Texas Instruments

TLV2475IN - 2.8MHz Quad R-R Op Amp | Texas Instruments

MPN: TLV2475IN ✓ सक्रिय
600 uA Vdss 2.5 pA Id 16-pin PDIP, 0.300 in (7.62 mm) row spacing Package
न्यूनतम ऑर्डर मात्रा: 1 |

TLV2475IN अवलोकन

The Texas Instruments TLV2475IN is a quad, rail-to-rail input and output CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, 600 uA supply current per channel, and a shutdown function, housed in a 16-pin PDIP package.

A rail-to-rail input and output operational amplifier is a voltage amplifier whose input common-mode range and output swing extend close to both supply rails. This makes it suitable for low-voltage systems in which signals may approach the positive or negative rail. Within the TLV247x family hierarchy, the TLV2475IN is a precision CMOS amplifier within the broader category of operational amplifiers and analog signal-chain ICs.

The principal specifications are a 2.8 MHz gain-bandwidth product, approximately 600 uA of quiescent current per channel, and a typical input bias current of 2.5 pA. The device operates from a nominal 2.7 V to 6 V supply range, with an extended output swing of approximately -1.35 V to +3 V. Each of the four amplifier channels also supports shutdown, allowing unused sections to be disabled when system power management is required.

The CMOS input stage supports high input impedance and low bias current, while the rail-to-rail output stage provides useful drive for sensor signals, filtering, and low-level analog processing. The 2.8 MHz gain-bandwidth product makes the amplifier appropriate for general-purpose signal conditioning, audio-frequency filtering, transducer interfaces, and feedback control loops rather than only static precision measurements.

Typical uses include battery-powered sensor conditioning, four-channel data acquisition, photodiode and phototransistor interfaces, active filters, audio preamplification, and industrial control systems operating from a single low-voltage rail. The shutdown feature can reduce consumption in portable equipment when only part of the quad amplifier is needed.

When laying out the circuit, place input-referred decoupling capacitors close to the supply pins and route sensitive input and feedback traces away from switching nodes. Confirm output settling against the selected closed-loop gain and check the shutdown logic polarity in the manufacturer datasheet before designing a power-sequencing scheme.

This page combines the manufacturer device specifications with package, application, comparison, and design guidance. It also identifies same-family drop-in candidates in the same 16-pin PDIP footprint, making it easier to plan a replacement without changing the printed circuit board.

के लिए ड्रॉप-इन विकल्प TLV2475IN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं TLV2475IN (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type.

Texas Instruments
Amplifier Type: Quad CMOS operational amplifier
इसके साथ तुलना करें TLV2475IN →

TLV2475AIN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 16-pin PDIP (PDIP-16)
Automotive-grade ordering option versus the standard commercial grade; core amplifier ratings remain the same TLV2475 family performance

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2474IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 16-pin PDIP (PDIP-16)
Quad CMOS operational amplifier · 4 channels · 6 V · 2.8 MHz · 600 uA · Rail-to-rail · Rail-to-rail · CMOS

कीमत के लिए संपर्क करें

डेटाशीट देखें →

TLV2472IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 16-pin PDIP (PDIP-16)
Lower gain-bandwidth product than the TLV2475IN while retaining the 16-pin PDIP footprint and low-power CMOS architecture

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2471IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 16-pin PDIP (PDIP-16)
Lower gain-bandwidth product than the TLV2475IN while retaining the 16-pin PDIP footprint and low-power CMOS architecture

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2477IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 16-pin PDIP (PDIP-16)
Lower gain-bandwidth product than the TLV2475IN while retaining the 16-pin PDIP footprint and low-power CMOS architecture

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2475IN Maximum Ratings और Electrical Characteristics

Amplifier Type Quad operational amplifier
Number of Channels 4 channels
Gain-Bandwidth Product 2.8 MHz
Supply Current per Channel 600 uA
Typical Input Bias Current 2.5 pA
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Nominal Supply Voltage 2.7 V to 6 V
Extended Output Swing -1.35 V to +3 V
Typical Output Current per Channel 35 mA
Open-Loop Gain 64 dB
Shutdown Control Yes, one control for four amplifiers
पैकेज 16-pin PDIP, 0.300 in (7.62 mm) row spacing
माउंटिंग प्रकार Through-hole

TLV2475IN 16-pin pdip, 0.300 in (7.62 mm) row spacing पिन कॉन्फ़िगरेशन गाइड

TLV2475IN (16-pin pdip, 0.300 in (7.62 mm) row spacing पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

TLV2475IN के लिए 16-pin pdip, 0.300 in (7.62 mm) row spacing पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: TLV2475IN.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

TLV2475IN के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Sensor Signal Conditioning, Four-Channel Data Acquisition, Precision Active Filtering, Audio Preamplification, Photodiode Interface, Industrial Control and Feedback Loops.

