LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903BIDDFR ✓ सक्रियLM2903BIDDFR अवलोकन
A comparator is an analog semiconductor that compares two input voltages and produces a logic-level result indicating which input is higher. A dual comparator integrates two comparison channels into one package, allowing simultaneous sensing, threshold detection, or window monitoring. Within the broader hierarchy, the LM2903B belongs to the comparator and amplifier IC family and ultimately to the wider semiconductor and signal-conditioning market.
The LM2903BIDDFR combines an open-collector output stage with a differential-input architecture. Open-collector outputs can pull a logic node low when the comparator changes state, while an external pull-up resistor establishes the high state. This arrangement provides flexible interface voltage selection and is useful with TTL, MOS, and CMOS-compatible loads. Each channel supports independently routed non-inverting and inverting inputs.
The B-version product family provides improved characteristics relative to earlier LM2903, LM293, and LM393 variants while maintaining pin-for-pin drop-in compatibility. The manufacturer identifies LM2903B as a drop-in replacement for the earlier devices, and its common-mode input range includes ground. These features make the comparator suitable for systems that compare bipolar or single-ended sensor signals without requiring a fully differential amplifier.
Typical applications include industrial control systems, automatic test equipment, power-supply supervision, motor-control circuits, window comparators, and general threshold detection. The dual-channel configuration can implement two independent safety thresholds, compare upper and lower limits, or monitor complementary sensor outputs without requiring two separate comparator packages.
The primary design consideration is the open-collector output: each output requires an appropriate pull-up resistor and must remain compatible with the voltage and timing requirements of the connected logic circuit. Input polarity, output state, and propagation behavior should be checked against the specific logic levels and system timing before production release.
This page combines the exact ordering information, package details, operating limits, application guidance, and design considerations for the LM2903BIDDFR. It also organizes sourcing questions and replacement guidance around the device's actual dual-comparator function and open-collector interface.
के लिए ड्रॉप-इन विकल्प LM2903BIDDFR — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2903BIDDFR (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.
LM393BIDDFR
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →LM2903BIDDFRQ1
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM2903BIDDFR Maximum Ratings और Electrical Characteristics
| Comparator Type | Dual standard general-purpose comparator |
| Grade | Industrial grade |
| आउटपुट प्रकार | Open-collector |
| Input Common-Mode Capability | Rail-to-rail |
| Number of Channels | 2 channels |
| ऑपरेटिंग तापमान रेंज | -40°C to 125°C |
| पैकेज | 8-pin SOT-23-THN (DDF) |
| माउंटिंग प्रकार | Surface mount |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
LM2903BIDDFR 8-pin sot-23-thn (ddf) पिन कॉन्फ़िगरेशन गाइड
LM2903BIDDFR (8-pin sot-23-thn (ddf) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: LM2903BIDDFR.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
LM2903BIDDFR के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Control Threshold Detection, Power-Supply Supervision, Motor and Valve Feedback Monitoring, Test and Measurement Equipment, Sensor Signal Conditioning, Battery and Portable-System Monitoring.
Industrial Control Threshold Detection
The LM2903BIDDFR fits industrial control designs that compare a process or control signal against a fixed threshold. Its two channels provide independent decisions without requiring two comparator packages, while the -40°C to 125°C operating range suits equipment exposed to extended industrial temperature conditions. The open-collector outputs can each drive a pulled-up logic node, allowing the same device to interface with TTL, MOS, or CMOS-compatible circuitry. A practical implementation places one input on the reference voltage and the other on the sensed signal, then uses the output state to request an alarm or state transition.
अनुशंसित
Power-Supply Supervision
The LM2903BIDDFR can supervise a power rail by comparing a divided feedback voltage with a reference level. One channel may monitor the upper supply limit while the second monitors a lower limit, creating a window-detection function with only one package. Its two open-collector outputs provide flexible pull-up arrangements for system fault inputs, and the -40°C to 125°C specification supports monitoring inside industrial equipment. Design the divider values for the intended threshold and verify the common-mode and supply limits against the manufacturer electrical-characteristics table before deployment.
