MCP601T-E/SN - 2.8MHz R-R Op Amp | Microchip Technology
MPN: MCP601T-E/SN ✓ सक्रियMCP601T-E/SN अवलोकन
An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to set its closed-loop behavior. The MCP601 belongs to the broader hierarchy of analog amplifiers, amplifier ICs, and semiconductor signal-conditioning devices. Its CMOS implementation emphasizes low bias current, low operating current, high open-loop gain, and rail-to-rail output capability, making it suitable for portable and low-voltage signal-processing systems.
Three defining characteristics are its 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. Rail-to-rail output swing allows the output voltage to approach the supply rails under suitable load conditions. Common-mode input operation below ground is valuable in single-supply circuits that process small signals centered around ground. Unity-gain stability supports direct use as a voltage follower when configured with its output connected to its inverting input.
The MCP601 uses Microchip’s advanced CMOS technology. This architecture provides low bias current, which is important when the amplifier must sense signals from high-impedance sources without loading them aggressively. Its 2.8 MHz gain-bandwidth product provides more bandwidth than many low-power general-purpose amplifiers, while the 230 uA typical operating current supports designs where supply consumption is an important constraint. Rail-to-rail output swing improves usable output range on low-voltage rails.
Typical applications include sensor-signal conditioning, portable instrumentation, battery-powered measurement systems, audio preamplification, and low-voltage analog signal chains. The device is also useful as a buffer or active filter when the selected feedback network keeps the closed-loop gain and bandwidth within stable operating limits. Because its input range can extend below ground, it can simplify signal conditioning around a zero-volt reference.
When designing around the MCP601T-E/SN, use the manufacturer’s recommended bypass-capacitor and stability guidance, place input and output networks close to the device, and verify output settling for the intended closed-loop gain. Designers should also check noise, offset, input-bias-current, and capacitive-loading behavior against the specific signal source rather than relying only on nominal gain-bandwidth figures.
This product page combines the manufacturer specifications with engineering-focused selection guidance, drop-in replacement information, application context, and practical PCB design notes. It also distinguishes temperature-grade and packaging variants within the MCP601 family so engineers can assess PCB reuse and production interchangeability before committing to a source.
के लिए ड्रॉप-इन विकल्प MCP601T-E/SN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं MCP601T-E/SN (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Package, Gain-Bandwidth Product, Product Type, Typical Operating Current, Maximum Supply Voltage.
MCP601T-I/SN
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MCP601-E/SN
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →MCP601T-I/ST
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →MCP601T-E/SN Maximum Ratings और Electrical Characteristics
| Product Type | Single operational amplifier |
| Amplifier Configuration | 1 circuit |
| Technology | CMOS |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Offset Voltage | <2 mV |
| Output Swing | Rail-to-rail |
| Common-Mode Input | Includes input below ground |
| Closed-Loop Gain Stability | Unity gain stable |
| पैकेज | 8-pin SOIC |
| माउंटिंग प्रकार | Surface mount |
| Shipping Format | Tape and reel |
MCP601T-E/SN 8-pin soic पिन कॉन्फ़िगरेशन गाइड
MCP601T-E/SN (8-pin soic पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: MCP601T-E/SN.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
MCP601T-E/SN के लिए उपयुक्त है 6 अनुप्रयोगs: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Low-Voltage Audio Preamplifier, Industrial Current and Voltage Buffering, Active Analog Filtering, Portable Test and Measurement Front End.
Portable Sensor Signal Conditioning
The MCP601T-E/SN is appropriate for conditioning signals from low-power sensors in portable measurement systems. Its 230 uA typical operating current limits amplifier contribution to total supply consumption, while the 2.8 MHz gain-bandwidth product provides useful bandwidth for sensor and instrumentation signals. A non-inverting or differential input stage can use the amplifier’s input and output ratings, provided the selected gain remains stable. Check input bias current against the sensor impedance and confirm that signal amplitudes remain inside the common-mode range.
अनुशंसित
Battery-Powered Data Acquisition
A battery-powered data-acquisition front end benefits from the MCP601T-E/SN because it operates from a single 2.7 V to 5.5 V supply and has 230 uA typical operating current. Rail-to-rail output swing increases the usable signal range in compact systems, particularly when the supply voltage is close to the sensor output span. The amplifier can buffer inputs or implement active filtering, but the engineer must verify offset, bias-current effects, noise, and closed-loop stability across the expected signal bandwidth.
