LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics
N.º da peça: LM2904WHYST ✓ AtivoLM2904WHYST Visão geral
An operational amplifier is an analog amplifier that uses very high open-loop gain to compare or amplify a differential input signal. The LM2904 family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, comparator, and rail-to-rail amplifier categories. The LM2904WHYST is intended for applications requiring two amplifiers, moderate bandwidth, low input bias current, and a compact surface-mount footprint rather than precision or high-speed performance.
Key features include two amplifier channels, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 200 nA input bias current, and 7 mV input offset voltage as identified for this device. The MiniSO-8 package reduces board area while retaining separate power, ground, input, and output connections for each channel. The automotive-oriented ordering code also supports use in temperature-qualified equipment, subject to the device's stated operating limits.
Each channel operates as a general-purpose voltage-feedback amplifier, allowing implementation as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style circuit, or active filter. The two independent channels can process separate signals or be combined for differential, instrumentation, and gain-stage arrangements. The 1.1 MHz bandwidth is suitable for low-to-moderate frequency industrial signals, while the 0.6 V/us slew rate supports accurate reproduction of relatively slow input waveforms.
Typical applications include low-side current sensing, industrial sensor interfaces, transducer amplification, audio preamplification, and general control loops. In each case, the low input bias current helps reduce source-loading errors, while the dual configuration can reduce the number of separate amplifier packages required on a board. The amplifier is best suited to signals where moderate bandwidth and common-mode performance are more important than rail-to-rail operation or very low offset.
Designers should verify the input common-mode range, output swing, supply voltage, and stability requirements against the operating conditions before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode voltage. Feedback-network values and source capacitance should be selected to maintain stable closed-loop operation across the intended gain and load range.
This product record combines package, electrical, qualification, sourcing, and drop-in comparison information with practical circuit guidance. It is intended to accelerate engineering selection for compact dual-op-amp designs while clearly distinguishing direct replacements from alternatives that require compatibility review.
Alternativas drop-in para LM2904WHYST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2904WHYST (mesmo formato e footprint) — diferindo em Package, Number of Channels, Slew Rate, Input Bias Current, Amplifier Type.
LM2904YDT
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →LM358DT
✅ Drop-In✗ Fora de estoque
$0.0509 / unidade
Ver ficha técnica →TLV6002
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP6002-I/SN
✅ Drop-InConsulte o preço
Ver ficha técnica →RC4558
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2904WHYST Classificações máximas e características elétricas
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 0.6 V/us |
| Input Bias Current | 200 nA |
| Input Offset Voltage | 7 mV |
| Encapsulamento | 8-pin MiniSO |
| Body Width | 3.90 mm |
| Tipo de montagem | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
| Maximum Rated Operating Temperature | 150 C |
| Product Type | Single-ended amplifier circuit |
| Signal Chain Role | General-purpose signal amplification |
Configuração de pinos do LM2904WHYST
| Pino 1 | OUT1 — Output of amplifier channel 1 |
| Pino 2 | IN-1 — Inverting input of amplifier channel 1 |
| Pino 3 | IN+1 — Non-inverting input of amplifier channel 1 |
| Pino 4 | V- — Negative supply or ground connection |
| Pino 5 | IN+2 — Non-inverting input of amplifier channel 2 |
| Pino 6 | IN-2 — Inverting input of amplifier channel 2 |
| Pino 7 | OUT2 — Output of amplifier channel 2 |
| Pino 8 | V+ — Positive supply connection |
Aplicações típicas
LM2904WHYST é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Low-Side Current Sensing, Audio Preamplification, Active Filter and Control Loop, Automotive Control and Monitoring, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM2904WHYST fits low-frequency industrial sensor interfaces because its 200 nA input bias current limits errors when measuring sources with relatively high output impedance. A 1.1 MHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensors, while the 0.6 V/us slew rate supports gradual sensor changes. Both channels can amplify or filter related signals on the same board. The design must keep sensor input voltages inside the amplifier’s common-mode range and verify output swing at the selected supply voltage.
