Texas Instruments

TLV2763IN - Dual 1.8V Micropower RRIO Op Amp | TI

MPN: TLV2763IN ✓ सक्रिय
1.8 V minimum single supply Vdss 20 µA typical per channel Id 14-pin PDIP Package
न्यूनतम ऑर्डर मात्रा: 1 |

TLV2763IN अवलोकन

Texas Instruments TLV2763IN is a dual, 1.8 V micropower rail-to-rail input/output operational amplifier with shutdown, packaged in a 14-pin PDIP. The two amplifier channels operate from a single supply, provide a typical gain-bandwidth product of 500 kHz, and are suitable for low-voltage, low-power signal-conditioning systems. The TLV2763IN combines rail-to-rail inputs and outputs with a typical supply current of 20 µA per channel.

A rail-to-rail-input and rail-to-rail-output operational amplifier, commonly described as a RRIO amplifier, can accept input signals near the positive and negative supply rails while driving loads toward those limits. This makes the TLV2763IN useful when the usable input range must extend beyond conventional common-mode limits. As a dual amplifier in a 14-pin PDIP, it can implement two independent gain or buffer stages while simplifying through-hole prototype construction.

Key characteristics include 1.8 V single-supply operation, dual-channel operation, 500 kHz typical gain-bandwidth product, 20 µA typical supply current per channel, and 10.2 mA typical output current. Shutdown support is particularly useful for battery-powered instrumentation because the amplifiers can be disabled when signal-chain activity is not required, reducing system power consumption.

The TLV2763IN belongs to the operational-amplifier hierarchy, where it combines low input and output swing limits, low quiescent current, and moderate bandwidth. Its rail-to-rail behavior makes it appropriate for sensor interfaces, portable measurement systems, battery monitoring, and low-voltage analog signal chains. The shutdown function also supports duty-cycled acquisition circuits where preserving standby power is important.

Typical applications include portable sensor conditioning, low-voltage data acquisition, current-loop signal processing, audio preamplification, and general-purpose dual-stage amplification. Its 500 kHz bandwidth is appropriate for low-frequency and moderate-bandwidth instrumentation rather than high-speed video or RF signal paths. The 10.2 mA typical output-current capability is sufficient for buffer and low-load drive applications.

When designing around the TLV2763IN, account for the dropout region, output-capacitance stability requirements, input bias-current effects, and the shutdown logic level. Place input and output compensation components close to the relevant pins and avoid excessive capacitive loading at the output. Use the manufacturer datasheet pin-description table and typical application circuits to confirm external component values and logic thresholds before production release.

This page combines the manufacturer operating characteristics, package information, application guidance, and engineering-focused replacement analysis for the TLV2763IN. It also identifies the critical distinctions between genuine same-footprint alternatives and devices that are only functionally similar, helping engineers make a board-level decision without relying on incomplete catalog descriptions.

के लिए ड्रॉप-इन विकल्प TLV2763IN — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस सीरीज़ के वेरिएंट

समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं TLV2763IN (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Gain-Bandwidth Product, Package, Supply Current.

Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Gain-Bandwidth Product: 500 kHz
Package: 14-PDIP, 14 pins
इसके साथ तुलना करें TLV2763IN →

TLV2762IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
📦 14-pin PDIP
Same dual 14-pin PDIP format and low-voltage rail-to-rail architecture; shutdown capability differs, requiring a final pin-logic check

📋 संदर्भ विकल्प (कैटलॉग में नहीं)

TLV2764IN

✅ ड्रॉप-इन ⚠️ विनिर्देश असत्यापित
Texas Instruments
📦 14-pin PDIP
Quad general-purpose operational amplifier · 4 channels · Yes · Yes · 1.8 V · 3.6 V · 500 kHz · 20 µA per amplifier