अनुशंसित
Low-Voltage Audio Preamplifier
The MCP601T-E/SN can serve as a low-voltage audio preamplifier stage when the required bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Rail-to-rail output allows the stage to approach the available supply swing, while operation from supplies as low as 2.7 V supports compact audio systems. The design should account for input bias current, output drive into the next stage, noise performance, and the maximum capacitive load. Feedback-component selection must preserve stability at the selected closed-loop gain.
अनुशंसित
Industrial Current and Voltage Buffering
The MCP601T-E/SN can buffer high-impedance voltage sources in industrial measurement systems where a low 230 uA typical operating current is useful. Its common-mode input capability extends below ground, allowing it to process signals centered around a zero-volt reference in single-supply systems. Use it as a voltage follower when the source cannot drive the measurement chain directly. Verify the source impedance against input bias current, provide appropriate bypassing, and keep feedback routing short to reduce sensitivity to noise and capacitive loading.
अनुशंसित
Active Analog Filtering
The MCP601T-E/SN is usable in first-order and higher-order active-filter networks when the closed-loop bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Single-supply operation from 2.7 V to 5.5 V simplifies filtering around a midpoint reference, and rail-to-rail output helps preserve signal amplitude near the supply limits. Exact resistor and capacitor values must be calculated from the desired cutoff, gain, and Q. Confirm noise, offset, and stability across temperature before using the stage for precision measurements.
अनुशंसित
Portable Test and Measurement Front End
The MCP601T-E/SN can form the input amplifier of a portable test-and-measurement instrument when low power and compact single-supply operation are priorities. Its 2.8 MHz gain-bandwidth product supports a broader range of low-frequency and modest intermediate-frequency measurements than a very slow precision amplifier. Use the rail-to-rail output range to maximize signal span, while selecting resistor networks for low offset and appropriate bias-current behavior. Add supply bypassing near the device and verify that source capacitance does not impair settling or stability.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा MCP601T-E/SN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | MCP601T-I/SN | MCP601-E/SN | MCP601T-I/ST |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier | Single amplifier |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Typical Offset Voltage | <2 mV | <2 mV | <2 mV | <2 mV |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Code | T tape-and-reel format | T tape-and-reel format | SN format | ST format |
| Temperature Grade | E grade | I grade | E grade | I grade |
मुख्य विशेषताएँ
- Higher bandwidth than a basic low-power amplifier (बनामLower-bandwidth general-purpose CMOS op amps)
- Useful output range in compact single-supply systems (बनामNon-rail-to-rail input amplifiers)
- Direct family reuse across environmental grades (बनामMCP601T-E/SN)
डिज़ाइन नोट्स
Place the supply bypass capacitor close to the positive and ground pins, and keep the feedback loop compact around the amplifier. A short output route reduces susceptibility to capacitive loading and parasitic feedback. Connect the exposed analog signal paths away from digital clock and switching nodes to preserve the benefit of the low-noise operating characteristics.
Do not select the amplifier from gain-bandwidth product alone. Check closed-loop stability, input and output common-mode limits, load current, output swing, and source impedance. A 2.8 MHz gain-bandwidth product is useful for bandwidth planning, but the usable signal bandwidth depends on noise gain and the feedback network implemented on the PCB.
For high-impedance sensors, calculate the bias-current-induced error before selecting feedback and source resistors. Reduce resistance when bias current dominates, and use shielding or guarded routing when leakage and surface contamination are significant. For precision offset-sensitive circuits, use matched resistor networks and account for the less-than-2 mV typical offset specification in the error budget.
Single-supply operation simplifies routing, but every signal referenced above ground must remain inside the amplifier’s common-mode range and every output must remain inside its output-swing capability. Verify these limits at the lowest supply voltage, highest temperature, and heaviest load because the practical output range is narrower than an ideal rail-to-rail model suggests.
अनुपालन जानकारी
The listed product information identifies the MCP601 family as a low-power CMOS operational amplifier but does not state component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this general-purpose amplifier.