Recomendado
Low-Side Current Sensing
LM2904WHYST can amplify the small voltage developed across a low-side current-sense resistor without introducing a large package-count penalty. Its 200 nA input bias current is valuable when the sense-resistor node has limited source impedance, and the 1.1 MHz bandwidth accommodates many power-conversion control signals. One channel may serve the measurement amplifier while the other provides gain or filtering. Verify common-mode limits during startup, transient response, and operation when the measured node approaches either supply rail.
Recomendado
Audio Preamplification
The LM2904WHYST is appropriate for modest audio preamplifier stages that need two channels and do not require rail-to-rail input or output operation. Its 200 nA input bias current is compatible with many low-impedance audio sources, while the 1.1 MHz gain-bandwidth product is sufficient for voice-band and conventional audio signal paths. Each channel can implement gain and filtering around the amplifier. The circuit should provide adequate supply headroom for the required output swing and be checked for distortion and stability at the selected closed-loop gain.
Recomendado
Active Filter and Control Loop
LM2904WHYST can form the active elements in low-frequency filters and simple analog control loops. A 1.1 MHz gain-bandwidth product leaves useful bandwidth below the device’s unity-gain frequency for common first-order and second-order implementations, and the 0.6 V/us slew rate supports non-abrupt control signals. The two independent channels can implement cascaded stages or complementary functions. Resistor and capacitor tolerances directly determine filter accuracy, while source capacitance and noise gain must be checked to preserve closed-loop stability.
Recomendado
Automotive Control and Monitoring
The LM2904WHYST is identified as AEC-Q100 qualified and rated for operation up to 150 C, supporting its use in automotive monitoring and control electronics when all application limits are satisfied. Its two channels can handle complementary sensor signals or separate monitoring functions in a compact MiniSO-8 package. At elevated temperatures, thermal derating and the documented increase in input bias current must be considered, particularly for high-impedance sources. Production validation should confirm the exact ordering code, qualification conditions, voltage range, and worst-case accuracy.
Recomendado
Portable Instrumentation
LM2904WHYST is suitable for compact instrumentation requiring two general-purpose analog channels without the footprint of larger dual packages. The 200 nA bias current reduces loading on sensor and divider networks, and the 1.1 MHz bandwidth is suitable for many low-bandwidth measurement channels. It can be used for excitation buffering, differential measurement, or gain stages in portable test equipment. Battery operation requires attention to supply range and current consumption, while signal-ground layout must minimize offsets, noise coupling, and errors from shared return paths.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2904WHYST — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2904YDT | LM358 | TLV6002 | MCP6002 | RC4558 |
|---|---|---|---|---|---|---|
| Package | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Microchip Technology | Renesas Electronics |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.5 MHz |
Principais diferenciais
- Higher bandwidth than common LM358-class alternatives (vs LM358)
- Lower input bias current than rail-to-rail alternatives (vs TLV6002)
- Automotive qualification and elevated-temperature capability (vs MCP6002)
- Direct same-family alternative with matching core characteristics (vs LM2904YDT)
Notas de projeto
Place the supply-bypass capacitor directly between pins 8 and 4, with the ground connection kept short and low impedance. Route the input and feedback traces away from switching nodes and high-current paths. Because both channels are independent, each input should have a defined DC path and each feedback network should connect only to its associated output. Keep the exposed package orientation and pin-1 mark aligned with the manufacturer footprint during PCB assembly.
Check the selected noise gain against the 1.1 MHz gain-bandwidth product and the 0.6 V/us slew rate before using the amplifier at high closed-loop gain. Capacitance at the input and output pins can alter poles and phase margin, especially with long PCB traces. Use short feedback paths and consider small isolation resistors where source or load capacitance is unavoidable. Validate the final circuit with the intended signal amplitude, frequency, supply configuration, and external load.
Do not assume that an 8-pin package guarantees operational interchangeability. The input common-mode range, output swing, supply range, input offset, bias current, noise, and slew behavior must remain valid for every operating condition. If a channel is unused, tie its non-inverting input to a valid common-mode potential rather than allowing it to float. For automotive use, verify the exact grade and account for thermal derating and bias-current growth at elevated ambient temperature.
Informações de conformidade
The AEC-Q100 qualification and 150 C operating rating are identified for LM2904WHYST. Other environmental and material-compliance attributes are not specified in the cited product information.