Texas Instruments

THS1230IPW - 12-Bit 30 MSPS ADC | Texas Instruments

MPN: THS1230IPW ✓ 啟用中
3.3 V Vdss 28-pin TSSOP Package
MOQ: 1 |

THS1230IPW 概覽

The Texas Instruments THS1230IPW is a single-channel, 12-bit, 30 MSPS pipelined analog-to-digital converter operating from a 3.3 V supply and housed in a 28-pin TSSOP package. It provides a parallel digital interface, a differential analog input, a sample-and-hold stage, and a power-down function for low-power acquisition systems. Its 30 MSPS conversion rate and 12-bit resolution are suited to high-speed signal capture, communications, instrumentation, and industrial control applications.

An ADC is a data-acquisition IC that converts an analog voltage into a numeric value. The THS1230 belongs to the pipelined ADC hierarchy, where internal stages permit operation at sampling rates above those of many comparator-based flash converters. Its parallel output transfers each 12-bit conversion through dedicated digital pins, making the device appropriate for systems in which an FPGA, ASIC, or microcontroller captures high-rate samples through a parallel bus.

The primary specifications are a 12-bit conversion resolution, a maximum sampling rate of 30 MSPS, and a single differential input. The converter operates from a 3.3 V supply and supports an operating temperature range of -40 °C to +85 °C. A power-down mode reduces activity when acquisition is not required, while the pipeline architecture supports continuous high-rate sampling.

The device uses a differential analog input architecture and a parallel output configuration. The 28-pin TSSOP package is suitable for conventional surface-mount PCB assembly, although the high-speed parallel bus requires careful routing to minimize timing and signal-integrity errors. The one-input architecture reduces analog channel count while concentrating performance on a single high-speed waveform.

Typical uses include communications receivers, radar or sonar signal processing, industrial measurement systems, digital oscilloscopes, waveform recorders, and medical or scientific instrumentation. In these systems, the 30 MSPS rate captures rapidly changing waveforms, while the 12-bit result provides 4,096 quantization levels. The parallel interface can feed an FPGA directly when bus timing and input capacitance are properly managed.

A critical design consideration is analog and digital layout separation. Keep the analog input path short, use a stable reference and regulated analog supply, and route the 12-bit output bus over controlled-impedance layers. Avoid long stubs and unnecessary vias between the THS1230IPW and the receiving digital device.

This page consolidates the confirmed conversion specifications, package information, lifecycle context, replacement analysis, and practical implementation guidance into an engineering-oriented reference for evaluating the THS1230IPW in high-speed data-acquisition designs.

直接替換替代品,適用於 THS1230IPW — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: THS1230IPW (相同外形與佔位) — 差異在於 Architecture, Input Type, Operating Temperature, Package, Resolution.

Texas Instruments
Architecture: Pipelined CMOS ADC
Operating Temperature: -40C to +85C
Package: 28-TSSOP (PW), 9.7 mm x 6.4 mm
比較對象 THS1230IPW →
Texas Instruments
Architecture: Pipelined / multi-stage with digital error correction
Input Type: Configurable: single-ended, single-ended with offset, or differential
Operating Temperature: 0 °C to +70 °C (C-grade commercial)
比較對象 THS1230IPW →
Texas Instruments
Architecture: Pipelined, multi-stage
Resolution: 12 bits
比較對象 THS1230IPW →
Texas Instruments
Architecture: Pipelined
Input Type: Differential / Single-Ended
Operating Temperature: 0C to +70C
比較對象 THS1230IPW →

THS1230IDW

✅ 直接替換
Texas Instruments
📦 28-TSSOP
Pipelined ADC · 12 bit · 1 channel · 1 input · 30 MSPS · 3.3 V · -2 V to +2 V · 0.0488%