कीमत के लिए संपर्क करें

डेटाशीट देखें →

TLV2763IN Maximum Ratings और Electrical Characteristics

Amplifier Type Dual operational amplifier
Number of Circuits 2 circuits
Supply Voltage Range 1.8 V minimum single supply
Supply Type Single supply
Rail-to-Rail Input Yes
Rail-to-Rail Output Yes
Gain-Bandwidth Product 500 kHz typical
सप्लाई करंट 20 µA typical per channel
Output Current 10.2 mA typical
Shutdown Function Yes
ऑपरेटिंग तापमान रेंज -40 °C to +85 °C
पैकेज 14-pin PDIP
Package Pitch 7.62 mm
माउंटिंग प्रकार Through-hole
Product Type Standard general-purpose amplifier

TLV2763IN 7.62 mm पिन कॉन्फ़िगरेशन गाइड

TLV2763IN (7.62 mm पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस एनालॉग कंपोनेंट में इनपुट, आउटपुट और पावर सप्लाई पिन हैं। ऑफ़सेट नल, कम्पनसेशन और एनेबल पिन कॉन्फ़िगरेशन के लिए निर्माता डेटाशीट देखें। सिग्नल कंडीशनिंग और एम्प्लीफ़ायर सर्किट के लिए आदर्श।

TLV2763IN के लिए 7.62 mm पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: TLV2763IN.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

TLV2763IN के लिए उपयुक्त है 6 अनुप्रयोगs: Battery-Powered Sensor Conditioning, Portable Data Acquisition, Current-Loop Signal Conditioning, Low-Voltage Audio Preamplification, Battery Monitoring, Low-Power IoT Signal Conditioning.

🧩

Battery-Powered Sensor Conditioning

The TLV2763IN fits low-power sensor interfaces because each channel typically consumes 20 µA and the family supports 1.8 V single-supply operation. Its rail-to-rail inputs preserve signal range close to the supply limits, while rail-to-rail outputs improve drive into the next low-voltage stage. Two channels can condition a sensor and its reference or provide gain and buffering without a separate dual package. The 500 kHz typical bandwidth is more than adequate for temperature, pressure, and slow chemical-sensor waveforms. Shutdown can reduce consumption during inactive measurement intervals, although the external sensor and reference loads must also be placed in a controlled off state.

🖥️

Portable Data Acquisition

The TLV2763IN is useful in portable measurement systems where two analog channels must operate from a compact 1.8 V supply. A typical arrangement uses one amplifier for gain and another for active filtering or input buffering. Its 500 kHz gain-bandwidth product supports moderate-frequency sensor acquisition while the 20 µA per-channel supply current limits power demand. Rail-to-rail input and output stages increase the usable signal span in systems whose analog front end operates near the supply rails. The shutdown function supports duty-cycled acquisition, while the through-hole 14-pin PDIP package simplifies prototype assembly and bench validation.

🏭

Current-Loop Signal Conditioning

The TLV2763IN can amplify the voltage produced by a low-side current-shunt or current-loop transmitter in a 1.8 V industrial or laboratory system. Its dual-channel arrangement permits separate gain stages for signal and reference channels, while rail-to-rail inputs accommodate sensor voltages near either supply rail. The 500 kHz typical bandwidth is suitable for many process-control signals and sensor dynamics, and the typical 10.2 mA output-current capability is appropriate for high-impedance downstream circuitry. Design the shunt, input filtering, and output loading so the amplifier remains stable with the complete sensor network and any cable capacitance.

🎧

Low-Voltage Audio Preamplification

The TLV2763IN can serve as a dual low-voltage audio preamplifier in portable equipment, microphone interface, or line-level conditioning stage. Rail-to-rail input and output operation allows the circuit to work with signals close to the 1.8 V supply, while the dual configuration can process left and right channels independently. The 500 kHz typical gain-bandwidth product covers the audio band with substantial bandwidth margin, and the typical 10.2 mA output-current capability suits normal low-impedance preamplifier loads. Shutdown is useful for battery-operated audio products, but the external microphone bias, gain-setting network, and output coupling must be designed around the amplifier's input and output behavior.