🧩

Battery-Powered Sensor Signal Conditioning

The TLV2475IN suits low-voltage sensor front ends because its 2.7 V to 6 V operating range and 600 uA-per-channel supply current support portable instrumentation. A typical 2.5 pA typical input bias current minimizes loading on high-impedance sources such as thermistors, capacitive sensors, and resistive dividers. Configure the amplifier as a non-inverting or inverting stage around the sensor, place input biasing close to the device, and use the shutdown control when a duty-cycled measurement can reduce energy use. Rail-to-rail input and output operation allows the conditioned signal to use most of the available supply range, while the 2.8 MHz gain-bandwidth product provides more headroom than required for many slow sensors.

📊

Four-Channel Data Acquisition

The quad TLV2475IN consolidates four analog channels in one 16-pin PDIP package, reducing component count in multi-sensor acquisition systems. Each channel provides a 2.8 MHz gain-bandwidth product, rail-to-rail input and output capability, and approximately 600 uA of supply current, enabling independent signal-conditioning stages for temperature, pressure, position, or current sensing. A practical implementation assigns separate amplifier inputs to each sensor, shares a bypassed supply network, and grounds each channel reference close to its feedback divider. Verify channel-to-channel settling and crosstalk in the final layout, especially when small sensor outputs are amplified at moderate or high closed-loop gains.

🎛️

Precision Active Filtering

The TLV2475IN is appropriate for second-order and higher-order active filters operating in the audio or low-frequency instrumentation range. Its 2.8 MHz gain-bandwidth product provides useful loop gain above the filter cutoff, while rail-to-rail output capability supports direct coupling to a following ADC or measurement stage. Set component values from the desired pole and quality factor, then check closed-loop stability and gain error in the manufacturer datasheet for the selected noise-gain configuration. Keep feedback resistors and capacitors physically close, maintain symmetry between differential networks, and reserve a quiet ground return for the analog section to limit filter-component noise coupling.

🎧

Audio Preamplification

The TLV2475IN can amplify low-level audio or microphone signals in a single-supply system. Rail-to-rail input handling accepts signals referenced close to ground, while the output stage provides approximately 35 mA of output current per channel for driving a following load stage. The 2.8 MHz gain-bandwidth product is suitable for audio-band amplification rather than ultrasonic applications. Choose a closed-loop gain that keeps the amplifier within its linear-output region, include an input coupling capacitor for single-supply biasing, and place the input network and feedback components away from switching regulators. The shutdown control can disable unused amplifier sections to reduce system consumption.

💡

Photodiode Interface

The low 2.5 pA typical input bias current of the TLV2475IN makes it useful for photodiode and phototransistor interfaces where input leakage can degrade weak signals. A transimpedance configuration converts photocurrent into a measurable voltage, and the 2.8 MHz gain-bandwidth product supports faster measurement loops than the lower-speed TLV247x options. Keep the photodiode and feedback capacitor connections compact, use guarding where leakage matters, and connect the supply-return path directly to the amplifier ground. Evaluate compliance voltage, input capacitance, stability, and signal polarity using the photodiode and amplifier models for the intended light range.

🏭

Industrial Control and Feedback Loops

The TLV2475IN supports low-voltage industrial control loops that require greater bandwidth than a basic comparator-style output but less power than a high-speed amplifier. Its 2.8 MHz gain-bandwidth product provides loop gain across audio and low-frequency control ranges, while approximately 600 uA per channel keeps four-channel designs economical. Use one channel for error amplification and the others for sensor conditioning or actuator drive. Account for the amplifier's output-swing limits and phase margin, and isolate analog returns from high-current switching paths. The shutdown input is useful in staged systems that disable unused analog channels during specific operating modes.