聯絡詢價

查看資料表 →

THS1230CDW

✅ 直接替換
Texas Instruments
📦 28-TSSOP
12 bits · 30 MSPS · 1 · 3.3 V (single supply) · Pipelined / multi-stage with digital error correction · Configurable: single-ended, single-ended with offset, or differential

聯絡詢價

查看資料表 →

THS1230CDWG4

✅ 直接替換
Texas Instruments
📦 28-TSSOP
12 bits · 30 MSPS · 1 · 0.033 us (approx. 33 ns) · Pipelined, multi-stage · Parallel CMOS · Differential or single-ended · 3.3 V

聯絡詢價

查看資料表 →

THS1230IPWG4

✅ 直接替換
📦 28-TSSOP
Same 12-bit, 30 MSPS converter and 28-TSSOP footprint; the G4 ordering grade differs while the confirmed sampling rate and resolution remain unchanged.

📋 參考替代品(不在目錄中)

THS1215IPW

✅ 直接替換 ⚠️ 規格未經驗證
Texas Instruments
📦 28-TSSOP
12 bit · 15 MSPS · 3.3 V (single supply) · Pipelined CMOS ADC · 1 · Single-ended / Single-ended with offset / Differential · 150 MHz (typ) · 1 Vpp to 2 Vpp differential

聯絡詢價

查看資料表 →

THS1230IPW 最大額定值與電氣特性

解析度 12 bit
取樣率 30 MSPS
Number of Input Channels 1 channel
Input Configuration Differential
Analog Supply Voltage 3.3 V
Architecture Pipelined ADC
Output Interface 12-bit parallel
Input Type Single analog input
Sample-and-Hold Yes
Power-Down Function Yes
工作溫度範圍 -40 °C to +85 °C
封裝 28-pin TSSOP
Package Width 4.40 mm
安裝類型 Surface mount
Shipping Format Tube
Power Class Low-power ADC
RoHS 狀態 Unknown
REACH Status Unknown
AEC-Q100 Qualification Not applicable

THS1230IPW 4.40 mm 腳位配置指南

THS1230IPW(4.40 mm 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

THS1230IPW 的 4.40 mm 封裝腳位圖

無詳細腳位定義資料: THS1230IPW.

請參閱 資料表 以查看完整腳位配置。

典型應用

THS1230IPW 適用於 6 應用s: Communications Receiver, Radar Signal Processing, Industrial Waveform Acquisition, Digital Oscilloscope, Medical Signal Acquisition, Test and Measurement.

🌐

Communications Receiver

The THS1230IPW is appropriate for capturing received intermediate-frequency or baseband waveforms that change rapidly and require direct digital processing. Its 30 MSPS conversion rate and 12-bit resolution provide 4,096 discrete levels per sample, while the differential input supports balanced analog drive and improved rejection of common-mode noise. The parallel output can connect to an FPGA or ASIC when trace length, clock skew, and input loading are controlled. Compared with a serialized interface, the 12-bit parallel bus increases routing complexity but avoids serializing every 30 MSPS sample, making this converter suitable for communications receivers requiring predictable high-throughput capture.

✈️

Radar Signal Processing

The THS1230IPW can sample radar or sonar waveforms at 30 MSPS when the system needs more temporal resolution than a slower general-purpose ADC provides. A 12-bit conversion result preserves a useful balance between waveform fidelity and processing bandwidth for detection, analysis, and feedback control. The differential analog input helps the front end reject noise present equally on both signal lines. Its parallel output is well suited to FPGA-based digital signal processing, although clock jitter and analog bandwidth must be engineered around the sampling rate rather than treated only as ADC specifications.

🏭

Industrial Waveform Acquisition

The THS1230IPW suits industrial monitoring systems that must capture transient events, vibration signatures, or rapidly changing sensor outputs. At 30 MSPS and 12-bit resolution, it provides 4,096 quantization levels while retaining a high sample rate for event analysis. The 3.3 V analog supply and differential input simplify integration with active analog front ends, while power-down operation can reduce consumption during idle intervals. For factory equipment, the principal implementation concern is isolating the high-speed parallel bus from motor-control and switching-node noise on the PCB.

