MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI
MPN: MAX3243MDBREP ✓ सक्रियMAX3243MDBREP अवलोकन
An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or peripheral into RS-232-compatible line levels and converts received line-level signals back into digital logic. The MAX3243 belongs to the interface IC, communications transceiver, and RS-232 line-driver/receiver hierarchy. Its multichannel arrangement supports equipment that requires several data lines but not a full nine-line desktop serial port.
The MAX3243 operates from a single 3 V to 5.5 V supply, allowing operation from 3.3 V and 5 V systems. Its 250 kbps data rate is suitable for asynchronous serial links whose required baud rate remains below that operating limit. Pin-to-pin ESD protection of ±15 kV applies to the serial-port connection pins, including ground, according to the Texas Instruments MAX3243 datasheet.
Internally, the MAX3243 combines three drivers, five receivers, and a dual charge-pump circuit. The charge pump generates the positive and negative voltage rails needed by the line drivers while allowing operation from a low-voltage single supply. The interface meets the electrical requirements of TIA/EIA-232-F and is intended to sit between an asynchronous communication controller and a serial-port connector.
Typical uses include industrial control equipment, instrumentation, data acquisition systems, point-of-sale terminals, and embedded serial interfaces. The three transmitters and five receivers make the device useful for designs combining several command, status, and data paths while keeping the external power supply simple. The enhanced-product ordering option is suited to applications requiring the military temperature range and enhanced environmental screening.
Layout is critical because RS-232 driver outputs carry high-voltage transitions, while receiver inputs are sensitive to electrical noise. Keep charge-pump and receiver-capacitor connections short, provide a solid ground reference, and route serial traces away from clocks, switching nodes, and high-current return paths. Confirm that the selected external capacitors satisfy the datasheet recommendations and that connector-side protection is coordinated with the IC's ±15 kV HBM rating.
This product guide combines the manufacturer's electrical specifications, ordering information, package details, and practical RS-232 design guidance. It also identifies the verified pin-compatible MAX3243IDBR option while clearly separating package, temperature, and qualification differences that must be reviewed before design substitution.
के लिए ड्रॉप-इन विकल्प MAX3243MDBREP — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MAX3243MDBREP (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Product Type, Supply Voltage Range.
MAX3243IDBR
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MAX3243MDBREP विशेषताएं
| Product Type | Multichannel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Line Drivers | 3 |
| Line Receivers | 5 |
| Charge-Pump Circuits | 2 |
| ESD Protection | ±15 kV HBM |
| ऑपरेटिंग तापमान रेंज | -55 °C to +125 °C |
| पैकेज | 28-pin SSOP |
| Terminal Count | 28 |
| माउंटिंग प्रकार | Surface mount |
| Package Shape | Rectangular gull-wing |
| RS-232 Standard Compliance | TIA/EIA-232-F |
| Interface Function | Electrical interface between an asynchronous communication controller and a serial-port connector |
| Logic Supply | Single 3 V to 5.5 V supply |
MAX3243MDBREP rectangular gull-wing पिन कॉन्फ़िगरेशन गाइड
MAX3243MDBREP (rectangular gull-wing पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MAX3243MDBREP.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
MAX3243MDBREP के लिए उपयुक्त है 6 अनुप्रयोगs: Industrial Control Systems, Data Acquisition and Instrumentation, Embedded Serial Interfaces, Security and Access Equipment, Point-of-Sale Terminals, Communication Port Expansion.
Industrial Control Systems
The MAX3243MDBREP is well suited to industrial controllers that exchange command, status, and sensor data over RS-232. Its three line drivers and five receivers support multiple channels from one 3 V to 5.5 V supply, while the 250 kbps rate covers many asynchronous control protocols. The -55 °C to +125 °C operating range is useful in equipment exposed to wide temperature conditions. Place the transceiver between the controller UART and a protected connector, and route charge-pump and receiver paths away from switching nodes.
अनुशंसित
Data Acquisition and Instrumentation
The MAX3243MDBREP can connect laboratory and process instruments that use several RS-232 signals but do not require a complete desktop serial-port implementation. Three transmitter channels and five receiver channels provide asymmetric connectivity for commands, measurements, acknowledgments, and status flags. Operation from 3.3 V or 5 V systems reduces supply complexity, while 250 kbps operation supports many measurement-control protocols. Use a solid analog ground and shielded cable, and confirm the selected baud rate against cable length and capacitive loading.
