THS1230IPW - 12-Bit 30 MSPS ADC | Texas Instruments
料号: THS1230IPW ✓ 量产中THS1230IPW 概述
An ADC is a data-acquisition IC that converts an analog voltage into a numeric value. The THS1230 belongs to the pipelined ADC hierarchy, where internal stages permit operation at sampling rates above those of many comparator-based flash converters. Its parallel output transfers each 12-bit conversion through dedicated digital pins, making the device appropriate for systems in which an FPGA, ASIC, or microcontroller captures high-rate samples through a parallel bus.
The primary specifications are a 12-bit conversion resolution, a maximum sampling rate of 30 MSPS, and a single differential input. The converter operates from a 3.3 V supply and supports an operating temperature range of -40 °C to +85 °C. A power-down mode reduces activity when acquisition is not required, while the pipeline architecture supports continuous high-rate sampling.
The device uses a differential analog input architecture and a parallel output configuration. The 28-pin TSSOP package is suitable for conventional surface-mount PCB assembly, although the high-speed parallel bus requires careful routing to minimize timing and signal-integrity errors. The one-input architecture reduces analog channel count while concentrating performance on a single high-speed waveform.
Typical uses include communications receivers, radar or sonar signal processing, industrial measurement systems, digital oscilloscopes, waveform recorders, and medical or scientific instrumentation. In these systems, the 30 MSPS rate captures rapidly changing waveforms, while the 12-bit result provides 4,096 quantization levels. The parallel interface can feed an FPGA directly when bus timing and input capacitance are properly managed.
A critical design consideration is analog and digital layout separation. Keep the analog input path short, use a stable reference and regulated analog supply, and route the 12-bit output bus over controlled-impedance layers. Avoid long stubs and unnecessary vias between the THS1230IPW and the receiving digital device.
This page consolidates the confirmed conversion specifications, package information, lifecycle context, replacement analysis, and practical implementation guidance into an engineering-oriented reference for evaluating the THS1230IPW in high-speed data-acquisition designs.
直接替换替代料: THS1230IPW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: THS1230IPW (相同外形与封装尺寸) ——差异在于 Architecture, Input Type, Operating Temperature, Package, Resolution.
THS1230IDW
✅ 直接替换联系询价
查看数据手册 →THS1230CDW
✅ 直接替换联系询价
查看数据手册 →THS1230CDWG4
✅ 直接替换联系询价
查看数据手册 →THS1230IPWG4
✅ 直接替换📋 参考替代料(不在目录中)
THS1215IPW
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →THS1230IPW 最大额定值与电气特性
| 分辨率 | 12 bit |
| 采样率 | 30 MSPS |
| Number of Input Channels | 1 channel |
| Input Configuration | Differential |
| Analog Supply Voltage | 3.3 V |
| Architecture | Pipelined ADC |
| Output Interface | 12-bit parallel |
| Input Type | Single analog input |
| Sample-and-Hold | Yes |
| Power-Down Function | Yes |
| 工作温度范围 | -40 °C to +85 °C |
| 封装 | 28-pin TSSOP |
| Package Width | 4.40 mm |
| 安装类型 | Surface mount |
| Shipping Format | Tube |
| Power Class | Low-power ADC |
| RoHS 状态 | Unknown |
| REACH Status | Unknown |
| AEC-Q100 Qualification | Not applicable |
THS1230IPW 4.40 mm 引脚配置指南
THS1230IPW(4.40 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: THS1230IPW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
THS1230IPW 适用于 6 应用s: Communications Receiver, Radar Signal Processing, Industrial Waveform Acquisition, Digital Oscilloscope, Medical Signal Acquisition, Test and Measurement.
Communications Receiver
The THS1230IPW is appropriate for capturing received intermediate-frequency or baseband waveforms that change rapidly and require direct digital processing. Its 30 MSPS conversion rate and 12-bit resolution provide 4,096 discrete levels per sample, while the differential input supports balanced analog drive and improved rejection of common-mode noise. The parallel output can connect to an FPGA or ASIC when trace length, clock skew, and input loading are controlled. Compared with a serialized interface, the 12-bit parallel bus increases routing complexity but avoids serializing every 30 MSPS sample, making this converter suitable for communications receivers requiring predictable high-throughput capture.
推荐
Radar Signal Processing
The THS1230IPW can sample radar or sonar waveforms at 30 MSPS when the system needs more temporal resolution than a slower general-purpose ADC provides. A 12-bit conversion result preserves a useful balance between waveform fidelity and processing bandwidth for detection, analysis, and feedback control. The differential analog input helps the front end reject noise present equally on both signal lines. Its parallel output is well suited to FPGA-based digital signal processing, although clock jitter and analog bandwidth must be engineered around the sampling rate rather than treated only as ADC specifications.