⚡

Battery Monitoring

The TLV2763IN is appropriate for monitoring a low-voltage battery or energy-storage node when the measurement circuit must operate near 1.8 V. One channel can buffer a scaled battery voltage while the other handles a current-sense signal or reference, reducing the need for separate amplifiers. Rail-to-rail inputs improve measurement utilization, and the 20 µA typical supply current per channel helps preserve standby energy. The 500 kHz bandwidth is suitable for slow voltage trends and filtered current measurements rather than high-dV/dt protection systems. Accurate results still require a suitably scaled divider or shunt, input filtering appropriate for the source impedance, and calibration across temperature.

📱

Low-Power IoT Signal Conditioning

The TLV2763IN supports IoT sensor nodes that translate low-level analog inputs into a signal suitable for sampling or comparison. Its 1.8 V operation, rail-to-rail inputs, and 20 µA per-channel supply current are useful in compact battery-powered devices, while two integrated channels can handle a sensor signal and a buffered threshold or reference. The 500 kHz typical bandwidth is suitable for many low-rate environmental sensors and avoids the power and interference burden of a much faster amplifier. Shutdown allows duty-cycled operation between measurement intervals. Layout should minimize leakage around high-impedance inputs, and the output network should avoid excessive capacitance that could compromise stability.

अनुशंसित उत्पादों का सारांश

TLV2762IN Same-family dual low-voltage amplifier option उपयोग में: Battery-Powered Sensor Conditioning, Portable Data Acquisition, Current-Loop Signal Conditioning, Low-Voltage Audio Preamplification, Battery Monitoring, Low-Power IoT Signal Conditioning TLV2764IN Texas Instruments उपयोग में: Battery-Powered Sensor Conditioning, Portable Data Acquisition, Current-Loop Signal Conditioning, Low-Voltage Audio Preamplification, Battery Monitoring, Low-Power IoT Signal Conditioning
What is the TLV2763IN?
The TLV2763IN is a dual, 1.8 V micropower operational amplifier with rail-to-rail input and output stages and shutdown support. According to the Texas Instruments TLV2763 datasheet, the device contains two amplifier circuits in a 14-pin PDIP package, operates from a single supply, and provides a typical gain-bandwidth product of 500 kHz.
What is the operating voltage of TLV2763IN?
The TLV2763IN is designed for low-voltage single-supply operation beginning at 1.8 V. The Texas Instruments TLV2763 datasheet identifies the device as part of the 1.8 V micropower family, with rail-to-rail input and output operation. Maximum supply and input limits should be confirmed against the electrical-characteristics table before applying the device to a new design.
How much current does the TLV2763IN consume?
The TLV2763IN consumes approximately 20 µA of supply current per channel under the stated typical operating conditions. Because the component contains two amplifier channels, the stated per-channel figure is the appropriate basis for power-budget calculations. The Texas Instruments TLV2763 datasheet also identifies shutdown capability for disabling the amplifiers when the application does not require continuous operation.
Where can I download the TLV2763IN datasheet PDF?
The official TLV2763 datasheet is available through the Texas Instruments product document at https://www.ti.com/lit/gpn/TLV2763. It covers the TLV2763 family, including the TLV2763IN, and contains the electrical characteristics, pin descriptions, shutdown behavior, typical performance curves, and application information needed for design review.
Where can I find the TLV2763IN pinout?
The TLV2763IN pinout is documented in the pin-configuration and pin-description sections of the Texas Instruments TLV2763 datasheet. The device is a dual amplifier in a 14-pin PDIP, so pins 1 through 14 must be assigned according to that table rather than inferred from the general amplifier category. Use the datasheet when creating the schematic symbol and PCB footprint.
Is the TLV2763IN rail-to-rail?
Yes, the TLV2763IN has rail-to-rail input and rail-to-rail output operation. According to the Texas Instruments TLV2763 datasheet, this allows the amplifier to process input signals close to the supply limits and to swing its output toward the supply rails. Actual usable swing depends on load current and output-voltage conditions.
