LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics
MPN: LM2904WHYST ✓ सक्रियLM2904WHYST अवलोकन
An operational amplifier is an analog amplifier that uses very high open-loop gain to compare or amplify a differential input signal. The LM2904 family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, comparator, and rail-to-rail amplifier categories. The LM2904WHYST is intended for applications requiring two amplifiers, moderate bandwidth, low input bias current, and a compact surface-mount footprint rather than precision or high-speed performance.
Key features include two amplifier channels, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 200 nA input bias current, and 7 mV input offset voltage as identified for this device. The MiniSO-8 package reduces board area while retaining separate power, ground, input, and output connections for each channel. The automotive-oriented ordering code also supports use in temperature-qualified equipment, subject to the device's stated operating limits.
Each channel operates as a general-purpose voltage-feedback amplifier, allowing implementation as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style circuit, or active filter. The two independent channels can process separate signals or be combined for differential, instrumentation, and gain-stage arrangements. The 1.1 MHz bandwidth is suitable for low-to-moderate frequency industrial signals, while the 0.6 V/us slew rate supports accurate reproduction of relatively slow input waveforms.
Typical applications include low-side current sensing, industrial sensor interfaces, transducer amplification, audio preamplification, and general control loops. In each case, the low input bias current helps reduce source-loading errors, while the dual configuration can reduce the number of separate amplifier packages required on a board. The amplifier is best suited to signals where moderate bandwidth and common-mode performance are more important than rail-to-rail operation or very low offset.
Designers should verify the input common-mode range, output swing, supply voltage, and stability requirements against the operating conditions before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode voltage. Feedback-network values and source capacitance should be selected to maintain stable closed-loop operation across the intended gain and load range.
This product record combines package, electrical, qualification, sourcing, and drop-in comparison information with practical circuit guidance. It is intended to accelerate engineering selection for compact dual-op-amp designs while clearly distinguishing direct replacements from alternatives that require compatibility review.
के लिए ड्रॉप-इन विकल्प LM2904WHYST — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं LM2904WHYST (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Number of Channels, Slew Rate, Input Bias Current, Amplifier Type.
LM2904YDT
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →LM358DT
✅ ड्रॉप-इन✗ स्टॉक में नहीं
$0.0509 / यूनिट
डेटाशीट देखें →TLV6002
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MCP6002-I/SN
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →RC4558
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
LM2904WHYST Maximum Ratings और Electrical Characteristics
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 0.6 V/us |
| Input Bias Current | 200 nA |
| Input Offset Voltage | 7 mV |
| पैकेज | 8-pin MiniSO |
| Body Width | 3.90 mm |
| माउंटिंग प्रकार | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
| Maximum Rated Operating Temperature | 150 C |
| Product Type | Single-ended amplifier circuit |
| Signal Chain Role | General-purpose signal amplification |
LM2904WHYST पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Output of amplifier channel 1 |
| पिन 2 | IN-1 — Inverting input of amplifier channel 1 |
| पिन 3 | IN+1 — Non-inverting input of amplifier channel 1 |
| पिन 4 | V- — Negative supply or ground connection |
| पिन 5 | IN+2 — Non-inverting input of amplifier channel 2 |
| पिन 6 | IN-2 — Inverting input of amplifier channel 2 |
| पिन 7 | OUT2 — Output of amplifier channel 2 |
| पिन 8 | V+ — Positive supply connection |
सामान्य अनुप्रयोग
LM2904WHYST के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Sensor Signal Conditioning, Low-Side Current Sensing, Audio Preamplification, Active Filter and Control Loop, Automotive Control and Monitoring, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM2904WHYST fits low-frequency industrial sensor interfaces because its 200 nA input bias current limits errors when measuring sources with relatively high output impedance. A 1.1 MHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensors, while the 0.6 V/us slew rate supports gradual sensor changes. Both channels can amplify or filter related signals on the same board. The design must keep sensor input voltages inside the amplifier’s common-mode range and verify output swing at the selected supply voltage.
