Texas Instruments

LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments

MPN: LM2903BIDDFR ✓ פעיל
8-pin SOT-23-THN (DDF) Package
כמות הזמנה מינימלית: 1 |

LM2903BIDDFR סקירה

The Texas Instruments LM2903BIDDFR is a dual industrial-grade standard comparator with two independent comparison channels, open-collector outputs, and rail-to-rail input capability. It is packaged in an 8-pin SOT-23-THN (DDF) surface-mount package and is specified for an operating temperature range of -40°C to 125°C.

A comparator is an analog semiconductor that compares two input voltages and produces a logic-level result indicating which input is higher. A dual comparator integrates two comparison channels into one package, allowing simultaneous sensing, threshold detection, or window monitoring. Within the broader hierarchy, the LM2903B belongs to the comparator and amplifier IC family and ultimately to the wider semiconductor and signal-conditioning market.

The LM2903BIDDFR combines an open-collector output stage with a differential-input architecture. Open-collector outputs can pull a logic node low when the comparator changes state, while an external pull-up resistor establishes the high state. This arrangement provides flexible interface voltage selection and is useful with TTL, MOS, and CMOS-compatible loads. Each channel supports independently routed non-inverting and inverting inputs.

The B-version product family provides improved characteristics relative to earlier LM2903, LM293, and LM393 variants while maintaining pin-for-pin drop-in compatibility. The manufacturer identifies LM2903B as a drop-in replacement for the earlier devices, and its common-mode input range includes ground. These features make the comparator suitable for systems that compare bipolar or single-ended sensor signals without requiring a fully differential amplifier.

Typical applications include industrial control systems, automatic test equipment, power-supply supervision, motor-control circuits, window comparators, and general threshold detection. The dual-channel configuration can implement two independent safety thresholds, compare upper and lower limits, or monitor complementary sensor outputs without requiring two separate comparator packages.

The primary design consideration is the open-collector output: each output requires an appropriate pull-up resistor and must remain compatible with the voltage and timing requirements of the connected logic circuit. Input polarity, output state, and propagation behavior should be checked against the specific logic levels and system timing before production release.

This page combines the exact ordering information, package details, operating limits, application guidance, and design considerations for the LM2903BIDDFR. It also organizes sourcing questions and replacement guidance around the device's actual dual-comparator function and open-collector interface.

חלופות תחליף ישיר עבור LM2903BIDDFR — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם LM2903BIDDFR (אותו גורם צורה וטביעת רגל) — שונים ב Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.

Texas Instruments
Comparator Type: Dual differential comparator
Grade: Commercial grade
Number of Channels: 2 independent channels
השווה עם LM2903BIDDFR →

LM393BIDDFR

✅ Drop-In ⚠️ מפרטים לא מאומתים
Texas Instruments
📦 8-pin SOT-23-THN (DDF)
Dual differential comparator · 2 independent channels · 38 V · 0.37 mV · 3.5 nA · 200 uA per comparator · 1 us · 2 kV

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

LM2903BIDDFRQ1

✅ Drop-In ⚠️ מפרטים לא מאומתים
📦 8-pin SOT-23-THN (DDF)
Same LM2903B dual-comparator architecture and DDF footprint, with the Q1 ordering designation indicating a different qualification grade; estimated key-parameter proximity is 90%.

📋 חלופה להתייחסות (לא בקטלוג)

LM2903BIDDFR דירוגים מרביים ומאפיינים חשמליים

Comparator Type Dual standard general-purpose comparator
Grade Industrial grade
סוג פלט Open-collector
Input Common-Mode Capability Rail-to-rail
Number of Channels 2 channels
טווח טמפרטורת פעולה -40°C to 125°C
מארז 8-pin SOT-23-THN (DDF)
סוג הרכבה Surface mount
Logic Compatibility TTL, MOS, and CMOS compatible

מדריך תצורת פינים של LM2903BIDDFR 8-pin sot-23-thn (ddf)

תצורת פינים עבור LM2903BIDDFR (מארזת 8-pin sot-23-thn (ddf)). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.

תרשים פינים של מארזת 8-pin sot-23-thn (ddf) עבור LM2903BIDDFR

אין נתוני פריסת פינים מפורטים עבור LM2903BIDDFR.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

LM2903BIDDFR מתאים עבור 6 יישוםs: Industrial Control Threshold Detection, Power-Supply Supervision, Motor and Valve Feedback Monitoring, Test and Measurement Equipment, Sensor Signal Conditioning, Battery and Portable-System Monitoring.

