TJA1021TK/20/C - 20 kBd LIN Transceiver | NXP
料号: TJA1021TK/20/C ✓ 量产中TJA1021TK/20/C 概述
A LIN transceiver is a physical-layer interface IC within the broader automotive network-controller hierarchy. A microcontroller or dedicated LIN controller generates serial transmit data, while the transceiver converts that logic-level signal into a waveform suitable for the single-wire LIN bus. It also receives the bus waveform and converts it back into a logic signal that the protocol controller can interpret.
The TJA1021TK/20/C provides optimized slew-rate control and waveform shaping to reduce electromagnetic emissions. It is pin-compatible with the TJA1020 and MC33662B families and has an improved electrostatic-discharge specification relative to the TJA1020. The integrated regulator reduces the external power-supply requirements of the transceiver. Its 20 kBd limit supports modern in-vehicle subnetworks while retaining compatibility with lower LIN baud rates down to 1 kBd.
The /20 variant is intended for LIN networks operating at rates up to 20 kBd. The HVSON-8 package provides a compact surface-mount footprint and an exposed thermal pad for heat dissipation. Because a LIN bus is a single-wire network, its transceiver must coordinate transmitter dominance, receiver thresholds, bus termination, waveform control, and fault behavior while allowing multiple nodes to share the same communication channel.
Typical uses include LIN master modules, LIN slave controllers, body-control modules, door modules, seat modules, climate-control interfaces, switch panels, automotive lighting controllers, and other low-speed vehicle subnetworks. The part is particularly suitable where compact placement, standardized LIN behavior, low electromagnetic emissions, and direct compatibility with existing TJA1020-class hardware are important.
Design the LIN bus according to the NXP datasheet, including the specified transceiver input and output capacitors, bus termination, pull-up arrangement, wiring topology, and exposed-pad soldering. Maintain the required headroom between the battery-side supply and the LIN bus level, and validate EMC behavior in the finished vehicle harness because cable geometry and termination can affect edge quality.
This page combines protocol compatibility, package details, verified sourcing information, drop-in alternatives, and practical integration guidance. It also identifies where design data must be checked against the manufacturer datasheet, helping engineers move from component selection to LIN network implementation more efficiently.
直接替换替代料: TJA1021TK/20/C ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TJA1021TK/20/S1Z
✅ 直接替换📋 参考替代料(不在目录中)
TJA1021TK/20
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1021TK
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1020TK/20/C
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TJA1021TK/20/C 规格参数
| Product Type | LIN bus transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Minimum Communication Rate | 1 kBd |
| Maximum Communication Rate | 20 kBd |
| LIN Compatibility | LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A |
| Automotive Standards | SAE J2602 and ISO 17987-4:2016 |
| Integrated Voltage Regulator | Yes |
| Transmit Slew-Rate Control | Optimized |
| 封装 | 8-pin HVSON, 3 x 3 mm |
| 安装类型 | Surface mount |
| Exposed Thermal Pad | Yes |
| Automotive Qualification | AEC-Q100 |
| TJA1020 Pin Compatibility | Pin-compatible |
| MC33662B Pin Compatibility | Pin-compatible |
TJA1021TK/20/C 8-pin hvson, 3 x 3 mm 引脚配置指南
TJA1021TK/20/C(8-pin hvson, 3 x 3 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1021TK/20/C.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1021TK/20/C 适用于 6 应用s: Automotive LIN Master Module, Door and Seat Control Module, Body Control Gateway, Automotive Climate-Control Interface, Automotive Switch and Lighting Controller, LIN Diagnostics and Test Fixture.
Automotive LIN Master Module
The TJA1021TK/20/C fits a LIN master interface because it converts controller transmit data into a controlled LIN bus waveform and returns received bus data to the protocol controller. Its 1 kBd to 20 kBd operating range covers standard in-vehicle LIN subnetworks, while optimized slew-rate control is intended to reduce electromagnetic emissions. The 3 x 3 mm HVSON-8 footprint supports compact controller boards, and its documented TJA1020 compatibility can simplify upgrades of existing master modules. The final design must follow the manufacturer application circuit for supply decoupling, exposed-pad grounding, bus pull-up and termination arrangements, and EMC validation in the vehicle harness.
推荐
Door and Seat Control Module
A door or seat control module can use the TJA1021TK/20/C when it must communicate with other vehicle nodes over a single-wire LIN subnet. The device's 20 kBd maximum rate is suitable for typical LIN command and diagnostic traffic, while its compact 3 x 3 mm package leaves board area for sensors, switch inputs, and local actuation electronics. Optimized wave shaping helps control emissions from a cable-connected module, and the integrated regulator simplifies the transceiver power architecture. Place the device and its supporting capacitors near the LIN connector, observe the prescribed bus termination and pull-up topology, and validate threshold behavior and ESD protection against the vehicle harness requirements.
推荐
Body Control Gateway
The TJA1021TK/20/C can serve as a LIN gateway or branch interface in a body-control module that connects switches, lamps, locks, and climate functions to a larger vehicle network. Its support for LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 allows integration with established vehicle communication specifications. The 20 kBd capability supports the stated LIN subnet range, and the controlled transmitter edge rate is beneficial for reducing electromagnetic emissions. The small HVSON-8 package allows placement near the harness connection, but PCB layout must preserve a short return path, provide the specified exposed-pad solder fill, and follow the manufacturer's bus-component recommendations.
推荐
Automotive Climate-Control Interface
The TJA1021TK/20/C is suitable for a climate-control panel or HVAC interface that exchanges button, motor, and sensor commands over a LIN subnet. The transceiver operates from 1 kBd to 20 kBd, giving designers flexibility within the supported LIN specification range, while its small 3 x 3 mm footprint is useful where the enclosure contains a dense user-interface board. Optimized slew-rate control helps limit radiated emissions from long wiring runs, and the integrated regulator supports a compact power implementation. Use the manufacturer datasheet to select the LIN bus pull-up and termination arrangement, connect the exposed thermal pad correctly, and test operation across vehicle supply transients and temperature limits.
推荐
Automotive Switch and Lighting Controller
A distributed switch-pack or lighting controller can use the TJA1021TK/20/C to connect switches, indicators, or lamps to a LIN subnet. The 20 kBd limit accommodates the device's specified LIN operating range, and the transmitter's optimized wave shaping helps reduce electromagnetic emissions from board traces and vehicle cables. Pin compatibility with the TJA1020 family provides a practical path for updating hardware that already uses that interface. Keep the transceiver close to the cable entry, minimize the loop area of bus and return connections, implement the manufacturer's recommended capacitor network, and confirm the exposed-pad connection and reflow profile before production release.
推荐
LIN Diagnostics and Test Fixture
The TJA1021TK/20/C can be used in a LIN interface test fixture or diagnostic adapter that must emulate or monitor a vehicle LIN subnet. Supporting baud rates from 1 kBd to 20 kBd allows the fixture to test multiple LIN operating rates, while standard compatibility covers LIN 2.x and the cited automotive specifications. The controlled transmitter waveform improves signal consistency, and the small HVSON-8 package makes the interface suitable for compact test equipment. For reliable measurements, follow the datasheet's pin, capacitance, pull-up, and termination guidance, account for probe loading at the bus, and include testing across supply, temperature, fault-recovery, and electromagnetic-emission conditions.
推荐
推荐产品汇总
工程参考数据: TJA1021TK/20/C ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1021TK/20/S1Z | TJA1021TK/20 | TJA1021TK | TJA1020TK/20/C |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) | 8-HVSON (3 x 3 mm) |
| Maximum Baud Rate | 20 kBd | 20 kBd | 20 kBd | 20 kBd | 20 kBd |
| TJA1020 Pin Compatibility | Yes | Yes | Yes | Yes | Yes |
| ESD Position | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Improved ESD specification versus TJA1020 | Original TJA1020-generation ESD specification |
关键差异点
- Supports the full stated 20 kBd LIN range while retaining 1 kBd operation (对比 TJA1020TK/20/C)
- Improved electrostatic-discharge specification (对比 TJA1020TK/20/C)
- Optimized transmitter waveform for lower electromagnetic emissions (对比 TJA1021TK/20/S1Z)
- Compact 3 x 3 mm HVSON-8 footprint (对比 TJA1021T)
设计说明
Place the TJA1021TK/20/C close to the LIN connector and route the bus conductor as a short, controlled-impedance path on the PCB. Maintain the return-current path and minimize loop area to reduce radiated emissions. Follow the NXP datasheet for the recommended input and output capacitors, bus pull-up, termination, and exposed-pad land pattern. The 3 x 3 mm HVSON-8 package also requires careful stencil design and sufficient solder fill under the exposed thermal pad.
Use the manufacturer's optimized slew-rate and wave-shaping implementation without adding arbitrary series resistance or filtering that could distort LIN communication. EMI performance depends on both the transceiver and the vehicle harness, so verify the complete module with its cable, connector, chassis return, and neighboring electronic systems. Check transmitter edge quality, bus thresholds, and radiated emissions at every intended baud rate from 1 kBd through 20 kBd.
Do not treat the TJA1021TK/20/C and TJA1020TK/20/C as automatically interchangeable in every production program. Although the manufacturer identifies pin compatibility, check the exact ordering code, ESD rating, qualification, supply limits, sleep behavior, and application timing. Also distinguish the 8-HVSON package from other TJA1021 package options before substituting; a shared protocol function does not guarantee a shared PCB footprint.
The integrated regulator does not eliminate the need for correct local power implementation. Use the manufacturer-specified supply range, bypass capacitors, grounding arrangement, and exposed-pad connection. Place decoupling components close to their associated pins, keep high-current return currents out of sensitive transceiver areas, and test startup, sleep, wake-up, and fault-recovery behavior across the complete vehicle supply and temperature environment.
合规信息
The manufacturer product documentation identifies the device as an AEC-Q100 automotive LIN transceiver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited product records.