LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics
MPN: LM2904WHYST ✓ 啟用中LM2904WHYST 概覽
An operational amplifier is an analog amplifier that uses very high open-loop gain to compare or amplify a differential input signal. The LM2904 family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, comparator, and rail-to-rail amplifier categories. The LM2904WHYST is intended for applications requiring two amplifiers, moderate bandwidth, low input bias current, and a compact surface-mount footprint rather than precision or high-speed performance.
Key features include two amplifier channels, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 200 nA input bias current, and 7 mV input offset voltage as identified for this device. The MiniSO-8 package reduces board area while retaining separate power, ground, input, and output connections for each channel. The automotive-oriented ordering code also supports use in temperature-qualified equipment, subject to the device's stated operating limits.
Each channel operates as a general-purpose voltage-feedback amplifier, allowing implementation as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style circuit, or active filter. The two independent channels can process separate signals or be combined for differential, instrumentation, and gain-stage arrangements. The 1.1 MHz bandwidth is suitable for low-to-moderate frequency industrial signals, while the 0.6 V/us slew rate supports accurate reproduction of relatively slow input waveforms.
Typical applications include low-side current sensing, industrial sensor interfaces, transducer amplification, audio preamplification, and general control loops. In each case, the low input bias current helps reduce source-loading errors, while the dual configuration can reduce the number of separate amplifier packages required on a board. The amplifier is best suited to signals where moderate bandwidth and common-mode performance are more important than rail-to-rail operation or very low offset.
Designers should verify the input common-mode range, output swing, supply voltage, and stability requirements against the operating conditions before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode voltage. Feedback-network values and source capacitance should be selected to maintain stable closed-loop operation across the intended gain and load range.
This product record combines package, electrical, qualification, sourcing, and drop-in comparison information with practical circuit guidance. It is intended to accelerate engineering selection for compact dual-op-amp designs while clearly distinguishing direct replacements from alternatives that require compatibility review.
直接替換替代品,適用於 LM2904WHYST — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904WHYST (相同外形與佔位) — 差異在於 Package, Number of Channels, Slew Rate, Input Bias Current, Amplifier Type.
LM2904YDT
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM358DT
✅ 直接替換✗ 缺貨
$0.0509 / 單位
查看資料表 →TLV6002
✅ 直接替換📋 參考替代品(不在目錄中)
MCP6002-I/SN
✅ 直接替換聯絡詢價
查看資料表 →RC4558
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904WHYST 最大額定值與電氣特性
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 1.1 MHz |
| Slew Rate | 0.6 V/us |
| Input Bias Current | 200 nA |
| Input Offset Voltage | 7 mV |
| 封裝 | 8-pin MiniSO |
| Body Width | 3.90 mm |
| 安裝類型 | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
| Maximum Rated Operating Temperature | 150 C |
| Product Type | Single-ended amplifier circuit |
| Signal Chain Role | General-purpose signal amplification |
LM2904WHYST 腳位配置
| 腳位 1 | OUT1 — Output of amplifier channel 1 |
| 腳位 2 | IN-1 — Inverting input of amplifier channel 1 |
| 腳位 3 | IN+1 — Non-inverting input of amplifier channel 1 |
| 腳位 4 | V- — Negative supply or ground connection |
| 腳位 5 | IN+2 — Non-inverting input of amplifier channel 2 |
| 腳位 6 | IN-2 — Inverting input of amplifier channel 2 |
| 腳位 7 | OUT2 — Output of amplifier channel 2 |
| 腳位 8 | V+ — Positive supply connection |
典型應用
LM2904WHYST 適用於 6 應用s: Industrial Sensor Signal Conditioning, Low-Side Current Sensing, Audio Preamplification, Active Filter and Control Loop, Automotive Control and Monitoring, Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM2904WHYST fits low-frequency industrial sensor interfaces because its 200 nA input bias current limits errors when measuring sources with relatively high output impedance. A 1.1 MHz gain-bandwidth product provides useful bandwidth for common temperature, pressure, and position sensors, while the 0.6 V/us slew rate supports gradual sensor changes. Both channels can amplify or filter related signals on the same board. The design must keep sensor input voltages inside the amplifier’s common-mode range and verify output swing at the selected supply voltage.
推薦
Low-Side Current Sensing
LM2904WHYST can amplify the small voltage developed across a low-side current-sense resistor without introducing a large package-count penalty. Its 200 nA input bias current is valuable when the sense-resistor node has limited source impedance, and the 1.1 MHz bandwidth accommodates many power-conversion control signals. One channel may serve the measurement amplifier while the other provides gain or filtering. Verify common-mode limits during startup, transient response, and operation when the measured node approaches either supply rail.
推薦
Audio Preamplification
The LM2904WHYST is appropriate for modest audio preamplifier stages that need two channels and do not require rail-to-rail input or output operation. Its 200 nA input bias current is compatible with many low-impedance audio sources, while the 1.1 MHz gain-bandwidth product is sufficient for voice-band and conventional audio signal paths. Each channel can implement gain and filtering around the amplifier. The circuit should provide adequate supply headroom for the required output swing and be checked for distortion and stability at the selected closed-loop gain.
推薦
Active Filter and Control Loop
LM2904WHYST can form the active elements in low-frequency filters and simple analog control loops. A 1.1 MHz gain-bandwidth product leaves useful bandwidth below the device’s unity-gain frequency for common first-order and second-order implementations, and the 0.6 V/us slew rate supports non-abrupt control signals. The two independent channels can implement cascaded stages or complementary functions. Resistor and capacitor tolerances directly determine filter accuracy, while source capacitance and noise gain must be checked to preserve closed-loop stability.
推薦
Automotive Control and Monitoring
The LM2904WHYST is identified as AEC-Q100 qualified and rated for operation up to 150 C, supporting its use in automotive monitoring and control electronics when all application limits are satisfied. Its two channels can handle complementary sensor signals or separate monitoring functions in a compact MiniSO-8 package. At elevated temperatures, thermal derating and the documented increase in input bias current must be considered, particularly for high-impedance sources. Production validation should confirm the exact ordering code, qualification conditions, voltage range, and worst-case accuracy.
推薦
Portable Instrumentation
LM2904WHYST is suitable for compact instrumentation requiring two general-purpose analog channels without the footprint of larger dual packages. The 200 nA bias current reduces loading on sensor and divider networks, and the 1.1 MHz bandwidth is suitable for many low-bandwidth measurement channels. It can be used for excitation buffering, differential measurement, or gain stages in portable test equipment. Battery operation requires attention to supply range and current consumption, while signal-ground layout must minimize offsets, noise coupling, and errors from shared return paths.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904WHYST — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904YDT | LM358 | TLV6002 | MCP6002 | RC4558 |
|---|---|---|---|---|---|---|
| Package | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO | 8-pin MiniSO |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Microchip Technology | Renesas Electronics |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Gain-Bandwidth Product | 1.1 MHz | 1.1 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.0 MHz | Approximately 1.5 MHz |
主要差異化特點
- Higher bandwidth than common LM358-class alternatives (對比LM358)
- Lower input bias current than rail-to-rail alternatives (對比TLV6002)
- Automotive qualification and elevated-temperature capability (對比MCP6002)
- Direct same-family alternative with matching core characteristics (對比LM2904YDT)
設計說明
Place the supply-bypass capacitor directly between pins 8 and 4, with the ground connection kept short and low impedance. Route the input and feedback traces away from switching nodes and high-current paths. Because both channels are independent, each input should have a defined DC path and each feedback network should connect only to its associated output. Keep the exposed package orientation and pin-1 mark aligned with the manufacturer footprint during PCB assembly.
Check the selected noise gain against the 1.1 MHz gain-bandwidth product and the 0.6 V/us slew rate before using the amplifier at high closed-loop gain. Capacitance at the input and output pins can alter poles and phase margin, especially with long PCB traces. Use short feedback paths and consider small isolation resistors where source or load capacitance is unavoidable. Validate the final circuit with the intended signal amplitude, frequency, supply configuration, and external load.
Do not assume that an 8-pin package guarantees operational interchangeability. The input common-mode range, output swing, supply range, input offset, bias current, noise, and slew behavior must remain valid for every operating condition. If a channel is unused, tie its non-inverting input to a valid common-mode potential rather than allowing it to float. For automotive use, verify the exact grade and account for thermal derating and bias-current growth at elevated ambient temperature.
合規資訊
The AEC-Q100 qualification and 150 C operating rating are identified for LM2904WHYST. Other environmental and material-compliance attributes are not specified in the cited product information.