TLV2475IN - 2.8MHz Quad R-R Op Amp | Texas Instruments
MPN: TLV2475IN ✓ 啟用中TLV2475IN 概覽
A rail-to-rail input and output operational amplifier is a voltage amplifier whose input common-mode range and output swing extend close to both supply rails. This makes it suitable for low-voltage systems in which signals may approach the positive or negative rail. Within the TLV247x family hierarchy, the TLV2475IN is a precision CMOS amplifier within the broader category of operational amplifiers and analog signal-chain ICs.
The principal specifications are a 2.8 MHz gain-bandwidth product, approximately 600 uA of quiescent current per channel, and a typical input bias current of 2.5 pA. The device operates from a nominal 2.7 V to 6 V supply range, with an extended output swing of approximately -1.35 V to +3 V. Each of the four amplifier channels also supports shutdown, allowing unused sections to be disabled when system power management is required.
The CMOS input stage supports high input impedance and low bias current, while the rail-to-rail output stage provides useful drive for sensor signals, filtering, and low-level analog processing. The 2.8 MHz gain-bandwidth product makes the amplifier appropriate for general-purpose signal conditioning, audio-frequency filtering, transducer interfaces, and feedback control loops rather than only static precision measurements.
Typical uses include battery-powered sensor conditioning, four-channel data acquisition, photodiode and phototransistor interfaces, active filters, audio preamplification, and industrial control systems operating from a single low-voltage rail. The shutdown feature can reduce consumption in portable equipment when only part of the quad amplifier is needed.
When laying out the circuit, place input-referred decoupling capacitors close to the supply pins and route sensitive input and feedback traces away from switching nodes. Confirm output settling against the selected closed-loop gain and check the shutdown logic polarity in the manufacturer datasheet before designing a power-sequencing scheme.
This page combines the manufacturer device specifications with package, application, comparison, and design guidance. It also identifies same-family drop-in candidates in the same 16-pin PDIP footprint, making it easier to plan a replacement without changing the printed circuit board.
直接替換替代品,適用於 TLV2475IN — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TLV2475IN (相同外形與佔位) — 差異在於 Amplifier Type.
TLV2475AIN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2474IN
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →TLV2472IN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2471IN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2477IN
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
TLV2475IN 最大額定值與電氣特性
| Amplifier Type | Quad operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Supply Current per Channel | 600 uA |
| Typical Input Bias Current | 2.5 pA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Nominal Supply Voltage | 2.7 V to 6 V |
| Extended Output Swing | -1.35 V to +3 V |
| Typical Output Current per Channel | 35 mA |
| Open-Loop Gain | 64 dB |
| Shutdown Control | Yes, one control for four amplifiers |
| 封裝 | 16-pin PDIP, 0.300 in (7.62 mm) row spacing |
| 安裝類型 | Through-hole |
TLV2475IN 16-pin pdip, 0.300 in (7.62 mm) row spacing 腳位配置指南
TLV2475IN(16-pin pdip, 0.300 in (7.62 mm) row spacing 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: TLV2475IN.
請參閱 資料表 以查看完整腳位配置。
典型應用
TLV2475IN 適用於 6 應用s: Battery-Powered Sensor Signal Conditioning, Four-Channel Data Acquisition, Precision Active Filtering, Audio Preamplification, Photodiode Interface, Industrial Control and Feedback Loops.
Battery-Powered Sensor Signal Conditioning
The TLV2475IN suits low-voltage sensor front ends because its 2.7 V to 6 V operating range and 600 uA-per-channel supply current support portable instrumentation. A typical 2.5 pA typical input bias current minimizes loading on high-impedance sources such as thermistors, capacitive sensors, and resistive dividers. Configure the amplifier as a non-inverting or inverting stage around the sensor, place input biasing close to the device, and use the shutdown control when a duty-cycled measurement can reduce energy use. Rail-to-rail input and output operation allows the conditioned signal to use most of the available supply range, while the 2.8 MHz gain-bandwidth product provides more headroom than required for many slow sensors.
推薦
Four-Channel Data Acquisition
The quad TLV2475IN consolidates four analog channels in one 16-pin PDIP package, reducing component count in multi-sensor acquisition systems. Each channel provides a 2.8 MHz gain-bandwidth product, rail-to-rail input and output capability, and approximately 600 uA of supply current, enabling independent signal-conditioning stages for temperature, pressure, position, or current sensing. A practical implementation assigns separate amplifier inputs to each sensor, shares a bypassed supply network, and grounds each channel reference close to its feedback divider. Verify channel-to-channel settling and crosstalk in the final layout, especially when small sensor outputs are amplified at moderate or high closed-loop gains.
