MAX3243MDBREP - 3V/5.5V 250kbps RS-232 Transceiver | TI
料号: MAX3243MDBREP ✓ 量产中MAX3243MDBREP 概述
An RS-232 transceiver is an interface IC that converts logic-level signals from a host, controller, or peripheral into RS-232-compatible line levels and converts received line-level signals back into digital logic. The MAX3243 belongs to the interface IC, communications transceiver, and RS-232 line-driver/receiver hierarchy. Its multichannel arrangement supports equipment that requires several data lines but not a full nine-line desktop serial port.
The MAX3243 operates from a single 3 V to 5.5 V supply, allowing operation from 3.3 V and 5 V systems. Its 250 kbps data rate is suitable for asynchronous serial links whose required baud rate remains below that operating limit. Pin-to-pin ESD protection of ±15 kV applies to the serial-port connection pins, including ground, according to the Texas Instruments MAX3243 datasheet.
Internally, the MAX3243 combines three drivers, five receivers, and a dual charge-pump circuit. The charge pump generates the positive and negative voltage rails needed by the line drivers while allowing operation from a low-voltage single supply. The interface meets the electrical requirements of TIA/EIA-232-F and is intended to sit between an asynchronous communication controller and a serial-port connector.
Typical uses include industrial control equipment, instrumentation, data acquisition systems, point-of-sale terminals, and embedded serial interfaces. The three transmitters and five receivers make the device useful for designs combining several command, status, and data paths while keeping the external power supply simple. The enhanced-product ordering option is suited to applications requiring the military temperature range and enhanced environmental screening.
Layout is critical because RS-232 driver outputs carry high-voltage transitions, while receiver inputs are sensitive to electrical noise. Keep charge-pump and receiver-capacitor connections short, provide a solid ground reference, and route serial traces away from clocks, switching nodes, and high-current return paths. Confirm that the selected external capacitors satisfy the datasheet recommendations and that connector-side protection is coordinated with the IC's ±15 kV HBM rating.
This product guide combines the manufacturer's electrical specifications, ordering information, package details, and practical RS-232 design guidance. It also identifies the verified pin-compatible MAX3243IDBR option while clearly separating package, temperature, and qualification differences that must be reviewed before design substitution.
直接替换替代料: MAX3243MDBREP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX3243MDBREP (相同外形与封装尺寸) ——差异在于 Package, Product Type, Supply Voltage Range.
MAX3243IDBR
✅ 直接替换联系询价
查看数据手册 →MAX3243MDBREP 规格参数
| Product Type | Multichannel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| Line Drivers | 3 |
| Line Receivers | 5 |
| Charge-Pump Circuits | 2 |
| ESD Protection | ±15 kV HBM |
| 工作温度范围 | -55 °C to +125 °C |
| 封装 | 28-pin SSOP |
| Terminal Count | 28 |
| 安装类型 | Surface mount |
| Package Shape | Rectangular gull-wing |
| RS-232 Standard Compliance | TIA/EIA-232-F |
| Interface Function | Electrical interface between an asynchronous communication controller and a serial-port connector |
| Logic Supply | Single 3 V to 5.5 V supply |
MAX3243MDBREP rectangular gull-wing 引脚配置指南
MAX3243MDBREP(rectangular gull-wing 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3243MDBREP.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3243MDBREP 适用于 6 应用s: Industrial Control Systems, Data Acquisition and Instrumentation, Embedded Serial Interfaces, Security and Access Equipment, Point-of-Sale Terminals, Communication Port Expansion.
Industrial Control Systems
The MAX3243MDBREP is well suited to industrial controllers that exchange command, status, and sensor data over RS-232. Its three line drivers and five receivers support multiple channels from one 3 V to 5.5 V supply, while the 250 kbps rate covers many asynchronous control protocols. The -55 °C to +125 °C operating range is useful in equipment exposed to wide temperature conditions. Place the transceiver between the controller UART and a protected connector, and route charge-pump and receiver paths away from switching nodes.
推荐
Data Acquisition and Instrumentation
The MAX3243MDBREP can connect laboratory and process instruments that use several RS-232 signals but do not require a complete desktop serial-port implementation. Three transmitter channels and five receiver channels provide asymmetric connectivity for commands, measurements, acknowledgments, and status flags. Operation from 3.3 V or 5 V systems reduces supply complexity, while 250 kbps operation supports many measurement-control protocols. Use a solid analog ground and shielded cable, and confirm the selected baud rate against cable length and capacitive loading.