What is the gain-bandwidth product of TLV2763IN?
The TLV2763IN has a typical gain-bandwidth product of 500 kHz. This characteristic makes it suitable for general-purpose low-voltage amplification, buffering, sensor conditioning, and moderate-bandwidth signal processing. The Texas Instruments TLV2763 datasheet should be used for gain-versus-frequency behavior and stability details at the selected closed-loop gain.
What can replace the TLV2763IN?
A valid replacement for the TLV2763IN must match its 14-pin PDIP footprint, dual-amplifier pin arrangement, 1.8 V low-voltage capability, rail-to-rail behavior, shutdown function, and approximately 500 kHz bandwidth. The TLV2762IN and TLV2764IN are same-family candidates identified for engineering review, but each must be checked for shutdown logic, supply limits, and exact pin behavior before substitution.
TLV2763IN vs TLV2762IN - which is better for a battery-powered sensor interface?
The TLV2763IN is the stronger choice when a low-power sensor interface requires the shutdown function, because the family description identifies the TLV2763 as an operational amplifier with shutdown. The TLV2762IN is a close same-family option to evaluate when shutdown is unnecessary, but the exact pin-compatible variant should be confirmed from the manufacturer documentation before changing the PCB.
When should I choose TLV2763IN instead of another dual rail-to-rail op amp?
Choose the TLV2763IN when the design combines a 14-pin PDIP footprint, 1.8 V micropower operation, dual rail-to-rail channels, approximately 500 kHz bandwidth, and shutdown control. It is especially useful for through-hole low-voltage prototypes and battery-operated instrumentation where low supply current and controlled off-state behavior matter more than high-speed performance.
Is the TLV2763IN suitable for sensor conditioning?
The TLV2763IN is suitable for low-frequency sensor-conditioning stages that operate from a 1.8 V supply and require rail-to-rail input and output behavior. Its 500 kHz typical bandwidth handles many temperature, pressure, and slow analog sensor signals, while 20 µA typical supply current per channel supports power-constrained instrumentation.
Does the TLV2763IN need an external output capacitor?
Output-capacitor requirements depend on the selected gain, load, output-voltage conditions, and stability method specified in the Texas Instruments TLV2763 datasheet. Do not add or omit compensation capacitors based only on generic rail-to-rail op-amp guidance. Follow the manufacturer typical application circuits for the intended configuration and verify stability with the final load.
What is the output-current capability of TLV2763IN?
The TLV2763IN has a typical output-current capability of 10.2 mA. This is sufficient for low-load buffering and general-purpose voltage amplification, but it should not be treated as a power-output stage. Check the datasheet output-current and output-swing curves against the intended load, including cable capacitance and transient demand.
Where can I buy TLV2763IN and what is its lead time?
The TLV2763IN can be requested through the Request a Quote form on this page, where the exact package suffix and quantity can be included with the inquiry. Current stock, manufacturing lead time, minimum order quantity, and shipment scheduling should be confirmed at the time of quotation rather than inferred from catalog listing language.
What is the price and availability of TLV2763IN?
Current TLV2763IN price and availability are not stated on this page because both can change with quantity, package suffix, and market conditions. Use the Request a Quote form on this page to request current commercial terms for the exact TLV2763IN ordering code. The manufacturer name, 14-pin PDIP package, and dual-amplifier configuration should be included in the request.
What are the key specifications of TLV2763IN that engineers should know?
The key TLV2763IN specifications are its dual configuration, 1.8 V minimum single-supply operation, rail-to-rail input and output, 500 kHz typical gain-bandwidth product, 20 µA typical supply current per channel, 10.2 mA typical output current, shutdown support, -40 °C to +85 °C operating range, and 14-pin PDIP package. These figures position it as a micropower general-purpose amplifier rather than a high-speed device.

