MCP601T-E/SN - 2.8MHz R-R Op Amp | Microchip Technology
MPN: MCP601T-E/SN ✓ NakahandaMCP601T-E/SN Ulas
An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to set its closed-loop behavior. The MCP601 belongs to the broader hierarchy of analog amplifiers, amplifier ICs, and semiconductor signal-conditioning devices. Its CMOS implementation emphasizes low bias current, low operating current, high open-loop gain, and rail-to-rail output capability, making it suitable for portable and low-voltage signal-processing systems.
Three defining characteristics are its 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. Rail-to-rail output swing allows the output voltage to approach the supply rails under suitable load conditions. Common-mode input operation below ground is valuable in single-supply circuits that process small signals centered around ground. Unity-gain stability supports direct use as a voltage follower when configured with its output connected to its inverting input.
The MCP601 uses Microchip’s advanced CMOS technology. This architecture provides low bias current, which is important when the amplifier must sense signals from high-impedance sources without loading them aggressively. Its 2.8 MHz gain-bandwidth product provides more bandwidth than many low-power general-purpose amplifiers, while the 230 uA typical operating current supports designs where supply consumption is an important constraint. Rail-to-rail output swing improves usable output range on low-voltage rails.
Typical applications include sensor-signal conditioning, portable instrumentation, battery-powered measurement systems, audio preamplification, and low-voltage analog signal chains. The device is also useful as a buffer or active filter when the selected feedback network keeps the closed-loop gain and bandwidth within stable operating limits. Because its input range can extend below ground, it can simplify signal conditioning around a zero-volt reference.
When designing around the MCP601T-E/SN, use the manufacturer’s recommended bypass-capacitor and stability guidance, place input and output networks close to the device, and verify output settling for the intended closed-loop gain. Designers should also check noise, offset, input-bias-current, and capacitive-loading behavior against the specific signal source rather than relying only on nominal gain-bandwidth figures.
This product page combines the manufacturer specifications with engineering-focused selection guidance, drop-in replacement information, application context, and practical PCB design notes. It also distinguishes temperature-grade and packaging variants within the MCP601 family so engineers can assess PCB reuse and production interchangeability before committing to a source.
Mga alternatibo na pwedeng ilagay na MCP601T-E/SN — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MCP601T-E/SN (parehas na form factor at footprint) — pagkakaiba sa Package, Gain-Bandwidth Product, Product Type, Typical Operating Current, Maximum Supply Voltage.
MCP601T-I/SN
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MCP601-E/SN
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MCP601T-I/ST
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →MCP601T-E/SN Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Single operational amplifier |
| Amplifier Configuration | 1 circuit |
| Technology | CMOS |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Offset Voltage | <2 mV |
| Output Swing | Rail-to-rail |
| Common-Mode Input | Includes input below ground |
| Closed-Loop Gain Stability | Unity gain stable |
| Packhaging | 8-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Shipping Format | Tape and reel |
Gabay sa Pin Configuration ng MCP601T-E/SN 8-pin soic
Pin configuration para sa MCP601T-E/SN (8-pin soic package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa MCP601T-E/SN.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MCP601T-E/SN ay nararapat para sa 6 aplikasyons: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Low-Voltage Audio Preamplifier, Industrial Current and Voltage Buffering, Active Analog Filtering, Portable Test and Measurement Front End.
Portable Sensor Signal Conditioning
The MCP601T-E/SN is appropriate for conditioning signals from low-power sensors in portable measurement systems. Its 230 uA typical operating current limits amplifier contribution to total supply consumption, while the 2.8 MHz gain-bandwidth product provides useful bandwidth for sensor and instrumentation signals. A non-inverting or differential input stage can use the amplifier’s input and output ratings, provided the selected gain remains stable. Check input bias current against the sensor impedance and confirm that signal amplitudes remain inside the common-mode range.
Inirekomenda
Battery-Powered Data Acquisition
A battery-powered data-acquisition front end benefits from the MCP601T-E/SN because it operates from a single 2.7 V to 5.5 V supply and has 230 uA typical operating current. Rail-to-rail output swing increases the usable signal range in compact systems, particularly when the supply voltage is close to the sensor output span. The amplifier can buffer inputs or implement active filtering, but the engineer must verify offset, bias-current effects, noise, and closed-loop stability across the expected signal bandwidth.