📺

Digital Oscilloscope

The THS1230IPW can serve as the acquisition front end in a digital oscilloscope or waveform recorder requiring 30 MSPS sampling. The 12-bit resolution creates 4,096 vertical codes, which allows the instrument to represent captured waveforms without using only a small portion of the converter range. The parallel output supports direct transfer into a capture FPGA, reducing the overhead of serial transmission across a multi-gigabit-per-second sample stream. The main trade-off is the large number of high-speed output traces, which require a carefully partitioned board and short, impedance-controlled connections.

💊

Medical Signal Acquisition

The THS1230IPW can be used in diagnostic and monitoring equipment that captures burst-mode physiological or instrumentation signals at up to 30 MSPS. Its differential input is helpful when the analog front end can present balanced signals, while its 12-bit resolution supports detailed waveform measurement. Power-down capability is useful in portable systems that spend substantial time between acquisition bursts. Designers must still implement appropriate input protection, isolation, noise control, and analog bandwidth limits; the ADC rating alone does not establish compliance with any medical-system requirement.

🔧

Test and Measurement

The THS1230IPW is suitable for high-speed test and measurement front ends that need to digitize repetitive or transient waveforms for later analysis. The 30 MSPS sampling rate provides higher temporal resolution than the THS1215IPW's 15 MSPS maximum rate, while both retain the 12-bit parallel-output architecture. In an instrument, the converter can feed a capture FPGA followed by digital filtering, triggering, or analysis. Careful decoupling, reference stability, clock distribution, and analog-to-digital trace isolation are essential for repeatable measurements at the converter's full sampling rate.