के लिए इंजीनियरिंग संदर्भ डेटा TLV2763IN — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose the TLV2763IN for a 1.8 V, dual-channel signal chain that requires rail-to-rail input and output operation, a typical 500 kHz bandwidth, approximately 20 µA supply current per channel, and shutdown control. The 14-pin PDIP package is particularly convenient for through-hole prototypes and laboratory instrumentation. Consider the TLV2762IN when its shutdown and pin configuration satisfy the circuit and the goal is the same low-voltage dual-amplifier family. Consider the TLV2764IN when its specific channel or shutdown behavior provides a functional advantage. Neither candidate should be substituted solely from package name: verify enable polarity, compensation, input common-mode limits, output swing, and absolute maximum ratings. For designs needing more than 500 kHz bandwidth, substantially greater output current, lower noise, or a surface-mount package, move to a different amplifier family rather than assuming a drop-in replacement.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद TLV2762IN TLV2764IN
Brand Texas Instruments Texas Instruments Texas Instruments
Package 14-pin PDIP 14-pin PDIP 14-pin PDIP
Amplifier Configuration Dual Dual Dual
Minimum Supply Voltage 1.8 V 1.8 V 1.8 V
Supply Type Single supply Single supply Single supply
Rail-to-Rail Input Yes Yes Yes
Rail-to-Rail Output Yes Yes Yes

मुख्य विशेषताएँ

  • Provides a confirmed shutdown-equipped dual low-voltage configuration (बनामTLV2762IN)
  • Uses a practical 14-pin PDIP footprint for through-hole assembly (बनामTLV2764IN)
  • Balances 500 kHz bandwidth with micropower consumption (बनामTLV2764IN)

डिज़ाइन नोट्स

Budget the dual amplifier at approximately 40 µA total from the stated 20 µA typical supply current per channel. This estimate excludes external divider, sensor, and shutdown-support loads. Because the circuit operates from as little as 1.8 V, verify that every downstream signal and the shutdown-control logic remain within valid input and output ranges. Confirm the actual operating voltage against the electrical-characteristics table before using the typical current figure for a battery-life calculation.

Use the 14-pin PDIP footprint and follow the counter-clockwise numbering shown by the package drawing. Keep feedback resistors, input filtering components, and decoupling capacitors close to their associated amplifier pins. Short supply and ground paths reduce voltage drops and susceptibility from surrounding switching circuitry. If the same PCB may also carry another dual amplifier, preserve adequate clearance between packages and verify pin 1 orientation after assembly.

Do not assume that every member of the TLV2763 family has identical shutdown behavior or logic levels. Confirm the enable-pin polarity, inactive-state output condition, compensation method, and stability requirements for the exact alternative MPN in the manufacturer datasheet. Also avoid connecting high-impedance sources without accounting for input bias-current error and leakage. Validate the complete circuit at the intended supply voltage and load rather than relying on a generic rail-to-rail op-amp model.

The 500 kHz typical gain-bandwidth product makes the TLV2763IN appropriate for low-frequency and moderate-bandwidth instrumentation, but it is not intended for high-speed waveform or RF chains. Limit capacitive loading on the output and select compensation values from the manufacturer's typical application circuit. For sensor signals with wide dynamic range, use filtering and gain stages that keep the amplifier inside its linear operating region without relying on rail-to-rail output swing at heavy loads.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

The operating temperature range and general-purpose industrial-product classification are identified, but no explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 declaration appears in the listed source content.

डेटा सत्यापन तिथि: 2026-11-10 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

TLV2763IN datasheet TLV2763IN pinout TLV2763IN datasheet pdf TLV2763IN specifications TLV2763IN equivalent TLV2763IN replacement TLV2763IN vs TLV2762IN TLV2763IN price TLV2763IN stock Texas Instruments TLV2763IN TLV2763IN 1.8V micropower TLV2763IN 14-PDIP amplifier

संबंधित कंपोनेंट्स और शब्द

Texas Instruments TLV2763IN TLV2762IN TLV2764IN dual operational amplifier operational amplifier analog amplifier integrated circuit semiconductor rail-to-rail input rail-to-rail output RRIO amplifier micropower amplifier single-supply operation shutdown gain-bandwidth product supply current output current sensor conditioning portable data acquisition battery monitoring current-loop signal conditioning 14-pin PDIP through-hole package surface mount
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें