TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS9224ID ✓ सक्रियTS9224ID अवलोकन
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify small voltage differences. Its hierarchy extends from operational amplifier to analog amplifier, linear amplifier, and analog semiconductor. The TS9224 quad configuration integrates four amplifiers into one package, reducing board area while preserving independent signal paths for instrumentation, buffering, filtering, and precision control applications.
Rail-to-rail input and output behavior supports operation near the supply rails, which is useful when signal range is limited by available supply voltage. The 500 uV maximum offset-voltage rating supports precision-focused designs, while the 4 MHz gain-bandwidth product and 1.3 V/us slew rate provide useful bandwidth for general-purpose closed-loop amplifier stages. The manufacturer also identifies 500 pF capacitive-load drive and 9 nV noise as principal device characteristics.
The TS9224 family is optimized around low-noise, high-precision operation with particular emphasis on stability. This combination suits instrumentation and industrial signal paths where input offset, noise, and closed-loop behavior affect measurement quality. Four independent amplifiers in a single package can also simplify designs requiring multiple similar analog channels, although each amplifier requires correct input common-mode, output swing, and output-current conditions.
Typical uses include low-level sensor conditioning, current-sense amplifier outputs, bridge-signal interfaces, analog filtering, and precision control loops. In each case, stable closed-loop operation and rail-to-rail signal handling can reduce the need for separate input or output buffers, provided the feedback network is designed for the required gain and bandwidth.
For PCB implementation, use the manufacturer's pin configuration when assigning inputs, outputs, supply rails, and feedback components. Place input, output, feedback, and decoupling connections to minimize loop area and susceptibility to noise. Because the device can drive capacitive loads up to 500 pF, isolate difficult loads with series resistance when necessary to preserve stability.
This product page combines the TS9224ID electrical characteristics, package details, drop-in alternatives, comparison parameters, and application-focused design guidance to support component selection, PCB planning, and precision analog circuit design.
के लिए ड्रॉप-इन विकल्प TS9224ID — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।
इस सीरीज़ के वेरिएंट
समान श्रृंखला के मॉडल जो ड्रॉप-इन संगत हैं TS9224ID (समान फॉर्म फैक्टर और फुटप्रिंट) — इसमें भिन्न Amplifier Type, Package.
TS9224IYPT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TS9224IPT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TS9224IYDT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TS9224IDT
✅ ड्रॉप-इन📋 संदर्भ विकल्प (कैटलॉग में नहीं)
TS924ID
✅ ड्रॉप-इनकीमत के लिए संपर्क करें
डेटाशीट देखें →TS9224ID Maximum Ratings और Electrical Characteristics
| Amplifier Type | General Purpose |
| Number of Circuits | 4 circuits |
| Input Offset Voltage | 500 uV maximum |
| Gain-Bandwidth Product | 4 MHz |
| Slew Rate | 1.3 V/us |
| Noise Voltage | 9 nV |
| Capacitive Load Drive | 500 pF |
| Output Current | 80 mA |
| Differential Input Voltage | 2 kV |
| Input Characteristics | Rail-to-rail |
| Output Characteristics | Rail-to-rail |
| पैकेज | 14-SO, 3.90 mm width |
| माउंटिंग प्रकार | Surface Mount |
| Shipping Packaging | Tube |
TS9224ID पिन कॉन्फ़िगरेशन
| पिन 1 | OUT1 — Amplifier 1 output |
| पिन 2 | IN1- — Amplifier 1 inverting input |
| पिन 3 | IN1+ — Amplifier 1 non-inverting input |
| पिन 4 | V+ — Positive supply voltage |
| पिन 5 | IN2+ — Amplifier 2 non-inverting input |
| पिन 6 | IN2- — Amplifier 2 inverting input |
| पिन 7 | OUT2 — Amplifier 2 output |
| पिन 8 | OUT3 — Amplifier 3 output |
| पिन 9 | IN3- — Amplifier 3 inverting input |
| पिन 10 | IN3+ — Amplifier 3 non-inverting input |
| पिन 11 | V- — Negative supply voltage |
| पिन 12 | IN4+ — Amplifier 4 non-inverting input |
| पिन 13 | IN4- — Amplifier 4 inverting input |
| पिन 14 | OUT4 — Amplifier 4 output |
सामान्य अनुप्रयोग
TS9224ID के लिए उपयुक्त है 6 अनुप्रयोगs: Precision Sensor Signal Conditioning, Current-Sense Amplifier Interface, Industrial Bridge and Sensor Front End, Precision Analog Filtering, Audio and Communication Buffering, Automotive and Industrial Control Loops.
Precision Sensor Signal Conditioning
The TS9224ID fits low-level sensor conditioning because its 500 uV maximum input offset voltage and 9 nV noise rating help preserve small differential signals, while its 4 MHz gain-bandwidth product supports practical closed-loop bandwidth. Four amplifiers in one 14-SOIC package allow related sensing channels to share a compact implementation. The rail-to-rail input characteristic is useful when the sensor output approaches a supply rail. The designer must still verify the common-mode range, input bias current, sensor impedance, and required noise gain against the manufacturer datasheet.
