supply operating range (vsLM239ADR)
- Open-collector interface with CMOS and TTL compatibility (vsLM339DR2G)
- Input bias and offset performance for general-purpose sensing (vsLM239ADR)
Catatan Desain
Do not treat the open-collector output as a push-pull CMOS output. Every output requires an external pull-up resistor, and its high-state voltage is determined by that resistor and the chosen logic rail. Check the maximum sink current at the required low-level voltage before reducing resistance. If the output drives a long cable or high-capacitance node, evaluate the rising edge produced by the pull-up network rather than assuming the 1.3 microseconds typical propagation delay is the complete output transition time.
Keep input-divider impedances low enough that the typical 250 nA input bias current does not create a meaningful threshold shift. Input offset voltage is typically 5 mV, so resistor tolerance, temperature drift, and nearby noise sources can become significant errors in a precision monitor. Place reference-divider resistors close to the relevant input pins, bypass noisy analog sources where practical, and route the inputs away from switching-node copper and high-current return paths.
Use a standard 14-pin SOIC land pattern and confirm the pin-1 orientation against the package drawing. Route each open-collector output to its pull-up resistor with a short trace, and keep the output away from sensitive comparator inputs. Provide a low-impedance ground path for both ground pins. In a mixed-signal board, place the comparator near the protected or monitored circuit, use a continuous ground reference, and separate the pull-up return current from analog-reference currents where practical.
Informasi Konformitas
The LCSC product listing identifies the LM239DR2G as RoHS compliant. No specific REACH, halogen-free, conflict-minerals, or AEC-Q100 declaration was identified for this ordering code.