MCP601T-E/SN - 2.8MHz R-R Op Amp | Microchip Technology
MPN: MCP601T-E/SN ✓ 啟用中MCP601T-E/SN 概覽
An operational amplifier, or op amp, is a voltage-gain amplifier that uses external feedback to set its closed-loop behavior. The MCP601 belongs to the broader hierarchy of analog amplifiers, amplifier ICs, and semiconductor signal-conditioning devices. Its CMOS implementation emphasizes low bias current, low operating current, high open-loop gain, and rail-to-rail output capability, making it suitable for portable and low-voltage signal-processing systems.
Three defining characteristics are its 2.8 MHz gain-bandwidth product, 230 uA typical operating current, and less than 2 mV typical offset voltage. Rail-to-rail output swing allows the output voltage to approach the supply rails under suitable load conditions. Common-mode input operation below ground is valuable in single-supply circuits that process small signals centered around ground. Unity-gain stability supports direct use as a voltage follower when configured with its output connected to its inverting input.
The MCP601 uses Microchip’s advanced CMOS technology. This architecture provides low bias current, which is important when the amplifier must sense signals from high-impedance sources without loading them aggressively. Its 2.8 MHz gain-bandwidth product provides more bandwidth than many low-power general-purpose amplifiers, while the 230 uA typical operating current supports designs where supply consumption is an important constraint. Rail-to-rail output swing improves usable output range on low-voltage rails.
Typical applications include sensor-signal conditioning, portable instrumentation, battery-powered measurement systems, audio preamplification, and low-voltage analog signal chains. The device is also useful as a buffer or active filter when the selected feedback network keeps the closed-loop gain and bandwidth within stable operating limits. Because its input range can extend below ground, it can simplify signal conditioning around a zero-volt reference.
When designing around the MCP601T-E/SN, use the manufacturer’s recommended bypass-capacitor and stability guidance, place input and output networks close to the device, and verify output settling for the intended closed-loop gain. Designers should also check noise, offset, input-bias-current, and capacitive-loading behavior against the specific signal source rather than relying only on nominal gain-bandwidth figures.
This product page combines the manufacturer specifications with engineering-focused selection guidance, drop-in replacement information, application context, and practical PCB design notes. It also distinguishes temperature-grade and packaging variants within the MCP601 family so engineers can assess PCB reuse and production interchangeability before committing to a source.
直接替換替代品,適用於 MCP601T-E/SN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: MCP601T-E/SN (相同外形與佔位) — 差異在於 Package, Gain-Bandwidth Product, Product Type, Typical Operating Current, Maximum Supply Voltage.
MCP601T-I/SN
✅ 直接替換聯絡詢價
查看資料表 →MCP601-E/SN
✅ 直接替換聯絡詢價
查看資料表 →MCP601T-I/ST
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →MCP601T-E/SN 最大額定值與電氣特性
| Product Type | Single operational amplifier |
| Amplifier Configuration | 1 circuit |
| Technology | CMOS |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 2.8 MHz |
| Typical Operating Current | 230 uA |
| Typical Offset Voltage | <2 mV |
| Output Swing | Rail-to-rail |
| Common-Mode Input | Includes input below ground |
| Closed-Loop Gain Stability | Unity gain stable |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
| Shipping Format | Tape and reel |
MCP601T-E/SN 8-pin soic 腳位配置指南
MCP601T-E/SN(8-pin soic 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: MCP601T-E/SN.
請參閱 資料表 以查看完整腳位配置。
典型應用
MCP601T-E/SN 適用於 6 應用s: Portable Sensor Signal Conditioning, Battery-Powered Data Acquisition, Low-Voltage Audio Preamplifier, Industrial Current and Voltage Buffering, Active Analog Filtering, Portable Test and Measurement Front End.
Portable Sensor Signal Conditioning
The MCP601T-E/SN is appropriate for conditioning signals from low-power sensors in portable measurement systems. Its 230 uA typical operating current limits amplifier contribution to total supply consumption, while the 2.8 MHz gain-bandwidth product provides useful bandwidth for sensor and instrumentation signals. A non-inverting or differential input stage can use the amplifier’s input and output ratings, provided the selected gain remains stable. Check input bias current against the sensor impedance and confirm that signal amplitudes remain inside the common-mode range.
推薦
Battery-Powered Data Acquisition
A battery-powered data-acquisition front end benefits from the MCP601T-E/SN because it operates from a single 2.7 V to 5.5 V supply and has 230 uA typical operating current. Rail-to-rail output swing increases the usable signal range in compact systems, particularly when the supply voltage is close to the sensor output span. The amplifier can buffer inputs or implement active filtering, but the engineer must verify offset, bias-current effects, noise, and closed-loop stability across the expected signal bandwidth.