🏭

Industrial Control Threshold Detection

The LM2903BIDDFR fits industrial control designs that compare a process or control signal against a fixed threshold. Its two channels provide independent decisions without requiring two comparator packages, while the -40°C to 125°C operating range suits equipment exposed to extended industrial temperature conditions. The open-collector outputs can each drive a pulled-up logic node, allowing the same device to interface with TTL, MOS, or CMOS-compatible circuitry. A practical implementation places one input on the reference voltage and the other on the sensed signal, then uses the output state to request an alarm or state transition.

⚡

Power-Supply Supervision

The LM2903BIDDFR can supervise a power rail by comparing a divided feedback voltage with a reference level. One channel may monitor the upper supply limit while the second monitors a lower limit, creating a window-detection function with only one package. Its two open-collector outputs provide flexible pull-up arrangements for system fault inputs, and the -40°C to 125°C specification supports monitoring inside industrial equipment. Design the divider values for the intended threshold and verify the common-mode and supply limits against the manufacturer electrical-characteristics table before deployment.

🔧

Motor and Valve Feedback Monitoring

The LM2903BIDDFR is useful for monitoring motor-drive or valve-position feedback where two analog signals must be compared. One channel can evaluate the sensor signal against a limit, while the other can perform complementary direction or overtravel detection. Its open-collector output can pull up an enable, fault, or digital-input node, reducing the need for a separate pull-down driver. The dual-channel configuration also saves board area in compact industrial controllers, while the industrial temperature range supports equipment outside controlled consumer environments.

📟

Test and Measurement Equipment

The LM2903BIDDFR can support limit detection in automated test equipment where a measured node must be checked against upper and lower boundaries. Two independent channels can each compare a measurement against a reference and produce a logic result for the test controller. Open-collector outputs make it possible to select a pull-up voltage that matches the surrounding test electronics. The compact 8-pin SOT-23-THN package helps conserve board area, and the -40°C to 125°C operating range supports instrument environments with elevated internal temperatures.

🧩

Sensor Signal Conditioning

The LM2903BIDDFR can convert a sensor-derived analog condition into a logic event for a controller or safety chain. The comparator compares the conditioned sensor voltage with a threshold, while its open-collector output provides a wired signal that can be pulled up to the receiving logic voltage. Two channels allow the same board to monitor two sensor conditions or implement hysteresis around one threshold. The -40°C to 125°C range is valuable in industrial sensing systems, although the final circuit must account for sensor noise, input offset, and the propagation delay listed in the manufacturer datasheet.

📱

Battery and Portable-System Monitoring

The LM2903BIDDFR can be used in battery-powered equipment to detect an undervoltage or overvoltage condition before the connected electronics becomes unreliable. Dividing the battery voltage and comparing it with a reference allows either channel to generate a pulled-up fault signal. The open-collector interface avoids tying the logic-high level to one fixed internal voltage, while the compact 8-pin package helps limit board size. For portable products, check the device's supply and common-mode limits at the lowest battery voltage and confirm that quiescent-current requirements fit the system power budget.

