LM2903BIDDFR - Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903BIDDFR ✓ 啟用中LM2903BIDDFR 概覽
A comparator is an analog semiconductor that compares two input voltages and produces a logic-level result indicating which input is higher. A dual comparator integrates two comparison channels into one package, allowing simultaneous sensing, threshold detection, or window monitoring. Within the broader hierarchy, the LM2903B belongs to the comparator and amplifier IC family and ultimately to the wider semiconductor and signal-conditioning market.
The LM2903BIDDFR combines an open-collector output stage with a differential-input architecture. Open-collector outputs can pull a logic node low when the comparator changes state, while an external pull-up resistor establishes the high state. This arrangement provides flexible interface voltage selection and is useful with TTL, MOS, and CMOS-compatible loads. Each channel supports independently routed non-inverting and inverting inputs.
The B-version product family provides improved characteristics relative to earlier LM2903, LM293, and LM393 variants while maintaining pin-for-pin drop-in compatibility. The manufacturer identifies LM2903B as a drop-in replacement for the earlier devices, and its common-mode input range includes ground. These features make the comparator suitable for systems that compare bipolar or single-ended sensor signals without requiring a fully differential amplifier.
Typical applications include industrial control systems, automatic test equipment, power-supply supervision, motor-control circuits, window comparators, and general threshold detection. The dual-channel configuration can implement two independent safety thresholds, compare upper and lower limits, or monitor complementary sensor outputs without requiring two separate comparator packages.
The primary design consideration is the open-collector output: each output requires an appropriate pull-up resistor and must remain compatible with the voltage and timing requirements of the connected logic circuit. Input polarity, output state, and propagation behavior should be checked against the specific logic levels and system timing before production release.
This page combines the exact ordering information, package details, operating limits, application guidance, and design considerations for the LM2903BIDDFR. It also organizes sourcing questions and replacement guidance around the device's actual dual-comparator function and open-collector interface.
直接替換替代品,適用於 LM2903BIDDFR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2903BIDDFR (相同外形與佔位) — 差異在於 Comparator Type, Grade, Number of Channels, Operating Temperature Range, Output Type.
LM393BIDDFR
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM2903BIDDFRQ1
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
LM2903BIDDFR 最大額定值與電氣特性
| Comparator Type | Dual standard general-purpose comparator |
| Grade | Industrial grade |
| 輸出類型 | Open-collector |
| Input Common-Mode Capability | Rail-to-rail |
| Number of Channels | 2 channels |
| 工作溫度範圍 | -40°C to 125°C |
| 封裝 | 8-pin SOT-23-THN (DDF) |
| 安裝類型 | Surface mount |
| Logic Compatibility | TTL, MOS, and CMOS compatible |
LM2903BIDDFR 8-pin sot-23-thn (ddf) 腳位配置指南
LM2903BIDDFR(8-pin sot-23-thn (ddf) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LM2903BIDDFR.
請參閱 資料表 以查看完整腳位配置。
典型應用
LM2903BIDDFR 適用於 6 應用s: Industrial Control Threshold Detection, Power-Supply Supervision, Motor and Valve Feedback Monitoring, Test and Measurement Equipment, Sensor Signal Conditioning, Battery and Portable-System Monitoring.
Industrial Control Threshold Detection
The LM2903BIDDFR fits industrial control designs that compare a process or control signal against a fixed threshold. Its two channels provide independent decisions without requiring two comparator packages, while the -40°C to 125°C operating range suits equipment exposed to extended industrial temperature conditions. The open-collector outputs can each drive a pulled-up logic node, allowing the same device to interface with TTL, MOS, or CMOS-compatible circuitry. A practical implementation places one input on the reference voltage and the other on the sensed signal, then uses the output state to request an alarm or state transition.
推薦
Power-Supply Supervision
The LM2903BIDDFR can supervise a power rail by comparing a divided feedback voltage with a reference level. One channel may monitor the upper supply limit while the second monitors a lower limit, creating a window-detection function with only one package. Its two open-collector outputs provide flexible pull-up arrangements for system fault inputs, and the -40°C to 125°C specification supports monitoring inside industrial equipment. Design the divider values for the intended threshold and verify the common-mode and supply limits against the manufacturer electrical-characteristics table before deployment.
