STMicroelectronics

TS9224ID - 4-Channel Precision Rail-to-Rail Op Amp | STMicroelectronics

MPN: TS9224ID ✓ فعال
500 uV maximum Vdss 80 mA Id 14-SO, 3.90 mm width Package
حداقل سفارش: 1 |

TS9224ID نمای کلی

The STMicroelectronics TS9224ID is a four-circuit, general-purpose operational amplifier optimized for precision, low noise, and stability, with rail-to-rail input and output operation in a 14-pin SOIC package. Key ratings include 500 uV maximum input offset voltage, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 9 nV noise, and 500 pF capacitive-load drive capability.

An operational amplifier is an analog signal-conditioning IC that uses high open-loop gain to amplify small voltage differences. Its hierarchy extends from operational amplifier to analog amplifier, linear amplifier, and analog semiconductor. The TS9224 quad configuration integrates four amplifiers into one package, reducing board area while preserving independent signal paths for instrumentation, buffering, filtering, and precision control applications.

Rail-to-rail input and output behavior supports operation near the supply rails, which is useful when signal range is limited by available supply voltage. The 500 uV maximum offset-voltage rating supports precision-focused designs, while the 4 MHz gain-bandwidth product and 1.3 V/us slew rate provide useful bandwidth for general-purpose closed-loop amplifier stages. The manufacturer also identifies 500 pF capacitive-load drive and 9 nV noise as principal device characteristics.

The TS9224 family is optimized around low-noise, high-precision operation with particular emphasis on stability. This combination suits instrumentation and industrial signal paths where input offset, noise, and closed-loop behavior affect measurement quality. Four independent amplifiers in a single package can also simplify designs requiring multiple similar analog channels, although each amplifier requires correct input common-mode, output swing, and output-current conditions.

Typical uses include low-level sensor conditioning, current-sense amplifier outputs, bridge-signal interfaces, analog filtering, and precision control loops. In each case, stable closed-loop operation and rail-to-rail signal handling can reduce the need for separate input or output buffers, provided the feedback network is designed for the required gain and bandwidth.

For PCB implementation, use the manufacturer's pin configuration when assigning inputs, outputs, supply rails, and feedback components. Place input, output, feedback, and decoupling connections to minimize loop area and susceptibility to noise. Because the device can drive capacitive loads up to 500 pF, isolate difficult loads with series resistance when necessary to preserve stability.

This product page combines the TS9224ID electrical characteristics, package details, drop-in alternatives, comparison parameters, and application-focused design guidance to support component selection, PCB planning, and precision analog circuit design.

جایگزین‌های drop-in برای TS9224ID — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای TS9224ID (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Amplifier Type, Package.

STMicroelectronics
Amplifier Type: Rail-to-Rail operational amplifier
Package: 14-pin small-outline package (14-SO)
مقایسه با TS9224ID →

TS9224IYPT

✅ جایگزین مستقیم
📦 14-SOIC
Industrial temperature suffix differs from TS9224ID; principal performance parameters are reported as identical with 0 uV measured difference.

📋 جایگزین مرجع (خارج از کاتالوگ)

TS9224IPT

✅ جایگزین مستقیم
📦 14-SOIC
Automotive-qualified order variant with the same TS9224 electrical family and 14-SO pin arrangement.

📋 جایگزین مرجع (خارج از کاتالوگ)

TS9224IYDT

✅ جایگزین مستقیم
📦 14-SOIC
Industrial temperature and reel-shipping suffix differs from TS9224ID; core amplifier ratings remain within the same family.

📋 جایگزین مرجع (خارج از کاتالوگ)

TS9224IDT

✅ جایگزین مستقیم
📦 14-SOIC
Reel-shipping suffix differs from TS9224ID; electrical ratings and 14-SO footprint are unchanged, giving 0% functional difference.

