TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS9224ID ✓ 啟用中TS9224ID 概覽
An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify small voltage differences. Its hierarchy extends from operational amplifier to analog amplifier, linear amplifier, and analog semiconductor. The TS9224 quad configuration integrates four amplifiers into one package, reducing board area while preserving independent signal paths for instrumentation, buffering, filtering, and precision control applications.
Rail-to-rail input and output behavior supports operation near the supply rails, which is useful when signal range is limited by available supply voltage. The 500 uV maximum offset-voltage rating supports precision-focused designs, while the 4 MHz gain-bandwidth product and 1.3 V/us slew rate provide useful bandwidth for general-purpose closed-loop amplifier stages. The manufacturer also identifies 500 pF capacitive-load drive and 9 nV noise as principal device characteristics.
The TS9224 family is optimized around low-noise, high-precision operation with particular emphasis on stability. This combination suits instrumentation and industrial signal paths where input offset, noise, and closed-loop behavior affect measurement quality. Four independent amplifiers in a single package can also simplify designs requiring multiple similar analog channels, although each amplifier requires correct input common-mode, output swing, and output-current conditions.
Typical uses include low-level sensor conditioning, current-sense amplifier outputs, bridge-signal interfaces, analog filtering, and precision control loops. In each case, stable closed-loop operation and rail-to-rail signal handling can reduce the need for separate input or output buffers, provided the feedback network is designed for the required gain and bandwidth.
For PCB implementation, use the manufacturer's pin configuration when assigning inputs, outputs, supply rails, and feedback components. Place input, output, feedback, and decoupling connections to minimize loop area and susceptibility to noise. Because the device can drive capacitive loads up to 500 pF, isolate difficult loads with series resistance when necessary to preserve stability.
This product page combines the TS9224ID electrical characteristics, package details, drop-in alternatives, comparison parameters, and application-focused design guidance to support component selection, PCB planning, and precision analog circuit design.
直接替換替代品,適用於 TS9224ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TS9224ID (相同外形與佔位) — 差異在於 Amplifier Type, Package.
TS9224IYPT
✅ 直接替換📋 參考替代品(不在目錄中)
TS9224IPT
✅ 直接替換📋 參考替代品(不在目錄中)
TS9224IYDT
✅ 直接替換📋 參考替代品(不在目錄中)
TS9224IDT
✅ 直接替換📋 參考替代品(不在目錄中)
TS9224ID 最大額定值與電氣特性
| Amplifier Type | General Purpose |
| Number of Circuits | 4 circuits |
| Input Offset Voltage | 500 uV maximum |
| Gain-Bandwidth Product | 4 MHz |
| Slew Rate | 1.3 V/us |
| Noise Voltage | 9 nV |
| Capacitive Load Drive | 500 pF |
| Output Current | 80 mA |
| Differential Input Voltage | 2 kV |
| Input Characteristics | Rail-to-rail |
| Output Characteristics | Rail-to-rail |
| 封裝 | 14-SO, 3.90 mm width |
| 安裝類型 | Surface Mount |
| Shipping Packaging | Tube |
TS9224ID 腳位配置
| 腳位 1 | OUT1 — Amplifier 1 output |
| 腳位 2 | IN1- — Amplifier 1 inverting input |
| 腳位 3 | IN1+ — Amplifier 1 non-inverting input |
| 腳位 4 | V+ — Positive supply voltage |
| 腳位 5 | IN2+ — Amplifier 2 non-inverting input |
| 腳位 6 | IN2- — Amplifier 2 inverting input |
| 腳位 7 | OUT2 — Amplifier 2 output |
| 腳位 8 | OUT3 — Amplifier 3 output |
| 腳位 9 | IN3- — Amplifier 3 inverting input |
| 腳位 10 | IN3+ — Amplifier 3 non-inverting input |
| 腳位 11 | V- — Negative supply voltage |
| 腳位 12 | IN4+ — Amplifier 4 non-inverting input |
| 腳位 13 | IN4- — Amplifier 4 inverting input |
| 腳位 14 | OUT4 — Amplifier 4 output |
典型應用
TS9224ID 適用於 6 應用s: Precision Sensor Signal Conditioning, Current-Sense Amplifier Interface, Industrial Bridge and Sensor Front End, Precision Analog Filtering, Audio and Communication Buffering, Automotive and Industrial Control Loops.
Precision Sensor Signal Conditioning
The TS9224ID fits low-level sensor conditioning because its 500 uV maximum input offset voltage and 9 nV noise rating help preserve small differential signals, while its 4 MHz gain-bandwidth product supports practical closed-loop bandwidth. Four amplifiers in one 14-SOIC package allow related sensing channels to share a compact implementation. The rail-to-rail input characteristic is useful when the sensor output approaches a supply rail. The designer must still verify the common-mode range, input bias current, sensor impedance, and required noise gain against the manufacturer datasheet.
推薦
Current-Sense Amplifier Interface
The TS9224ID can buffer the output of a current-sense amplifier and provide additional gain before an ADC or control system. Its 9 nV noise specification is favorable for low-level current measurements, and the 1.3 V/us slew rate supports dynamic waveforms produced by motor or power-system monitoring circuits. With four independent amplifiers, two channels might amplify positive and negative shunt signals while the other channels perform filtering or level conditioning. Input-offset error and common-mode limits must remain compatible with the shunt amplifier's output range.
推薦
Industrial Bridge and Sensor Front End
A strain-gauge or resistive-bridge front end benefits from the TS9224ID's 500 uV maximum offset-voltage rating and low-noise architecture. The quad package provides separate amplifier stages for excitation buffering, differential sensing, scaling, and active filtering while reducing board area. Rail-to-rail input and output operation can improve usable dynamic range in low-voltage industrial systems. Because bridge signals are small and sensitive to thermal effects, the circuit should include suitable input filtering, stable reference excitation, and layout symmetry while staying within the device's supply and common-mode limits.
推薦
Precision Analog Filtering
The TS9224ID is suitable for active filter stages where low input offset and 9 nV noise contribute to signal integrity. Its 4 MHz gain-bandwidth product can implement moderate-bandwidth low-pass, high-pass, or band-pass sections using conventional RC networks, while the 1.3 V/us slew rate helps preserve large-signal behavior at lower frequencies. The quad arrangement allows a multi-stage filter or several independent channels in one package. Component tolerances, op-amp noise gain, capacitive loading, and the manufacturer's recommended stability network should be evaluated for the selected topology.
推薦
Audio and Communication Buffering
The TS9224ID can provide impedance buffering, gain, or level conditioning for low-level audio and communication signals. Its 9 nV noise rating and 500 uV maximum offset voltage support low-distortion signal handling, while rail-to-rail input and output operation helps preserve signal swing near the available supply limits. The 4 MHz gain-bandwidth product is suitable for many audio-band and low-frequency communication channels. Actual distortion and bandwidth depend on the selected gain, load, output swing, and feedback network, so the output should remain within the manufacturer load-current and stability limits.
推薦
Automotive and Industrial Control Loops
The TS9224ID is appropriate for precision control-loop inputs where offset and noise can influence actuator commands or feedback accuracy. Its 500 uV maximum input offset voltage and 4 MHz gain-bandwidth product support low-frequency error-amplifier roles, while four circuits can combine sensing, filtering, error amplification, and output drive in one package. Automotive designs must select the correct qualified order variant and confirm temperature and qualification requirements. Grounding, decoupling, and output isolation are critical when the control system includes relays, motor stages, or long analog wiring.
推薦
推薦產品摘要
工程參考資料,適用於 TS9224ID — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TS9224IYPT | TS9224IPT | TS9224IYDT | TS9224IDT | TS924ID |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Amplifier Type | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose | General Purpose |
| Input and Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
主要差異化特點
- Four precision amplifier channels in one package (對比TS924ID)
- Higher specified gain-bandwidth product within the TS9224 family (對比TS9224IYPT)
- Rail-to-rail precision operation (對比TS924ID)
設計說明
Use the manufacturer's 14-SO land pattern and confirm pin-1 orientation before routing. Place supply-decoupling capacitance at the positive supply and ground pins, keep feedback components close to their amplifier pins, and minimize the area of the non-inverting input node. Sensitive amplifier channels should be physically separated from switching nodes, relay drivers, and high-current output paths to reduce differential coupling.
Rail-to-rail input does not remove every common-mode or output-swing restriction; use the exact electrical limits in the manufacturer datasheet for the selected grade. In particular, check input range near the negative rail, output swing under load, output-current direction, and maximum differential input voltage of 2 kV. A common design error is assuming the 500 uV offset rating applies across all temperature and common-mode conditions.
Although the device can drive 500 pF, long PCB traces, cables, and ADC sampling nodes can create additional capacitance that reduces stability margin. Place a small series resistor between the amplifier output and a difficult load, and validate the complete closed-loop response with an oscilloscope. Keep the resistor close to the output pin and account for its interaction with the feedback network and intended load.
合規資訊
The manufacturer describes the TS9224 family for automotive and industrial applications. Exact environmental compliance and qualification status for the TS9224ID order code must be confirmed through current product documentation; automotive-qualified TS9224 order variants are listed separately.