TLV2475IN - 2.8MHz Quad R-R Op Amp | Texas Instruments
部品番号: TLV2475IN ✓ 生産中TLV2475IN 概要
A rail-to-rail input and output operational amplifier is a voltage amplifier whose input common-mode range and output swing extend close to both supply rails. This makes it suitable for low-voltage systems in which signals may approach the positive or negative rail. Within the TLV247x family hierarchy, the TLV2475IN is a precision CMOS amplifier within the broader category of operational amplifiers and analog signal-chain ICs.
The principal specifications are a 2.8 MHz gain-bandwidth product, approximately 600 uA of quiescent current per channel, and a typical input bias current of 2.5 pA. The device operates from a nominal 2.7 V to 6 V supply range, with an extended output swing of approximately -1.35 V to +3 V. Each of the four amplifier channels also supports shutdown, allowing unused sections to be disabled when system power management is required.
The CMOS input stage supports high input impedance and low bias current, while the rail-to-rail output stage provides useful drive for sensor signals, filtering, and low-level analog processing. The 2.8 MHz gain-bandwidth product makes the amplifier appropriate for general-purpose signal conditioning, audio-frequency filtering, transducer interfaces, and feedback control loops rather than only static precision measurements.
Typical uses include battery-powered sensor conditioning, four-channel data acquisition, photodiode and phototransistor interfaces, active filters, audio preamplification, and industrial control systems operating from a single low-voltage rail. The shutdown feature can reduce consumption in portable equipment when only part of the quad amplifier is needed.
When laying out the circuit, place input-referred decoupling capacitors close to the supply pins and route sensitive input and feedback traces away from switching nodes. Confirm output settling against the selected closed-loop gain and check the shutdown logic polarity in the manufacturer datasheet before designing a power-sequencing scheme.
This page combines the manufacturer device specifications with package, application, comparison, and design guidance. It also identifies same-family drop-in candidates in the same 16-pin PDIP footprint, making it easier to plan a replacement without changing the printed circuit board.
ドロップイン代替品: TLV2475IN — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TLV2475IN (同一形状・フットプリント) — 相違点: Amplifier Type.
TLV2475AIN
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
TLV2474IN
✅ ドロップイン ⚠️ 仕様未検証価格はお問い合わせください
データシートを見る →TLV2472IN
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
TLV2471IN
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
TLV2477IN
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
TLV2475IN 最大定格&電気的特性
| Amplifier Type | Quad operational amplifier |
| Number of Channels | 4 channels |
| Gain-Bandwidth Product | 2.8 MHz |
| Supply Current per Channel | 600 uA |
| Typical Input Bias Current | 2.5 pA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Nominal Supply Voltage | 2.7 V to 6 V |
| Extended Output Swing | -1.35 V to +3 V |
| Typical Output Current per Channel | 35 mA |
| Open-Loop Gain | 64 dB |
| Shutdown Control | Yes, one control for four amplifiers |
| パッケージ | 16-pin PDIP, 0.300 in (7.62 mm) row spacing |
| 実装タイプ | Through-hole |
TLV2475IN 16-pin pdip, 0.300 in (7.62 mm) row spacing ピン配置ガイド
TLV2475IN (16-pin pdip, 0.300 in (7.62 mm) row spacing パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: TLV2475IN.
詳細は データシート をご参照ください。
主な用途
TLV2475IN の用途: 6 件s: Battery-Powered Sensor Signal Conditioning, Four-Channel Data Acquisition, Precision Active Filtering, Audio Preamplification, Photodiode Interface, Industrial Control and Feedback Loops.
Battery-Powered Sensor Signal Conditioning
The TLV2475IN suits low-voltage sensor front ends because its 2.7 V to 6 V operating range and 600 uA-per-channel supply current support portable instrumentation. A typical 2.5 pA typical input bias current minimizes loading on high-impedance sources such as thermistors, capacitive sensors, and resistive dividers. Configure the amplifier as a non-inverting or inverting stage around the sensor, place input biasing close to the device, and use the shutdown control when a duty-cycled measurement can reduce energy use. Rail-to-rail input and output operation allows the conditioned signal to use most of the available supply range, while the 2.8 MHz gain-bandwidth product provides more headroom than required for many slow sensors.
おすすめ
Four-Channel Data Acquisition
The quad TLV2475IN consolidates four analog channels in one 16-pin PDIP package, reducing component count in multi-sensor acquisition systems. Each channel provides a 2.8 MHz gain-bandwidth product, rail-to-rail input and output capability, and approximately 600 uA of supply current, enabling independent signal-conditioning stages for temperature, pressure, position, or current sensing. A practical implementation assigns separate amplifier inputs to each sensor, shares a bypassed supply network, and grounds each channel reference close to its feedback divider. Verify channel-to-channel settling and crosstalk in the final layout, especially when small sensor outputs are amplified at moderate or high closed-loop gains.