अनुशंसित
Low-Side Current Sensing
LM2904WHYST can amplify the small voltage developed across a low-side current-sense resistor without introducing a large package-count penalty. Its 200 nA input bias current is valuable when the sense-resistor node has limited source impedance, and the 1.1 MHz bandwidth accommodates many power-conversion control signals. One channel may serve the measurement amplifier while the other provides gain or filtering. Verify common-mode limits during startup, transient response, and operation when the measured node approaches either supply rail.
अनुशंसित
Audio Preamplification
The LM2904WHYST is appropriate for modest audio preamplifier stages that need two channels and do not require rail-to-rail input or output operation. Its 200 nA input bias current is compatible with many low-impedance audio sources, while the 1.1 MHz gain-bandwidth product is sufficient for voice-band and conventional audio signal paths. Each channel can implement gain and filtering around the amplifier. The circuit should provide adequate supply headroom for the required output swing and be checked for distortion and stability at the selected closed-loop gain.
अनुशंसित
Active Filter and Control Loop
LM2904WHYST can form the active elements in low-frequency filters and simple analog control loops. A 1.1 MHz gain-bandwidth product leaves useful bandwidth below the device’s unity-gain frequency for common first-order and second-order implementations, and the 0.6 V/us slew rate supports non-abrupt control signals. The two independent channels can implement cascaded stages or complementary functions. Resistor and capacitor tolerances directly determine filter accuracy, while source capacitance and noise gain must be checked to preserve closed-loop stability.
अनुशंसित
Automotive Control and Monitoring
The LM2904WHYST is identified as AEC-Q100 qualified and rated for operation up to 150 C, supporting its use in automotive monitoring and control electronics when all application limits are satisfied. Its two channels can handle complementary sensor signals or separate monitoring functions in a compact MiniSO-8 package. At elevated temperatures, thermal derating and the documented increase in input bias current must be considered, particularly for high-impedance sources. Production validation should confirm the exact ordering code, qualification conditions, voltage range, and worst-case accuracy.
अनुशंसित
Portable Instrumentation
LM2904WHYST is suitable for compact instrumentation requiring two general-purpose analog channels without the footprint of larger dual packages. The 200 nA bias current reduces loading on sensor and divider networks, and the 1.1 MHz bandwidth is suitable for many low-bandwidth measurement channels. It can be used for excitation buffering, differential measurement, or gain stages in portable test equipment. Battery operation requires attention to supply range and current consumption, while signal-ground layout must minimize offsets, noise coupling, and errors from shared return paths.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा LM2904WHYST — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | LM2904YDT | LM358 | TLV6002 | MCP6002 | RC4558 |
|---|---|---|---|---|---|---|
| Package | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Microchip Technology | Renesas Electronics |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.5 MHz |
मुख्य विशेषताएँ
- Higher bandwidth than common LM358-class alternatives (बनामLM358)
- Lower input bias current than rail-to-rail alternatives (बनामTLV6002)
- Automotive qualification and elevated-temperature capability (बनामMCP6002)
- Direct same-family alternative with matching core characteristics (बनामLM2904YDT)
डिज़ाइन नोट्स
Place the supply-bypass capacitor directly between pins 8 and 4, with the ground connection kept short and low impedance. Route the input and feedback traces away from switching nodes and high-current paths. Because both channels are independent, each input should have a defined DC path and each feedback network should connect only to its associated output. Keep the exposed package orientation and pin-1 mark aligned with the manufacturer footprint during PCB assembly.
Check the selected noise gain against the 1.1 MHz gain-bandwidth product and the 0.6 V/us slew rate before using the amplifier at high closed-loop gain. Capacitance at the input and output pins can alter poles and phase margin, especially with long PCB traces. Use short feedback paths and consider small isolation resistors where source or load capacitance is unavoidable. Validate the final circuit with the intended signal amplitude, frequency, supply configuration, and external load.
Do not assume that an 8-pin package guarantees operational interchangeability. The input common-mode range, output swing, supply range, input offset, bias current, noise, and slew behavior must remain valid for every operating condition. If a channel is unused, tie its non-inverting input to a valid common-mode potential rather than allowing it to float. For automotive use, verify the exact grade and account for thermal derating and bias-current growth at elevated ambient temperature.
अनुपालन जानकारी
The AEC-Q100 qualification and 150 C operating rating are identified for LM2904WHYST. Other environmental and material-compliance attributes are not specified in the cited product information.