अनुशंसित
Embedded Serial Interfaces
The MAX3243MDBREP provides a compact interface between an embedded asynchronous controller and an RS-232 port. A single 3 V to 5.5 V supply supports both the logic-side environment and the charge-pump circuitry, while the three drivers can carry outgoing commands or status signals. The five receivers can monitor incoming data and handshake lines. At 250 kbps maximum rate, the device accommodates many embedded protocols. Confirm the UART's signal levels, inversion requirements, and flow-control timing against the family datasheet.
अनुशंसित
Security and Access Equipment
The MAX3243MDBREP can interface access-control, alarm, and security equipment that uses several RS-232 control lines. The multiple receivers support incoming sensor states, acknowledgments, and fault signals, while the three drivers support outbound commands. Its ±15 kV HBM protection on the serial-port connection pins adds a useful board-level defense where cables are present. The 250 kbps rate is suitable for common configuration and status protocols. Connector selection, ground bonding, and external surge protection remain important parts of a robust interface.
अनुशंसित
Point-of-Sale Terminals
The MAX3243MDBREP is appropriate for point-of-sale peripherals that need a compact RS-232 interface for receipt printers, scales, customer displays, or service terminals. Three drivers and five receivers permit several control and status paths without requiring three separate transceivers. Its 3 V to 5.5 V supply range allows use with common embedded systems, and the 250 kbps limit suits typical peripheral data rates. Keep the connector and logic sections separated by a clear ground strategy to reduce noise coupling in compact equipment.
अनुशंसित
Communication Port Expansion
The MAX3243MDBREP can add RS-232 connectivity to a controller that has limited serial resources. Its three drivers and five receivers enable asymmetric port expansion for command, response, and status lines while retaining a simple single-supply design. The device operates up to 250 kbps and provides ±15 kV HBM protection on serial connection pins, including ground. When expanding ports, maintain consistent logic levels across the system and verify that the additional lines do not exceed the host controller's pin or timing constraints.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MAX3243MDBREP — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MAX3243IDBR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 28-pin SSOP | 28-pin SSOP |
| Product Type | Multichannel RS-232 line driver and receiver | Multichannel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps |
| Line Drivers | 3 | 3 |
| Line Receivers | 5 | 5 |
| Operating Temperature Range | -55 °C to +125 °C | -40 °C to +85 °C |
| ESD Protection | ±15 kV HBM | ±15 kV HBM |
मुख्य विशेषताएँ
- Broader operating-temperature capability (बनामMAX3243IDBR)
- Same compact channel integration (बनामMAX3243IDBR)
- High-speed multichannel RS-232 operation (बनामMAX3243IDBR)
डिज़ाइन नोट्स
Keep the charge-pump capacitor connections and receiver input traces short. Place the required capacitors close to their associated pins and use a continuous ground plane under and around the interface section. Route connector-side RS-232 traces away from clocks, switching converters, motor drive nodes, and other high-dV/dt circuitry to minimize common-mode and capacitive coupling.
Do not treat ±15 kV HBM ESD protection as a complete surge-protection solution. The HBM rating applies to the specified serial-port pins under the defined test conditions, while cable-borne transients can exceed that level. Use a suitable connector, chassis grounding, and coordinated external protection when the port is exposed to severe industrial or outdoor transients.
Decouple the single 3 V to 5.5 V supply near the device with the capacitance specified in the manufacturer datasheet. The charge pumps generate the positive and negative voltages used by the line drivers, so unstable supply voltage or inadequate local decoupling can disturb driver output levels. Check source impedance, capacitor voltage rating, and startup behavior across the complete temperature range.
Treat the RS-232 interface as a physically robust but electrically slow communication path. Verify the UART baud rate against the transceiver's 250 kbps maximum, account for cable capacitance and propagation delay, and avoid excessive edge rates on external interconnects. Receiver and driver ground references should connect according to the recommended interface layout in the MAX3243 datasheet.
अनुपालन जानकारी
The MAX3243 family documentation identifies TIA/EIA-232-F compliance and ±15 kV HBM ESD protection. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for this ordering code require confirmation in the manufacturer product documentation.