NXP Semiconductors

TJA1021TK/20/C - 20 kBd LIN Transceiver | NXP

MPN: TJA1021TK/20/C ✓ فعال
Yes Vdss SAE J2602 and ISO 17987-4:2016 Rds(on) 8-pin HVSON, 3 x 3 mm Package
حداقل سفارش: 1 |

TJA1021TK/20/C نمای کلی

The NXP TJA1021TK/20/C is an automotive LIN physical-layer transceiver supporting communication from 1 kBd to 20 kBd in an 8-pin HVSON package measuring 3 x 3 mm. It interfaces a LIN commander or responder protocol controller with the physical LIN bus, integrates a voltage regulator, and supports LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 communication.

A LIN transceiver is a physical-layer interface IC within the broader automotive network-controller hierarchy. A microcontroller or dedicated LIN controller generates serial transmit data, while the transceiver converts that logic-level signal into a waveform suitable for the single-wire LIN bus. It also receives the bus waveform and converts it back into a logic signal that the protocol controller can interpret.

The TJA1021TK/20/C provides optimized slew-rate control and waveform shaping to reduce electromagnetic emissions. It is pin-compatible with the TJA1020 and MC33662B families and has an improved electrostatic-discharge specification relative to the TJA1020. The integrated regulator reduces the external power-supply requirements of the transceiver. Its 20 kBd limit supports modern in-vehicle subnetworks while retaining compatibility with lower LIN baud rates down to 1 kBd.

The /20 variant is intended for LIN networks operating at rates up to 20 kBd. The HVSON-8 package provides a compact surface-mount footprint and an exposed thermal pad for heat dissipation. Because a LIN bus is a single-wire network, its transceiver must coordinate transmitter dominance, receiver thresholds, bus termination, waveform control, and fault behavior while allowing multiple nodes to share the same communication channel.

Typical uses include LIN master modules, LIN slave controllers, body-control modules, door modules, seat modules, climate-control interfaces, switch panels, automotive lighting controllers, and other low-speed vehicle subnetworks. The part is particularly suitable where compact placement, standardized LIN behavior, low electromagnetic emissions, and direct compatibility with existing TJA1020-class hardware are important.

Design the LIN bus according to the NXP datasheet, including the specified transceiver input and output capacitors, bus termination, pull-up arrangement, wiring topology, and exposed-pad soldering. Maintain the required headroom between the battery-side supply and the LIN bus level, and validate EMC behavior in the finished vehicle harness because cable geometry and termination can affect edge quality.

This page combines protocol compatibility, package details, verified sourcing information, drop-in alternatives, and practical integration guidance. It also identifies where design data must be checked against the manufacturer datasheet, helping engineers move from component selection to LIN network implementation more efficiently.

جایگزین‌های drop-in برای TJA1021TK/20/C — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

TJA1021TK/20/S1Z

✅ جایگزین مستقیم
📦 8-HVSON (3 x 3 mm)
Maximum LIN rate remains 20 kBd, a 0% baud-rate difference; the S1Z is a separately ordered NXP qualification or ordering variant requiring order-code review.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021TK/20

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3 x 3 mm)
Supports the same 1 kBd to 20 kBd LIN range for a 0% maximum-rate difference, while omitting the C suffix used by the target ordering code.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021TK

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3 x 3 mm)
Provides the same 1 kBd to 20 kBd communication capability, a 0% maximum-rate difference, and pin-compatible TJA1020-class integration.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1020TK/20/C

✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده
📦 8-HVSON (3 x 3 mm)
Supports the same 20 kBd maximum rate and is pin-compatible; the TJA1021 generation has an improved ESD specification, although the numeric ESD rating must be checked in each datasheet.

📋 جایگزین مرجع (خارج از کاتالوگ)

TJA1021TK/20/C مشخصات

Product Type LIN bus transceiver
Transceiver Configuration 1 transmitter and 1 receiver
Minimum Communication Rate 1 kBd
Maximum Communication Rate 20 kBd
LIN Compatibility LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A
Automotive Standards SAE J2602 and ISO 17987-4:2016
Integrated Voltage Regulator Yes
Transmit Slew-Rate Control Optimized
بسته‌بندی 8-pin HVSON, 3 x 3 mm
نوع نصب Surface mount
Exposed Thermal Pad Yes
Automotive Qualification AEC-Q100
TJA1020 Pin Compatibility Pin-compatible
MC33662B Pin Compatibility Pin-compatible

راهنمای پیکربندی پین TJA1021TK/20/C 8-pin hvson, 3 x 3 mm

پیکربندی پین برای TJA1021TK/20/C (پکیج 8-pin hvson, 3 x 3 mm). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 8-pin hvson, 3 x 3 mm برای TJA1021TK/20/C

داده پین‌آوت تفصیلی موجود نیست برای TJA1021TK/20/C.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

TJA1021TK/20/C مناسب است برای 6 کاربردs: Automotive LIN Master Module, Door and Seat Control Module, Body Control Gateway, Automotive Climate-Control Interface, Automotive Switch and Lighting Controller, LIN Diagnostics and Test Fixture.

🚗

Automotive LIN Master Module

The TJA1021TK/20/C fits a LIN master interface because it converts controller transmit data into a controlled LIN bus waveform and returns received bus data to the protocol controller. Its 1 kBd to 20 kBd operating range covers standard in-vehicle LIN subnetworks, while optimized slew-rate control is intended to reduce electromagnetic emissions. The 3 x 3 mm HVSON-8 footprint supports compact controller boards, and its documented TJA1020 compatibility can simplify upgrades of existing master modules. The final design must follow the manufacturer application circuit for supply decoupling, exposed-pad grounding, bus pull-up and termination arrangements, and EMC validation in the vehicle harness.

🚗

Door and Seat Control Module

A door or seat control module can use the TJA1021TK/20/C when it must communicate with other vehicle nodes over a single-wire LIN subnet. The device's 20 kBd maximum rate is suitable for typical LIN command and diagnostic traffic, while its compact 3 x 3 mm package leaves board area for sensors, switch inputs, and local actuation electronics. Optimized wave shaping helps control emissions from a cable-connected module, and the integrated regulator simplifies the transceiver power architecture. Place the device and its supporting capacitors near the LIN connector, observe the prescribed bus termination and pull-up topology, and validate threshold behavior and ESD protection against the vehicle harness requirements.

🏭

Body Control Gateway

The TJA1021TK/20/C can serve as a LIN gateway or branch interface in a body-control module that connects switches, lamps, locks, and climate functions to a larger vehicle network. Its support for LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016 allows integration with established vehicle communication specifications. The 20 kBd capability supports the stated LIN subnet range, and the controlled transmitter edge rate is beneficial for reducing electromagnetic emissions. The small HVSON-8 package allows placement near the harness connection, but PCB layout must preserve a short return path, provide the specified exposed-pad solder fill, and follow the manufacturer's bus-component recommendations.

🧩

Automotive Climate-Control Interface

The TJA1021TK/20/C is suitable for a climate-control panel or HVAC interface that exchanges button, motor, and sensor commands over a LIN subnet. The transceiver operates from 1 kBd to 20 kBd, giving designers flexibility within the supported LIN specification range, while its small 3 x 3 mm footprint is useful where the enclosure contains a dense user-interface board. Optimized slew-rate control helps limit radiated emissions from long wiring runs, and the integrated regulator supports a compact power implementation. Use the manufacturer datasheet to select the LIN bus pull-up and termination arrangement, connect the exposed thermal pad correctly, and test operation across vehicle supply transients and temperature limits.

💡

Automotive Switch and Lighting Controller

A distributed switch-pack or lighting controller can use the TJA1021TK/20/C to connect switches, indicators, or lamps to a LIN subnet. The 20 kBd limit accommodates the device's specified LIN operating range, and the transmitter's optimized wave shaping helps reduce electromagnetic emissions from board traces and vehicle cables. Pin compatibility with the TJA1020 family provides a practical path for updating hardware that already uses that interface. Keep the transceiver close to the cable entry, minimize the loop area of bus and return connections, implement the manufacturer's recommended capacitor network, and confirm the exposed-pad connection and reflow profile before production release.

🔧

LIN Diagnostics and Test Fixture

The TJA1021TK/20/C can be used in a LIN interface test fixture or diagnostic adapter that must emulate or monitor a vehicle LIN subnet. Supporting baud rates from 1 kBd to 20 kBd allows the fixture to test multiple LIN operating rates, while standard compatibility covers LIN 2.x and the cited automotive specifications. The controlled transmitter waveform improves signal consistency, and the small HVSON-8 package makes the interface suitable for compact test equipment. For reliable measurements, follow the datasheet's pin, capacitance, pull-up, and termination guidance, account for probe loading at the bus, and include testing across supply, temperature, fault-recovery, and electromagnetic-emission conditions.

خلاصه محصولات پیشنهادی

TJA1021T Related TJA1021 LIN transceiver family member استفاده‌شده در: Automotive LIN Master Module, Automotive Climate-Control Interface TJA1020 Pin-compatible LIN transceiver family استفاده‌شده در: Automotive LIN Master Module, Door and Seat Control Module, Automotive Climate-Control Interface, LIN Diagnostics and Test Fixture TJA1021TK/20/S1Z Related 20 kBd LIN transceiver ordering option استفاده‌شده در: Door and Seat Control Module, Automotive Switch and Lighting Controller MC33662B Pin-compatible LIN transceiver family استفاده‌شده در: Body Control Gateway, Automotive Switch and Lighting Controller TJA1021TK/20 Related 20 kBd family variant استفاده‌شده در: Body Control Gateway TJA1021TK Related TJA1021 package option استفاده‌شده در: LIN Diagnostics and Test Fixture
What is the TJA1021TK/20/C?
The TJA1021TK/20/C is an NXP automotive LIN physical-layer transceiver that connects a LIN commander or responder controller to a single-wire LIN bus. According to the NXP manufacturer datasheet, the /20 version supports baud rates from 1 kBd to 20 kBd and is compatible with LIN 2.0, LIN 2.1, LIN 2.2, LIN 2.2A, SAE J2602, and ISO 17987-4:2016.
What is the maximum baud rate of the TJA1021TK/20/C?
The TJA1021TK/20/C supports a maximum LIN communication rate of 20 kBd, with operation down to 1 kBd. The NXP manufacturer datasheet identifies the /20 and B variants as 20 kBd-capable devices. This makes the part suitable for established in-vehicle LIN subnetworks, including body, comfort, seat, climate-control, and distributed switch modules.
Where can I download the TJA1021TK/20/C datasheet PDF?
The TJA1021TK/20/C datasheet PDF is available from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1021.pdf. The manufacturer datasheet is the controlling document for the LIN interface, supported standards, electrical limits, pin descriptions, application circuit, and recommended external components. Use it to verify the exact ordering code and package drawing before releasing a PCB design.
Where can I find the TJA1021TK/20/C pinout?
The TJA1021TK/20/C pinout is shown in the manufacturer datasheet under the pin-description and package-information sections. The device uses an 8-pin HVSON package measuring 3 x 3 mm with an exposed thermal pad. Use the datasheet pin table and land pattern when assigning PCB tracks; the exposed pad is a thermal and electrical land feature rather than an additional signal pin.
Is the TJA1021TK/20/C pin-compatible with the TJA1020?
Yes, the TJA1021TK/20/C is pin-compatible with the TJA1020 family, while providing an improved electrostatic-discharge specification according to the NXP manufacturer datasheet. Compatibility supports replacement of an existing TJA1020 implementation without changing the PCB footprint. Confirm device variants, electrical limits, ESD classification, and application requirements before approving the substitution.
Can the TJA1021TK/20/C replace an MC33662B?
The TJA1021TK/20/C is stated to be pin-compatible with the MC33662B family by the NXP manufacturer datasheet. The /20 device also supports rates from 1 kBd to 20 kBd, matching the high-rate LIN use case. Nevertheless, verify supply voltage, pin functions, protection behavior, qualification, and application timing against the specific MC33662B ordering code before making a production substitution.
What is the difference between TJA1021TK/20/C and TJA1021TK/20/S1Z?
Both parts are NXP 20 kBd LIN transceivers in the 8-pin HVSON package and use the TJA1021TK/20 product family. The available product records identify TJA1021TK/20/S1Z as a separately ordered variant, while the C suffix identifies the TJA1021TK/20/C,118 ordering code. The exact lifecycle, qualification, and order-code differences should be confirmed from the NXP product documentation.
When should I choose TJA1021TK/20/C over TJA1020?
Choose the TJA1021TK/20/C when an existing LIN design uses a compatible TJA1020 footprint and requires the newer transceiver's improved electrostatic-discharge specification. Both devices support the same 20 kBd LIN use case and provide pin compatibility. Select the older TJA1020 only when an existing platform, qualification record, or long-term sourcing plan requires it.
What is the best drop-in replacement for TJA1021TK/20/C?
The closest documented drop-in choice is another compatible TJA1021TK/20-family ordering code in the same 8-pin HVSON package, subject to order-code and qualification review. The NXP product page identifies pin compatibility with the TJA1020 and MC33662B families, but it does not establish every alternative as a production-approved replacement. Compare the manufacturer datasheets and complete an application-level review before substitution.
Is TJA1021TK/20/C suitable for an automotive LIN bus?
The TJA1021TK/20/C is intended for in-vehicle LIN subnetworks and is identified as an AEC-Q100 automotive device. The NXP manufacturer datasheet lists support for LIN 2.0 through LIN 2.2A, SAE J2602, and ISO 17987-4:2016 at rates from 1 kBd to 20 kBd. Its optimized slew-rate control and waveform shaping are intended to reduce electromagnetic emissions in vehicle electrical environments.
How does the TJA1021TK/20/C reduce electromagnetic emissions?
The TJA1021TK/20/C converts the controller's transmit data into a LIN bus signal using optimized slew-rate control and wave shaping. The NXP manufacturer datasheet states that this technique helps minimize electromagnetic emission. Actual EMC performance also depends on PCB placement, the bus cable, termination, node layout, filtering, and vehicle harness, so conduct system-level testing in the final installation.
Does the TJA1021TK/20/C include a voltage regulator?
Yes, the TJA1021TK/20/C includes an integrated voltage regulator for its internal transceiver functions. The NXP product documentation identifies the integrated regulator as part of the device architecture. Use the manufacturer datasheet for the permitted external-supply range, capacitor requirements, grounding, exposed-pad connection, and power-consumption conditions rather than assuming a conventional 3.3 V or 5 V supply.
How should the 3 x 3 mm HVSON package be soldered?
Follow the NXP datasheet's reflow profile, land pattern, stencil recommendations, and exposed-pad soldering instructions. The 3 x 3 mm HVSON-8 has limited thermal dissipation area, so the exposed pad should be connected to the recommended ground or thermal land with adequate copper and solder fill. Inspect for voids and keep paste and solder-cleaning processes compatible with the package's fine pitch.
Where can I buy TJA1021TK/20/C online?
Use the Request a Quote form on this page to request the TJA1021TK/20/C, current unit availability, lot-size pricing, and lead time. The form allows buyers to specify quantity and obtain a current sourcing response without relying on static catalog pricing. Confirm the exact TJA1021TK/20/C,118 ordering code, reel packaging, and delivery requirements with the supplier.
What is the lead time and stock status of TJA1021TK/20/C?
Current stock and lead time for the TJA1021TK/20/C should be requested through the Request a Quote form on this page. Enter the required quantity, reel or delivery format, production date, and destination so the supplier can confirm the appropriate schedule. Do not infer current availability from general family listings because exact order codes and package variants can have different stocking positions.

داده‌های مرجع مهندسی برای TJA1021TK/20/C — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TJA1021TK/20/C for a 20 kBd-class LIN interface that uses the 8-pin HVSON 3 x 3 mm footprint, especially when replacing a compatible TJA1020 design and gaining the newer generation's improved ESD specification. TJA1021TK/20/S1Z is the closest separately documented ordering option in the same package, but its order-code or qualification differences must be reviewed. TJA1021TK/20 and TJA1021TK provide the same documented 1 kBd to 20 kBd family capability and can be considered when the selected NXP ordering code matches the system requirements. TJA1020TK/20/C remains relevant for platforms already standardized on the older TJA1020. None of these choices should be made solely from the protocol name: verify the package drawing, electrical limits, qualification, sleep behavior, lifecycle, and supply conditions before substitution.

مقایسه با جایگزین‌ها

پارامتر این محصول TJA1021TK/20/S1Z TJA1021TK/20 TJA1021TK TJA1020TK/20/C
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm) 8-HVSON (3 x 3 mm)
Maximum Baud Rate 20 kBd 20 kBd 20 kBd 20 kBd 20 kBd
TJA1020 Pin Compatibility Yes Yes Yes Yes Yes
ESD Position Improved ESD specification versus TJA1020 Improved ESD specification versus TJA1020 Improved ESD specification versus TJA1020 Improved ESD specification versus TJA1020 Original TJA1020-generation ESD specification

تفاوت‌های کلیدی

  • Supports the full stated 20 kBd LIN range while retaining 1 kBd operation (در مقابلTJA1020TK/20/C)
  • Improved electrostatic-discharge specification (در مقابلTJA1020TK/20/C)
  • Optimized transmitter waveform for lower electromagnetic emissions (در مقابلTJA1021TK/20/S1Z)
  • Compact 3 x 3 mm HVSON-8 footprint (در مقابلTJA1021T)

یادداشت‌های طراحی

Place the TJA1021TK/20/C close to the LIN connector and route the bus conductor as a short, controlled-impedance path on the PCB. Maintain the return-current path and minimize loop area to reduce radiated emissions. Follow the NXP datasheet for the recommended input and output capacitors, bus pull-up, termination, and exposed-pad land pattern. The 3 x 3 mm HVSON-8 package also requires careful stencil design and sufficient solder fill under the exposed thermal pad.

Use the manufacturer's optimized slew-rate and wave-shaping implementation without adding arbitrary series resistance or filtering that could distort LIN communication. EMI performance depends on both the transceiver and the vehicle harness, so verify the complete module with its cable, connector, chassis return, and neighboring electronic systems. Check transmitter edge quality, bus thresholds, and radiated emissions at every intended baud rate from 1 kBd through 20 kBd.

Do not treat the TJA1021TK/20/C and TJA1020TK/20/C as automatically interchangeable in every production program. Although the manufacturer identifies pin compatibility, check the exact ordering code, ESD rating, qualification, supply limits, sleep behavior, and application timing. Also distinguish the 8-HVSON package from other TJA1021 package options before substituting; a shared protocol function does not guarantee a shared PCB footprint.

The integrated regulator does not eliminate the need for correct local power implementation. Use the manufacturer-specified supply range, bypass capacitors, grounding arrangement, and exposed-pad connection. Place decoupling components close to their associated pins, keep high-current return currents out of sensitive transceiver areas, and test startup, sleep, wake-up, and fault-recovery behavior across the complete vehicle supply and temperature environment.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer product documentation identifies the device as an AEC-Q100 automotive LIN transceiver. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not stated in the cited product records.

تاریخ تأیید داده‌ها: 2026-11-18 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

TJA1021TK/20/C datasheet TJA1021TK/20/C pinout TJA1021TK/20/C datasheet pdf NXP TJA1021TK/20/C TJA1021TK/20/C 20 kBd TJA1021TK/20/C HVSON-8 TJA1021TK/20/C automotive LIN TJA1021TK/20/C equivalent TJA1021TK/20/C replacement TJA1021TK/20/C vs TJA1020TK/20/C TJA1021TK/20/C price TJA1021TK/20/C stock TJA1021TK/20/C application circuit TJA1021TK/20/C vs TJA1021TK/20/S1Z

قطعات و اصطلاحات مرتبط

NXP Semiconductors TJA1021TK/20/C TJA1021TK/20/S1Z TJA1021TK/20 TJA1021TK TJA1020TK/20/C TJA1020 MC33662B LIN transceiver physical-layer interface IC automotive network interface single-wire LIN bus LIN 2.0 LIN 2.1 LIN 2.2 LIN 2.2A SAE J2602 ISO 17987-4:2016 AEC-Q100 optimized slew-rate control electrostatic discharge integrated voltage regulator 8-HVSON 3 x 3 mm surface-mount package
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