推薦
Low-Voltage Audio Preamplifier
The MCP601T-E/SN can serve as a low-voltage audio preamplifier stage when the required bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Rail-to-rail output allows the stage to approach the available supply swing, while operation from supplies as low as 2.7 V supports compact audio systems. The design should account for input bias current, output drive into the next stage, noise performance, and the maximum capacitive load. Feedback-component selection must preserve stability at the selected closed-loop gain.
推薦
Industrial Current and Voltage Buffering
The MCP601T-E/SN can buffer high-impedance voltage sources in industrial measurement systems where a low 230 uA typical operating current is useful. Its common-mode input capability extends below ground, allowing it to process signals centered around a zero-volt reference in single-supply systems. Use it as a voltage follower when the source cannot drive the measurement chain directly. Verify the source impedance against input bias current, provide appropriate bypassing, and keep feedback routing short to reduce sensitivity to noise and capacitive loading.
推薦
Active Analog Filtering
The MCP601T-E/SN is usable in first-order and higher-order active-filter networks when the closed-loop bandwidth is compatible with its 2.8 MHz gain-bandwidth product. Single-supply operation from 2.7 V to 5.5 V simplifies filtering around a midpoint reference, and rail-to-rail output helps preserve signal amplitude near the supply limits. Exact resistor and capacitor values must be calculated from the desired cutoff, gain, and Q. Confirm noise, offset, and stability across temperature before using the stage for precision measurements.
推薦
Portable Test and Measurement Front End
The MCP601T-E/SN can form the input amplifier of a portable test-and-measurement instrument when low power and compact single-supply operation are priorities. Its 2.8 MHz gain-bandwidth product supports a broader range of low-frequency and modest intermediate-frequency measurements than a very slow precision amplifier. Use the rail-to-rail output range to maximize signal span, while selecting resistor networks for low offset and appropriate bias-current behavior. Add supply bypassing near the device and verify that source capacitance does not impair settling or stability.
推薦
推薦產品摘要
工程參考資料,適用於 MCP601T-E/SN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | MCP601T-I/SN | MCP601-E/SN | MCP601T-I/ST |
|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Single amplifier | Single amplifier | Single amplifier | Single amplifier |
| Gain-Bandwidth Product | 2.8 MHz | 2.8 MHz | 2.8 MHz | 2.8 MHz |
| Typical Operating Current | 230 uA | 230 uA | 230 uA | 230 uA |
| Typical Offset Voltage | <2 mV | <2 mV | <2 mV | <2 mV |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Shipping Code | T tape-and-reel format | T tape-and-reel format | SN format | ST format |
| Temperature Grade | E grade | I grade | E grade | I grade |
主要差異化特點
- Higher bandwidth than a basic low-power amplifier (對比Lower-bandwidth general-purpose CMOS op amps)
- Useful output range in compact single-supply systems (對比Non-rail-to-rail input amplifiers)
- Direct family reuse across environmental grades (對比MCP601T-E/SN)
設計說明
Place the supply bypass capacitor close to the positive and ground pins, and keep the feedback loop compact around the amplifier. A short output route reduces susceptibility to capacitive loading and parasitic feedback. Connect the exposed analog signal paths away from digital clock and switching nodes to preserve the benefit of the low-noise operating characteristics.
Do not select the amplifier from gain-bandwidth product alone. Check closed-loop stability, input and output common-mode limits, load current, output swing, and source impedance. A 2.8 MHz gain-bandwidth product is useful for bandwidth planning, but the usable signal bandwidth depends on noise gain and the feedback network implemented on the PCB.
For high-impedance sensors, calculate the bias-current-induced error before selecting feedback and source resistors. Reduce resistance when bias current dominates, and use shielding or guarded routing when leakage and surface contamination are significant. For precision offset-sensitive circuits, use matched resistor networks and account for the less-than-2 mV typical offset specification in the error budget.
Single-supply operation simplifies routing, but every signal referenced above ground must remain inside the amplifier’s common-mode range and every output must remain inside its output-swing capability. Verify these limits at the lowest supply voltage, highest temperature, and heaviest load because the practical output range is narrower than an ideal rail-to-rail model suggests.
合規資訊
The listed product information identifies the MCP601 family as a low-power CMOS operational amplifier but does not state component-level RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not indicated for this general-purpose amplifier.