अनुशंसित उत्पादों का सारांश

TLV2475AIN Automotive-grade same-family quad amplifier option उपयोग में: Battery-Powered Sensor Signal Conditioning, Four-Channel Data Acquisition, Audio Preamplification, Industrial Control and Feedback Loops TLV2474IN Texas Instruments उपयोग में: Battery-Powered Sensor Signal Conditioning, Precision Active Filtering, Photodiode Interface TLV2472IN Same-family quad amplifier for lower-bandwidth channels उपयोग में: Four-Channel Data Acquisition, Photodiode Interface TLV2471IN Low-bandwidth same-package alternative for cutoff-limited filters उपयोग में: Precision Active Filtering, Industrial Control and Feedback Loops TLV2477IN Same-family quad amplifier for lower-bandwidth audio paths उपयोग में: Audio Preamplification
What are the key specifications of TLV2475IN that engineers should know?
The TLV2475IN is a quad CMOS operational amplifier with a 2.8 MHz gain-bandwidth product, approximately 600 uA of supply current per channel, and a typical input bias current of 2.5 pA. Texas Instruments describes the device as a 6 V rail-to-rail input and output amplifier with shutdown. It is packaged in a 16-pin PDIP and is intended for low-voltage, low-power analog signal-conditioning systems.
What is the supply voltage range of the TLV2475IN?
The TLV2475IN operates from a 2.7 V to 6 V supply range. Texas Instruments identifies the device as a 6 V quad operational amplifier, while component listings describe its extended output swing as approximately -1.35 V to +3 V under a nominal 5 V supply. Use the manufacturer datasheet for supply-dependent input range, output swing, and shutdown-current curves before finalizing a bias point.
Where can I download the TLV2475IN datasheet PDF?
The official TLV2475 datasheet is available from the Texas Instruments product page at https://www.ti.com/product/TLV2475. That page contains the manufacturer ordering information, device parameters, and downloadable documentation. The TLV2475IN ordering code identifies the 16-pin PDIP configuration, and engineers should use the pin-description table in the manufacturer datasheet when assigning PCB nets.
Where can I find the TLV2475IN pinout?
The TLV2475IN pinout is documented in the pin-configuration section of the Texas Instruments TLV2475 datasheet. The device uses a 16-pin PDIP package with four operational amplifiers, a shutdown control, supply pins, and ground pins. Use the pin-description table in that document for the exact net assignments; the package drawing is also available through the Texas Instruments product page.
Is TLV2475IN rail-to-rail input and output?
Yes, the TLV2475IN has rail-to-rail input and output operation according to the Texas Instruments product description. Rail-to-rail input capability allows the input common-mode voltage to approach the supply limits, while the output stage can swing close to either rail. This is useful in single-supply sensor interfaces where the signal may extend near ground or the positive supply.
What can replace the TLV2475IN without changing the PCB?
The closest same-family replacements are the 16-pin PDIP versions within the Texas Instruments TLV247x family. TLV2475AIN offers the closest electrical match, while TLV2474IN, TLV2472IN, TLV2471IN, and TLV2477IN use the same package family with lower gain-bandwidth options. Confirm pinout, supply limits, shutdown polarity, and stability for the selected gain before approving a substitution.
Is TLV2475IN the same as TLV2475AIN?
The TLV2475IN and TLV2475AIN belong to the same TLV2475 amplifier family and use the same 16-pin PDIP configuration in the ordering options identified for these devices. TLV2475AIN is the automotive-grade ordering option, while TLV2475IN is the standard commercial-grade option. Check the qualified temperature range and automotive qualification requirements before treating them as interchangeable.
What is the best Texas Instruments equivalent for TLV2475IN?
The TLV2475AIN is the closest Texas Instruments alternative because it belongs to the same amplifier family and provides a like-for-like 16-pin PDIP replacement option. It is intended for automotive-grade designs, so it may also carry different qualification or temperature-range expectations than the standard TLV2475IN. Verify those requirements against the manufacturer datasheet before releasing the substitution.
When should I choose TLV2475IN over a lower-speed TLV247x amplifier?
Choose the TLV2475IN when a signal path needs more closed-loop bandwidth than lower-speed family members provide. Its 2.8 MHz gain-bandwidth product supports higher-frequency filtering and tighter control loops, while its roughly 600 uA-per-channel supply current preserves a low-power design point. Select a lower-speed member when the signal bandwidth is modest and the simplest stable implementation matters more.
Is TLV2475IN suitable for battery-powered sensor applications?
Yes, the TLV2475IN is suitable for battery-powered sensor interfaces because it combines a 2.7 V to 6 V supply range with approximately 600 uA of supply current per channel. Its 2.5 pA typical input bias current reduces disturbance to high-impedance sensors. The shutdown function can further control consumption when the amplifier is not continuously required.
Where can I buy TLV2475IN online and what is its price?
The TLV2475IN can be ordered through authorized channels, and XAIPART provides current commercial availability through the Request a Quote form on this page. Submit the required quantity, target packaging, and shipment destination to obtain a current quotation. Use the manufacturer ordering information to confirm the exact 16-pin PDIP device and any permissible alternate packing options.
What is the lead time for TLV2475IN?
Lead time depends on current inventory, order quantity, and the destination requested. Use the Request a Quote form on this page to obtain the current manufacturing and fulfillment position for the TLV2475IN. The Texas Instruments product page lists lifecycle and ordering information, while the quotation request confirms commercial availability for the required quantity.
Is TLV2475IN currently in stock?
Current stock should be confirmed through the Request a Quote form on this page because availability changes with inventory and order volume. The Texas Instruments product page remains the authoritative source for product lifecycle information, and the quotation form captures the exact quantity and delivery requirements needed for a stock commitment.
TLV2475IN vs TLV2474IN - which is better for signal filtering?
The TLV2475IN is the better choice when the filter requires higher closed-loop bandwidth because it provides a 2.8 MHz gain-bandwidth product versus the lower bandwidth of the TLV2474IN. Both belong to the same low-power CMOS family and have comparable rail-to-rail operating characteristics. The TLV2474IN remains appropriate when the signal band is narrow and lower power or simpler settling behavior is preferred.
How should decoupling and PCB layout be handled for TLV2475IN?
Place the supply-bypass capacitors close to the amplifier power pins and connect each bypass capacitor's ground terminal to a low-impedance ground path. Keep input, feedback, and output traces short, and keep them away from fast-switching nodes and digital return currents. Follow the layout and decoupling recommendations in the Texas Instruments TLV2475 datasheet for stable operation at the intended closed-loop gain.