📋 جایگزین مرجع (خارج از کاتالوگ)

TS924ID

✅ جایگزین مستقیم
STMicroelectronics
📦 14-SOIC
4 circuits · Rail-to-Rail operational amplifier · BiCMOS · 3 V to 5 V operation · 80 mA · 80 dB · 0.1 µA · 5000 µV

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

TS9224ID حداکثر مقادیر مجاز و مشخصات الکتریکی

Amplifier Type General Purpose
Number of Circuits 4 circuits
Input Offset Voltage 500 uV maximum
Gain-Bandwidth Product 4 MHz
Slew Rate 1.3 V/us
Noise Voltage 9 nV
Capacitive Load Drive 500 pF
Output Current 80 mA
Differential Input Voltage 2 kV
Input Characteristics Rail-to-rail
Output Characteristics Rail-to-rail
بسته‌بندی 14-SO, 3.90 mm width
نوع نصب Surface Mount
Shipping Packaging Tube

پیکربندی پین TS9224ID

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
پین 1 OUT1 — Amplifier 1 output
پین 2 IN1- — Amplifier 1 inverting input
پین 3 IN1+ — Amplifier 1 non-inverting input
پین 4 V+ — Positive supply voltage
پین 5 IN2+ — Amplifier 2 non-inverting input
پین 6 IN2- — Amplifier 2 inverting input
پین 7 OUT2 — Amplifier 2 output
پین 8 OUT3 — Amplifier 3 output
پین 9 IN3- — Amplifier 3 inverting input
پین 10 IN3+ — Amplifier 3 non-inverting input
پین 11 V- — Negative supply voltage
پین 12 IN4+ — Amplifier 4 non-inverting input
پین 13 IN4- — Amplifier 4 inverting input
پین 14 OUT4 — Amplifier 4 output

کاربردهای معمول

TS9224ID مناسب است برای 6 کاربردs: Precision Sensor Signal Conditioning, Current-Sense Amplifier Interface, Industrial Bridge and Sensor Front End, Precision Analog Filtering, Audio and Communication Buffering, Automotive and Industrial Control Loops.

🏭

Precision Sensor Signal Conditioning

The TS9224ID fits low-level sensor conditioning because its 500 uV maximum input offset voltage and 9 nV noise rating help preserve small differential signals, while its 4 MHz gain-bandwidth product supports practical closed-loop bandwidth. Four amplifiers in one 14-SOIC package allow related sensing channels to share a compact implementation. The rail-to-rail input characteristic is useful when the sensor output approaches a supply rail. The designer must still verify the common-mode range, input bias current, sensor impedance, and required noise gain against the manufacturer datasheet.

⚡

Current-Sense Amplifier Interface

The TS9224ID can buffer the output of a current-sense amplifier and provide additional gain before an ADC or control system. Its 9 nV noise specification is favorable for low-level current measurements, and the 1.3 V/us slew rate supports dynamic waveforms produced by motor or power-system monitoring circuits. With four independent amplifiers, two channels might amplify positive and negative shunt signals while the other channels perform filtering or level conditioning. Input-offset error and common-mode limits must remain compatible with the shunt amplifier's output range.

🏭

Industrial Bridge and Sensor Front End

A strain-gauge or resistive-bridge front end benefits from the TS9224ID's 500 uV maximum offset-voltage rating and low-noise architecture. The quad package provides separate amplifier stages for excitation buffering, differential sensing, scaling, and active filtering while reducing board area. Rail-to-rail input and output operation can improve usable dynamic range in low-voltage industrial systems. Because bridge signals are small and sensitive to thermal effects, the circuit should include suitable input filtering, stable reference excitation, and layout symmetry while staying within the device's supply and common-mode limits.

📡

Precision Analog Filtering

The TS9224ID is suitable for active filter stages where low input offset and 9 nV noise contribute to signal integrity. Its 4 MHz gain-bandwidth product can implement moderate-bandwidth low-pass, high-pass, or band-pass sections using conventional RC networks, while the 1.3 V/us slew rate helps preserve large-signal behavior at lower frequencies. The quad arrangement allows a multi-stage filter or several independent channels in one package. Component tolerances, op-amp noise gain, capacitive loading, and the manufacturer's recommended stability network should be evaluated for the selected topology.

🎧

Audio and Communication Buffering

The TS9224ID can provide impedance buffering, gain, or level conditioning for low-level audio and communication signals. Its 9 nV noise rating and 500 uV maximum offset voltage support low-distortion signal handling, while rail-to-rail input and output operation helps preserve signal swing near the available supply limits. The 4 MHz gain-bandwidth product is suitable for many audio-band and low-frequency communication channels. Actual distortion and bandwidth depend on the selected gain, load, output swing, and feedback network, so the output should remain within the manufacturer load-current and stability limits.

🚗

Automotive and Industrial Control Loops

The TS9224ID is appropriate for precision control-loop inputs where offset and noise can influence actuator commands or feedback accuracy. Its 500 uV maximum input offset voltage and 4 MHz gain-bandwidth product support low-frequency error-amplifier roles, while four circuits can combine sensing, filtering, error amplification, and output drive in one package. Automotive designs must select the correct qualified order variant and confirm temperature and qualification requirements. Grounding, decoupling, and output isolation are critical when the control system includes relays, motor stages, or long analog wiring.

What are the key specifications of TS9224ID that engineers should know?
The TS9224ID is a four-circuit, general-purpose operational amplifier with 500 uV maximum input offset voltage, a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 9 nV noise, and 500 pF capacitive-load drive capability. According to the STMicroelectronics manufacturer datasheet, its rail-to-rail input and output characteristics support signal operation close to the supply rails. The device is packaged in a 14-pin SOIC and is intended for precision, noise-sensitive, automotive, and industrial signal-conditioning applications.
What is the operating voltage range of TS9224ID?
The operating supply-voltage range should be taken from the electrical-characteristics table in the STMicroelectronics manufacturer datasheet for the exact TS9224ID order code. The available product information confirms a 14-SO package, four amplifiers, and rail-to-rail input and output operation but does not state a numerical supply range. Use the manufacturer limits when checking rail-to-rail range, common-mode input limits, and output-swing calculations, particularly for low-voltage or battery-powered systems.
Where can I download the TS9224ID datasheet PDF?
The official TS9224 product page provides the manufacturer documentation for the TS9222 and TS9224 amplifier family, while the family PDF covers TS9222, TS9224, TS9224ID, TS9224IDT, TS9224IPT, and TS9224IYDT order variants. The STMicroelectronics manufacturer datasheet is the preferred document for the pin configuration, electrical characteristics, package dimensions, and application guidance. Confirm all ratings against the ordering-information table when using an automotive-grade suffix.
Where can I find the TS9224ID pinout?
The TS9224ID pinout is shown in the STMicroelectronics manufacturer datasheet and uses a 14-pin SOIC arrangement for four amplifiers. Pins 1 through 7 carry amplifier 1 and amplifier 2 signals and the positive supply, while pins 8 through 14 carry amplifier 3, amplifier 4, and the negative supply. Verify the printed pin numbers against the selected package orientation before assigning PCB nets, especially the two supply pins and all eight amplifier input and output pins.
Can TS9224ID be used for low-level sensor signal conditioning?
Yes, the TS9224ID is suitable for low-level sensor conditioning when the circuit requires modest bandwidth and the input offset and noise are acceptable for the measurement accuracy. Its 500 uV maximum input offset voltage, 9 nV noise rating, and 4 MHz gain-bandwidth product support precision-focused instrumentation stages. The rail-to-rail input and output characteristics can also improve signal utilization when the measured range lies close to a supply rail. Final suitability depends on sensor source impedance, common-mode range, and required closed-loop gain.
What is the difference between TS9224ID and TS924ID?
Both are STMicroelectronics four-circuit, general-purpose, rail-to-rail amplifiers offered in the 14-SO package, but they belong to different amplifier families and should not be treated as identical without checking the manufacturer data. The TS9224ID is specified at 500 uV maximum offset voltage, 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 9 nV noise. The TS924 family is described as a quad BiCMOS amplifier optimized and fully specified for 3 V and 5 V operation, so the preferred replacement depends on the individual electrical limits of each device.
When should I choose TS9224ID over TS924ID?
Choose the TS9224ID when the design values the family characterized for high precision, low noise, and stability and is matched to its 500 uV maximum offset voltage, 4 MHz bandwidth, 1.3 V/us slew rate, and 9 nV noise ratings. Choose the TS924ID when its specific 3 V and 5 V optimization matches the supply plan more closely and its complete electrical table satisfies the application. Because both use a 14-SO outline, package compatibility does not by itself establish functional or parametric equivalence.
What is the best drop-in replacement for TS9224ID?
The closest documented same-family choice is TS9224IYPT, whose comparison listing reports identical primary performance parameters and functionally equivalent operation for most designs. The TS9224IPT and TS9224IYDT automotive-qualified order variants are also family alternatives, while TS9224IDT changes the shipping format rather than the electrical device. For each candidate, verify the exact temperature grade, qualification status, supply-voltage limits, pin mapping, and footprint on the STMicroelectronics manufacturer datasheet before treating it as a drop-in replacement.
Is TS9224ID the same as TS9224IYPT?
The TS9224ID and TS9224IYPT are closely related STMicroelectronics quad operational amplifiers with identical reported primary performance profiles, but their order suffixes can denote different qualification, temperature, or shipment categories. The direct comparison identifies no measurable difference in the principal technical parameters. The TS9224IYPT normally denotes an industrial temperature option, while the exact suffix definitions must be confirmed in the ordering table. Check the required grade and package form before substitution.
What can replace TS9224ID?
TS9224IYPT is the closest listed replacement because its primary technical parameters are reported as identical and it remains within the TS9224 four-amplifier family. TS9224IPT and TS9224IYDT provide automotive-qualified order variants for designs requiring that qualification, while TS9224IDT is an electrically equivalent shipping-format option. Before replacing TS9224ID, confirm that the alternative retains a 14-SO footprint, matching pin functions, the required temperature range, and acceptable offset, noise, bandwidth, and supply-voltage behavior.
Is TS9224ID suitable for driving a 500 pF capacitive load?
Yes, the TS9224ID is characterized for driving capacitive loads up to 500 pF. However, the STMicroelectronics manufacturer datasheet identifies capacitive-load drive as a key feature rather than a guarantee for every feedback topology and frequency. Use the closed-loop configuration, gain, output voltage, and load conditions specified by the manufacturer. When driving longer cables, ADC sampling inputs, or other highly capacitive loads, add an isolation resistor and verify stability with oscilloscope measurements.
How should I design the PCB layout for TS9224ID?
Place the decoupling capacitor close to the positive supply pin and connect the negative supply pin to a low-impedance ground plane. Keep each amplifier's feedback components adjacent to their associated pins, minimize non-inverting input traces, and route sensitive inputs away from switching nodes and high-current outputs. The 14-SO footprint must match the manufacturer's land pattern, including pin-1 orientation. Because the amplifier can drive 500 pF, use a small series output resistor when a long trace or capacitive load could degrade closed-loop stability.
What thermal and power considerations apply to TS9224ID?
TS9224ID is a low-voltage analog IC rather than a power semiconductor, so safe-operating-area data do not apply. Thermal design begins with the device's maximum supply voltage, total supply current, ambient temperature, and package dissipation limit in the STMicroelectronics manufacturer datasheet. Estimated: with a 5 V supply and 4 mA total supply current, the maximum input-to-output power attributable to the amplifier is approximately 20 mW, excluding output-stage dissipation. Confirm actual dissipation with operating-current and output-voltage measurements.
Where to buy TS9224ID online?
Use the Request a Quote form on this page to request TS9224ID availability, current lead time, and order quantities. The request identifies the exact STMicroelectronics TS9224ID four-circuit operational amplifier in the 14-SO package, allowing procurement to confirm lot availability and shipping form. The device is also cataloged as standard general-purpose product with a tube shipping option, but current inventory should be confirmed through this page's quote process rather than assumed from a catalog record.
What is the price and lead time for TS9224ID?
Current price and lead time for TS9224ID should be obtained through the Request a Quote form on this page. The quote team can confirm the exact MPN, tube packaging, minimum order quantity, production status, and current allocation for the four-circuit 14-SO operational amplifier. The 500 uV maximum offset voltage, 4 MHz gain-bandwidth product, and rail-to-rail architecture define the device technically; they do not establish current commercial terms. Submit one request for pricing and lead-time confirmation.
Is TS9224ID in stock and what is its compliance status?
Current TS9224ID stock should be confirmed through the Request a Quote form on this page, including the desired tube quantity and manufacturing schedule. The manufacturer describes the TS9224 family for automotive and industrial applications, but the exact RoHS, REACH, lead-free, halogen-free, and AEC-Q100 status for the TS9224ID order code must be taken from its current product documentation. Use the Request a Quote form for availability and request the applicable environmental and qualification documents for the selected lot.

داده‌های مرجع مهندسی برای TS9224ID — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the TS9224ID when a design needs four general-purpose precision amplifier channels with 500 uV maximum offset voltage, 9 nV noise, 4 MHz gain-bandwidth product, and rail-to-rail input and output behavior. It is especially appropriate for low-level instrumentation, current-sense interfaces, active filtering, and compact industrial control circuits. Select TS9224IYPT when its industrial temperature ordering category matches the required grade and its principal parameters match the target. Select TS9224IPT or TS9224IYDT when automotive qualification is required and the corresponding ordering information confirms suitability. TS9224IDT is appropriate when reel shipping is preferred with the same electrical configuration. Consider TS924ID only when its separate 3 V and 5 V optimization better matches the supply design and its complete electrical limits satisfy the circuit. In every substitution, verify the 14-SO footprint, pin functions, common-mode range, output swing, temperature grade, and qualification documentation.

مقایسه با جایگزین‌ها

پارامتر این محصول TS9224IYPT TS9224IPT TS9224IYDT TS9224IDT TS924ID
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Number of Circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits 4 circuits
Amplifier Type General Purpose General Purpose General Purpose General Purpose General Purpose General Purpose
Input and Output Swing Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail

تفاوت‌های کلیدی

  • Four precision amplifier channels in one package (در مقابلTS924ID)
  • Higher specified gain-bandwidth product within the TS9224 family (در مقابلTS9224IYPT)
  • Rail-to-rail precision operation (در مقابلTS924ID)

یادداشت‌های طراحی

Use the manufacturer's 14-SO land pattern and confirm pin-1 orientation before routing. Place supply-decoupling capacitance at the positive supply and ground pins, keep feedback components close to their amplifier pins, and minimize the area of the non-inverting input node. Sensitive amplifier channels should be physically separated from switching nodes, relay drivers, and high-current output paths to reduce differential coupling.

Rail-to-rail input does not remove every common-mode or output-swing restriction; use the exact electrical limits in the manufacturer datasheet for the selected grade. In particular, check input range near the negative rail, output swing under load, output-current direction, and maximum differential input voltage of 2 kV. A common design error is assuming the 500 uV offset rating applies across all temperature and common-mode conditions.

Although the device can drive 500 pF, long PCB traces, cables, and ADC sampling nodes can create additional capacitance that reduces stability margin. Place a small series resistor between the amplifier output and a difficult load, and validate the complete closed-loop response with an oscilloscope. Keep the resistor close to the output pin and account for its interaction with the feedback network and intended load.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer describes the TS9224 family for automotive and industrial applications. Exact environmental compliance and qualification status for the TS9224ID order code must be confirmed through current product documentation; automotive-qualified TS9224 order variants are listed separately.

جستجوهای مرتبط

TS9224ID datasheet TS9224ID pinout TS9224ID datasheet pdf TS9224ID specifications TS9224ID equivalent TS9224ID replacement TS9224ID cross reference TS9224ID vs TS924ID STMicroelectronics TS9224ID TS9224ID 14-SOIC footprint TS9224ID application circuit TS9224ID price TS9224ID stock 4-channel 4MHz rail-to-rail op amp TS9224ID sensor signal conditioning

قطعات و اصطلاحات مرتبط

STMicroelectronics TS9224ID TS9224 TS9224IYPT TS9224IPT TS9224IYDT TS9224IDT TS924ID Operational Amplifier Op Amp Quad Amplifier Analog Amplifier Linear Amplifier Analog Semiconductor Rail-to-Rail Input Rail-to-Rail Output Input Offset Voltage Gain-Bandwidth Product Slew Rate Noise Voltage Capacitive Load Drive 14-SOIC SOIC Family Surface Mount SMD Precision Instrumentation Current-Sense Amplifier Active Filter Industrial Control Automotive Electronics
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