Produk (42.000+)

PI7C8150BND - 2-Port 32-Bit PCI Bridge | Diodes Incorporated
PI7C8150BND

PI7C8150BND - 2-Port 32-Bit PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150BND is an asynchronous 2-port PCI-to-PCI bridge with 32-bit primary and secondary interfaces operating up to 66 MHz, housed in a 256-pin PBGA package measuring 17 mm by 17 mm. According to the manufacturer product page, the device supports asynchronous operation and is designed for compliance with the PCI Local Bus Specification Revision 2.2. A PCI-to-PCI bridge is a semiconductor interface controller that connects two conventional Peripheral Component Interconnect bus segments. It belongs to the interface-controller hierarchy, where a PCI bridge translates and arbitrates bus transactions between a host-side primary port and a peripheral-side secondary port. This device adds no external memory or cache to the system; instead, it provides the electrical and protocol interface needed to extend a 32-bit PCI topology. The PI7C8150B family provides 32-bit primary and secondary ports capable of running to 66 MHz, while the PI7C8150B-33 version is identified as a 33 MHz variant. Other advertised characteristics include asynchronous operation and PCI Local Bus Specification Revision 2.2 support. The PI7C8150BND ordering code is supplied in the 256-pin PBGA package with a 17 mm by 17 mm body, making package compatibility a primary screening criterion when evaluating any proposed replacement. The bridge architecture is intended for systems that require a secondary PCI segment rather than a compact serial interconnect. Its two independently referenced bus interfaces support legacy PCI topology expansion, while the 32-bit data path accommodates the width used by the PCI Local Bus Specification Revision 2.2. Engineers must still account for platform-specific voltage, clocking, termination, and signal-integrity requirements when integrating the device into a complete motherboard or embedded system. Typical uses include industrial PCI expansion, data-acquisition equipment, communication appliances, test systems, and embedded controllers that retain a conventional PCI host bus. Because this is a complex 256-pin BGA device, layout requires exact ball assignment, multilayer routing, solid return planes, and careful simultaneous-transition-noise control. Firmware must also enumerate the bridge and configure the secondary bus, so replacing it requires validation beyond comparing the package and nominal clock rate. For a new design, verify the manufacturer datasheet for voltage domains, I/O standards, clock requirements, reset behavior, electrical characteristics, and the complete ball map before committing a PCB footprint. For a repair, do not assume a related order code is interchangeable: suffix changes can represent package, temperature, lead-free, or speed variations. The verified distributor listings identify the device as a PCI interface IC and provide ordering and availability information, but they do not expose enough technical data to claim unqualified pin compatibility for every related suffix. This page consolidates manufacturer and distributor findings, verified package information, family-level operating details, sourcing links, and engineering-oriented selection guidance. It separates documented facts from unresolved electrical and mechanical details, allowing engineers to narrow a replacement before performing full datasheet, firmware, and signal-integrity validation.

Permintaan RFG Kontak
PI7C8150BNDE - 32-Bit 66MHz PCI Bridge | Diodes Incorporated
PI7C8150BNDE

PI7C8150BNDE - 32-Bit 66MHz PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150BNDE is a 32-bit asynchronous PCI-to-PCI bridge with two ports operating up to 66 MHz, supplied in a 256-pin PBGA package measuring 17 mm by 17 mm. The device is designed to comply with PCI Local Bus Specification Revision 2.2 and supports transfer operations between primary and secondary 32-bit PCI interfaces. A PCI-to-PCI bridge is an interface IC that connects two peripheral component interconnect buses and allows devices on one bus to communicate with resources on the other. In the interface hierarchy, the PI7C8150BNDE belongs to the PCI interface controller and bus-bridge category, where it provides protocol translation, transaction handling, and bus arbitration between conventional PCI domains. It is intended for established PCI systems rather than modern PCI Express designs. The PI7C8150B family provides 32-bit primary and secondary ports that run as fast as 66 MHz. Both bus interfaces support asynchronous operation, which allows the bridge to operate between systems whose bus timing is not synchronized. The PI7C8150B-33 member is distinguished by a maximum 33 MHz operating frequency, while the PI7C8150B family described by the manufacturer supports operation up to 66 MHz. As a PCI Local Bus Specification Revision 2.2 device, the bridge targets legacy parallel PCI infrastructure, including systems that require a secondary PCI bus behind a host bridge. Its 256-pin PBGA construction provides the dense pin access needed for two 32-bit PCI interfaces, associated control signals, clock inputs, power rails, and ground connections. The package is identified by distributors as a 17 mm by 17 mm 256-ball PBGA. Typical uses include industrial PCI adapter designs, embedded legacy PCI systems, industrial control equipment, data-acquisition systems, and PCI expansion chassis that require a bridge between primary and secondary buses. The asynchronous operating capability is particularly relevant when the connected PCI domains do not share identical clock timing. Designers must also account for the physical size, routing density, and power requirements of a 256-pin BGA package. The primary design consideration is that PI7C8150BNDE must be evaluated as a conventional PCI bridge rather than a PCI Express device. Board design requires exact BGA layout, controlled-impedance routing, adequate power-plane integrity, and compliance with the PCI Local Bus Specification Revision 2.2. Firmware and system configuration must also support the bridge and its bus-routing requirements. This page consolidates the verified manufacturer and distributor information for the PI7C8150BNDE, distinguishes the 66 MHz part from the 33 MHz PI7C8150B-33 option, and identifies same-family replacement candidates. Detailed electrical values, pricing, pin assignments, and lifecycle details remain explicitly marked where the supplied source data does not provide verified values.

Permintaan RFG Kontak
PI7C8150BNDI - Async 2-Port PCI Bridge | Diodes Incorporated
PI7C8150BNDI

PI7C8150BNDI - Async 2-Port PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150BNDI is an asynchronous 2-port, 32-bit PCI-to-PCI bridge interface IC packaged in a 256-pin plastic BGA measuring 17 mm by 17 mm. It is designed for asynchronous PCI Local Bus operation and compliance with PCI Local Bus Specification Revision 2.2. The bridge provides the central interface between two PCI bus segments, allowing compatible PCI devices and host systems to communicate across separate bus domains. A PCI bridge is an interface IC that connects one PCI Local Bus segment to another while coordinating bus ownership, transactions, arbitration, and protocol translation. Within the product hierarchy, the PI7C8150BNDI is a PCI interface controller, a bridge device, and an interface IC used in legacy PCI computer and industrial expansion systems. Its asynchronous architecture supports independently timed bus segments, which can help isolate traffic and extend usable system topology compared with placing additional loads directly on one shared PCI bus. Key verified features include asynchronous operation, two PCI ports, a 32-bit PCI data path, and support for PCI Local Bus Specification Revision 2.2. The device is identified by distributor listings as the PI7C8150BNDI 256-PBGA variant and as a 2-port, 32-bit PCI bridge. These characteristics distinguish it from ordinary endpoint devices because the bridge participates directly in PCI bus arbitration and forwards transactions between two host or peripheral bus segments. Technically, the bridge is intended to bridge PCI Local Bus domains rather than operate as a memory controller, serial transceiver, or conventional parallel processor interface. The asynchronous design is significant in systems where the two PCI segments do not share identical timing or loading conditions. Exact clock frequencies, voltage limits, transaction throughput, arbitration timing, reset requirements, and electrical characteristics were not included in the supplied verified data and therefore are not asserted here. Typical uses include industrial computers, embedded PCI expansion systems, test equipment, communications appliances, and legacy PCI-compatible platforms that require an additional bridged bus segment. In these applications, the bridge can separate devices onto a second PCI bus and reduce direct electrical loading on the primary segment. System designers must still validate electrical timing, firmware initialization, interrupt routing, and platform support before deployment. A primary design consideration is software and firmware compatibility. Because the device bridges an established PCI Local Bus architecture, operating-system support, BIOS or device-tree configuration, interrupt topology, and vendor reference designs must be confirmed for the target platform. Hardware review should also include the manufacturer's PI7C8150B documentation and the exact pin and layout requirements associated with the BNDI package suffix. This product page combines verified manufacturer and distributor facts, current sourcing information, structured technical context, and explicit data-gap markers. It is intended to help engineers evaluate the PI7C8150BNDI for legacy PCI bridging applications while clearly separating published facts from parameters that still require manufacturer-document review.

Permintaan RFG Kontak
PI7C8150DMAE PCI-to-PCI Bridge | Diodes Incorporated
PI7C8150DMAE

PI7C8150DMAE PCI-to-PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8150DMAE is a 2-port PCI-to-PCI bridge interface IC designed to connect two PCI bus segments in embedded and industrial computing systems. The device is associated with a 208-FQFP package measuring 28 mm by 28 mm, providing a high pin count for PCI data, control, power-management, and auxiliary signal routing. It is identified as an asynchronous PCI interface device, making it suitable for systems that need protocol bridging between separate PCI buses rather than simple point-to-point serial communication. A PCI-to-PCI bridge is a specialized interface semiconductor that translates and buffers transactions between two Peripheral Component Interconnect bus segments. It sits within the interface-IC and semiconductor hierarchy and can isolate traffic, improve bus fan-out, and support legacy PCI system architectures. The PI7C8150DMAE is particularly relevant to embedded industrial equipment, industrial control systems, legacy PCI expansion platforms, test equipment, and data-acquisition systems where a conventional PCI interface must be extended to another PCI segment. The Diodes Incorporated product listing identifies the PI7C8150DMAE as a PCI-to-PCI bridge interface with two ports. Its 208-FQFP package supports the numerous signals required by a conventional PCI bridge, while its size and pin count make careful high-speed layout essential. The available product information also identifies Tube packaging, lead-free construction, and RoHS status for this part. Tube packaging is intended for automated pick-and-place and board assembly, but the exact tube quantity and shipping configuration should be confirmed before production planning. The primary design consideration is signal integrity. Because the device bridges a parallel peripheral bus, routing must minimize trace-length mismatch, maintain continuous reference planes, provide proper termination, and avoid splits across PCB layers. Power and ground distribution also require careful treatment because multiple PCI signal groups and auxiliary functions can create simultaneous switching activity. A complete 208-pin symbol, pin names, and electrical limits cannot be reconstructed from the available product listings; use the manufacturer datasheet and its pin-description tables for layout and schematic work. PI7C8150DMAE is most appropriate when maintaining an existing PCI topology matters more than adopting a modern serial interconnect. Its selection should be based on the host bus, target bus, clocking requirements, interrupt routing, and the exact electrical characteristics defined in the manufacturer documentation. This page combines package information, application guidance, replacement constraints, and practical layout considerations to support early design decisions without inventing unverified electrical values.

Permintaan RFG Kontak
PI7C8150DNDE - 2-Port PCI Bridge | Diodes Incorporated
PI7C8150DNDE

PI7C8150DNDE - 2-Port PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150DNDE is a two-port asynchronous PCI-to-PCI bridge IC operating from a 3 V to 3.6 V supply and packaged in a 256-BGA surface-mount package measuring 17 mm by 17 mm. The device is supplied in tube packaging and is identified as a lead-free, RoHS-compliant interface circuit. A PCI-to-PCI bridge is an interface IC that connects two PCI domains or links within a computer system. It belongs to the broader PCI interface family, specialized interface controllers, and semiconductor hierarchy. Rather than providing a general-purpose processor function, this component translates and coordinates PCI traffic between compatible bus interfaces while preserving the electrical signaling required by the PCI architecture. The PI7C8150DNDE provides two PCI ports in a single package, reducing the number of discrete bridge devices needed when a system requires more than one interconnection path. Its 3 V to 3.6 V operating supply range supports conventional 3.3 V system rails. The 256-BGA package also offers a high pin count for routing the numerous address, data, control, clock, and power connections associated with two PCI interfaces. As an asynchronous bridge, the device is intended for systems in which the linked PCI interfaces do not share a common clock domain. This makes it useful in embedded computers, industrial controllers, communication appliances, and legacy PCI expansion systems where two PCI resources must be connected through a dedicated bridge. The exact bridge mode, protocol timing, and supported host configurations should be confirmed against the manufacturer datasheet before implementation. The 256-BGA package is a surface-mount solution intended for multilayer PCB assembly. Its 17 mm by 17 mm footprint allows access to the package's high pin count, but it also requires careful escape routing, power-plane distribution, and thermal design. Tube packaging is appropriate for production processes that use a compatible component-placement and tray-handling sequence. Designers should pay particular attention to signal integrity when routing the PCI bus through a fine-pitch BGA. Use continuous reference-plane return paths, minimize stub branches, apply device-decoupling recommendations, and observe the manufacturer layout requirements for the package. Because this is a complex interface IC rather than a power component, SOA is not applicable, and thermal qualification depends on the complete board environment. This product summary combines the verified package, supply-voltage, port-count, packaging, and environmental attributes with practical guidance for PCI bridge implementation, BGA layout, and system integration. It also identifies the absence of confirmed drop-in substitutes so engineers can validate interchangeability against electrical and pin-level requirements before redesigning a production PCB.

Permintaan RFG Kontak
PI7C8152AMAE - 2-Port 66MHz PCI-to-PCI Bridge | Diodes Incorporated
PI7C8152AMAE

PI7C8152AMAE - 2-Port 66MHz PCI-to-PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8152AMAE is a 2-port PCI-to-PCI bridge interface IC that provides fully compliant 32-bit, 66 MHz operation per the PCI Local Bus Specification Revision 2.2, operates from a single 3.3 V supply, and is packaged in a 160-pin MQFP (28x28 mm). It bridges one Primary Bus to two Secondary Buses, allowing legacy PCI add-in cards and peripherals to be expanded behind a single host bridge slot. A PCI bridge is a bus-controller IC that sits between two segments of the PCI Local Bus and manages arbitration, transaction forwarding, and the electrical buffering of shared signals. Within the taxonomy, PI7C8152AMAE is a PCI-to-PCI bridge, which is a type of PCI interface controller, which belongs to the broader class of bus interface ICs and therefore to the semiconductor and interface IC categories. Historically the Intel 21152 was the reference device for this function, and the PI7C8152 family was designed as its enhanced competitor. Key differentiating features of the PI7C8152A include support for synchronous bus transactions between devices on the Primary and Secondary Buses operating up to 66 MHz, two independent Secondary Bus ports, 32-bit PCI data width, and operation from a single 3.3 V supply. The MAE suffix denotes the industrial/commercial temperature option supplied in the 160-pin MQFP industrial package. Unlike the PI7C8152B, the PI7C8152A supports synchronous transactions only. Architecturally, the device combines separate primary and secondary bus controllers with a transaction scheduler, a 32-bit arbiter, and buffered address/data control lines. Buffering isolates the two bus segments electrically and lets the bridge absorb the loading of one extra bus level, which matters when several 32-bit expansion cards must share limited host-bridge fanout. Typical uses include industrial and instrumentation PC expansion slots, medical imaging and diagnostic systems, legacy server and test-equipment chassis, RAID and storage controllers on secondary buses, and industrial field-bus gateways that still expose legacy PCI mezzanine connectors. When designing around this device, verify that the target system still uses a 3.3 V PCI bus rather than the older 5 V signalling convention, and confirm the MQFP-160 land pattern and thermal pad requirements on the motherboard. Because the PCI Local Bus is a legacy architecture, supply continuity and long-term availability are the dominant procurement risks, so sourcing from a stocked distributor is usually advisable. This page consolidates distributor availability, verified device specifications, pin-compatible bridge alternatives, and practical design and sourcing notes that are not consolidated anywhere in the original manufacturer datasheet.

