LM2902WYDT - 1.3MHz Quad Op Amp | STMicroelectronics
MPN: LM2902WYDT ✓ सक्रियLM2902WYDT अवलोकन
A quad operational amplifier combines four amplifiers in one package, reducing component count and simplifying board layout. In the broader electronics hierarchy, an operational amplifier is an analog amplifier IC used within signal chains and measurement systems. Each LM2902WYDT amplifier can perform common functions such as voltage buffering, amplification, filtering, comparison, and differential input conditioning, depending on the feedback network and surrounding components.
The principal characteristics include 1.3 MHz gain-bandwidth performance, 100 dB open-loop gain, 375 uA supply current, 20 nA input offset current, 2 nA input bias current, and an 800 V input differential voltage rating. Internal frequency compensation allows the amplifiers to operate as stable unity-gain buffers without external compensation components. Push-pull outputs support bidirectional output current required by many closed-loop amplifier configurations.
The device uses four independent amplifiers, so one package can implement several analog functions on the same board. Its low-power operating characteristics are useful when multiple amplifier channels are required, while the 1.3 MHz bandwidth is suitable for general-purpose industrial signal paths rather than precision high-frequency instrumentation. The 800 V maximum differential input voltage provides substantial headroom for signal transients, although correct input protection and common-mode analysis remain necessary in each application.
Typical uses include industrial sensor conditioning, transducer amplification, audio preamplifier stages, active filters, differential amplifiers, and general instrumentation. Four independent channels can reduce the number of packages required in multi-channel analog boards. Each amplifier uses the same electrical architecture, allowing designers to assign separate signal paths while sharing common supply and decoupling arrangements.
For PCB implementation, place the power-bypass capacitor close to the supply pin and route feedback connections to minimize parasitic pickup. Keep sensitive input nodes away from high-current output and supply paths. Decoupling requirements, stable operating points, input common-mode limits, and output-swing limits must be checked against the manufacturer datasheet for the selected supply voltage and load.
This product record combines the manufacturer functional description with distributor part identification, package information, key electrical ratings, sourcing access, drop-in alternatives, and practical application guidance. It helps engineers move from datasheet review to PCB-level implementation while keeping the LM2902WYDT's four-channel architecture and electrical boundaries central to component selection.
के लिए ड्रॉप-इन विकल्प LM2902WYDT — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2902WYDT (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Input Bias Current, Package, Gain-Bandwidth Product, Input Offset Current.
LM2902AWYDT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902HYDT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM2902KVQDRQ1
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902WDT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902WYPT
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2902WYDT Maximum Ratings और Electrical Characteristics
| Number of Amplifiers | 4 circuits |
| Amplifier Type | Standard general-purpose operational amplifier |
| Gain-Bandwidth Product | 1.3 MHz |
| Open-Loop Gain | 100 dB |
| सप्लाई करंट | 375 uA |
| Input Offset Current | 20 nA |
| Input Bias Current | 2 nA |
| Maximum Differential Input Voltage | 800 V |
| आउटपुट प्रकार | Push-pull |
| Frequency Compensation | Internal |
| Number of Independent Amplifiers | 4 independent amplifiers |
| पैकेज | 14-SO |
| माउंटिंग प्रकार | Surface mount |
| RoHS स्थिति | RoHS compliant |
LM2902WYDT पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Amplifier 1 output |
| पिन 2 | IN1- — Amplifier 1 inverting input |
| पिन 3 | IN1+ — Amplifier 1 non-inverting input |
| पिन 4 | VCC+ — Positive supply voltage |
| पिन 5 | IN2+ — Amplifier 2 non-inverting input |
| पिन 6 | IN2- — Amplifier 2 inverting input |
| पिन 7 | OUT2 — Amplifier 2 output |
| पिन 8 | OUT3 — Amplifier 3 output |
| पिन 9 | IN3- — Amplifier 3 inverting input |
| पिन 10 | IN3+ — Amplifier 3 non-inverting input |
| पिन 11 | VCC- — Negative supply voltage |
| पिन 12 | IN4+ — Amplifier 4 non-inverting input |
| पिन 13 | IN4- — Amplifier 4 inverting input |
| पिन 14 | OUT4 — Amplifier 4 output |
सामान्य अनुप्रयोग
LM2902WYDT के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Audio Preamplifier and Mixer Stages, Active Filters and Equalization, Transducer and Bridge Interface Circuits, Data Acquisition and Instrumentation, Control-System Amplifier and Comparator Network.
Industrial Sensor Signal Conditioning
The LM2902WYDT is well suited to conditioning low-level signals from industrial sensors because it provides four independent, internally compensated amplifiers in one 14-SO package. The 2 nA input bias current and 20 nA input offset current are useful when driving relatively high source impedances, while 100 dB open-loop gain supports accurate closed-loop amplification. Designers can combine the channels for a noninverting front end, an inverting stage, a difference amplifier, and an active filter. The 1.3 MHz gain-bandwidth product is adequate for many process-control and factory-sensing signals, although the selected resistor and capacitor values must keep closed-loop bandwidth below the amplifier's capabilities.
अनुशंसित
Audio Preamplifier and Mixer Stages
The four push-pull amplifier channels in the LM2902WYDT can implement separate preamplifier, summing, buffering, or active-filter stages in a general-purpose audio board. Push-pull outputs allow each closed-loop stage to source and sink output current, which is important when driving the next stage rather than operating only as a passive-biased output. The 1.3 MHz gain-bandwidth product covers a broad range of audio-band signal paths, and 100 dB open-loop gain can support high closed-loop gain when operating within the stable bandwidth. For low-noise audio designs, verify input-voltage and input-current noise, output distortion, supply ripple sensitivity, and output-swing limits against the manufacturer datasheet.
अनुशंसित
Active Filters and Equalization
A single LM2902WYDT package can implement several stages of active low-pass, high-pass, or band-pass filtering because it contains four independent, internally compensated amplifiers. Internal compensation removes the need for an external frequency-compensation capacitor in unity-gain voltage-follower service. The 1.3 MHz gain-bandwidth product gives ample bandwidth for many audio, control, and measurement filters, while 100 dB open-loop gain supports high-Q filter designs when component tolerances and stability are properly controlled. Use conventional resistor-capacitor networks around each channel, keep the feedback loop short, and verify phase margin and expected gain error with the selected topology. The same package can also combine filtering with an output buffer.
अनुशंसित
Transducer and Bridge Interface Circuits
The LM2902WYDT can form the analog front end for resistive, strain-gauge, or bridge-based transducers where four channels support excitation buffering, differential sensing, amplification, and output filtering. Its 2 nA input bias current helps reduce loading on high-impedance sensor networks, while the 20 nA input offset-current rating provides a basis for evaluating output-referred error in sensitive stages. Differential amplifier and instrumentation-style arrangements require close attention to resistor-ratio matching, common-mode input range, and output swing. Because the input-stage characteristics are shared across the four channels, matched network layout and thermal conditions help preserve channel-to-channel consistency.
अनुशंसित
Data Acquisition and Instrumentation
The LM2902WYDT can provide several gain and buffering functions around an acquisition circuit without requiring four separate amplifier packages. A practical arrangement may use one channel to amplify the sensor output, one as a unity-gain buffer, another for offset correction, and a fourth for driving the analog-to-digital converter input. The 1.3 MHz gain-bandwidth product is suitable for many moderate-speed acquisition channels, while the 100 dB open-loop gain supports accurate closed-loop performance at lower signal frequencies. Check the selected ADC's input range against the amplifier's output-swing capability, and confirm that the operating supply and common-mode range satisfy the sensor's signal excursion.
अनुशंसित
Control-System Amplifier and Comparator Network
The LM2902WYDT supports compact analog control systems requiring amplification, comparison, filtering, and output buffering within one package. Four independent channels can reduce board area in feedback-control loops, actuator-driver interfaces, and threshold-detection circuits. The internal frequency compensation and push-pull output stage make the amplifiers convenient for closed-loop voltage-follower and inverting configurations, while the 1.3 MHz bandwidth covers many slow industrial control loops. Comparator operation still requires attention to output saturation recovery, input offset, noise around the threshold, and settling time. Verify that the control signal remains within the specified common-mode range and that the load current stays within the output-stage limits.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM2902WYDT — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM2902AWYDT | LM2902HYDT | LM2902KVQDR | LM2902WDT | LM2902WYPT |
|---|---|---|---|---|---|---|
| Package | 14-SO | 14-SO | 14-SO | 14-SOIC | 14-SO | 14-SO |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
मुख्य विशेषताएँ
- Four independent channels in one 14-SO package (बनामLM324KAPWR)
- Push-pull output architecture (बनामLM2902AWYDT)
- General-purpose signal bandwidth (बनामLM2902HYDT)
डिज़ाइन नोट्स
Place the supply-bypass capacitor immediately between the VCC+ and VCC- pins, with short, low-inductance traces and a solid ground return. Keep each feedback loop compact and route it away from adjacent input and output nets. Because the package contains four amplifiers, maintain consistent grounding and decoupling arrangements for every channel; otherwise channel-to-channel performance can vary even though all four amplifiers share the same package.
Treat the non-inverting input as a high-impedance node and minimize its copper area when driving a high-impedance source. The 2 nA input bias current can create error when multiplied by a large source impedance, while the 20 nA input offset current contributes to input-referred error. Use guarding, shielding, or a nearby low-input-bias buffer when leakage and surface contamination would otherwise dominate the measurement.
Do not assume that every quad operational amplifier is pin-compatible with LM2902WYDT. Confirm the 14-SO pin map, amplifier-channel ordering, supply-pin arrangement, common-mode input range, and output-swing limits before substitution. In particular, a familiar 14-pin quad amplifier may use rail-to-rail input stages while LM2902WYDT retains different common-mode and output-swing boundaries, which can make an apparently identical footprint electrically unsuitable.
Keep each closed-loop gain compatible with the 1.3 MHz gain-bandwidth product. A high-gain configuration has less usable bandwidth and can become sensitive to parasitic capacitance around the inverting input. Use resistor values that preserve closed-loop stability, avoid excessively long feedback traces, and verify settling behavior when the channel drives an ADC, DAC, or switched-capacitor load.
अनुपालन जानकारी
The distributor product record identifies LM2902WYDT as RoHS compliant. No additional compliance claims are stated.