Inirekomenda
Low-Voltage Audio Preamplifier
The MCP601T-E/SN can serve as a low-voltage audio preamplifier stage when the required bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Rail-to-rail output allows the stage to approach the available supply swing, while operation from supplies as low as 2.7 V supports compact audio systems. The design should account for input bias current, output drive into the next stage, noise performance, and the maximum capacitive load. Feedback-component selection must preserve stability at the selected closed-loop gain.
Inirekomenda
Industrial Current and Voltage Buffering
The MCP601T-E/SN can buffer high-impedance voltage sources in industrial measurement systems where a low 230 uA typical operating current is useful. Its common-mode input capability extends below ground, allowing it to process signals centered around a zero-volt reference in single-supply systems. Use it as a voltage follower when the source cannot drive the measurement chain directly. Verify the source impedance against input bias current, provide appropriate bypassing, and keep feedback routing short to reduce sensitivity to noise and capacitive loading.
Inirekomenda
Active Analog Filtering
The MCP601T-E/SN is usable in first-order and higher-order active-filter networks when the closed-loop bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Single-supply operation from 2.7 V to 5.5 V simplifies filtering around a midpoint reference, and rail-to-rail output helps preserve signal amplitude near the supply limits. Exact resistor and capacitor values must be calculated from the desired cutoff, gain, and Q. Confirm noise, offset, and stability across temperature before using the stage for precision measurements.
Inirekomenda
Portable Test and Measurement Front End
The MCP601T-E/SN can form the input amplifier of a portable test-and-measurement instrument when low power and compact single-supply operation are priorities. Its 2.8 MHz gain-bandwidth product supports a broader range of low-frequency and modest intermediate-frequency measurements than a very slow precision amplifier. Use the rail-to-rail output range to maximize signal span, while selecting resistor networks for low offset and appropriate bias-current behavior. Add supply bypassing near the device and verify that source capacitance does not impair settling or stability.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MCP601T-E/SN — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MCP601T-I/SN | MCP601-E/SN | MCP601T-I/ST |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier | Single amplifier |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Typical Offset Voltage | <2 mV | <2 mV | <2 mV | <2 mV |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Code | T tape-and-reel format | T tape-and-reel format | SN format | ST format |
| Temperature Grade | E grade | I grade | E grade | I grade |
Pangunahing mga Pagkakaiba
- Higher bandwidth than a basic low-power amplifier (kumpara saLower-bandwidth general-purpose CMOS op amps)
- Useful output range in compact single-supply systems (kumpara saNon-rail-to-rail input amplifiers)
- Direct family reuse across environmental grades (kumpara saMCP601T-E/SN)
Talaan ng Disenyo
Place the supply bypass capacitor close to the positive and ground pins, and keep the feedback loop compact around the amplifier. A short output route reduces susceptibility to capacitive loading and parasitic feedback. Connect the exposed analog signal paths away from digital clock and switching nodes to preserve the benefit of the low-noise operating characteristics.
Do not select the amplifier from gain-bandwidth product alone. Check closed-loop stability, input and output common-mode limits, load current, output swing, and source impedance. A 2.8 MHz gain-bandwidth product is useful for bandwidth planning, but the usable signal bandwidth depends on noise gain and the feedback network implemented on the PCB.
For high-impedance sensors, calculate the bias-current-induced error before selecting feedback and source resistors. Reduce resistance when bias current dominates, and use shielding or guarded routing when leakage and surface contamination are significant. For precision offset-sensitive circuits, use matched resistor networks and account for the less-than-2 mV typical offset specification in the error budget.
Single-supply operation simplifies routing, but every signal referenced above ground must remain inside the amplifier’s common-mode range and every output must remain inside its output-swing capability. Verify these limits at the lowest supply voltage, highest temperature, and heaviest load because the practical output range is narrower than an ideal rail-to-rail model suggests.
Impormasyon ng Pagsunod sa Kautusan
The listed product information identifies the MCP601 family as a low-power CMOS operational amplifier but does not state component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this general-purpose amplifier.