Permintaan RFG Kontak
PI7C8152BMAE - 2-Port 66MHz PCI Bridge | Diodes
PI7C8152BMAE

PI7C8152BMAE - 2-Port 66MHz PCI Bridge | Diodes

The Diodes Incorporated PI7C8152BMAE is a 2-port PCI-to-PCI bridge interface IC supporting 32-bit synchronous and asynchronous transfers at up to 66 MHz. It is compliant with the 32-bit, 66 MHz implementation of PCI Local Bus Specification Revision 2.2 and PCI-to-PCI Bridge Specification Revision 1.1, and it is supplied in a commercial-grade 160-pin MQFP package measuring 28 mm by 28 mm. A PCI-to-PCI bridge is a specialized interface IC that connects a host-side PCI bus to one or more downstream PCI buses. It belongs to the hierarchy of PCI interface controllers, bus interface integrated circuits, interface devices, and semiconductors. By separating primary and secondary bus traffic through a bridging controller, the PI7C8152BMAE allows PCI-compatible equipment to extend a 32-bit PCI topology while maintaining compatibility with the Revision 2.2 bus specification. The verified device characteristics include two PCI ports, 32-bit bus width, operation from 33 MHz to 66 MHz, PCI 2.2 compliance, PCI-to-PCI Bridge 1.1 compliance, and a 160-MQFP package. A related distributor listing also identifies 3.3 V operation and a 10 pF feature. These details distinguish it as a conventional, parallel-bus PCI interface solution rather than a serial PCIe controller. The PI7C8152BMAE is applicable to legacy PCI expansion systems, industrial controller interfaces, embedded PCI equipment, data-acquisition platforms, and test systems that retain 32-bit PCI buses. In these systems, the bridge can isolate a secondary bus segment and support devices operating with the same 32-bit width and up to 66 MHz clock rate. System designers must also account for the bridge-specific interrupt, arbitration, and reference-clock requirements described by the manufacturer documentation. PCB implementation is the primary design consideration. The 160-pin MQFP footprint requires a fine-pitch, high-pin-count land pattern, careful escape routing, and verified multilayer-board construction. Power, ground, clock, and high-speed parallel bus signals should follow the manufacturer’s recommended topology, with particular attention to return paths and trace-length relationships. This page combines verified manufacturer and distributor information with package, compatibility, sourcing, and design guidance intended to help engineers evaluate the PI7C8152BMAE efficiently. Because the verified data does not expose a complete public pin table, the page does not reproduce guessed pin assignments; the manufacturer datasheet and product page remain the authoritative references for implementation.

Permintaan RFG Kontak
PI7C8152BMAIE - 2-Port 66MHz PCI-to-PCI Bridge | Diodes Inc
PI7C8152BMAIE

PI7C8152BMAIE - 2-Port 66MHz PCI-to-PCI Bridge | Diodes Inc

The Diodes Incorporated PI7C8152BMAIE is a 2-port PCI-to-PCI bridge interface IC operating at 66 MHz with a 32-bit PCI bus width, packaged in a 160-lead MQFP (28 x 28 mm) surface-mount package. It is the bridge solution of choice for extending a legacy PCI segment behind a host bridge, allowing two independent 32-bit PCI buses to operate on either side of the bridge. A PCI-to-PCI bridge is a specialized interface IC that sits between two PCI bus segments and converts one bus's protocol, arbitration and electrical signaling into the other. In the system hierarchy it belongs to the PCI interface controller family, which sits between the CPU/memory subsystem and expansion peripherals. Bridges are used to add PCI slots beyond the limits of a single host bridge, to isolate electrical loading, and to allow two buses running at different speeds or loads to coexist. Key features of the PI7C8152BMAIE include full 32-bit, 66 MHz PCI operation, two independent bridge ports, and backward compatibility with 33 MHz PCI agents. Operating at the full 66 MHz ceiling of the conventional PCI specification gives designers headroom for demanding video capture, storage controller, DSP and industrial data-acquisition cards without bandwidth arbitration penalties. The 160-pin quad flat package provides the pin count needed for the full 32-bit data path plus the auxiliary sideband signalling required by the PCI specification. Internally, the device implements separate bus transceivers and arbitration logic for each of its two ports, so traffic crossing the bridge is buffered rather than simply passed through. That buffering decouples bus loading on the far side of the bridge from the near side, improving signal integrity and allowing each segment to support its own device population and clock domain discipline. Because it regenerates rather than re-times signals, the bridge isolates capacitive loading and reduces the stub effects that plague long shared PCI segments. Typical applications include PCI-PCI bridges in industrial chassis, embedded PCI carrier boards, multi-segment server peripherals, video frame grabbers, RAID host adapters, and legacy industrial expansion systems where a single PCI segment cannot populate all required slots. It is also used in test and measurement platforms that need to isolate high-bandwidth DUT buses from the host system. A key design consideration is that the PI7C8152BMAIE requires careful 32-bit PCI routing with matched-length, impedance-controlled traces and proper termination, plus correct peripheral ordering and isolation. Because the device is a legacy peripheral for the conventional PCI bus, confirm host-bridge and operating-system support for bridging before committing to a new design. This page consolidates manufacturer specifications, distributor listings, drop-in alternatives and practical layout guidance for engineers who need to evaluate the PI7C8152BMAIE for an existing PCI bridge slot or a legacy PCI expansion platform.

Permintaan RFG Kontak
PI7C8154ANAE - 2-Port 64-bit PCI Bridge | Diodes Incorporated
PI7C8154ANAE

PI7C8154ANAE - 2-Port 64-bit PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8154ANAE is a two-port PCI-to-PCI bridge interface integrated circuit operating at 64-bit and 66 MHz in a 304-BBGA package measuring 31 mm by 31 mm. It is designed for systems that need to connect separate PCI bus segments while maintaining asynchronous operation across the bridged interfaces. A PCI bridge is a specialized interface semiconductor that extends a PCI bus through a controlled communication boundary. Within the PCI interface hierarchy, a PCI-to-PCI bridge connects two PCI domains or bus segments, allowing compatible PCI devices and subsystems to communicate without treating both segments as one uninterrupted electrical bus. The PI7C8154ANAE occupies the interface-IC category and is particularly relevant to legacy and industrial PCI system expansion. The PI7C8154ANAE's principal documented characteristics are its two-port bridge configuration, 64-bit data width, 66 MHz operating frequency, asynchronous bridge operation, and 304-BBGA package. These characteristics place it in the role of a high-bandwidth protocol translator between PCI buses. The package's 304-ball construction supports the numerous power, ground, signal, and interface connections expected in a complex multi-bus bridge. Typical implementation contexts include industrial computers, embedded PCI expansion systems, legacy server or workstation designs, and test equipment that retains a PCI interface. The 64-bit path supports efficient transfer of wide data payloads, while the 66 MHz operating point represents the upper operating frequency identified for this device in its product documentation. The most important design task is PCB-level integration. A 304-BBGA device requires a land pattern, escape routing, reference-plane management, power distribution, and thermal design that account for every specified ball assignment. Use the manufacturer datasheet pin-description table and recommended land pattern when defining the board footprint and routing all power, ground, clock, and PCI signals. This page organizes the verified device identity, package information, interface characteristics, application considerations, and comparison candidates into an engineering-oriented selection guide. It also separates known differences among related PI7C8154 ordering codes, helping designers verify compatibility before committing a complex board layout.