What is the LM2903BIDDFR?
The LM2903BIDDFR is a Texas Instruments dual industrial-grade standard comparator with two open-collector outputs in an 8-pin SOT-23-THN package. According to the TI LM2903B product page, the device combines rail-to-rail input capability with common-mode operation that includes ground. It is intended for voltage-threshold comparison, signal conditioning, and industrial control applications.
What are the key specifications of LM2903BIDDFR that engineers should know?
The key specifications of the LM2903BIDDFR are two independent comparator channels, open-collector outputs, rail-to-rail input capability, and an operating temperature range of -40°C to 125°C. According to the TI LM2903B product page, it is an industrial-grade standard comparator supplied in an 8-pin SOT-23-THN (DDF) package. The open-collector outputs require external pull-up circuitry.
Where can I download the LM2903BIDDFR datasheet PDF?
The official LM2903BIDDFR documentation is available through the Texas Instruments LM2903B product page linked on this page. That page provides the manufacturer datasheet, ordering details, pin information, and product parameters. For a controlled engineering review, use the manufacturer document associated with the LM2903B family and confirm that the ordering table includes the DDF package suffix.
Where can I find the LM2903BIDDFR pinout?
The LM2903BIDDFR pinout is published in the manufacturer documentation for the LM2903B family and should be reviewed before PCB routing. The exact orderable device uses an 8-pin SOT-23-THN (DDF) package. Use the pin-description table in the manufacturer datasheet when assigning the two input pairs, outputs, supply, and ground connections.
What is the operating temperature range of LM2903BIDDFR?
The LM2903BIDDFR is specified for operation from -40°C to 125°C. The TI part-details information identifies the DDF package as an 8-pin SOT-23-THN device and the LM2903B family as industrial grade. This temperature range allows use in industrial equipment where ambient temperatures may exceed typical consumer-product conditions.
What supply voltage does LM2903BIDDFR accept?
The LM2903BIDDFR belongs to the LM2903B dual-comparator family, but its exact supply-voltage limits are not stated in the product-page excerpt. Before connecting the device, consult the electrical-characteristics table in the manufacturer datasheet for minimum and maximum supply voltage, supply-current behavior, and common-mode limits. Those limits determine both operating range and input-signal compatibility.
Does LM2903BIDDFR have open-collector outputs?
Yes, the LM2903BIDDFR has two open-collector outputs. According to the DigiKey product listing, it is an open-collector, rail-to-rail dual comparator. Each output can sink current to pull its connected node low, while a suitable external pull-up resistor determines the high-state voltage.
How should the LM2903BIDDFR open-collector output be wired?
Connect a suitable pull-up resistor from each open-collector output node to the logic supply used by the receiving circuit. The comparator sinks the node when its output is active and releases it when inactive, allowing the pull-up voltage to establish the inactive logic level. Select the resistor to balance sink-current capability, rise time, and signal-bus loading.
Where can I buy LM2903BIDDFR online?
Use the Request a Quote form on this page to request LM2903BIDDFR availability, current commercial terms, and lead time from XAIPART. The form is the appropriate channel for an exact orderable MPN because it accepts the full suffix LM2903BIDDFR, including the DDF package and tape-and-reel ordering information where applicable.
What is the price of LM2903BIDDFR?
Use the Request a Quote form on this page for the current commercial quotation for LM2903BIDDFR. Commercial terms can depend on order quantity, packaging, schedule, and market conditions, so a static quotation can become stale. The exact MPN entered in the request helps prevent confusion with other LM2903 package and grade variants.
What is the lead time for LM2903BIDDFR?
The current lead time for LM2903BIDDFR should be requested through the Request a Quote form on this page. The form can be completed with the exact device name, required quantity, and delivery target. If the complete orderable suffix is required for the shipment, include LM2903BIDDFR as written on the product page.
Is LM2903BIDDFR in stock?
Request current LM2903BIDDFR stock and allocation status through the Request a Quote form on this page. Inventory can vary by package, order quantity, and purchasing schedule, so the Request a Quote response should be treated as the current commercial confirmation. Include your required quantity and target delivery date in the request.
What is the difference between LM2903BIDDFR and LM2903BIDR?
LM2903BIDDFR and LM2903BIDR belong to the same dual-comparator family, but their package suffixes identify different physical packages. LM2903BIDDFR is the 8-pin SOT-23-THN DDF version, while LM2903BIDR is associated with an 8-pin SOIC package. Because their land patterns are not interchangeable, they are not drop-in PCB replacements for one another.
When should I choose LM2903BIDDFR instead of another dual comparator?
Choose LM2903BIDDFR when the design needs two industrial-grade comparison channels, open-collector outputs, and a compact 8-pin SOT-23-THN package. It is particularly suitable when the output bus requires a selectable pull-up voltage or when one package must provide two independent threshold decisions. Choose a different pin-compatible variant only after confirming electrical and qualification requirements.
Is LM2903BIDDFR suitable for industrial threshold detection?
Yes, the LM2903BIDDFR is suitable for many industrial threshold-detection systems because it is an industrial-grade dual comparator with an operating range of -40°C to 125°C. Its open-collector outputs can drive pulled-up logic nodes, while the two channels can monitor independent limits. The final design must still verify supply voltage, common-mode range, timing, and output-current requirements.
Can LM2903BIDDFR replace LM2903BIDR on the same PCB?
No, LM2903BIDDFR cannot directly replace LM2903BIDR on an existing PCB because the DDF SOT-23-THN and SOIC packages use different footprints and dimensions. Although both provide a dual open-collector comparator function, PCB compatibility requires the same land pattern and pin arrangement. Choose the package suffix matching the board or redesign the footprint.
What can replace LM2903BIDDFR?
A valid replacement must use the same 8-pin SOT-23-THN land pattern, preserve the dual open-collector interface, and meet the supply, common-mode, timing, and temperature requirements of the original circuit. The LM2903B family includes related orderable variants, but package suffixes must be checked carefully. Use the manufacturer cross-reference and datasheet pin tables before approving a substitution.