推薦
Precision Active Filtering
The TLV2475IN is appropriate for second-order and higher-order active filters operating in the audio or low-frequency instrumentation range. Its 2.8 MHz gain-bandwidth product provides useful loop gain above the filter cutoff, while rail-to-rail output capability supports direct coupling to a following ADC or measurement stage. Set component values from the desired pole and quality factor, then check closed-loop stability and gain error in the manufacturer datasheet for the selected noise-gain configuration. Keep feedback resistors and capacitors physically close, maintain symmetry between differential networks, and reserve a quiet ground return for the analog section to limit filter-component noise coupling.
推薦
Audio Preamplification
The TLV2475IN can amplify low-level audio or microphone signals in a single-supply system. Rail-to-rail input handling accepts signals referenced close to ground, while the output stage provides approximately 35 mA of output current per channel for driving a following load stage. The 2.8 MHz gain-bandwidth product is suitable for audio-band amplification rather than ultrasonic applications. Choose a closed-loop gain that keeps the amplifier within its linear-output region, include an input coupling capacitor for single-supply biasing, and place the input network and feedback components away from switching regulators. The shutdown control can disable unused amplifier sections to reduce system consumption.
推薦
Photodiode Interface
The low 2.5 pA typical input bias current of the TLV2475IN makes it useful for photodiode and phototransistor interfaces where input leakage can degrade weak signals. A transimpedance configuration converts photocurrent into a measurable voltage, and the 2.8 MHz gain-bandwidth product supports faster measurement loops than the lower-speed TLV247x options. Keep the photodiode and feedback capacitor connections compact, use guarding where leakage matters, and connect the supply-return path directly to the amplifier ground. Evaluate compliance voltage, input capacitance, stability, and signal polarity using the photodiode and amplifier models for the intended light range.
推薦
Industrial Control and Feedback Loops
The TLV2475IN supports low-voltage industrial control loops that require greater bandwidth than a basic comparator-style output but less power than a high-speed amplifier. Its 2.8 MHz gain-bandwidth product provides loop gain across audio and low-frequency control ranges, while approximately 600 uA per channel keeps four-channel designs economical. Use one channel for error amplification and the others for sensor conditioning or actuator drive. Account for the amplifier's output-swing limits and phase margin, and isolate analog returns from high-current switching paths. The shutdown input is useful in staged systems that disable unused analog channels during specific operating modes.
推薦
推薦產品摘要
工程參考資料,適用於 TLV2475IN — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TLV2475AIN | TLV2474IN | TLV2472IN | TLV2471IN | TLV2477IN |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Shutdown Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Automotive-Grade Option | No | Yes | No | No | No | No |
主要差異化特點
- Higher-bandwidth member of the low-power quad amplifier family (對比TLV2474IN)
- Automotive-grade ordering path within the same amplifier family (對比TLV2475IN)
- Low-power operation combined with high input impedance (對比TLV2472IN)
設計說明
Place the supply-bypass capacitors immediately adjacent to the TLV2475IN power pins, and route each capacitor directly to a low-impedance ground plane rather than through a shared narrow trace. Keep input and feedback nets short and isolate them from switching-node copper. Because the amplifier supports rail-to-rail operation, a ground trace that carries load current can shift the effective input reference and reduce accuracy.
Use the shutdown function to disable amplifier channels that are not required, especially in battery-powered equipment. Account for both operating and shutdown current when calculating system power, and ensure the shutdown logic levels remain valid over the complete supply range. The manufacturer datasheet should be used for the shutdown-control truth table and supply-current behavior.
For photodiode, capacitive-sensor, or high-impedance source interfaces, keep the input node physically small and consider guarding to reduce surface leakage. The 2.5 pA typical input bias current is low, but PCB contamination, long traces, and temperature can still affect high-value sources. Validate leakage, settling, and achievable noise performance in the assembled board rather than relying only on ideal simulation values.
Do not assume that equal rail-to-rail input and output ratings guarantee the same usable voltage range at every load. Check output swing, input common-mode range, load current, and closed-loop gain in the Texas Instruments TLV2475 datasheet. Also verify the exact shutdown polarity and the meaning of each package pin before finalizing the schematic or PCB netlist.
合規資訊
The standard TLV2475IN is a commercial-grade device; the automotive-grade ordering option is TLV2475AIN. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.