What is the THS1230IPW?
The THS1230IPW is a Texas Instruments single-channel, 12-bit, 30 MSPS pipelined analog-to-digital converter with a differential input and parallel output. According to the manufacturer datasheet, it operates from a 3.3 V supply and includes a power-down function. The device is packaged in a 28-pin TSSOP for high-speed data-acquisition and signal-processing systems.
What is the sampling rate and resolution of THS1230IPW?
The THS1230IPW samples at up to 30 MSPS and provides 12-bit resolution, corresponding to 4,096 quantization levels for each conversion. According to the manufacturer datasheet, the device combines a pipelined ADC architecture with a parallel digital interface. This combination is intended for applications requiring faster conversion than many general-purpose successive-approximation ADCs can provide.
What is the supply voltage of THS1230IPW?
The THS1230IPW operates from a 3.3 V supply. The manufacturer datasheet identifies the part as a 3.3 V, 12-bit, 30 MSPS low-power analog-to-digital converter with power-down capability. Designers should use a regulated 3.3 V source and follow the datasheet sequencing and decoupling requirements when connecting analog and digital supply pins.
What interface does the THS1230IPW use?
The THS1230IPW uses a 12-bit parallel digital interface. According to the manufacturer datasheet, each conversion is presented on dedicated output lines instead of being serialized through an SPI or I2C link. This interface can provide high throughput at 30 MSPS, but it requires careful PCB routing, matched input timing, and adequate receiver drive capability.
Is the THS1230IPW a single-channel or differential ADC?
The THS1230IPW is a single-channel ADC with a differential analog input arrangement. The manufacturer datasheet lists one input, while the converter uses paired signal terminals for differential operation. This architecture is useful for rejecting common-mode noise and disturbances when the source can be arranged to drive a balanced analog signal.
Where can I download the THS1230IPW datasheet PDF?
The THS1230IPW datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/ths1230.pdf. The manufacturer document describes the 3.3 V supply, 12-bit resolution, 30 MSPS sampling rate, power-down operation, configuration controls, electrical characteristics, and application information. Use the pin-description table and recommended application circuit when assigning PCB connections.
Where can I find the THS1230IPW pinout?
The THS1230IPW pinout is defined in the pin-configuration section of the Texas Instruments manufacturer datasheet. The device uses a 28-pin TSSOP package, and the datasheet also identifies differential operating modes controlled by CON0 and CON1. Use that table for signal assignments rather than inferring pin functions from another ADC in the same family.
What can replace the THS1230IPW without changing its PCB footprint?
The closest drop-in candidates are the same-family THS1230IDW and THS1230CDW devices in the 28-pin TSSOP format. Compatibility should still be confirmed against input range, timing, configuration, and temperature requirements. A lower-speed family member such as THS1215IPW may share the footprint but should be treated as a functional drop-in only after its timing and pin definitions are verified.
What is the best Texas Instruments equivalent for THS1230IPW?
The THS1230IDW and THS1230CDW are the most direct same-family alternatives because they retain the 12-bit, 30 MSPS converter class and 28-pin TSSOP format. Their commercial or temperature-grade differences determine the appropriate choice. Confirm the exact pinout, reference requirements, and operating-temperature range before approving either part as a drop-in replacement.
Is THS1230IPW suitable for communications and radar systems?
Yes, the THS1230IPW is suitable for communications, radar, and other waveform-acquisition systems that require a 30 MSPS conversion rate. Its 12-bit resolution and parallel output support direct capture into digital processing hardware. Differential input operation can improve noise immunity, although front-end bandwidth, sampling-clock jitter, and PCB signal integrity require careful design.
When should I choose THS1230IPW instead of THS1215IPW?
Choose THS1230IPW when the acquisition system requires the full 30 MSPS sampling capability of the THS1230 family. The THS1215IPW belongs to a lower-speed 15 MSPS class, so selecting it would reduce the achievable acquisition rate by approximately 50%. Choose the slower device only when its lower conversion rate, power profile, and timing behavior better match the application.
THS1230IPW vs THS1230IDW: which is better?
The THS1230IPW and THS1230IDW belong to the same 12-bit, 30 MSPS, 28-pin TSSOP family, so their converter performance is closely aligned. Selection should be based on grade, ordering information, operating-temperature coverage, and lifecycle requirements rather than raw sampling speed. Verify the suffix-specific markings and temperature range against the manufacturer datasheet before substitution.
Is THS1230IPW the same as THS1230CDW?
The THS1230IPW and THS1230CDW are closely related 12-bit, 30 MSPS ADCs in the same 28-pin TSSOP family, but their suffix-specific grades or ordering conditions can differ. They should not be treated as automatically identical without checking temperature range, qualification, and availability. Confirm the pin assignments and operating limits in the manufacturer documentation before replacement.
Where can I buy THS1230IPW and check its lead time?
Use the Request a Quote form on this page to request THS1230IPW pricing, stock confirmation, and current lead time. The device is a 28-pin TSSOP, single-channel, 12-bit, 30 MSPS ADC from Texas Instruments. Providing the required quantity, target packaging, and delivery location enables a current sourcing response without relying on stale catalog information.
What are the key specifications of THS1230IPW that engineers should know?
The key THS1230IPW specifications are 12-bit resolution, a 30 MSPS maximum sampling rate, one differential input, a 3.3 V supply, a 12-bit parallel output, and a 28-pin TSSOP package. According to the manufacturer datasheet, the converter also supports power-down operation and an operating range from -40 °C to +85 °C. These parameters define its suitability for high-speed acquisition systems.

工程參考資料,適用於 THS1230IPW — 比較、設計指引及合規資訊。

選型指南

Choose the THS1230IPW when a design needs a single-channel, 12-bit converter capable of 30 MSPS with a parallel output and 3.3 V operation. It is especially appropriate for communications, radar, waveform-capture, and industrial measurement systems that can capture samples directly into an FPGA or ASIC. Select THS1230IDW or THS1230CDW when their suffix-specific grade, temperature coverage, or commercial ordering conditions better fit the production program. The THS1230CDWG4 and THS1230IPWG4 variants retain the same 30 MSPS, 12-bit, 28-pin TSSOP performance and should be reviewed according to their specific ordering grade. Consider THS1215IPW only when 15 MSPS is sufficient; choosing it lowers the maximum sample rate by 50%. For every candidate, verify the complete pinout, reference voltage, analog input range, clock requirements, and timing specifications before approving a drop-in replacement.

與替代品比較

參數 本產品 THS1230IDW THS1230CDW THS1230CDWG4 THS1230IPWG4 THS1215IPW
Package 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP 28-pin TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Resolution 12 bit 12 bit 12 bit 12 bit 12 bit 12 bit
Maximum Sampling Rate 30 MSPS 30 MSPS 30 MSPS 30 MSPS 30 MSPS 15 MSPS, 50% lower
Number of Input Channels 1 channel 1 channel 1 channel 1 channel 1 channel 1 channel
Input Configuration Differential Differential Differential Differential Differential Differential

主要差異化特點

  • Higher conversion rate than the lower-speed family alternative (對比THS1215IPW)
  • Same confirmed converter performance as direct family variants (對比THS1230IDW)
  • Parallel output supports high-throughput acquisition (對比THS1215IPW)
  • Direct same-family replacement footprint (對比THS1230CDW)

設計說明

Partition the PCB into analog and digital regions and place the THS1230IPW near the boundary. Route the differential analog input as a short, tightly coupled pair with no stubs, and terminate it according to the manufacturer application circuit. Keep the sampling clock and 12-bit output bus away from the input and reference nodes to reduce coupling from the 30 MSPS conversion and output transitions.

Treat the 12-bit parallel output as a synchronous high-speed bus. Match output and receiver trace lengths where timing margins permit, provide continuous reference planes, minimize layer transitions and vias, and confirm input capacitance at the FPGA or ASIC. The 30 MSPS conversion rate creates frequent output activity even when the numerical resolution is only 12 bits, so logical trace count alone does not describe the signal-integrity requirement.

Follow the manufacturer datasheet for analog and digital supply decoupling, using the shortest practical path from each capacitor to its associated power pin. Keep switching-regulator and high-current digital return paths away from the reference and analog input nodes. The power-down feature can reduce consumption during idle periods, but rail state transitions and acquisition restart behavior should be tested in the complete system rather than assumed instantaneous.

Do not treat a shared 28-pin TSSOP footprint alone as proof that any ADC is interchangeable with the THS1230IPW. Verify the complete pin-description table, analog input range, reference voltage, clock polarity, configuration pins, output timing, and power sequence. In particular, confirm the CON0 and CON1 operating modes and any dependencies between power-down, standby, and differential configuration.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The manufacturer product information confirms an analog-to-digital converter and 28-pin TSSOP package, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified. AEC-Q100 is not applicable because the target is not described as an automotive-qualified ADC.

相關搜尋

THS1230IPW datasheet THS1230IPW datasheet pdf THS1230IPW pinout THS1230IPW specifications Texas Instruments THS1230IPW THS1230IPW 12-bit 30 MSPS ADC THS1230IPW equivalent THS1230IPW replacement THS1230IPW cross reference THS1230IPW vs THS1230IDW THS1230IPW footprint THS1230IPW application circuit THS1230IPW price THS1230IPW stock THS1230IPW vs THS1215IPW

相關元件與詞彙

Texas Instruments THS1230IPW THS1230IDW THS1230CDW THS1230CDWG4 THS1230IPWG4 THS1215IPW analog-to-digital converter ADC pipelined ADC single-channel ADC differential input parallel output interface 12-bit resolution 30 MSPS sampling rate 3.3 V analog supply sample-and-hold power-down mode 28-pin TSSOP TSSOP package family surface-mount technology FPGA data acquisition signal integrity RoHS REACH
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情