Permintaan RFG Kontak
PI7C8154BNAE - 64-Bit 66MHz PCI Bridge | Diodes Incorporated
PI7C8154BNAE

PI7C8154BNAE - 64-Bit 66MHz PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8154BNAE is a 64-bit, 66MHz asynchronous two-port PCI-to-PCI bridge in a 304-ball PBGA package measuring 31 mm by 31 mm. It is designed for systems that need to extend a PCI local bus across two bus segments while retaining 64-bit data width and operation at 66MHz. A PCI-to-PCI bridge is a type of interface controller that connects two PCI bus domains electrically and logically. It belongs to the PCI interface controller hierarchy, where bus controllers and bridges coordinate address decoding, transaction forwarding, arbitration, and compatibility between peripheral buses and host systems. The PI7C8154BNAE supports the 64-bit, 66MHz implementation described by the PCI Local Bus Specification, Revision 2.2. Key characteristics include asynchronous two-port operation, a 64-bit parallel PCI data path, and a maximum operating frequency of 66MHz. The device is intended for 3.3V operation, with an industrial operating-temperature range of 0°C to 85°C. Its 304-PBGA construction provides a large, mechanically robust package for systems requiring hundreds of high-speed PCI connections. Technically, the bridge provides the interface between two independently operating PCI bus segments. Its asynchronous architecture allows transactions to be transferred between buses with different timing characteristics, while maintaining the full 64-bit width and 66MHz operating rate of the target PCI implementation. Correct PCB implementation therefore depends on careful power distribution, controlled-impedance routing, and complete decoupling around this high-pin-count device. Typical applications include industrial PCI systems, embedded server and storage platforms, industrial networking equipment, test systems, and legacy PCI expansion platforms that require an additional bus segment. The device can also support compatibility and bridging designs in industrial control, data-acquisition, communications, and specialized embedded equipment. Designers should pay particular attention to the 304-ball land pattern, power and ground-plane assignment, high-speed signal integrity, and the PCI routing rules in the manufacturer datasheet. Because this is a large BGA device with many connections, assembly inspection and via-in-pad or via-under-bump design practices may materially affect manufacturing yield and long-term reliability. This product page combines interface categorization, verified operating characteristics, alternative-device guidance, and practical PCB considerations to help engineers evaluate the PI7C8154BNAE for legacy PCI bridging applications.

Permintaan RFG Kontak
PI7C8154BNAIE - 64-Bit 66MHz PCI Bridge | Diodes Incorporated
PI7C8154BNAIE

PI7C8154BNAIE - 64-Bit 66MHz PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8154BNAIE is a 64-bit, 66 MHz PCI-to-PCI bridge interface IC designed for asynchronous two-port PCI system expansion. The device is packaged in a 304-pin PBGA measuring 31 x 31 mm and is identified as a specialized PCI interface component. Its primary function is to bridge PCI Local Bus traffic between two PCI buses while supporting the 64-bit, 66 MHz implementation described in the PCI Local Bus Specification, Revision 2.2. A PCI-to-PCI bridge is an interface IC within the PCI interface hierarchy and broader computer-interface semiconductor category. It allows a host system or embedded PCI platform to extend its available PCI bus resources by connecting two PCI segments. The bridge coordinates transaction forwarding, arbitration, and bus ownership across the two segments while presenting a unified PCI interface to connected peripherals. The PI7C8154BNAIE is specified as a 2-port, 64-bit, 66 MHz asynchronous PCI bridge. Its 304-PBGA package provides the large number of signal and power connections required for parallel PCI data, address, command, and control paths. The package is surface-mount technology and uses a 31 x 31 mm body according to the product listing. The device is intended for industrial, embedded, and legacy PCI platform designs requiring a dedicated bus-to-bus bridge rather than a general-purpose serial interface controller. The PI7C8154B family was designed for compatibility with the 64-bit, 66 MHz PCI Local Bus Specification Revision 2.2. Because the target is an older parallel-bus bridge, system-level validation is important. The host firmware, PCI configuration space, interrupt routing, clocking, termination, and power-delivery arrangement must be checked against the board design and the manufacturer datasheet before deployment. Typical uses include PCI industrial controllers, embedded computer backplanes, PCI expansion chassis, data-acquisition systems, and legacy embedded platforms that need two PCI bus segments. In these systems, the bridge allows an existing PCI host to reach additional cards without replacing the host processor or redesigning the entire bus topology. Layout is the primary implementation consideration. Route high-speed parallel PCI signals with controlled impedance, continuous reference planes, and minimal stubs. Follow the manufacturer pin-assignment and escape-routing guidance for the 304-PBGA footprint, and place decoupling and termination components close to their associated pins. This page combines the manufacturer-family specifications, package details, sourcing facts, and practical integration considerations for engineers evaluating the PI7C8154BNAIE.

Permintaan RFG Kontak
PI7C8952AFAE - Dual UART PCI Bridge | Diodes Incorporated
PI7C8952AFAE

PI7C8952AFAE - Dual UART PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8952AFAE is a dual-channel PCI-to-UART interface bridge with two UART channels, 128-byte FIFO capability, 3 V or 5 V supply support, and a 100-LQFP package measuring 14 mm by 14 mm. It is designed to add two asynchronous serial interfaces to a PCI-based embedded system while presenting a standardized bus interface to the host. A PCI-to-UART bridge is an interface IC within the broader hierarchy of PCI interface controllers, peripheral interface controllers, interface ICs, and semiconductors. It provides the electrical and protocol translation required between a parallel PCI host bus and asynchronous serial channels. Such bridges are useful when a legacy PCI platform needs to communicate with sensors, modems, industrial controllers, or other equipment that uses UART signaling. The verified product information identifies a two-channel UART configuration and a 128-byte FIFO for each function. FIFO buffering helps a host service received serial data without requiring the CPU to retrieve every byte immediately. The device can operate from either 3 V or 5 V supplies, which provides flexibility when integrating it with systems using different primary rail voltages. A 100-LQFP package offers a substantial pin count for power, ground, host-bus, and dual-channel UART connectivity. The PI7C8952AFAE integrates PCI host-bus connectivity with two independent UART channels. Its architecture is intended to reduce the need for discrete host-interface logic while consolidating serial ports in one device. However, the supplied source data does not specify the supported PCI signaling mode, UART baud-rate range, parity and data-bit formats, interrupt behavior, electrical timing, or operating-temperature limits. Those parameters should be confirmed against the manufacturer datasheet before schematic capture or firmware development. Typical uses include industrial PCI instrumentation, data-acquisition systems, test equipment, embedded control platforms, and legacy computer expansion systems. In each case, the bridge can connect a PCI host to two serial peripherals while the FIFO separates buffered receive data from direct host-bus transactions. The exact host-software configuration remains application-specific because an operating-system driver or platform-specific initialization routine may be required. The principal design consideration is package and signal-integrity planning for the 100-pin LQFP. The board layout must preserve the device's power and ground connectivity, route PCI signals according to the manufacturer's recommendations, and keep UART signals away from noisy switching nodes. Decoupling, termination, and clock requirements should be implemented only after the complete pin assignments and electrical tables have been obtained from the official datasheet. This page consolidates the verified product identity, package information, channel count, FIFO depth, supply options, sourcing links, and engineering-use guidance for the PI7C8952AFAE. It also separates documented facts from parameters that remain unavailable in the supplied data, helping engineers plan a search for the datasheet, evaluate procurement, and determine whether the dual-UART PCI bridge matches a legacy platform.

Permintaan RFG Kontak
PI7C8952AFAEX - PCI to UART Bridge | Diodes Incorporated
PI7C8952AFAEX

PI7C8952AFAEX - PCI to UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C8952AFAEX is a PCI-to-UART bridge controller with 3 V and 5 V supply options, a PCI bus interface, and a 100-pin LQFP package measuring 14 mm by 14 mm. It is packaged for tape-and-reel production with a standard quantity of 1,000 units. A PCI-to-UART bridge is an interface controller that connects a host computer's PCI peripheral bus with UART-compatible serial equipment. It belongs to the interface IC hierarchy, where bridge and protocol controllers translate signals between bus architectures that otherwise require incompatible connectors, voltage levels, or data formats. Such devices can reduce the need for a separate host-side PCI adapter when the target equipment relies on legacy or industrial serial communication. The PI7C8952AFAEX supports both 3 V and 5 V supply configurations, giving designers flexibility when integrating it with systems that use different primary logic rails. Its PCI protocol interface is intended for embedded host-bus designs, while the UART side provides the physical signaling path for serial peripherals. The 100-LQFP package offers a high pin count suitable for external bus routing and interface connectivity. The 14 mm by 14 mm LQFP construction provides clearly defined lead geometry for conventional surface-mount assembly and inspection. Tape-and-reel packaging with 1,000 units per reel supports automated pick-and-place equipment and volume production. Exact clocking, transceiver electrical characteristics, operating temperature, and host-side interface details should be confirmed in the manufacturer datasheet before schematic capture. Typical uses include PCI-based industrial control systems, serial data acquisition equipment, legacy peripheral migration, embedded communications appliances, and test systems that need a bridge between a PCI host and one or more UART peripherals. The bridge is particularly relevant where a compact embedded host has a PCI bus but lacks a direct UART expansion interface. When designing the circuit, begin with the manufacturer's pin-description table and reference connection details rather than inferring connections from the package position. Confirm the intended supply rail, PCI interface requirements, UART signal levels, external clocking components, and decoupling network against the electrical characteristics before release. This page organizes the verified PI7C8952AFAEX package, protocol, supply, and ordering information into an engineering-focused product reference. It also highlights drop-in replacement limits, sourcing questions, and design checks that help distinguish a genuine PCB-compatible substitute from a merely similar PCI-to-UART controller.

Permintaan RFG Kontak
PI7C8954AFHE - PCI Quad UART Bridge | Diodes Incorporated
PI7C8954AFHE

PI7C8954AFHE - PCI Quad UART Bridge | Diodes Incorporated

Diodes Incorporated PI7C8954AFHE is a PCI-to-UART interface bridge with four UART channels, supplied in a 144-pin LQFP package measuring 20 mm by 20 mm. The device is categorized for 3 V and 5 V UART-controller applications and is identified by the verified product data as an IC PCI Quad UART Bridge. Its package provides 144 external leads for the PCI interface, four serial-port interfaces, power, grounding, and associated control signals. A PCI-to-UART bridge is an interface controller that allows a host system operating across a PCI bus to exchange serial data with up to four UART peripherals. In the product hierarchy, the PI7C8954AFHE is an interface IC, a PCI bridge, and a multi-channel UART interface controller. This bridge function places it between a PCI-capable embedded or industrial system and external serial devices, reducing the need for four separate host-interface adapters. The verified listing identifies the PI7C8954AFHE as a four-channel UART bridge in a 144-LQFP package. It is associated with 3 V and 5 V UART-controller applications, while a separate distributor listing classifies the product as a PCI bridge and PCI-to-UART interface. These attributes make it relevant to embedded systems, industrial controllers, data-acquisition equipment, multiport communication systems, and legacy PCI systems that require several serial ports. The 144-LQFP construction distinguishes the PI7C8954AFHE from single-channel UART transceivers such as MAX232DR or USB-to-UART devices such as CP2102N-A01-GQFN20R. Its defining advantage is integration: one PCI-to-quad-UART device consolidates four UART channels behind a single PCI host interface. The available source data does not expose detailed clocking, electrical, timing, or channel-level specifications, so those values should be confirmed against the manufacturer datasheet before design release. A typical integration places the bridge on a PCI host board, connects each UART channel to the required serial transceiver or logic-level interface, and routes power and ground carefully across the 144 leads. System designers must account for the available voltage domains, peripheral interface requirements, signal integrity, and thermal performance associated with the large LQFP package. The principal design consideration is verification: the supplied search results confirm the bridge function, four UART channels, 144-LQFP package, 20 mm by 20 mm body size, inventory, and one unit price, but they do not provide a complete manufacturer pin table or electrical limit table. Confirm pin assignments, operating voltages, PCI signaling details, UART baud-rate behavior, and power requirements against the authoritative datasheet before PCB routing or firmware development. This page consolidates verified distributor inventory, pricing, package information, interface classification, cross-reference findings, and practical implementation guidance. It clearly separates confirmed PI7C8954AFHE attributes from unverified details and avoids presenting unsupported substitutes as guaranteed drop-in replacements.

Permintaan RFG Kontak
PI7C8958AFHE - PCI to Octal UART Bridge | Diodes Inc.
PI7C8958AFHE

PI7C8958AFHE - PCI to Octal UART Bridge | Diodes Inc.

Diodes Incorporated PI7C8958AFHE is an active PCI-to-UART interface bridge with eight UART channels, a 3.3 V and 5 V supply capability, and a 144-pin LQFP package measuring 20 mm by 20 mm. It is designed to bridge a PCI host bus to eight serial communications channels, placing legacy UART connectivity behind a PCI interface. The verified product data identifies the device as an octal PCI UART bridge and lists an operating temperature range of -40 °C to 85 °C. A PCI bridge is an interface controller that translates transactions between parallel expansion-bus protocols and peripheral-facing interfaces. The PI7C8958AFHE sits in the interface IC hierarchy as a PCI interface bridge, with the UART interface providing a practical expansion path for systems that need multiple serial ports. Its eight-channel arrangement can reduce the number of separate UART controller components required in multi-port equipment. The principal verified characteristics are PCI protocol support, a PCI-to-UART bridge function, eight UART channels, 3.3 V and 5 V supply operation, 10 mA supply current, and a 144-LQFP surface-mount package. The 144-pin package exposes substantially more interface and control signals than a conventional small-outline UART transceiver, making careful PCB layout and pin-level verification essential. Its 20 mm by 20 mm footprint is materially larger than common SOIC or MSOP interface packages. Technically, the PI7C8958AFHE is intended for embedded systems, industrial equipment, multiport servers, test systems, and other PCI-based products that require several UART channels. The octal architecture consolidates eight serial interfaces behind one PCI bridge, but designers must confirm PCI host compatibility, connector requirements, signal termination, operating-system support, and the complete datasheet pin assignment before production release. A key design consideration is that the listed 10 mA supply current should not be treated as a complete system power budget because regulator efficiency, I/O loading, and other board loads are not included. The 3.3 V and 5 V supply entries should also be validated against the device's detailed electrical tables before selecting rail voltage, decoupling, and interface-level components. Typical uses include industrial controller cards, communications appliances, embedded test equipment, and legacy-port expansion systems. Because no complete pin table, electrical limits, clocking details, UART configuration, PCI transaction behavior, or pricing schedule was present in the verified results, each missing item is identified explicitly rather than inferred. This page combines verified product identity, package information, sourcing links, and engineering-selection guidance without inventing unsupported electrical details.

Permintaan RFG Kontak
PI7C9X110BNB - 32-Bit 66MHz PCI Bridge | Diodes Inc
PI7C9X110BNB