おすすめ
Precision Active Filtering
The TLV2475IN is appropriate for second-order and higher-order active filters operating in the audio or low-frequency instrumentation range. Its 2.8 MHz gain-bandwidth product provides useful loop gain above the filter cutoff, while rail-to-rail output capability supports direct coupling to a following ADC or measurement stage. Set component values from the desired pole and quality factor, then check closed-loop stability and gain error in the manufacturer datasheet for the selected noise-gain configuration. Keep feedback resistors and capacitors physically close, maintain symmetry between differential networks, and reserve a quiet ground return for the analog section to limit filter-component noise coupling.
おすすめ
Audio Preamplification
The TLV2475IN can amplify low-level audio or microphone signals in a single-supply system. Rail-to-rail input handling accepts signals referenced close to ground, while the output stage provides approximately 35 mA of output current per channel for driving a following load stage. The 2.8 MHz gain-bandwidth product is suitable for audio-band amplification rather than ultrasonic applications. Choose a closed-loop gain that keeps the amplifier within its linear-output region, include an input coupling capacitor for single-supply biasing, and place the input network and feedback components away from switching regulators. The shutdown control can disable unused amplifier sections to reduce system consumption.
おすすめ
Photodiode Interface
The low 2.5 pA typical input bias current of the TLV2475IN makes it useful for photodiode and phototransistor interfaces where input leakage can degrade weak signals. A transimpedance configuration converts photocurrent into a measurable voltage, and the 2.8 MHz gain-bandwidth product supports faster measurement loops than the lower-speed TLV247x options. Keep the photodiode and feedback capacitor connections compact, use guarding where leakage matters, and connect the supply-return path directly to the amplifier ground. Evaluate compliance voltage, input capacitance, stability, and signal polarity using the photodiode and amplifier models for the intended light range.
おすすめ
Industrial Control and Feedback Loops
The TLV2475IN supports low-voltage industrial control loops that require greater bandwidth than a basic comparator-style output but less power than a high-speed amplifier. Its 2.8 MHz gain-bandwidth product provides loop gain across audio and low-frequency control ranges, while approximately 600 uA per channel keeps four-channel designs economical. Use one channel for error amplification and the others for sensor conditioning or actuator drive. Account for the amplifier's output-swing limits and phase margin, and isolate analog returns from high-current switching paths. The shutdown input is useful in staged systems that disable unused analog channels during specific operating modes.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TLV2475IN — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TLV2475AIN | TLV2474IN | TLV2472IN | TLV2471IN | TLV2477IN |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) | 16-pin PDIP (PDIP-16) |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
| Shutdown Function | Yes | Yes | Yes | Yes | Yes | Yes |
| Automotive-Grade Option | No | Yes | No | No | No | No |
主な差別化要因
- Higher-bandwidth member of the low-power quad amplifier family (vs TLV2474IN)
- Automotive-grade ordering path within the same amplifier family (vs TLV2475IN)
- Low-power operation combined with high input impedance (vs TLV2472IN)
設計ノート
Place the supply-bypass capacitors immediately adjacent to the TLV2475IN power pins, and route each capacitor directly to a low-impedance ground plane rather than through a shared narrow trace. Keep input and feedback nets short and isolate them from switching-node copper. Because the amplifier supports rail-to-rail operation, a ground trace that carries load current can shift the effective input reference and reduce accuracy.
Use the shutdown function to disable amplifier channels that are not required, especially in battery-powered equipment. Account for both operating and shutdown current when calculating system power, and ensure the shutdown logic levels remain valid over the complete supply range. The manufacturer datasheet should be used for the shutdown-control truth table and supply-current behavior.
For photodiode, capacitive-sensor, or high-impedance source interfaces, keep the input node physically small and consider guarding to reduce surface leakage. The 2.5 pA typical input bias current is low, but PCB contamination, long traces, and temperature can still affect high-value sources. Validate leakage, settling, and achievable noise performance in the assembled board rather than relying only on ideal simulation values.
Do not assume that equal rail-to-rail input and output ratings guarantee the same usable voltage range at every load. Check output swing, input common-mode range, load current, and closed-loop gain in the Texas Instruments TLV2475 datasheet. Also verify the exact shutdown polarity and the meaning of each package pin before finalizing the schematic or PCB netlist.
コンプライアンス情報
The standard TLV2475IN is a commercial-grade device; the automotive-grade ordering option is TLV2475AIN. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer product documentation.