अनुशंसित
Motor and Valve Feedback Monitoring
The LM2903BIDDFR is useful for monitoring motor-drive or valve-position feedback where two analog signals must be compared. One channel can evaluate the sensor signal against a limit, while the other can perform complementary direction or overtravel detection. Its open-collector output can pull up an enable, fault, or digital-input node, reducing the need for a separate pull-down driver. The dual-channel configuration also saves board area in compact industrial controllers, while the industrial temperature range supports equipment outside controlled consumer environments.
अनुशंसित
Test and Measurement Equipment
The LM2903BIDDFR can support limit detection in automated test equipment where a measured node must be checked against upper and lower boundaries. Two independent channels can each compare a measurement against a reference and produce a logic result for the test controller. Open-collector outputs make it possible to select a pull-up voltage that matches the surrounding test electronics. The compact 8-pin SOT-23-THN package helps conserve board area, and the -40°C to 125°C operating range supports instrument environments with elevated internal temperatures.
अनुशंसित
Sensor Signal Conditioning
The LM2903BIDDFR can convert a sensor-derived analog condition into a logic event for a controller or safety chain. The comparator compares the conditioned sensor voltage with a threshold, while its open-collector output provides a wired signal that can be pulled up to the receiving logic voltage. Two channels allow the same board to monitor two sensor conditions or implement hysteresis around one threshold. The -40°C to 125°C range is valuable in industrial sensing systems, although the final circuit must account for sensor noise, input offset, and the propagation delay listed in the manufacturer datasheet.
अनुशंसित
Battery and Portable-System Monitoring
The LM2903BIDDFR can be used in battery-powered equipment to detect an undervoltage or overvoltage condition before the connected electronics becomes unreliable. Dividing the battery voltage and comparing it with a reference allows either channel to generate a pulled-up fault signal. The open-collector interface avoids tying the logic-high level to one fixed internal voltage, while the compact 8-pin package helps limit board size. For portable products, check the device's supply and common-mode limits at the lowest battery voltage and confirm that quiescent-current requirements fit the system power budget.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM2903BIDDFR — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM393BIDDFR | LM2903BIDDFRQ1 |
|---|---|---|---|
| Package | 8-pin SOT-23-THN (DDF) | 8-pin SOT-23-THN (DDF) | 8-pin SOT-23-THN (DDF) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Configuration | Dual | Dual | Dual |
| Output Type | Open-collector | Open-collector | Open-collector |
| Number of Pins | 8 pins | 8 pins | 8 pins |
मुख्य विशेषताएँ
- Two independent open-collector channels in a compact surface-mount package (बनामLM393BIDDFR)
- Industrial-grade LM2903B family positioning (बनामLM2903BIDDFRQ1)
- Flexible open-collector logic interface (बनामLM393BIDDFR)
डिज़ाइन नोट्स
Treat each open-collector output as requiring external pull-up circuitry. The device can sink current but cannot actively drive the output high. Select the pull-up voltage to remain within the connected gate or logic input limits, and calculate the resistor from the required sink current and maximum bus rise time. Do not connect multiple outputs directly together unless the application logic explicitly supports wired open-collector operation.
Place pull-up resistors close to the comparator outputs or the receiving logic inputs to limit trace capacitance and ringing. Route the two input pairs away from switching nodes and high-current paths, and keep the ground connection short to the device ground pin. Because the exact pin assignments are defined by the manufacturer pin-description table, verify them against the selected DDF footprint rather than relying only on a generic 8-pin comparator drawing.
Check minimum and maximum supply voltage, input common-mode range, differential input limits, and output-current limits in the manufacturer electrical-characteristics table. These constraints determine whether the sensed signal remains valid and whether the open-collector pull-up can be driven correctly. Confirm that the -40°C to 125°C operating rating covers the full intended ambient and self-heating conditions.
Use hysteresis or positive feedback when the compared signal can cross the threshold slowly, because input offset and noise near the decision point can cause repeated output transitions. The resistance and capacitance at the input network also affect response time. Verify propagation delay and output timing in the final circuit rather than assuming switching is instantaneous.
अनुपालन जानकारी
The device is an industrial-grade comparator, but no specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or AEC-Q100 declaration appears in the available product-page information.