अनुशंसित
Current-Sense Amplifier Interface
The TS9224ID can buffer the output of a current-sense amplifier and provide additional gain before an ADC or control system. Its 9 nV noise specification is favorable for low-level current measurements, and the 1.3 V/us slew rate supports dynamic waveforms produced by motor or power-system monitoring circuits. With four independent amplifiers, two channels might amplify positive and negative shunt signals while the other channels perform filtering or level conditioning. Input-offset error and common-mode limits must remain compatible with the shunt amplifier's output range.
अनुशंसित
Industrial Bridge and Sensor Front End
A strain-gauge or resistive-bridge front end benefits from the TS9224ID's 500 uV maximum offset-voltage rating and low-noise architecture. The quad package provides separate amplifier stages for excitation buffering, differential sensing, scaling, and active filtering while reducing board area. Rail-to-rail input and output operation can improve usable dynamic range in low-voltage industrial systems. Because bridge signals are small and sensitive to thermal effects, the circuit should include suitable input filtering, stable reference excitation, and layout symmetry while staying within the device's supply and common-mode limits.
अनुशंसित
Precision Analog Filtering
The TS9224ID is suitable for active filter stages where low input offset and 9 nV noise contribute to signal integrity. Its 4 MHz gain-bandwidth product can implement moderate-bandwidth low-pass, high-pass, or band-pass sections using conventional RC networks, while the 1.3 V/us slew rate helps preserve large-signal behavior at lower frequencies. The quad arrangement allows a multi-stage filter or several independent channels in one package. Component tolerances, op-amp noise gain, capacitive loading, and the manufacturer's recommended stability network should be evaluated for the selected topology.
अनुशंसित
Audio and Communication Buffering
The TS9224ID can provide impedance buffering, gain, or level conditioning for low-level audio and communication signals. Its 9 nV noise rating and 500 uV maximum offset voltage support low-distortion signal handling, while rail-to-rail input and output operation helps preserve signal swing near the available supply limits. The 4 MHz gain-bandwidth product is suitable for many audio-band and low-frequency communication channels. Actual distortion and bandwidth depend on the selected gain, load, output swing, and feedback network, so the output should remain within the manufacturer load-current and stability limits.
अनुशंसित
Automotive and Industrial Control Loops
The TS9224ID is appropriate for precision control-loop inputs where offset and noise can influence actuator commands or feedback accuracy. Its 500 uV maximum input offset voltage and 4 MHz gain-bandwidth product support low-frequency error-amplifier roles, while four circuits can combine sensing, filtering, error amplification, and output drive in one package. Automotive designs must select the correct qualified order variant and confirm temperature and qualification requirements. Grounding, decoupling, and output isolation are critical when the control system includes relays, motor stages, or long analog wiring.
अनुशंसित
अनुशंसित उत्पादों का सारांश
के लिए इंजीनियरिंग संदर्भ डेटा TS9224ID — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।
चयन गाइड
विकल्पों के साथ तुलना
| पैरामीटर | यह उत्पाद | TS9224IYPT | TS9224IPT | TS9224IYDT | TS9224IDT | TS924ID |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Type | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose |
| Input and Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
मुख्य विशेषताएँ
- Four precision amplifier channels in one package (बनामTS924ID)
- Higher specified gain-bandwidth product within the TS9224 family (बनामTS9224IYPT)
- Rail-to-rail precision operation (बनामTS924ID)
डिज़ाइन नोट्स
Use the manufacturer's 14-SO land pattern and confirm pin-1 orientation before routing. Place supply-decoupling capacitance at the positive supply and ground pins, keep feedback components close to their amplifier pins, and minimize the area of the non-inverting input node. Sensitive amplifier channels should be physically separated from switching nodes, relay drivers, and high-current output paths to reduce differential coupling.
Rail-to-rail input does not remove every common-mode or output-swing restriction; use the exact electrical limits in the manufacturer datasheet for the selected grade. In particular, check input range near the negative rail, output swing under load, output-current direction, and maximum differential input voltage of 2 kV. A common design error is assuming the 500 uV offset rating applies across all temperature and common-mode conditions.
Although the device can drive 500 pF, long PCB traces, cables, and ADC sampling nodes can create additional capacitance that reduces stability margin. Place a small series resistor between the amplifier output and a difficult load, and validate the complete closed-loop response with an oscilloscope. Keep the resistor close to the output pin and account for its interaction with the feedback network and intended load.
अनुपालन जानकारी
The manufacturer describes the TS9224 family for automotive and industrial applications. Exact environmental compliance and qualification status for the TS9224ID order code must be confirmed through current product documentation; automotive-qualified TS9224 order variants are listed separately.