推薦
Motor and Valve Feedback Monitoring
The LM2903BIDDFR is useful for monitoring motor-drive or valve-position feedback where two analog signals must be compared. One channel can evaluate the sensor signal against a limit, while the other can perform complementary direction or overtravel detection. Its open-collector output can pull up an enable, fault, or digital-input node, reducing the need for a separate pull-down driver. The dual-channel configuration also saves board area in compact industrial controllers, while the industrial temperature range supports equipment outside controlled consumer environments.
推薦
Test and Measurement Equipment
The LM2903BIDDFR can support limit detection in automated test equipment where a measured node must be checked against upper and lower boundaries. Two independent channels can each compare a measurement against a reference and produce a logic result for the test controller. Open-collector outputs make it possible to select a pull-up voltage that matches the surrounding test electronics. The compact 8-pin SOT-23-THN package helps conserve board area, and the -40°C to 125°C operating range supports instrument environments with elevated internal temperatures.
推薦
Sensor Signal Conditioning
The LM2903BIDDFR can convert a sensor-derived analog condition into a logic event for a controller or safety chain. The comparator compares the conditioned sensor voltage with a threshold, while its open-collector output provides a wired signal that can be pulled up to the receiving logic voltage. Two channels allow the same board to monitor two sensor conditions or implement hysteresis around one threshold. The -40°C to 125°C range is valuable in industrial sensing systems, although the final circuit must account for sensor noise, input offset, and the propagation delay listed in the manufacturer datasheet.
推薦
Battery and Portable-System Monitoring
The LM2903BIDDFR can be used in battery-powered equipment to detect an undervoltage or overvoltage condition before the connected electronics becomes unreliable. Dividing the battery voltage and comparing it with a reference allows either channel to generate a pulled-up fault signal. The open-collector interface avoids tying the logic-high level to one fixed internal voltage, while the compact 8-pin package helps limit board size. For portable products, check the device's supply and common-mode limits at the lowest battery voltage and confirm that quiescent-current requirements fit the system power budget.
推薦
推薦產品摘要
工程參考資料,適用於 LM2903BIDDFR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM393BIDDFR | LM2903BIDDFRQ1 |
|---|---|---|---|
| Package | 8-pin SOT-23-THN (DDF) | 8-pin SOT-23-THN (DDF) | 8-pin SOT-23-THN (DDF) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Configuration | Dual | Dual | Dual |
| Output Type | Open-collector | Open-collector | Open-collector |
| Number of Pins | 8 pins | 8 pins | 8 pins |
主要差異化特點
- Two independent open-collector channels in a compact surface-mount package (對比LM393BIDDFR)
- Industrial-grade LM2903B family positioning (對比LM2903BIDDFRQ1)
- Flexible open-collector logic interface (對比LM393BIDDFR)
設計說明
Treat each open-collector output as requiring external pull-up circuitry. The device can sink current but cannot actively drive the output high. Select the pull-up voltage to remain within the connected gate or logic input limits, and calculate the resistor from the required sink current and maximum bus rise time. Do not connect multiple outputs directly together unless the application logic explicitly supports wired open-collector operation.
Place pull-up resistors close to the comparator outputs or the receiving logic inputs to limit trace capacitance and ringing. Route the two input pairs away from switching nodes and high-current paths, and keep the ground connection short to the device ground pin. Because the exact pin assignments are defined by the manufacturer pin-description table, verify them against the selected DDF footprint rather than relying only on a generic 8-pin comparator drawing.
Check minimum and maximum supply voltage, input common-mode range, differential input limits, and output-current limits in the manufacturer electrical-characteristics table. These constraints determine whether the sensed signal remains valid and whether the open-collector pull-up can be driven correctly. Confirm that the -40°C to 125°C operating rating covers the full intended ambient and self-heating conditions.
Use hysteresis or positive feedback when the compared signal can cross the threshold slowly, because input offset and noise near the decision point can cause repeated output transitions. The resistance and capacitance at the input network also affect response time. Verify propagation delay and output timing in the final circuit rather than assuming switching is instantaneous.
合規資訊
The device is an industrial-grade comparator, but no specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or AEC-Q100 declaration appears in the available product-page information.