נתוני עזר הנדסיים עבור LM2903BIDDFR — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose LM2903BIDDFR for compact industrial designs that require two independent threshold comparisons, open-collector outputs, and operation from -40°C to 125°C. It is especially useful when the logic-high voltage must be selected externally through pull-up resistors or when one package must monitor two separate conditions. LM393BIDDFR is a closely related same-package option for equivalent dual open-collector threshold functions, but the final choice should be based on the exact electrical limits and qualification requirements of each ordering code. LM2903BIDDFRQ1 is appropriate when the Q1 qualification designation is needed for the target application. Do not substitute LM2903BIDR on an existing board because the SOIC footprint differs from the DDF SOT-23-THN footprint. For any alternative, verify supply voltage, common-mode range, propagation delay, input offset, output sink current, temperature rating, and pin compatibility before release.

השוואה עם חלופות

פרמטר מוצר זה LM393BIDDFR LM2903BIDDFRQ1
Package 8-pin SOT-23-THN (DDF) 8-pin SOT-23-THN (DDF) 8-pin SOT-23-THN (DDF)
Brand Texas Instruments Texas Instruments Texas Instruments
Comparator Configuration Dual Dual Dual
Output Type Open-collector Open-collector Open-collector
Number of Pins 8 pins 8 pins 8 pins

מבדילים עיקריים

  • Two independent open-collector channels in a compact surface-mount package (לעומתLM393BIDDFR)
  • Industrial-grade LM2903B family positioning (לעומתLM2903BIDDFRQ1)
  • Flexible open-collector logic interface (לעומתLM393BIDDFR)

הערות תכנון

Treat each open-collector output as requiring external pull-up circuitry. The device can sink current but cannot actively drive the output high. Select the pull-up voltage to remain within the connected gate or logic input limits, and calculate the resistor from the required sink current and maximum bus rise time. Do not connect multiple outputs directly together unless the application logic explicitly supports wired open-collector operation.

Place pull-up resistors close to the comparator outputs or the receiving logic inputs to limit trace capacitance and ringing. Route the two input pairs away from switching nodes and high-current paths, and keep the ground connection short to the device ground pin. Because the exact pin assignments are defined by the manufacturer pin-description table, verify them against the selected DDF footprint rather than relying only on a generic 8-pin comparator drawing.

Check minimum and maximum supply voltage, input common-mode range, differential input limits, and output-current limits in the manufacturer electrical-characteristics table. These constraints determine whether the sensed signal remains valid and whether the open-collector pull-up can be driven correctly. Confirm that the -40°C to 125°C operating rating covers the full intended ambient and self-heating conditions.

Use hysteresis or positive feedback when the compared signal can cross the threshold slowly, because input offset and noise near the decision point can cause repeated output transitions. The resistance and capacitance at the input network also affect response time. Verify propagation delay and output timing in the final circuit rather than assuming switching is instantaneous.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

The device is an industrial-grade comparator, but no specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or AEC-Q100 declaration appears in the available product-page information.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LM2903BIDDFR datasheet LM2903BIDDFR specifications LM2903BIDDFR pinout LM2903BIDDFR datasheet pdf LM2903BIDDFR equivalent LM2903BIDDFR replacement LM2903BIDDFR footprint LM2903BIDDFR price LM2903BIDDFR stock Texas Instruments LM2903BIDDFR LM2903BIDDFR vs LM393BIDDFR LM2903BIDDFR application circuit

רכיבים ומונחים קשורים

Texas Instruments LM2903BIDDFR LM2903B LM393BIDDFR LM2903BIDDFRQ1 LM2903BIDR BA2903F-E2 dual comparator standard comparator general-purpose comparator open-collector output rail-to-rail input common-mode input voltage differential input voltage SOT-23-THN DDF package 8-pin surface-mount package semiconductor analog signal conditioning industrial control power-supply supervision threshold detection TTL compatibility CMOS compatibility MOS compatibility
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר