MC33179PG - 5 MHz Quad Low-Power Op Amp | onsemi
MPN: MC33179PG ✓ सक्रियMC33179PG अवलोकन
An operational amplifier is an analog building block that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The MC33179PG belongs to the operational-amplifier hierarchy, where a general-purpose quad amplifier provides four independent amplifiers in one package. Placing four amplifiers in a single 14-pin DIP reduces component count and simplifies PCB assembly in designs that require several matched signal-conditioning channels.
Key features include a 5 MHz gain-bandwidth product, a 2 V to 18 V operating supply range, and low-noise bipolar input characteristics. The quad configuration permits four independent amplifier sections with a shared positive and negative supply. This makes the MC33179PG appropriate for audio mixer stages, active low-pass and band-pass filters, sensor-conditioning circuits, and small-signal buffers. Its through-hole package also remains convenient for prototypes, educational designs, repair work, and manually assembled industrial control boards.
The MC33179 family uses high-frequency PNP input transistors to obtain a combination of low noise and improved transient response compared with conventional bipolar amplifier inputs. This architecture is useful when a design must recover small signals cleanly while remaining within a modest power budget. Because the amplifiers share package leads for supply voltage, the board layout should treat the power pins as high-current nodes and provide a low-impedance return path to the decoupling capacitors.
Typical applications include four-channel audio preamplification, active crossover and equalization networks, instrumentation amplifiers built from discrete sections, sensor signal conditioning, and general-purpose industrial control interfaces. The 14-pin DIP footprint is especially useful where through-hole assembly is preferred over fine-pitch surface-mount assembly. Designers should verify noise, offset, bias-current, output-swing, and stability requirements against the actual signal amplitude and source impedance.
When laying out the MC33179PG, place the supply bypass capacitor close to pins 4 and 11 and route the ground return directly to the device ground pin. Keep feedback-loop components compact to minimize parasitic capacitance and oscillation risk, especially when the closed-loop gain is high. Decouple each signal source locally where practical so that input and output currents do not share long current paths on the board.
This page consolidates the MC33179PG electrical identity, verified package and sourcing details, drop-in replacement analysis, and practical analog-layout guidance. It is intended to help engineers move quickly from device selection to schematic capture, PCB layout, and legacy-board redesign while remaining mindful of the part's through-hole package and amplifier-level trade-offs.
के लिए ड्रॉप-इन विकल्प MC33179PG — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MC33179PG (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Number of Pins, Package.
MC33178PG
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TL054CN
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
MC33179PG Maximum Ratings और Electrical Characteristics
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifier Channels | 4 channels |
| Gain-Bandwidth Product | 5 MHz |
| Supply Voltage Range | 2 V to 18 V |
| पैकेज | 14-PDIP, 0.300 in (7.62 mm) pitch |
| माउंटिंग प्रकार | Through-hole |
| Input Transistor Technology | Bipolar with high-frequency PNP input transistors |
| Operating Temperature Class | Industrial temperature range |
| पिन की संख्या | 14 pins |
| लाइफसाइकिल स्थिति | Active product listing |
MC33179PG पिन कॉन्फ़िगरेशन
| पिन 1 | OUTA — Amplifier A output |
| पिन 2 | -INA — Amplifier A inverting input |
| पिन 3 | +INA — Amplifier A non-inverting input |
| पिन 4 | V- — Negative supply voltage |
| पिन 5 | +INB — Amplifier B non-inverting input |
| पिन 6 | -INB — Amplifier B inverting input |
| पिन 7 | OUTB — Amplifier B output |
| पिन 8 | OUTC — Amplifier C output |
| पिन 9 | -INC — Amplifier C inverting input |
| पिन 10 | +INC — Amplifier C non-inverting input |
| पिन 11 | V+ — Positive supply voltage |
| पिन 12 | +IND — Amplifier D non-inverting input |
| पिन 13 | -IND — Amplifier D inverting input |
| पिन 14 | OUTD — Amplifier D output |
सामान्य अनुप्रयोग
MC33179PG के लिए उपयुक्त है 6 अनुप्रयोगs: Four-Channel Audio Preamplification, Active Audio Equalization and Crossover Filters, Industrial Sensor Signal Conditioning, Active Notch and Band-Pass Filtering, Control-Signal Buffering and Level Shifting, Audio Equipment Repair and Legacy Retrofit.
Four-Channel Audio Preamplification
The MC33179PG fits four-channel audio preamplification because it places four independent bipolar amplifiers in one 14-PDIP package while providing a 5 MHz gain-bandwidth product. Each channel can amplify a low-level source before a volume control, mixer, or line-level stage. The shared 2 V to 18 V supply simplifies power distribution, although each amplifier still requires local input and feedback components. For low-impedance microphone or instrument sources, check the input bias current in the manufacturer datasheet against the source impedance, because high source resistance can shift the DC operating point. Keep input traces short and place the supply bypass capacitor close to pins 4 and 11.
अनुशंसित
Active Audio Equalization and Crossover Filters
The MC33179PG is well suited to active equalization and crossover networks that require several filtered amplifier channels in one board. Its 5 MHz gain-bandwidth product provides useful loop gain for moderate-frequency audio filters, while four independent sections allow stereo low-pass and high-pass stages to share a package. Use the manufacturer application circuits as the starting point for stable feedback arrangements, especially where Q factor and phase margin are critical. Component tolerances determine the actual filter response, so evaluate R and C networks with their actual tolerances. Keep each filter's input node away from the shared supply pins to minimize channel-to-channel crosstalk.
अनुशंसित
Industrial Sensor Signal Conditioning
The MC33179PG can condition four low-level industrial sensor signals when the system needs local amplification before an analog-to-digital converter. Its industrial-temperature rating and 2 V to 18 V supply range fit many 5 V, 12 V, and 15 V control rails. Each channel can buffer a transducer or amplify a bridge-derived voltage, then drive a short trace into the next conversion stage. Verify common-mode input range and output swing for the selected supply because those values are not interchangeable with gain-bandwidth. For high-impedance sensors, examine bias-current-induced offset, and use a dedicated low-noise reference at the ADC rather than treating the op amp as a precision voltage reference.
अनुशंसित
Active Notch and Band-Pass Filtering
The MC33179PG supports active notch, band-pass, and frequency-selective stages where four independent channels reduce the number of packages needed. The device's 5 MHz gain-bandwidth product is well above the center frequencies of many audio, communications, and measurement filters, allowing meaningful closed-loop gain while preserving stability margins. Select resistor and capacitor networks using the manufacturer's application guidance, then check stability with source and load impedances that match the finished circuit. Place the four amplifier sections so their feedback loops do not surround shared supply or ground paths, because long loops can pick up noise and create unintended coupling.
अनुशंसित
Control-Signal Buffering and Level Shifting
The MC33179PG can buffer four low-current control signals or provide limited level shifting between compatible analog stages in an industrial controller. The quad topology allows outputs to drive successive circuit blocks without repeating a package for every channel, and the 2 V to 18 V supply range supports common control-rail choices. Verify the output swing, output-current capability, and input common-mode range before assigning the amplifier to a relay-control or actuator-interface stage. Keep the buffer inputs close to their source components and give each output a defined return path. Decouple the shared supply pins once at the package, and route output currents away from the sensitive input-reference ground.
अनुशंसित
Audio Equipment Repair and Legacy Retrofit
The MC33179PG's 14-PDIP through-hole package is useful for repairing or modernizing legacy audio and control equipment that uses discrete or obsolete quad amplifier stages. A DIP outline is straightforward to install on a repair board with a conventional through-hole footprint and allows individual socketed or soldered replacement. Before substituting it into vintage equipment, compare the original amplifier's gain-bandwidth, noise voltage, input bias current, output swing, and supply pins against the MC33179PG datasheet. Retrofitting a PCB that uses a surface-mount footprint would require an adapter and is not a direct footprint replacement.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MC33179PG — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MC33178PG | TL054CN |
|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments |
| Package | 14-PDIP (0.300", 7.62mm) | 14-PDIP (0.300", 7.62mm) - same | 14-PDIP (0.300", 7.62mm) - same |
| Amplifier Channels | 4 circuits | 4 circuits | 4 circuits |
| Mounting Type | Through-hole | Through-hole | Through-hole |
मुख्य विशेषताएँ
- Higher bandwidth than the TL054CN alternative (बनामTL054CN)
- Faster transient response (बनामTL054CN)
- Four independent amplifiers in a through-hole package (बनामMC33178PG)
डिज़ाइन नोट्स
Place the supply bypass capacitor immediately adjacent to pins 4 and 11, with its ground terminal returning directly to the pin 4 ground path. Because all four amplifier sections share the same package supply leads, a long supply trace can couple output-current disturbances into the other channels. Keep each amplifier's feedback components close to its pins and route input nodes away from pins 11 and 12.
Do not treat a same-package amplifier as electrically identical to the MC33179PG. The MC33179PG has a stated input bias current of 100 nA and 2 V/us slew rate, while the TL054CN comparison lists 200 pA bias current and 1.3 V/us slew rate. These differences can alter DC accuracy and transient behavior. Recheck source-impedance errors, feedback bandwidth, output swing, and stability after any substitution.
Keep input and feedback traces short, and avoid routing them beneath or beside the shared positive-supply lead. Place the bypass capacitor where it can supply transient current without sharing a narrow trace with the input reference. For audio or measurement channels with meaningful source impedance, consider guarding between amplifier sections so high-impedance inputs do not collect leakage or injected noise from neighboring channels.
Confirm the operating supply voltage against the input common-mode range and output-swing limits in the manufacturer datasheet. A 2 V to 18 V rating identifies the permitted supply span, but it does not mean every output waveform is usable at the minimum rail. Check quiescent current and channel dissipation under the intended load before assigning the DIP device to a thermally enclosed control board.
अनुपालन जानकारी
The device is described as an industrial-temperature, 14-PDIP operational amplifier. Specific RoHS, REACH, halogen-free, and conflict-minerals declarations are not stated in the product information and are therefore recorded as unknown.