推荐
Industrial Waveform Acquisition
The THS1230IPW suits industrial monitoring systems that must capture transient events, vibration signatures, or rapidly changing sensor outputs. At 30 MSPS and 12-bit resolution, it provides 4,096 quantization levels while retaining a high sample rate for event analysis. The 3.3 V analog supply and differential input simplify integration with active analog front ends, while power-down operation can reduce consumption during idle intervals. For factory equipment, the principal implementation concern is isolating the high-speed parallel bus from motor-control and switching-node noise on the PCB.
推荐
Digital Oscilloscope
The THS1230IPW can serve as the acquisition front end in a digital oscilloscope or waveform recorder requiring 30 MSPS sampling. The 12-bit resolution creates 4,096 vertical codes, which allows the instrument to represent captured waveforms without using only a small portion of the converter range. The parallel output supports direct transfer into a capture FPGA, reducing the overhead of serial transmission across a multi-gigabit-per-second sample stream. The main trade-off is the large number of high-speed output traces, which require a carefully partitioned board and short, impedance-controlled connections.
推荐
Medical Signal Acquisition
The THS1230IPW can be used in diagnostic and monitoring equipment that captures burst-mode physiological or instrumentation signals at up to 30 MSPS. Its differential input is helpful when the analog front end can present balanced signals, while its 12-bit resolution supports detailed waveform measurement. Power-down capability is useful in portable systems that spend substantial time between acquisition bursts. Designers must still implement appropriate input protection, isolation, noise control, and analog bandwidth limits; the ADC rating alone does not establish compliance with any medical-system requirement.
推荐
Test and Measurement
The THS1230IPW is suitable for high-speed test and measurement front ends that need to digitize repetitive or transient waveforms for later analysis. The 30 MSPS sampling rate provides higher temporal resolution than the THS1215IPW's 15 MSPS maximum rate, while both retain the 12-bit parallel-output architecture. In an instrument, the converter can feed a capture FPGA followed by digital filtering, triggering, or analysis. Careful decoupling, reference stability, clock distribution, and analog-to-digital trace isolation are essential for repeatable measurements at the converter's full sampling rate.
推荐
推荐产品汇总
工程参考数据: THS1230IPW ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | THS1230IDW | THS1230CDW | THS1230CDWG4 | THS1230IPWG4 | THS1215IPW |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| Maximum Sampling Rate | 30 MSPS | 30 MSPS | 30 MSPS | 30 MSPS | 30 MSPS | 15 MSPS, 50% lower |
| Number of Input Channels | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel | 1 channel |
| Input Configuration | Differential | Differential | Differential | Differential | Differential | Differential |
关键差异点
- Higher conversion rate than the lower-speed family alternative (对比 THS1215IPW)
- Same confirmed converter performance as direct family variants (对比 THS1230IDW)
- Parallel output supports high-throughput acquisition (对比 THS1215IPW)
- Direct same-family replacement footprint (对比 THS1230CDW)
设计说明
Partition the PCB into analog and digital regions and place the THS1230IPW near the boundary. Route the differential analog input as a short, tightly coupled pair with no stubs, and terminate it according to the manufacturer application circuit. Keep the sampling clock and 12-bit output bus away from the input and reference nodes to reduce coupling from the 30 MSPS conversion and output transitions.
Treat the 12-bit parallel output as a synchronous high-speed bus. Match output and receiver trace lengths where timing margins permit, provide continuous reference planes, minimize layer transitions and vias, and confirm input capacitance at the FPGA or ASIC. The 30 MSPS conversion rate creates frequent output activity even when the numerical resolution is only 12 bits, so logical trace count alone does not describe the signal-integrity requirement.
Follow the manufacturer datasheet for analog and digital supply decoupling, using the shortest practical path from each capacitor to its associated power pin. Keep switching-regulator and high-current digital return paths away from the reference and analog input nodes. The power-down feature can reduce consumption during idle periods, but rail state transitions and acquisition restart behavior should be tested in the complete system rather than assumed instantaneous.
Do not treat a shared 28-pin TSSOP footprint alone as proof that any ADC is interchangeable with the THS1230IPW. Verify the complete pin-description table, analog input range, reference voltage, clock polarity, configuration pins, output timing, and power sequence. In particular, confirm the CON0 and CON1 operating modes and any dependencies between power-down, standby, and differential configuration.
合规信息
The manufacturer product information confirms an analog-to-digital converter and 28-pin TSSOP package, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive-qualification statement was identified. AEC-Q100 is not applicable because the target is not described as an automotive-qualified ADC.