TJA1021TK/20/C - 20 kBd LIN Transceiver | NXP
MPN: TJA1021TK/20/C ✓ सक्रियTJA1021TK/20/C अवलोकन
A LIN transceiver is a physical-layer interface IC within the broader automotive network-controller hierarchy. A microcontroller or dedicated LIN controller generates serial transmit data, while the transceiver converts that logic-level signal into a waveform suitable for the single-wire LIN bus. It also receives the bus waveform and converts it back into a logic signal that the protocol controller can interpret.
The TJA1021TK/20/C provides optimized slew-rate control and waveform shaping to reduce electromagnetic emissions. It is pin-compatible with the TJA1020 and MC33662B families and has an improved electrostatic-discharge specification relative to the TJA1020. The integrated regulator reduces the external power-supply requirements of the transceiver. Its 20 kBd limit supports modern in-vehicle subnetworks while retaining compatibility with lower LIN baud rates down to 1 kBd.
The /20 variant is intended for LIN networks operating at rates up to 20 kBd. The HVSON-8 package provides a compact surface-mount footprint and an exposed thermal pad for heat dissipation. Because a LIN bus is a single-wire network, its transceiver must coordinate transmitter dominance, receiver thresholds, bus termination, waveform control, and fault behavior while allowing multiple nodes to share the same communication channel.
Typical uses include LIN master modules, LIN slave controllers, body-control modules, door modules, seat modules, climate-control interfaces, switch panels, automotive lighting controllers, and other low-speed vehicle subnetworks. The part is particularly suitable where compact placement, standardized LIN behavior, low electromagnetic emissions, and direct compatibility with existing TJA1020-class hardware are important.
Design the LIN bus according to the NXP datasheet, including the specified transceiver input and output capacitors, bus termination, pull-up arrangement, wiring topology, and exposed-pad soldering. Maintain the required headroom between the battery-side supply and the LIN bus level, and validate EMC behavior in the finished vehicle harness because cable geometry and termination can affect edge quality.
This page combines protocol compatibility, package details, verified sourcing information, drop-in alternatives, and practical integration guidance. It also identifies where design data must be checked against the manufacturer datasheet, helping engineers move from component selection to LIN network implementation more efficiently.
के लिए ड्रॉप-इन विकल्प TJA1021TK/20/C — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
TJA1021TK/20/S1Z
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TJA1021TK/20
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TJA1021TK
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TJA1020TK/20/C
✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TJA1021TK/20/C विशेषताएं
| Product Type | LIN bus transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Minimum Communication Rate | 1 kBd |
| Maximum Communication Rate | 20 kBd |
| LIN Compatibility | LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A |
| Automotive Standards | SAE J2602 and ISO 17987-4:2016 |
| Integrated Voltage Regulator | Yes |
| Transmit Slew-Rate Control | Optimized |
| पैकेज | 8-pin HVSON, 3 x 3 mm |
| माउंटिंग प्रकार | Surface mount |
| Exposed Thermal Pad | Yes |
| Automotive Qualification | AEC-Q100 |
| TJA1020 Pin Compatibility | Pin-compatible |
| MC33662B Pin Compatibility | Pin-compatible |
TJA1021TK/20/C 8-pin hvson, 3 x 3 mm पिन कॉन्फ़िगरेशन गाइड
TJA1021TK/20/C (8-pin hvson, 3 x 3 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। पिन नंबरिंग, फ़ंक्शन और कनेक्शन आरेख निर्माता डेटाशीट में परिभाषित हैं। सटीक फुटप्रिंट और सोल्डरिंग दिशानिर्देशों के लिए इसे देखें।
इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: TJA1021TK/20/C.
देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।
सामान्य अनुप्रयोग
TJA1021TK/20/C के लिए उपयुक्त है 6 अनुप्रयोगs: Automotive LIN Master Module, Door and Seat Control Module, Body Control Gateway, Automotive Climate-Control Interface, Automotive Switch and Lighting Controller, LIN Diagnostics and Test Fixture.
Automotive LIN Master Module
The TJA1021TK/20/C fits a LIN master interface because it converts controller transmit data into a controlled LIN bus waveform and returns received bus data to the protocol controller. Its 1 kBd to 20 kBd operating range covers standard in-vehicle LIN subnetworks, while optimized slew-rate control is intended to reduce electromagnetic emissions. The 3 x 3 mm HVSON-8 footprint supports compact controller boards, and its documented TJA1020 compatibility can simplify upgrades of existing master modules. The final design must follow the manufacturer application circuit for supply decoupling, exposed-pad grounding, bus pull-up and termination arrangements, and EMC validation in the vehicle harness.
अनुशंसित
Door and Seat Control Module
A door or seat control module can use the TJA1021TK/20/C when it must communicate with other vehicle nodes over a single-wire LIN subnet. The device's 20 kBd maximum rate is suitable for typical LIN command and diagnostic traffic, while its compact 3 x 3 mm package leaves board area for sensors, switch inputs, and local actuation electronics. Optimized wave shaping helps control emissions from a cable-connected module, and the integrated regulator simplifies the transceiver power architecture. Place the device and its supporting capacitors near the LIN connector, observe the prescribed bus termination and pull-up topology, and validate threshold behavior and ESD protection against the vehicle harness requirements.
अनुशंसित
Body Control Gateway
The TJA1021TK/20/C can serve as a LIN gateway or branch interface in a body-control module that connects switches, lamps, locks, and climate functions to a larger vehicle network. Its support for LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 allows integration with established vehicle communication specifications. The 20 kBd capability supports the stated LIN subnet range, and the controlled transmitter edge rate is beneficial for reducing electromagnetic emissions. The small HVSON-8 package allows placement near the harness connection, but PCB layout must preserve a short return path, provide the specified exposed-pad solder fill, and follow the manufacturer's bus-component recommendations.
अनुशंसित
Automotive Climate-Control Interface
The TJA1021TK/20/C is suitable for a climate-control panel or HVAC interface that exchanges button, motor, and sensor commands over a LIN subnet. The transceiver operates from 1 kBd to 20 kBd, giving designers flexibility within the supported LIN specification range, while its small 3 x 3 mm footprint is useful where the enclosure contains a dense user-interface board. Optimized slew-rate control helps limit radiated emissions from long wiring runs, and the integrated regulator supports a compact power implementation. Use the manufacturer datasheet to select the LIN bus pull-up and termination arrangement, connect the exposed thermal pad correctly, and test operation across vehicle supply transients and temperature limits.
अनुशंसित
Automotive Switch and Lighting Controller
A distributed switch-pack or lighting controller can use the TJA1021TK/20/C to connect switches, indicators, or lamps to a LIN subnet. The 20 kBd limit accommodates the device's specified LIN operating range, and the transmitter's optimized wave shaping helps reduce electromagnetic emissions from board traces and vehicle cables. Pin compatibility with the TJA1020 family provides a practical path for updating hardware that already uses that interface. Keep the transceiver close to the cable entry, minimize the loop area of bus and return connections, implement the manufacturer's recommended capacitor network, and confirm the exposed-pad connection and reflow profile before production release.
अनुशंसित
LIN Diagnostics and Test Fixture
The TJA1021TK/20/C can be used in a LIN interface test fixture or diagnostic adapter that must emulate or monitor a vehicle LIN subnet. Supporting baud rates from 1 kBd to 20 kBd allows the fixture to test multiple LIN operating rates, while standard compatibility covers LIN 2.x and the cited automotive specifications. The controlled transmitter waveform improves signal consistency, and the small HVSON-8 package makes the interface suitable for compact test equipment. For reliable measurements, follow the datasheet's pin, capacitance, pull-up, and termination guidance, account for probe loading at the bus, and include testing across supply, temperature, fault-recovery, and electromagnetic-emission conditions.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा TJA1021TK/20/C — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | TJA1021TK/20/S1Z | TJA1021TK/20 | TJA1021TK | TJA1020TK/20/C |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) |
| Maximum Baud Rate | 20 kBd | 20 kBd | 20 kBd | 20 kBd | 20 kBd |
| TJA1020 Pin Compatibility | Yes | Yes | Yes | Yes | Yes |
| ESD Position | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Original TJA1020-generation ESD specification |
मुख्य विशेषताएँ
- Supports the full stated 20 kBd LIN range while retaining 1 kBd operation (बनामTJA1020TK/20/C)
- Improved electrostatic-discharge specification (बनामTJA1020TK/20/C)
- Optimized transmitter waveform for lower electromagnetic emissions (बनामTJA1021TK/20/S1Z)
- Compact 3 x 3 mm HVSON-8 footprint (बनामTJA1021T)
डिज़ाइन नोट्स
Place the TJA1021TK/20/C close to the LIN connector and route the bus conductor as a short, controlled-impedance path on the PCB. Maintain the return-current path and minimize loop area to reduce radiated emissions. Follow the NXP datasheet for the recommended input and output capacitors, bus pull-up, termination, and exposed-pad land pattern. The 3 x 3 mm HVSON-8 package also requires careful stencil design and sufficient solder fill under the exposed thermal pad.
Use the manufacturer's optimized slew-rate and wave-shaping implementation without adding arbitrary series resistance or filtering that could distort LIN communication. EMI performance depends on both the transceiver and the vehicle harness, so verify the complete module with its cable, connector, chassis return, and neighboring electronic systems. Check transmitter edge quality, bus thresholds, and radiated emissions at every intended baud rate from 1 kBd through 20 kBd.
Do not treat the TJA1021TK/20/C and TJA1020TK/20/C as automatically interchangeable in every production program. Although the manufacturer identifies pin compatibility, check the exact ordering code, ESD rating, qualification, supply limits, sleep behavior, and application timing. Also distinguish the 8-HVSON package from other TJA1021 package options before substituting; a shared protocol function does not guarantee a shared PCB footprint.
The integrated regulator does not eliminate the need for correct local power implementation. Use the manufacturer-specified supply range, bypass capacitors, grounding arrangement, and exposed-pad connection. Place decoupling components close to their associated pins, keep high-current return currents out of sensitive transceiver areas, and test startup, sleep, wake-up, and fault-recovery behavior across the complete vehicle supply and temperature environment.
अनुपालन जानकारी
The manufacturer product documentation identifies the device as an AEC-Q100 automotive LIN transceiver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited product records.