推荐
Embedded Serial Interfaces
The MAX3243MDBREP provides a compact interface between an embedded asynchronous controller and an RS-232 port. A single 3 V to 5.5 V supply supports both the logic-side environment and the charge-pump circuitry, while the three drivers can carry outgoing commands or status signals. The five receivers can monitor incoming data and handshake lines. At 250 kbps maximum rate, the device accommodates many embedded protocols. Confirm the UART's signal levels, inversion requirements, and flow-control timing against the family datasheet.
推荐
Security and Access Equipment
The MAX3243MDBREP can interface access-control, alarm, and security equipment that uses several RS-232 control lines. The multiple receivers support incoming sensor states, acknowledgments, and fault signals, while the three drivers support outbound commands. Its ±15 kV HBM protection on the serial-port connection pins adds a useful board-level defense where cables are present. The 250 kbps rate is suitable for common configuration and status protocols. Connector selection, ground bonding, and external surge protection remain important parts of a robust interface.
推荐
Point-of-Sale Terminals
The MAX3243MDBREP is appropriate for point-of-sale peripherals that need a compact RS-232 interface for receipt printers, scales, customer displays, or service terminals. Three drivers and five receivers permit several control and status paths without requiring three separate transceivers. Its 3 V to 5.5 V supply range allows use with common embedded systems, and the 250 kbps limit suits typical peripheral data rates. Keep the connector and logic sections separated by a clear ground strategy to reduce noise coupling in compact equipment.
推荐
Communication Port Expansion
The MAX3243MDBREP can add RS-232 connectivity to a controller that has limited serial resources. Its three drivers and five receivers enable asymmetric port expansion for command, response, and status lines while retaining a simple single-supply design. The device operates up to 250 kbps and provides ±15 kV HBM protection on serial connection pins, including ground. When expanding ports, maintain consistent logic levels across the system and verify that the additional lines do not exceed the host controller's pin or timing constraints.
推荐
推荐产品汇总
工程参考数据: MAX3243MDBREP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX3243IDBR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 28-pin SSOP | 28-pin SSOP |
| Product Type | Multichannel RS-232 line driver and receiver | Multichannel RS-232 line driver and receiver |
| Supply Voltage Range | 3 V to 5.5 V | 3 V to 5.5 V |
| Maximum Data Rate | 250 kbps | 250 kbps |
| Line Drivers | 3 | 3 |
| Line Receivers | 5 | 5 |
| Operating Temperature Range | -55 °C to +125 °C | -40 °C to +85 °C |
| ESD Protection | ±15 kV HBM | ±15 kV HBM |
关键差异点
- Broader operating-temperature capability (对比 MAX3243IDBR)
- Same compact channel integration (对比 MAX3243IDBR)
- High-speed multichannel RS-232 operation (对比 MAX3243IDBR)
设计说明
Keep the charge-pump capacitor connections and receiver input traces short. Place the required capacitors close to their associated pins and use a continuous ground plane under and around the interface section. Route connector-side RS-232 traces away from clocks, switching converters, motor drive nodes, and other high-dV/dt circuitry to minimize common-mode and capacitive coupling.
Do not treat ±15 kV HBM ESD protection as a complete surge-protection solution. The HBM rating applies to the specified serial-port pins under the defined test conditions, while cable-borne transients can exceed that level. Use a suitable connector, chassis grounding, and coordinated external protection when the port is exposed to severe industrial or outdoor transients.
Decouple the single 3 V to 5.5 V supply near the device with the capacitance specified in the manufacturer datasheet. The charge pumps generate the positive and negative voltages used by the line drivers, so unstable supply voltage or inadequate local decoupling can disturb driver output levels. Check source impedance, capacitor voltage rating, and startup behavior across the complete temperature range.
Treat the RS-232 interface as a physically robust but electrically slow communication path. Verify the UART baud rate against the transceiver's 250 kbps maximum, account for cable capacitance and propagation delay, and avoid excessive edge rates on external interconnects. Receiver and driver ground references should connect according to the recommended interface layout in the MAX3243 datasheet.
合规信息
The MAX3243 family documentation identifies TIA/EIA-232-F compliance and ±15 kV HBM ESD protection. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations for this ordering code require confirmation in the manufacturer product documentation.