के लिए इंजीनियरिंग संदर्भ डेटा TLV2475IN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TLV2475IN when the design needs four rail-to-rail amplifier channels, a 2.8 MHz gain-bandwidth product, and roughly 600 uA of supply current per channel in a 16-pin PDIP package. Select TLV2475AIN for an automotive-qualified same-family option after confirming the relevant qualification and temperature requirements. TLV2474IN is appropriate when the signal band is narrow and a lower-bandwidth amplifier provides adequate loop gain. TLV2472IN or TLV2471IN suit slower sensor and control applications where minimum power and simple settling are more important than speed. TLV2477IN is the fallback when a lower-bandwidth member is preferred. Before replacing the TLV2475IN, verify the physical pinout, shutdown-control polarity, supply limits, stability at the intended closed-loop gain, output loading, and operating-temperature requirements in the manufacturer datasheet.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TLV2475AIN TLV2474IN TLV2472IN TLV2471IN TLV2477IN
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 16-pin PDIP (PDIP-16) 16-pin PDIP (PDIP-16) 16-pin PDIP (PDIP-16) 16-pin PDIP (PDIP-16) 16-pin PDIP (PDIP-16) 16-pin PDIP (PDIP-16)
Number of Amplifiers 4 4 4 4 4 4
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output
Shutdown Function Yes Yes Yes Yes Yes Yes
Automotive-Grade Option No Yes No No No No

मुख्य विशेषताएँ

  • Higher-bandwidth member of the low-power quad amplifier family (बनामTLV2474IN)
  • Automotive-grade ordering path within the same amplifier family (बनामTLV2475IN)
  • Low-power operation combined with high input impedance (बनामTLV2472IN)

डिज़ाइन नोट्स

Place the supply-bypass capacitors immediately adjacent to the TLV2475IN power pins, and route each capacitor directly to a low-impedance ground plane rather than through a shared narrow trace. Keep input and feedback nets short and isolate them from switching-node copper. Because the amplifier supports rail-to-rail operation, a ground trace that carries load current can shift the effective input reference and reduce accuracy.

Use the shutdown function to disable amplifier channels that are not required, especially in battery-powered equipment. Account for both operating and shutdown current when calculating system power, and ensure the shutdown logic levels remain valid over the complete supply range. The manufacturer datasheet should be used for the shutdown-control truth table and supply-current behavior.

For photodiode, capacitive-sensor, or high-impedance source interfaces, keep the input node physically small and consider guarding to reduce surface leakage. The 2.5 pA typical input bias current is low, but PCB contamination, long traces, and temperature can still affect high-value sources. Validate leakage, settling, and achievable noise performance in the assembled board rather than relying only on ideal simulation values.

Do not assume that equal rail-to-rail input and output ratings guarantee the same usable voltage range at every load. Check output swing, input common-mode range, load current, and closed-loop gain in the Texas Instruments TLV2475 datasheet. Also verify the exact shutdown polarity and the meaning of each package pin before finalizing the schematic or PCB netlist.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The standard TLV2475IN is a commercial-grade device; the automotive-grade ordering option is TLV2475AIN. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.

डेटा सत्यापन तिथि: 2026-11-10 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

TLV2475IN datasheet TLV2475IN pinout TLV2475IN datasheet pdf TLV2475IN specifications TLV2475IN 16 pin PDIP TLV2475IN rail to rail op amp TLV2475IN 2.8 MHz TLV2475IN replacement TLV2475IN equivalent TLV2475IN vs TLV2474IN TLV2475IN sensor amplifier TLV2475IN shutdown function Texas Instruments TLV2475IN TLV2475IN price TLV2475IN stock

संबंधित कंपोनेंट्स और शब्द

Texas Instruments TLV2475IN TLV2475 TLV2475AIN TLV2474IN TLV2472IN TLV2471IN TLV2477IN quad operational amplifier CMOS amplifier rail-to-rail input rail-to-rail output gain-bandwidth product shutdown function input bias current PDIP-16 through-hole package low-voltage analog signal conditioning battery-powered instrumentation active filter photodiode interface industrial control loop sensor signal conditioning RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें