THS1230IPW - 12-Bit 30 MSPS ADC | Texas Instruments
MPN: THS1230IPW ✓ सक्रियTHS1230IPW अवलोकन
An ADC is a data-acquisition IC that converts an analog voltage into a numeric value. The THS1230 belongs to the pipelined ADC hierarchy, where internal stages permit operation at sampling rates above those of many comparator-based flash converters. Its parallel output transfers each 12-bit conversion through dedicated digital pins, making the device appropriate for systems in which an FPGA, ASIC, or microcontroller captures high-rate samples through a parallel bus.
The primary specifications are a 12-bit conversion resolution, a maximum sampling rate of 30 MSPS, and a single differential input. The converter operates from a 3.3 V supply and supports an operating temperature range of -40 °C to +85 °C. A power-down mode reduces activity when acquisition is not required, while the pipeline architecture supports continuous high-rate sampling.
The device uses a differential analog input architecture and a parallel output configuration. The 28-pin TSSOP package is suitable for conventional surface-mount PCB assembly, although the high-speed parallel bus requires careful routing to minimize timing and signal-integrity errors. The one-input architecture reduces analog channel count while concentrating performance on a single high-speed waveform.
Typical uses include communications receivers, radar or sonar signal processing, industrial measurement systems, digital oscilloscopes, waveform recorders, and medical or scientific instrumentation. In these systems, the 30 MSPS rate captures rapidly changing waveforms, while the 12-bit result provides 4,096 quantization levels. The parallel interface can feed an FPGA directly when bus timing and input capacitance are properly managed.
A critical design consideration is analog and digital layout separation. Keep the analog input path short, use a stable reference and regulated analog supply, and route the 12-bit output bus over controlled-impedance layers. Avoid long stubs and unnecessary vias between the THS1230IPW and the receiving digital device.
This page consolidates the confirmed conversion specifications, package information, lifecycle context, replacement analysis, and practical implementation guidance into an engineering-oriented reference for evaluating the THS1230IPW in high-speed data-acquisition designs.
के लिए ड्रॉप-इन विकल्प THS1230IPW — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं THS1230IPW (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Architecture, Input Type, Operating Temperature, Package, Resolution.
THS1230IDW
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →THS1230CDW
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →THS1230CDWG4
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →THS1230IPWG4
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
THS1215IPW
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापितकीमत के लिए संपर्क करें
डेटाशीट देखें →THS1230IPW Maximum Ratings और Electrical Characteristics
| रेज़ोल्यूशन | 12 bit |
| सैंपलिंग रेट | 30 MSPS |
| Number of Input Channels | 1 channel |
| Input Configuration | Differential |
| Analog Supply Voltage | 3.3 V |
| Architecture | Pipelined ADC |
| Output Interface | 12-bit parallel |
| Input Type | Single analog input |
| Sample-and-Hold | Yes |
| Power-Down Function | Yes |
| ऑपरेटिंग तापमान रेंज | -40 °C to +85 °C |
| पैकेज | 28-pin TSSOP |
| Package Width | 4.40 mm |
| माउंटिंग प्रकार | Surface mount |
| Shipping Format | Tube |
| Power Class | Low-power ADC |
| RoHS स्थिति | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
THS1230IPW 4.40 mm पिन कॉन्फ़िगरेशन गाइड
THS1230IPW (4.40 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: THS1230IPW.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
THS1230IPW के लिए उपयुक्त है 6 अनुप्रयोगs: Communications Receiver, Radar Signal Processing, Industrial Waveform Acquisition, Digital Oscilloscope, Medical Signal Acquisition, Test and Measurement.
Communications Receiver
The THS1230IPW is appropriate for capturing received intermediate-frequency or baseband waveforms that change rapidly and require direct digital processing. Its 30 MSPS conversion rate and 12-bit resolution provide 4,096 discrete levels per sample, while the differential input supports balanced analog drive and improved rejection of common-mode noise. The parallel output can connect to an FPGA or ASIC when trace length, clock skew, and input loading are controlled. Compared with a serialized interface, the 12-bit parallel bus increases routing complexity but avoids serializing every 30 MSPS sample, making this converter suitable for communications receivers requiring predictable high-throughput capture.
अनुशंसित
Radar Signal Processing
The THS1230IPW can sample radar or sonar waveforms at 30 MSPS when the system needs more temporal resolution than a slower general-purpose ADC provides. A 12-bit conversion result preserves a useful balance between waveform fidelity and processing bandwidth for detection, analysis, and feedback control. The differential analog input helps the front end reject noise present equally on both signal lines. Its parallel output is well suited to FPGA-based digital signal processing, although clock jitter and analog bandwidth must be engineered around the sampling rate rather than treated only as ADC specifications.
अनुशंसित
Industrial Waveform Acquisition
The THS1230IPW suits industrial monitoring systems that must capture transient events, vibration signatures, or rapidly changing sensor outputs. At 30 MSPS and 12-bit resolution, it provides 4,096 quantization levels while retaining a high sample rate for event analysis. The 3.3 V analog supply and differential input simplify integration with active analog front ends, while power-down operation can reduce consumption during idle intervals. For factory equipment, the principal implementation concern is isolating the high-speed parallel bus from motor-control and switching-node noise on the PCB.
अनुशंसित
Digital Oscilloscope
The THS1230IPW can serve as the acquisition front end in a digital oscilloscope or waveform recorder requiring 30 MSPS sampling. The 12-bit resolution creates 4,096 vertical codes, which allows the instrument to represent captured waveforms without using only a small portion of the converter range. The parallel output supports direct transfer into a capture FPGA, reducing the overhead of serial transmission across a multi-gigabit-per-second sample stream. The main trade-off is the large number of high-speed output traces, which require a carefully partitioned board and short, impedance-controlled connections.
अनुशंसित
Medical Signal Acquisition
The THS1230IPW can be used in diagnostic and monitoring equipment that captures burst-mode physiological or instrumentation signals at up to 30 MSPS. Its differential input is helpful when the analog front end can present balanced signals, while its 12-bit resolution supports detailed waveform measurement. Power-down capability is useful in portable systems that spend substantial time between acquisition bursts. Designers must still implement appropriate input protection, isolation, noise control, and analog bandwidth limits; the ADC rating alone does not establish compliance with any medical-system requirement.
अनुशंसित
Test and Measurement
The THS1230IPW is suitable for high-speed test and measurement front ends that need to digitize repetitive or transient waveforms for later analysis. The 30 MSPS sampling rate provides higher temporal resolution than the THS1215IPW's 15 MSPS maximum rate, while both retain the 12-bit parallel-output architecture. In an instrument, the converter can feed a capture FPGA followed by digital filtering, triggering, or analysis. Careful decoupling, reference stability, clock distribution, and analog-to-digital trace isolation are essential for repeatable measurements at the converter's full sampling rate.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा THS1230IPW — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | THS1230IDW | THS1230CDW | THS1230CDWG4 | THS1230IPWG4 | THS1215IPW |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Sampling Rate | 30 MSPS | 30 MSPS | 30 MSPS | 30 MSPS | 30 MSPS | 15 MSPS, 50% lower |
| Number of Input Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Input Configuration | Differential | Differential | Differential | Differential | Differential | Differential |
मुख्य विशेषताएँ
- Higher conversion rate than the lower-speed family alternative (बनामTHS1215IPW)
- Same confirmed converter performance as direct family variants (बनामTHS1230IDW)
- Parallel output supports high-throughput acquisition (बनामTHS1215IPW)
- Direct same-family replacement footprint (बनामTHS1230CDW)
डिज़ाइन नोट्स
Partition the PCB into analog and digital regions and place the THS1230IPW near the boundary. Route the differential analog input as a short, tightly coupled pair with no stubs, and terminate it according to the manufacturer application circuit. Keep the sampling clock and 12-bit output bus away from the input and reference nodes to reduce coupling from the 30 MSPS conversion and output transitions.
Treat the 12-bit parallel output as a synchronous high-speed bus. Match output and receiver trace lengths where timing margins permit, provide continuous reference planes, minimize layer transitions and vias, and confirm input capacitance at the FPGA or ASIC. The 30 MSPS conversion rate creates frequent output activity even when the numerical resolution is only 12 bits, so logical trace count alone does not describe the signal-integrity requirement.
Follow the manufacturer datasheet for analog and digital supply decoupling, using the shortest practical path from each capacitor to its associated power pin. Keep switching-regulator and high-current digital return paths away from the reference and analog input nodes. The power-down feature can reduce consumption during idle periods, but rail state transitions and acquisition restart behavior should be tested in the complete system rather than assumed instantaneous.
Do not treat a shared 28-pin TSSOP footprint alone as proof that any ADC is interchangeable with the THS1230IPW. Verify the complete pin-description table, analog input range, reference voltage, clock polarity, configuration pins, output timing, and power sequence. In particular, confirm the CON0 and CON1 operating modes and any dependencies between power-down, standby, and differential configuration.
अनुपालन जानकारी
The manufacturer product information confirms an analog-to-digital converter and 28-pin TSSOP package, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified. AEC-Q100 is not applicable because the target is not described as an automotive-qualified ADC.