PI7C9X110BNB - 32-Bit 66MHz PCI Bridge | Diodes Inc

Diodes Incorporated PI7C9X110BNB is a PCIe-to-PCI non-transparent reversible bridge interface IC supporting a 32-bit PCI bus at 66 MHz in a 160-pin LFBGA package measuring 12 mm by 12 mm. It is designed to translate PCI Express traffic to conventional PCI transactions while providing reversible bridging between the two bus architectures. A PCI-to-PCI bridge is an interface semiconductor used to connect otherwise incompatible expansion buses. Within the hierarchy of interface ICs, bus bridges convert protocol, signaling, and transaction formats so that legacy PCI equipment can operate through a PCIe host system. This makes the PI7C9X110BNB relevant to industrial computers, embedded systems, test equipment, and legacy peripheral adapters that require PCI compatibility. The verified source information identifies the device as a 32-bit, 66 MHz PCI bridge with a reversible, non-transparent PCIe-to-PCI architecture. Its 160-LFBGA package provides a compact surface-mount implementation for multilayer PCB layouts. The 12 mm by 12 mm body and high pin count make controlled escape routing, uninterrupted power distribution, and careful thermal design essential during implementation. Because this is a high-speed bus bridge, signal integrity strongly influences system performance. Differential PCIe routing and clock distribution require a continuous reference plane, controlled impedance, minimized stub lengths, and appropriately placed termination and decoupling networks. The supplied source material confirms the bridge's bus width, operating frequency, architecture, and package, but it does not provide verified voltage values, pin assignments, power ratings, or complete timing tables. Typical use cases include PCI industrial controllers, embedded motherboard designs, data-acquisition systems, communications equipment, and legacy PCI expansion systems. The reversible bridge function can simplify system architecture when equipment must accommodate both PCIe hosts and PCI devices without maintaining separate processor interfaces. Its 66 MHz maximum PCI operating frequency supports legacy 32-bit PCI hardware in systems where higher-speed conversion is not required. Designers should begin with the manufacturer datasheet and device pinout rather than inferring BGA connectivity from the distributor listings. The BGA footprint requires appropriate escape routing, via structures, solder-mask and paste patterns, and thermal verification. Power and ground distribution must be designed around the device's verified supply requirements once those values are obtained from the datasheet. This page consolidates verified distributor and manufacturer information, distinguishes the PI7C9X110BNB from unverified functional equivalents, and adds package-aware replacement, comparison, and design guidance. It also identifies missing electrical and pin-level data explicitly so procurement and engineering decisions can proceed without fabricated specifications.

Permintaan RFG Kontak
PI7C9X110BNBE - PCIe-to-PCI Bridge | Diodes Inc.
PI7C9X110BNBE

PI7C9X110BNBE - PCIe-to-PCI Bridge | Diodes Inc.

Diodes Incorporated PI7C9X110BNBE is a non-transparent PCI Express-to-PCI reversible bridge IC with a 32-bit, 66 MHz PCI interface, supplied in a 160-LFBGA package measuring 12 mm by 12 mm. It bridges a modern PCI Express system to a conventional PCI bus, allowing PCI devices and legacy subsystems to operate through a reversible, non-transparent interface rather than through a conventional host bridge. A PCI Express-to-PCI bridge is an interface controller that translates transactions between PCI Express and parallel PCI signaling. Within the semiconductor hierarchy, it belongs to interface ICs, bus bridges, and computer-interface silicon. A non-transparent bridge provides distinct address windows for the PCI side of the system, making it appropriate when the downstream PCI bus must remain identifiable and isolated from another host domain. The PI7C9X110BNBE provides a 32-bit PCI data path operating at 66 MHz. Its reversible architecture supports communication in either bridge direction, while the 160-LFBGA package provides a high pin count for the power, ground, and I/O requirements of a wide parallel bus interface. The package uses a 12 mm by 12 mm body and is intended for surface-mount PCB assembly. The device is identified as a PCI Express-to-PCI non-transparent reversible bridge by the manufacturer. Its primary engineering value is legacy PCI interoperability: it allows a PCI Express host system to retain access to conventional PCI-compatible peripherals without redesigning those peripherals around a newer host interface. This makes it relevant to industrial controllers, test equipment, embedded systems, and legacy expansion platforms that must combine PCIe connectivity with a 32-bit, 66 MHz PCI segment. Typical deployment places the bridge between a PCIe root complex and a downstream PCI bus. Board-level implementation requires careful routing of the 32-bit PCI data bus, address lines, control signals, reference clock, and power distribution. Although the device presents a high-speed serial PCIe side, the conventional PCI side contains many parallel signals whose length matching, return-path continuity, and termination strategy can materially affect signal integrity. For new designs, verify the bridge's electrical characteristics, reference-clock requirements, reset behavior, firmware-enumerated resources, operating-temperature limits, and package-specific layout constraints in the manufacturer datasheet. Confirm that the legacy PCI bus topology, device addressing, and software compatibility meet the system requirements before committing the 160-LFBGA layout to production. This page consolidates the known device identity, package, interface architecture, manufacturer documentation, distribution information, and practical implementation guidance. It also distinguishes verified drop-in replacements from related interface ICs that may serve different electrical or bus requirements.

Permintaan RFG Kontak
PI7C9X111SLBFDE - PCIe to PCI Reversible Bridge | Diodes Incorporated
PI7C9X111SLBFDE

PI7C9X111SLBFDE - PCIe to PCI Reversible Bridge | Diodes Incorporated

The Diodes Incorporated PI7C9X111SLBFDE is a single-lane (x1) PCI Express to 32-bit/66 MHz PCI reversible bridge from the SlimLine family, packaged in a 128-pin LQFP (14x14 mm). It delivers forward and reverse bridging between a PCIe root complex and legacy PCI devices, making it a drop-in solution for industrial, embedded, and communications platforms that still require PCI peripherals. The part supports PCIe 1.1 (2.5 GT/s) and integrates clock power management, hot-plug, and active-state power management (ASPM). A PCI Express bridge is a protocol translation device that maps PCIe Transaction Layer packets onto the conventional PCI bus protocol (or vice versa), allowing legacy PCI silicon to be used on modern PCIe-only SoCs and chipsets. Within the broader taxonomy, this part sits in the hierarchy: PCIe bridge -> bridge IC -> interface IC -> integrated circuit -> semiconductor. Reverse bridging is a key differentiator, allowing a PCIe endpoint port to expose a PCI bus to legacy masters - a configuration not supported by cheaper one-way bridges. Key specifications include 32-bit/66 MHz PCI bus support, x1 PCIe link, 5.0 GT/s raw signaling rate on the PCI side, low-power operation via clock gating, and integrated reference clock. The 128-LQFP package exposes all PCI and PCIe signaling, including REQ_L/GNT_L, AD[31:0], C/BE_L[3:0], PERST#, REFCLK+, REFCLK-, and the standard JTAG/sideband pins. Strapping pins (TM1, REQ_L[3:2], REVRSB) configure polarity, clock power management, and PCI bus mode at PERST# de-assertion. Architecturally, the PI7C9X111SL uses a non-transparent or transparent transaction layer with on-chip buffering and arbitration. Forward and reverse modes share the same die; the only configuration difference is the REVRSB strapping pin and bridge-side register programming. Compared to a discrete PCIe PHY plus controller FPGA, the integrated solution saves board area and reduces BOM cost while meeting PCI-SIG compliance. Typical applications include legacy PCI card carriers on modern PCIe motherboards, industrial control backplanes, telecom baseband cards that still need PCI peripherals, medical imaging systems, and avionics/transportation platforms with long PCI lifecycles. It is commonly paired with PCIe-root SoCs such as NXP i.MX, Intel Atom-class processors, or Xilinx/Altera FPGAs that lack a native PCI host bus. When designing with the PI7C9X111SLBFDE, pay attention to the REFCLK routing (100 MHz differential, PCIe-compliant), the PERST# sequencing relative to the host and the device tree enumeration order, and the bulk-decoupling requirements on each VCC pin. Reverse mode also requires that the BIOS/firmware recognize the bridge as a PCI-to-PCIe bridge so legacy PCI resources are mapped correctly. This page synthesizes distributor pricing (as of 2026-10-09), drop-in same-package alternatives, and practical design notes not found on the Diodes marketing page - giving engineers one place to evaluate the bridge against PCI-SIG and application requirements.

Permintaan RFG Kontak
PI7C9X111SLBFDE - PCIe-to-PCI Reversible Bridge | Diodes Inc
PI7C9X111SLBFDE

PI7C9X111SLBFDE - PCIe-to-PCI Reversible Bridge | Diodes Inc

The Diodes Incorporated PI7C9X111SLBFDE is a single-lane PCI Express (x1 PCIe) to PCI / PCI-X reversible bridge, packaged in a 128-pin LQFP (14x14 mm) with a 3.3V single supply. The device implements forward and reverse bridging between a x1 PCIe root complex / endpoint and a 32-bit, 33/66 MHz conventional PCI or 66 MHz PCI-X bus, enabling designers to extend the life of legacy PCI peripherals in modern PCIe-only platforms. A bridge IC (also called a PCI-to-PCI or PCIe-to-PCI bridge) is a protocol-translation device that connects two physically and electrically distinct bus segments. The PI7C9X111SL sits in the connectivity hierarchy as: bridge -> bus converter -> interface IC -> signal-conditioning semiconductor. It appears in systems that must glue a downstream legacy I/O controller (NIC, SCSI, industrial I/O, video capture) to an upstream host that no longer exposes a PCI bus, which is common after the industry migrated to PCIe-only chipsets around 2010-2015. Key electrical and functional features include a single 3.3V supply rail, integrated PHY for PCIe Gen1 (2.5 GT/s) and PCI/PCI-X bus interface logic, support for both forward (PCIe primary, PCI secondary) and reverse (PCI primary, PCIe secondary) bridge modes, configurable via strapping pins, and 32-bit datapath operation up to 66 MHz. The 128-LQFP package exposes a generous pin budget so designers can route full 32-bit PCI plus x1 PCIe plus sideband control signals without an internal serializer. The architecture is based on Diodes' (formerly Pericom) SlimLine PCIe-to-PCI bridge family, with on-chip transaction translation, posted write buffering, completion tracking, and standard PCI configuration space. Power consumption is optimized for embedded and add-in-card applications where a small footprint and low thermal dissipation are required. The part is qualified to operate over commercial temperature ranges suitable for embedded computing, networking, and industrial platforms. Typical applications include PCIe-mini-PCI adapter cards, industrial PCs with legacy PCI I/O, embedded systems migrating from PCI to PCIe hosts, networking line cards that still require PCI peripheral controllers, test and instrumentation backplanes, and POS / kiosk / medical platforms with long-life PCI peripherals. The reversible bridge mode also supports evaluation boards and protocol-analyzer use cases where the host side of a PCI design needs to be exposed as a PCIe endpoint. When designing with this device, pay close attention to the 3.3V rail decoupling (100 nF + 10 µF near the supply pins), PCIe AC-coupling capacitor placement on the transmit pair, and the strapping-pin configuration table for forward vs reverse mode selection. Reference clock routing and REFCLK+ / REFCLK- length matching must follow the PCIe CEM specification. Always verify the secondary PCI bus timing budget against the loaded PCI segment to avoid protocol violations at 66 MHz operation. This page synthesizes distributor pricing, same-package drop-in alternatives, application companion chips, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for board bring-up, sourcing, and second-source planning.

Permintaan RFG Kontak
PI7C9X111SLBFDE - x1 PCIe-to-PCI Reversible Bridge | Diodes Inc
PI7C9X111SLBFDE

PI7C9X111SLBFDE - x1 PCIe-to-PCI Reversible Bridge | Diodes Inc

The Diodes Incorporated PI7C9X111SLBFDE is a SlimLine x1 PCI Express to 32-bit/66 MHz PCI reversible bridge housed in a 128-pin LQFP (14x14 mm) package. According to the Diodes product page, the part delivers high-performance forward and reverse bridging with very low power consumption and a small footprint, making it the latest addition to the PCI Express Bridge SlimLine family of solutions. Key headline specifications include: 32-bit/66 MHz PCI interface, x1 PCIe upstream port, reversible bridge architecture, and 128-LQFP (14x14) footprint. A PCI Express-to-PCI bridge is a specialized interface IC that converts transactions between the modern PCIe serial point-to-point protocol and the legacy parallel PCI bus, enabling legacy PCI cards (NICs, video capture, industrial I/O) to operate behind newer PCIe-only host chipsets. It sits within the broader taxonomy of interface ICs -> bus bridges -> protocol converters -> semiconductors, and is one of the few commercially active reversible bridge families in production. Compared with conventional PCIe-to-PCI bridges, the PI7C9X111SL adds bidirectional traffic support, allowing the legacy PCI device to expose memory or DMA windows to the PCIe host. Key features highlighted on the PI7C9X111SL datasheet include compliance with PCI Express Base Specification 1.1, 32-bit/66 MHz conventional PCI bus support, REQ/L[3:2]/REVRSB pin-strap configuration, and an optional Clock Power Management mode entered via TM1 strap. The bridge supports PME#, INTx, and conventional PCI interrupt/clock request signaling for legacy adapter passthrough. Its small-footprint 128-LQFP makes it attractive for embedded single-board computers and industrial backplanes with tight board real estate. The device uses a packetized split-transaction architecture to translate PCIe TLP packets into conventional PCI cycles, with internal buffering sized for the x1 link. The reversible bridge capability means the chip can also operate as a PCI-to-PCIe bridge (PCI primary side facing the host), which is uncommon and useful in adapter cards that need to expose a single PCIe endpoint while presenting legacy PCI bus timing upstream. Typical uses are industrial drive-in backplanes, retrofit board adapters that need to expose a single PCIe endpoint while presenting legacy PCI bus timing upstream, and embedded SBCs continuing to host legacy add-in cards. The 128-LQFP package supports a common load of 60 trailing-combe CTPs, enabling cost-effective board assembly. When designing with this part, ensure the upstream PCIe link is wired with proper AC coupling capacitors and 100-ohm differential impedance. The TM1 strap selection for Clock Power Management should be tied high or low through a 10k resistor at board level. The bridge requires a 100 MHz reference clock for the PCIe side and a PCI clock for the downstream bus - both must be present before PERST# de-assertion. This page synthesizes distributor pricing, drop-in alternatives from Diodes Incorporated and competitors, and practical design notes not consolidated in the manufacturer datasheet. Compliance status and parametric proximity have been cross-checked against DigiKey, Mouser, Octopart, and the Diodes product page.

Permintaan RFG Kontak
PI7C9X111SLBFDEX - PCIe to PCI Reversible Bridge | Diodes Inc
PI7C9X111SLBFDEX

PI7C9X111SLBFDEX - PCIe to PCI Reversible Bridge | Diodes Inc

The Diodes Incorporated PI7C9X111SLBFDEX is a SlimLine x1 PCI Express to 32-bit/66 MHz PCI reversible bridge IC in a 128-pin LQFP (14x14 mm) package. It delivers high-performance, low-power transparent bridging between a PCIe x1 upstream port and a conventional 32-bit/66 MHz PCI bus, supporting both forward (PCIe-to-PCI) and reverse (PCI-to-PCIe) bridge operation. The part is supplied on Tape & Reel and is rated for industrial temperature operation. A PCIe-to-PCI bridge is a protocol-translating device that lets modern systems lacking a native PCI host controller still address legacy PCI cards, or conversely lets a legacy PCI host expose an endpoint to a PCIe root complex. Bridges like the PI7C9X111SLBFDEX sit in the interconnect hierarchy between the system root complex and the I/O subsystem, allowing product designers to extend the lifecycle of mature 32-bit/66 MHz PCI peripherals (data-acquisition cards, frame grabbers, industrial I/O) on newer PCIe-only CPUs, or to add PCIe endpoint capability to legacy PCI platforms. Key features include 32-bit/66 MHz PCI bus support, a single-lane (x1) PCIe interface, reversible bridge direction, very low power consumption, a small LQFP-128 footprint, and clock power management. The reversible architecture is enabled by pin strapping on the TM1 ball: when TM1 is strapped low, the part uses REQ_L[3:2] and REVRSB to invoke the Clock Power Management feature at PERST# de-assertion. The PI7C9X111SLBFDEX is part of Diodes' SlimLine PCIe bridge family, optimized for compact embedded designs. Typical applications include legacy PCI card migration onto PCIe-only host boards, industrial single-board computers, test and measurement backplanes, embedded vision and frame-grabber adapters, and reverse-bridge use cases where a legacy PCI host must communicate with a PCIe endpoint. The -EX suffix on the part number denotes the Tape & Reel packaging option. When designing with this device, pay close attention to PCIe reference-clock routing and AC-coupling capacitor placement, ensure PERST# timing complies with the PCIe CEM specification, and follow the datasheet's hot-plug and clock-power-management pin-strap recommendations. The part operates from a single 3.3 V supply. This page synthesizes distributor pricing, drop-in alternative analysis, and practical design notes for the PI7C9X111SLBFDEX that are not consolidated in the manufacturer datasheet, helping engineers evaluate sourcing and second-source options.

Permintaan RFG Kontak
PI7C9X112SLFDEX - PCI-to-PCI Bridge | Diodes Incorporated
PI7C9X112SLFDEX

PI7C9X112SLFDEX - PCI-to-PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C9X112SLFDEX is a PCI-to-PCI bridge interface integrated circuit packaged in a 128-pin LQFP measuring 14 mm by 14 mm. It is identified as a PCI Express bridge and is supplied in a tape-and-reel configuration with a standard reel quantity of 1,000 units. The device is intended for systems that must connect conventional PCI bus equipment to a PCI Express host or another modern PCI Express interface. A PCI-to-PCI bridge is a protocol and transaction-layer interface controller that allows legacy PCI devices to operate within a PCI Express system. Within the broader semiconductor hierarchy, this component is a bus controller, interface IC, and PCI Express bridge. Its primary purpose is to translate the signaling and transaction behavior required by a PCI Express link and a conventional PCI bus so that existing PCI cards can communicate with a PCIe-capable host system. The PI7C9X112SLFDEX uses the PI7C9X112SL device family designation and is available from Diodes Incorporated under an extended-order-code configuration. Distributor records identify the target as a specialized PCI interface IC with a maximum listed supply voltage of 1.1 V, gull-wing terminal geometry, a square HLFQFP package, and 128 terminals. The family datasheet also covers the PI7C9X112SL PCI Express Bridge and provides the primary technical reference for system integration. The 128-terminal LQFP package provides a large pin count suitable for the parallel PCI bus, power distribution, clocking, control, configuration, and PCIe interface functions. Because its electrical characteristics are not reproduced in the retrieved distributor summaries, engineers should use the PI7C9X112SL datasheet pin-description table, reference design, and recommended-decoupling guidance when assigning PCB nets and validating signal timing. Typical uses include industrial computers, embedded industrial controllers, test equipment, communication appliances, and legacy PCI expansion systems that need a PCIe-to-PCI bridge. The bridge is particularly useful when an established PCI card or peripheral must be retained while the host platform transitions to PCI Express. PCB implementation requires careful routing of the conventional PCI signals and correct power, reference-clock, configuration, and reset connections. Keep high-speed PCIe traces short and continuous, observe the manufacturer’s reference-plane and decoupling arrangements, and verify all connector-facing signals against the applicable PCI and PCI Express system-design constraints. This product page consolidates package, ordering, interface, and procurement information with practical PCB-planning guidance and a controlled replacement assessment. It also distinguishes a verified same-package ordering alternative from unverified functional equivalents, helping engineers identify where a direct drop-in substitution can be considered and where a complete interface review is mandatory.

Permintaan RFG Kontak
PI7C9X1170ABLEX - I2C/SPI to UART Bridge | Diodes
PI7C9X1170ABLEX

PI7C9X1170ABLEX - I2C/SPI to UART Bridge | Diodes

The Diodes Incorporated PI7C9X1170ABLEX is a single-channel I2C-bus or SPI to UART bridge controller that supports data rates up to 33 Mbps and provides eight programmable general-purpose I/O pins in a 16-pin TSSOP package. It is designed for systems where a serial peripheral interface must be connected to a UART-based host, embedded controller, or data-acquisition equipment. An I2C-to-UART bridge is an interface IC that translates transactions between two serial protocols with different clocking and framing conventions. The PI7C9X1170 belongs to the broader UART interface controller category and combines serial bus conversion with programmable I/O, allowing a compact host interface to connect sensors, flash memory, converters, and other peripheral devices over I2C or SPI. According to the manufacturer datasheet, the controller supports data rates up to 33 Mbps and includes as many as eight additional programmable GPIO pins. These resources let the device collect sideband status signals, control chip-select or reset lines, or monitor external circuit conditions while the main serial channel handles data transfer. The compact TSSOP package also supports cost-sensitive, space-constrained handheld and embedded systems. The PI7C9X1170 is described as guaranteeing low operating and sleeping current, making power management an important part of its architecture. A bridge controller can remain connected to a battery-powered peripheral while providing a defined low-power operating state. Exact supply-voltage limits, quiescent-current figures, and logic thresholds should be confirmed from the electrical-characteristics tables in the manufacturer datasheet before the device is placed in a production design. Typical uses include battery-powered instruments, sensor-hub boards, flash-memory access systems, and embedded instruments that need to translate I2C or SPI transactions into a UART stream. The bridge is particularly useful when an existing UART-capable processor lacks spare I2C or SPI controllers, or when consolidating peripheral access reduces the pin count and software complexity of a baseboard. Confirm the package pin assignments, signal levels, clock configuration, and supported host protocol before layout release. Keep UART and serial-clock traces short, provide the required bypass capacitance at the supply pins, and validate the bridge configuration in firmware before placing it in a timing-critical or high-voltage environment.

Permintaan RFG Kontak
PI7C9X1170ACLEX - I2C/SPI to UART Bridge | Diodes
PI7C9X1170ACLEX

PI7C9X1170ACLEX - I2C/SPI to UART Bridge | Diodes

Diodes Incorporated PI7C9X1170ACLEX is an I2C-bus/SPI-to-UART bridge controller with 64-byte transmit and receive FIFOs, supplied in a 24-pin TSSOP package. It operates from 1.62 V to 3.63 V and supports industrial-temperature applications. The device provides a bridge between serial protocols used by embedded processors and peripheral controllers. An I2C-to-UART bridge is a protocol-conversion interface IC within the broader hierarchy of interface integrated circuits, serial controllers, and semiconductors. Its purpose is to transfer commands or data across incompatible serial interfaces while buffering traffic through dedicated FIFOs. The PI7C9X1170ACLEX combines an I2C controller, an SPI interface, and a UART interface in one package, reducing the need for separate discrete interface components. Key features include 64-byte TX and RX FIFOs, support for Standard-mode and Fast-mode I2C-bus operation, and a 1.62 V to 3.63 V operating-voltage range. These features make the controller useful where a host processor needs a compact, low-voltage serial bridge. The 24-terminal TSSOP package supports surface-mount PCB assembly and is available in a 3000-piece tape-and-reel format. The bridge architecture separates upstream I2C or SPI transactions from UART output through internal buffering. The FIFOs help accommodate short periods of mismatch between host-side request rates and UART data consumption. Exact baud-rate options, electrical timing limits, pin assignments, and supported clock configurations should be confirmed in the manufacturer datasheet before finalizing a high-speed interface design. Typical applications include embedded-system service interfaces, industrial controllers, programmable logic device configuration, memory-programming systems, instrument-control boards, and host-to-peripheral data links. In each case, the controller allows an embedded processor to communicate through UART while using I2C or SPI as the control-side bus. PCB design should preserve short, clean routes between the bridge and its host connector or processor. Keep UART signal routing away from high-speed clock and SPI nets, provide clean ground returns, and verify logic levels against every connected device. The 1.62 V to 3.63 V supply range also makes input- and output-level compatibility a central system-design check. This product page consolidates the device interface, package, voltage, FIFO, and sourcing details with practical replacement and PCB guidance. It supports engineers comparing the PI7C9X1170ACLEX with same-footprint controller options while keeping the selection focused on verified pin and parameter compatibility.

Permintaan RFG Kontak