Produk (42.000+)

PI2USB4122ZHEX - USB 3.2 Gen 1 4:1 Mux/DeMux Switch | Diodes Inc
PI2USB4122ZHEX

PI2USB4122ZHEX - USB 3.2 Gen 1 4:1 Mux/DeMux Switch | Diodes Inc

The Diodes Incorporated PI2USB4122ZHEX is a high-performance USB 3.2 Gen 1 (formerly USB 3.0) 4:1 mux/demux switch IC housed in a 42-TQFN (9x3.5 mm) package with an exposed thermal pad. The device supports four differential channels that can be routed between one USB Type-C/USB 3.0 port and four possible source/sink endpoints, enabling switching of SuperSpeed USB (5 Gbps) signals with minimal insertion loss and return loss across the full USB 3.2 Gen 1 frequency spectrum. A USB switch (also called a USB mux/demux or USB crossbar switch) is a high-speed analog multiplexer designed to route USB 2.0 and SuperSpeed USB signals between multiple physical connectors or controllers while preserving signal integrity. As a category, USB switches sit within the broader hierarchy of analog switches and multiplexers -> signal switches -> interface ICs -> semiconductors. They are essential building blocks in any system that must share limited USB ports among multiple functions (charging, data, audio, debug), and they sit electrically downstream of the USB PHY and upstream of the physical connector. PI2USB4122 is the second-generation Diodes Inc. offering in this category and operates from a single 1.8 V supply rail, simplifying integration into modern low-voltage SoCs. Key differentiating features include 5 Gbps SuperSpeed USB channel support, low 5 ohm typical on-resistance per channel, -3 dB bandwidth exceeding 2.5 GHz to preserve USB 3.2 Gen 1 eye margins, 1.8 V single-supply operation, and integrated sideband/USB 2.0 pass-through routing. The exposed thermal pad on the TQFN package keeps the die-to-ambient thermal resistance low enough for hot-plug events without derating. The PI2USB4122 uses a wide-bandwidth CMOS pass-gate architecture with adaptive biasing to maintain flat frequency response up to 2.5 GHz. Internal ESD protection exceeds 2 kV HBM on the high-speed data lines, reducing external TVS diode count. The control logic accepts standard GPIO inputs for channel selection, allowing direct connection to a USB Type-C port controller without an external I/O expander. Typical applications include USB Type-C port multiplexers in laptops, tablets and docking stations, smartphone fast-charge/data switching paths, USB 3.0 hubs with multiple upstream ports, and Thunderbolt/USB4 sideband routing. The exposed-pad TQFN package makes it suitable for both handheld and dock designs where PCB real estate is constrained. When designing with this part, note the NRND (Not Recommended for New Design) status - the family remains in production for existing platforms but new designs should evaluate the PI3USB4122 or PI3USB31432 successors. Decoupling must include a 0.1 uF X7R cap on VCC placed within 2 mm of the exposed pad, and the high-speed differential pairs require 85 ohm differential impedance with matched trace lengths within the data-sheet tolerance window. This page synthesizes distributor pricing across DigiKey, Mouser, Arrow and LCSC, drop-in alternative candidates from the same Diodes Inc. family, and practical design notes drawn from the manufacturer datasheet - information not aggregated on any single distributor site.

Permintaan RFG Kontak
PI3DBS16213XEAEX - PCIe Gen 4 MUX 12GHz Switch | Diodes Inc
PI3DBS16213XEAEX

PI3DBS16213XEAEX - PCIe Gen 4 MUX 12GHz Switch | Diodes Inc

The Diodes Incorporated PI3DBS16213XEAEX is a 2-channel, 3:1 PCIe Gen 4 multiplexer/switch IC that routes high-speed differential signals between a single common port and three separate downstream paths, delivering up to 12 GHz of -3 dB bandwidth for next-generation server and add-in-card applications. Housed in a 24-pin X1QFN (2x4 mm) exposed-pad package, the device operates from a 3.3 V supply and is rated for the industrial -40 °C to +85 °C temperature range with bidirectional analog switching on each channel. Background Knowledge: A PCIe multiplexer (MUX) is a type of high-speed analog switch that belongs to the broader family of analog switches and multiplexers used in digital interface ICs. PCIe switches sit within the signal-integrity layer between a host CPU/chipset and peripheral endpoints, allowing designers to share a single PCIe lane across multiple downstream devices (such as SSDs, NICs, or riser connectors). They are commonly deployed in storage backplanes, GPU workstations, and server riser cards where lane routing flexibility is required without expanding the host's native PCIe fan-out. Key features of the PI3DBS16213 include 12 GHz bandwidth enabling PCIe Gen 4 (16 GT/s) signaling, two differential channels for 4-lane packet switching capability, low insertion loss for signal-integrity compliance, and bidirectional flow-through pin assignment that simplifies PCB routing on inner stripline layers. The X1QFN-24 (2x4 mm) package exposes a thermal pad that ties to the system ground plane for EMI shielding and thermal dissipation. Architecturally, the device uses a passive FET-based switching matrix with minimal parasitic capacitance, optimizing return-loss and crosstalk figures required for PCIe Gen 4 link-training sequences. Internal bias generation on each channel reduces the BOM by eliminating external DC blocking caps on many reference designs. Typical applications include PCIe Gen 4 server backplanes, NVMe SSD port multipliers on storage enclosures, GPU workstation riser cards, and any design that needs to switch PCIe lanes between two downstream partners without unplugging cables. The 3.3 V single-rail operation is compatible with mainstream server auxiliary rails. Design consideration: maintain a continuous reference (ground) plane under the X1QFN exposed pad to achieve the datasheet's signal-integrity targets; non-continuous flex would degrade return loss at the Nyquist frequency of PCIe Gen 4 (8 GHz fundamental). Source impedance should target 85 Ω differential with skew matched to within 5 ps per channel. This page synthesizes distributor pricing, drop-in-compatible alternatives, application guidance, and engineering design notes not consolidated in the manufacturer brief, giving procurement and design engineers a single decision-ready reference.

Permintaan RFG Kontak
PI3DPX1202A1ZB - DP 1.2 Redriver, 5.4Gbps, 48-TQFN | Diodes Inc
PI3DPX1202A1ZB

PI3DPX1202A1ZB - DP 1.2 Redriver, 5.4Gbps, 48-TQFN | Diodes Inc

The Diodes Incorporated PI3DPX1202A1ZB is a low-power DisplayPort 1.2 redriver with integrated DDC/AUX channel switch, supplied in a 48-pin TQFN (7x7 mm) package. It supports all three DisplayPort 1.2 data rates - 1.62 Gbps (RBR), 2.7 Gbps (HBR) and 5.4 Gbps (HBR2) - and dual-mode DisplayPort (DP++) with TMDS clock frequencies up to 340 MHz, enabling HDMI interoperability through a passive adapter. The device presents a 1-channel high-speed signal path with internal 50 ohm input pull-downs, configurable output level and pre-emphasis, and an Aux Listener that supports link training. What is a DisplayPort redriver? A redriver (also called a signal repeater or retimer-less repeater) is a linear equalizer placed in series with a high-speed serial link. Unlike a retimer it does not add a clock-data-recovery block; instead it compensates for channel loss with adjustable input equalization and output de-emphasis, then re-drives the signal to restore eye-diagram margin. Redrivers sit between a source (GPU, SoC) and a sink (monitor, dongle) and belong to the signal-conditioning family of interface ICs alongside retimers, crosspoint switches and redrivers for USB, PCIe and HDMI. Key features include an ultra-low-power design (136 mA typical at 400 mVpp swing, 0 dB setting), pin-to-pin compatibility with the prior-generation PI3EQXDP1201, dual-mode (DP++/TMDS) input and output, integrated DDC/AUX channel switch, and selectable output level and pre-emphasis through external configuration. The 48-TQFN package combines an exposed thermal pad with a compact 7x7 mm body to fit space-constrained docking stations and embedded DisplayPort designs. The PI3DPX1202A1ZB uses Pericom's (now Diodes) proven linear-redriver architecture, with adaptive or fixed equalization that recovers the high-frequency content attenuated by PCB traces, cable assemblies, and connector transitions. This allows system designers to extend usable cable length, route signals through denser board layouts, or pass strict DisplayPort 1.2 compliance eye-mask tests at the connector. Typical applications include notebook docking stations, DisplayPort 1.2 graphics cards, motherboards with embedded DP outputs, DP-to-HDMI adapters (DP++/TMDS), 4K UltraHD monitors, and Thunderbolt accessory boards. The 5.4 Gbps HBR2 rate supports 4K@60 Hz (3840x2160) color-depth-rich video streams. When designing with this part, place the device as close as practical to the source connector to maximize the recovered signal integrity budget on the far end. Use the AC-coupling capacitors specified in the datasheet, follow the recommended reference-resistor values for the desired output swing, and respect the thermal-pad soldering guidelines for the 48-TQFN package. This page synthesizes distributor stock, same-family Diodes alternatives, and PCB-layout guidance beyond the manufacturer datasheet, with information gain not duplicated on DigiKey or Mouser product pages.

Permintaan RFG Kontak
PI3DPX1202A1ZBE - 5.4Gbps DisplayPort 1.2 Redriver | Diodes Inc
PI3DPX1202A1ZBE

PI3DPX1202A1ZBE - 5.4Gbps DisplayPort 1.2 Redriver | Diodes Inc

The Diodes Incorporated PI3DPX1202A1ZBE is a low-power DisplayPort 1.2 redriver with integrated DDC/AUX channel switch, supplied in a 48-pin TQFN (V-QFN7070-48, 7x7 mm) package with exposed thermal pad. The device supports one channel at up to 5.4 Gbps data rate per lane, making it suitable for DisplayPort 1.2 (HBR2) source-side and sink-side signal conditioning. Per the Diodes datasheet, the PI3DPX1202A1 offers signal buffering/redriver functionality with integrated DDC/AUX multiplexer switching between source and sink. A signal buffer/redriver is a linear or adaptive repeater placed in series with a high-speed serial channel to compensate for channel loss caused by PCB traces, connectors, cables, or inter-symbol interference. It restores signal amplitude and rise/fall times without re-timing the data (a redriver is protocol-transparent), which is critical for DisplayPort, HDMI, USB 3.0, and PCIe Gen2/Gen3 links where budgets may be exceeded by the physical medium. Within the broader component taxonomy, a redriver sits below retimers (which recover clock/data) and above simple repeaters, and it belongs to the Interface ICs > Signal Buffers, Repeaters family of mixed-signal analog conditioning products. Key features include 5.4 Gbps per-lane support (DisplayPort HBR2), adaptive equalization to compensate for frequency-dependent channel loss, transmit de-emphasis to reduce inter-symbol interference at the source, integrated DDC/AUX switch for source/sink routing, low standby current, and 3.3 V single-supply operation. The TQFN-48 (7x7 mm) package with exposed pad provides a low thermal resistance path for surface-mount designs. Internally, the redriver combines a CTLE-style adaptive equalizer at each input with a fixed or selectable de-emphasis driver at each output, plus auxiliary logic for DDC/AUX channel switching. The equalizer extends the usable channel length at HBR2 (5.4 Gbps) where 28 AWG cable losses exceed 10 dB at the Nyquist frequency. The DDC/AUX switch supports bidirectional auxiliary and EDID transactions without an external mux. Typical applications include notebook docking stations, monitor input panels, DisplayPort dongles and adapters, embedded display boards, video capture cards, and any compact DisplayPort source/sink where PCB trace or cable length exceeds the native 8-10 dB loss budget at HBR2 rates. When designing with this part, place it within 4 inches of the DisplayPort connector; provide a solid 3.3 V decoupling network (10 uF bulk + 0.1 uF/0.01 uF high-frequency) at VCC; and route the high-speed TX/RX pairs with 100 ohm differential impedance and length matching within 5 mils per pair. This page synthesizes distributor pricing, drop-in same-package alternatives from the Diodes DisplayPort redriver family, DDC/AUX mux companion parts, and practical PCB layout notes not aggregated in the manufacturer datasheet.

Permintaan RFG Kontak
PI3USB102GZLEX - USB 2.0 2:1 Switch with 5V Protection | Diodes Inc
PI3USB102GZLEX

PI3USB102GZLEX - USB 2.0 2:1 Switch with 5V Protection | Diodes Inc

The Diodes Incorporated PI3USB102GZLEX is a high-performance USB 2.0 high-speed switch configured as a single differential channel 2:1 multiplexer/demultiplexer, packaged in a 10-pin TQFN (1.3x1.6 mm) with an exposed thermal pad. It supports USB 2.0 high-speed (480 Mbps) signaling, offers low on-resistance (5 ohm max), a 1 GHz -3 dB bandwidth, and integrated 5V over-voltage protection on Y+/Y- pins per USB 2.0 specification, allowing all I/O pins to withstand Vbus shorts (5V +/- 10%) whether the chip is powered on or off. A USB switch is a specialized analog multiplexer designed to route USB 2.0 differential pairs between two physical ports or between a single port and a downstream controller. It belongs to the broader family of analog switches and multiplexers, which sit under interface ICs in the semiconductor taxonomy. These parts are critical in systems where one USB physical-layer transceiver must service multiple connectors, OTG roles, USB Type-C role swaps, dock/multi-connector designs, or test-mode path selection. By isolating one data path while activating another, the switch lets one SoC PHY serve two USB connectors without contention. Key differentiating features include very low bit-to-bit skew, high channel-to-channel noise isolation, flow-through pinout for simplified PCB routing, and an improved Ioff voltage range that reduces leakage when VCC is removed. Bidirectional operation means it supports both host-side and device-side roles equally well, and it operates across the -40C to +85C industrial temperature range. The 10-TQFN (1.3x1.6) footprint measures only 2.08 mm^2, enabling it to fit comfortably inside USB connector shields, Type-C mid-mount boards, and dongle-class products. Typical applications for the PI3USB102GZLEX span consumer tablets, notebooks, dock stations, USB Type-C adapters, OTG phones, and any system that needs to share one USB 2.0 PHY between two physical ports. Inside a tablet, for example, it sits between the SoC's USB pins and the system micro-USB or Type-C connector, providing 5V Vbus short protection for the SoC's USB lines. The part can also multiplex between an internal USB header and an externally accessible connector for service-mode diagnostics or docking. When designing with the PI3USB102GZLEX, place the device adjacent to the USB connector so the 5V Vbus short protection works as close to the system boundary as possible. Use a 100 nF decoupling capacitor close to VCC, and follow the USB 2.0 differential pair impedance target of 90 ohm differential. When the chip is powered down, signal leakage through the switch is dominated by Ioff, so confirm this does not exceed downstream PHY leakage budgets. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical PCB design considerations - information that goes beyond what is found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PI3VST01UE - VGA HPD Signal Generator | MSOP-8 | Diodes
PI3VST01UE

PI3VST01UE - VGA HPD Signal Generator | MSOP-8 | Diodes

The Diodes Incorporated (formerly Pericom) PI3VST01UE is a single-channel VGA Hot Plug Detect (HPD) signal generator IC housed in an 8-pin MSOP (Mini Small Outline Package). The device generates a buffered HPD logic signal used in legacy VGA connectors, supporting DisplayPort-to-VGA adapters, docking stations, and monitor-side hot-plug detection circuits where a clean, low-jitter logic-level assertion is required. Key features include a wide 3.0 V to 5.5 V single-rail supply range, CMOS/TTL-compatible HPD output, low quiescent current draw suitable for always-on bias rails, and an integrated pull-up on the HPD output pin per the VESA-recommended 1 kohm impedance. The MSOP-8 surface-mount package is footprint-compatible with standard industry pinouts and supports automated PCB assembly. The PI3VST01UE is a specialized analog mixed-signal interface IC belonging to the analog switch / special-purpose switch family (also classifiable as a video interface switch). Within the broader component taxonomy it sits under interface ICs, video ICs sub-category, semiconductor -> integrated circuit -> analog mixed-signal IC -> HPD signal generator. Its function is to provide electrical buffering and level translation of the HPD logic signal that source devices use to detect cable presence on VGA/DisplayPort output chains. Typical applications include DisplayPort-to-VGA adapters, video docking stations, monitor-side cable-presence detection on VGA inputs, KVM switches that must expose HPD to a graphics source, and legacy graphics cards that lack a native HPD output stage. It is also used in industrial video distribution equipment where hot-plug events must be regenerated cleanly to avoid host GPU re-enumeration glitches. When designing with this device, observe standard ESD precautions on the VGA DDC/HPD lines and decouple VCC with at least a 0.1 uF ceramic capacitor placed within 5 mm of the supply pin. The exposed pad on the MSOP-8 should be soldered to the PCB ground plane for thermal performance and pin-1 reference accuracy. This page synthesizes distributor pricing (DigiKey, Mouser, Octopart), package-level cross-references, drop-in alternatives, and PCB-level design notes into a single reference that is not duplicated on the manufacturer datasheet.

Permintaan RFG Kontak
PI4IOE5V96248ZLEX - 48-bit I2C I/O Expander 56-TQFN | Diodes Inc
PI4IOE5V96248ZLEX

PI4IOE5V96248ZLEX - 48-bit I2C I/O Expander 56-TQFN | Diodes Inc

The Diodes Incorporated PI4IOE5V96248ZLEX is a 48-bit I2C-bus I/O expander organized as 6 banks of 8-bit quasi-bidirectional I/O, packaged in a 56-pin TQFN (7x7 mm) with an exposed thermal pad. It operates from a 2.3 V to 5.5 V supply, supports a 1 MHz I2C (Fast-mode Plus) interface, and provides an open-drain interrupt output plus a hardware reset pin for cascading and address expansion. An I2C I/O expander is a digital IC that multiplies the limited GPIO resources of a host microcontroller by exposing additional general-purpose input/output pins addressable over the two-wire I2C serial bus. In the broader component hierarchy, this places the device within the interface IC category (I/O expanders), itself a subclass of digital logic and bus-interface semiconductors that sit between a controller and peripheral signals. The PI4IOE5V96248 specifically targets MCUs whose GPIO count is the limiting factor for keypads, switches, LEDs and other human-machine interfaces. Key features include built-in LED driver capability with selectable drive strength (25 mA / 30 mA per pin), 250 nA typical standby current, push-pull and open-drain output modes, hardware reset, and cascading capability through user-configurable I2C addresses. The 56-TQFN exposed-pad package provides a low thermal resistance path that sustains continuous high-current LED drive without derating. The device integrates 5 V tolerant I/O on a 2.3 V-5.5 V supply, allowing direct interface to 3.3 V and 5 V rails without level shifters. Internally the chip implements six 8-bit I/O banks (P0..P5), each with independent control registers for direction, pull-up enable, output value, and interrupt-on-change masking. The interrupt output aggregates any unmasked change across the 48 pins and signals the host, while the reset pin simplifies multi-chip synchronization and cascaded configurations. The 1 MHz I2C clock and cascading address expansion make it suitable for very large GPIO fanouts in industrial control panels. Typical applications include industrial keypads and control panels, multi-LED status indicators, white goods human-machine interfaces, point-of-sale terminals, and any MCU-limited system requiring 48 or more general-purpose I/O lines. The integrated LED driver also makes it a strong fit for RGB lighting arrays that otherwise occupy multiple MCU pins with software PWM. When designing with this part, route the 56-TQFN exposed pad to a contiguous ground copper pour for both thermal dissipation and low-impedance return. The I2C pull-ups must be sized for the 1 MHz Fast-mode Plus clock; values in the 1 kOhm to 2.2 kOhm range are typical for 3.3 V and 5 V rails. Multiple PI4IOE5V96248 devices may share the bus by setting their A0/A1/A2 address straps to unique values, expanding the system to 192 I/O or more without any firmware change to the bus protocol layer. This page synthesizes distributor pricing, drop-in alternatives, and practical I2C expander design notes not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
PI5USB31213 - USB Type-C DRP Controller 10Gbps | Diodes Inc.
PI5USB31213

PI5USB31213 - USB Type-C DRP Controller 10Gbps | Diodes Inc.

The Diodes Incorporated PI5USB31213 is a USB Type-C Dual Role Port (DRP) controller with integrated 2:1 USB 3.2 Gen 2 differential mux switches supporting 10Gbps SuperSpeed data rates, housed in a 24-pin X1-QFN (2x4 mm) package. It supports both pin control and I2C control based on the ADDR pin setting. A USB Type-C port controller manages configuration channel (CC) logic, connector orientation detection, and power role negotiation between host, device, and dual-role ports. Within the power management and interface IC hierarchy, DRP controllers bridge the USB Type-C connector and the system USB controller, automatically configuring port roles and flipping SuperSpeed differential pairs for either plug orientation. Key features include compliance with USB Type-C Specification 1.1, dual differential channel 10Gbps mux/deMux switching, automatic port orientation configuration through CC detection, and VCONN sourcing to power active cables and accessories. In host mode the device monitors the ID pin for connector status and offers default current mode to power attached accessories. The PI5USB31213 supports host-mode, device-mode, and dual-role-mode operation selected via the PORT pin, and integrates the USB controller interface and Type-C connector logic in one die, reducing external component count compared to a discrete mux plus separate CC controller. The 5V VCONN sourcing capability eliminates an external VCONN supply for powered cables. Typical applications include smartphones and tablets with USB Type-C connectors, laptops and notebooks requiring dual-role ports, docking stations, and desktop motherboards implementing USB 3.2 Gen 2 front-panel ports where a 10Gbps switchable mux is required. Design considerations: note that the PI5USB31213 is classified NRND (Not Recommended for New Designs) by Diodes Incorporated; new designs should use the actively promoted PI5USB31213A, which shares the same feature set including USB 3.2 Gen 2 10Gbps switching and Type-C 1.1 support. Verify SuperSpeed channel insertion loss budget over the mux at 10Gbps in the layout. This page synthesizes distributor pricing from LCSC, DigiKey, and Mouser, drop-in alternative analysis, and lifecycle guidance not found in the manufacturer datasheet, as of 2026-10-19.

Permintaan RFG Kontak
PI6C557-03AQE - PCIe 2.0 Spread Spectrum Clock Generator | Diodes Inc
PI6C557-03AQE

PI6C557-03AQE - PCIe 2.0 Spread Spectrum Clock Generator | Diodes Inc

The Diodes Incorporated PI6C557-03AQE is a spread-spectrum clock generator compliant with PCI Express 2.0 and Ethernet timing requirements, packaged in a 16-pin QSOP (also referenced as 16-SSOP by some listings). The part accepts a 25 MHz fundamental-mode crystal reference and produces two pairs of differential HCSL outputs at user-selectable frequencies of 25 MHz, 100 MHz, 125 MHz, and 200 MHz. Spread-spectrum modulation is applied through a proprietary PLL architecture to substantially reduce electromagnetic interference (EMI) on the system reference clock. A spread-spectrum clock generator is a timing device that intentionally modulates the output frequency around a center value at a low modulation rate. By spreading the spectral energy of the clock over a wider bandwidth, peak EMI emissions are reduced, helping designs pass regulatory compliance tests such as FCC Class B and CISPR 22. Within the broader clock-and-timing IC category, this part sits in the PCIe clock-generator subcategory alongside PLLs, frequency synthesizers, and zero-delay buffers. Key features include a 25 MHz crystal input, two HCSL (current-mode differential) output pairs, on-chip termination support, output enable / power-down control, and selectable spread-spectrum depth. HCSL is the signaling standard required by PCIe 2.0/3.0 reference clocks and is also used in mainstream Ethernet PHYs. The internal PLL is sourced from Pericom's spread-spectrum technology and maintains low cycle-to-cycle jitter even with active modulation. Typical applications include PCIe add-in cards (network, storage, graphics), embedded systems needing EMI-controlled 100 MHz reference clocks, Ethernet switches and NIC reference rails, and industrial PCs where the part's compliance footprint helps shorten EMI qualification cycles. The device's small 16-QSOP footprint is suitable for compact motherboard layouts. When designing with the PI6C557-03AQE, follow PCIe CEM routing guidelines for the HCSL outputs - 85 ohm differential traces, AC coupling capacitors at the receiver, and length matching within the PCIe spec. The 25 MHz crystal must be fundamental-mode with a load capacitance appropriate for the on-chip oscillator.

Permintaan RFG Kontak
PI6C557-03LEX - 200MHz PCIe Clock Generator | Diodes
PI6C557-03LEX

PI6C557-03LEX - 200MHz PCIe Clock Generator | Diodes

The Diodes Incorporated PI6C557-03LEX is a 200 MHz PCI Express and Ethernet clock generator with two differential HCSL outputs, supplied in a 16-TSSOP package. It accepts a 25 MHz crystal input and uses Pericom PLL techniques to generate selectable 25 MHz, 100 MHz, 125 MHz, and 200 MHz clock frequencies. The verified distributor data identifies a 3.3 V supply, a -40°C to +85°C operating range, and two clock outputs. Its clock-generation and spread-spectrum functions position it within the clock and timing IC category as a phase-locked-loop-based timing device for high-speed digital systems. A clock generator produces reference and data-rate clocks for digital circuits that require stable timing, phase control, and predictable edge placement. In a PCI Express system, a spread-spectrum clock can reduce electromagnetic-interference peaks by distributing clock energy over a frequency band. The PI6C557-03 family is designed for PCI Express and Ethernet clock requirements, making it suitable for computer, embedded, communications, and industrial equipment where a local reference clock is needed. The PI6C557-03LEX provides selectable frequency operation and two differential HCSL output pairs according to the manufacturer datasheet. Its HCSL outputs are intended for high-speed signaling, while configurable spread-spectrum operation helps control radiated and conducted EMI. The manufacturer states that the differential outputs use open-source drivers and require external series and shunt resistors; resistor values and placement should therefore follow the applicable PCI Express layout guidance. The device accepts a 25 MHz crystal input and generates two pairs of differential outputs at 25 MHz, 100 MHz, 125 MHz, or 200 MHz, depending on configuration. This frequency range supports both low-frequency clock distribution and higher-speed PCI Express clocking. The 3.3 V operating supply and 16-TSSOP surface-mount package support compact PCB designs where external clock conditioning and controlled spread-spectrum operation are required. Typical applications include PCI Express endpoint and motherboard clocking, embedded computer platforms, Ethernet interface equipment, communications infrastructure, and industrial control systems. The device is most appropriate when a system needs configurable clock selection, differential outputs, and spread-spectrum EMI reduction rather than a simple low-frequency oscillator or single-ended clock buffer. PCB implementation should preserve short, controlled-length clock traces, provide the required external termination network, and place crystal and decoupling components close to the device. Differential pair routing, return paths, resistor placement, and output configuration must be checked against the manufacturer datasheet and the target PCI Express or Ethernet design guidelines. This page combines verified manufacturer and distributor information with application guidance and replacement analysis.

Permintaan RFG Kontak
PI6CG33A06ZLFEX - 6-Output PCIe 7.0 Clock Generator | Diodes Inc
PI6CG33A06ZLFEX

PI6CG33A06ZLFEX - 6-Output PCIe 7.0 Clock Generator | Diodes Inc

The Diodes Incorporated PI6CG33A06ZLFEX is an ultra-low-jitter, 6-output PCIe 5.0/6.0/7.0 clock generator with integrated on-chip output termination, housed in a 40-pin VQFN (5 mm x 5 mm) package. It accepts a reference input and generates 25 MHz and 100 MHz differential outputs while maintaining sub-30 fs RMS phase jitter that outperforms the 80 fs CK440Q PCIe specification. A clock generator is an integrated circuit that synthesizes one or more precise timing signals from a reference oscillator, providing the heartbeat that synchronizes CPUs, memory, and high-speed serial links. In the broader IC hierarchy it sits below clock buffers and above generic PLLs, and it belongs to the timing-IC family within power management and signal-chain semiconductors. Key features include six differential outputs with individual OE (output enable) pins for granular power management, integrated 85 ohm on-chip termination that eliminates 24 external resistors, 300 ns SMBus 2.0-compatible data hold time, and support for PCIe Gen 1/2/3/4/5/6/7 standards. The on-chip termination simplifies board layout and shrinks BOM count by 24 resistors versus discrete implementations. The device uses Diodes' proprietary PLL architecture with fractional-N feedback to achieve the jitter performance required for PCIe 7.0 while maintaining backward compatibility with PCIe 5.0 and 6.0. Each output pair is independently controllable through SMBus registers, which is essential for modern servers that need to power down unused PCIe lanes to meet energy-efficiency targets. Typical applications include AI server motherboards, NVMe SSD controllers, networking switches, high-performance computing accelerator cards, and CXL-attached memory modules. The compact VQFN-40 5x5 mm footprint also makes the part attractive for space-constrained add-in cards and OCP accelerator designs. When designing with this device, follow the recommended power-rail decoupling layout: 1 uF and 0.1 uF ceramic capacitors placed within 2 mm of each supply pin. Maintain 100 ohm differential impedance on each output pair and route length-match within 5 mils to preserve jitter performance.

Permintaan RFG Kontak
PI6CG33A06ZLFEX-13R - 6-Output PCIe 5.0/6.0/7.0 Clock Generator | Diodes Inc
PI6CG33A06ZLFEX-13R

PI6CG33A06ZLFEX-13R - 6-Output PCIe 5.0/6.0/7.0 Clock Generator | Diodes Inc

The Diodes Incorporated PI6CG33A06ZLFEX-13R is a 6-output ultra-low jitter clock generator designed to meet the demands of the PCI Express 7.0 specification while maintaining backwards compatibility with PCIe 5.0 and 6.0. It delivers 100 MHz HCSL outputs (and 25 MHz reference) from a single reference input, housed in a 40-pin VQFN (5x5 mm) package with integrated on-chip termination that eliminates up to 24 external resistors. Each output features an individual OE (output enable) pin for granular power management, and the device supports SMBus 2.0 programming with 300 ns data hold time for legacy compatibility, plus 0 ns hold time for newer SMBus revisions at 100 kHz and 400 kHz. A clock generator IC is a semiconductor device that takes a low-jitter reference clock (typically from a crystal oscillator or external source) and produces one or more synchronized output clocks, often at multiplied or divided frequencies and with specific output formats (HCSL, LVCMOS, LVDS, LVPECL). PI6CG33A06ZLFEX-13R belongs to the timing generator family, which sits in the broader hierarchy of clock and timing ICs -> clock generators -> PCIe timing components -> power management and system timing for computing and storage platforms. PCIe clock generators are essential building blocks in servers, workstations, NVMe storage, networking switches, and graphics cards where deterministic jitter performance is required by the PCI-SIG specification. Key features include ultra-low additive jitter to meet PCIe 7.0 jitter budgets, integrated 100-ohm differential on-chip termination matching PCIe HCSL impedance directly, six individually-controlled HCSL outputs operating at 100 MHz, and a 25 MHz reference output for downstream devices. The 3.3 V supply simplifies integration with common server and storage platform rails. SMBus programming allows frequency, format, output enable, and spread-spectrum parameters to be configured in-system. From an architectural perspective, the PI6CG33A06 uses a PLL (phase-locked loop) synthesizer to multiply a 25 MHz crystal reference into six phase-aligned 100 MHz HCSL outputs. The on-chip termination eliminates the need for external 100-ohm resistor networks typically required on each HCSL pair, significantly reducing BOM count and PCB complexity while preserving the precise impedance matching required by PCIe 5.0/6.0/7.0 physical-layer compliance testing. Typical applications include PCI Express Gen5/Gen6/Gen7 server riser cards, NVMe storage controller clocking, workstation motherboards, 5G base-station backplane clock distribution, and AI accelerator PCIe retimer cards. The 100 MHz HCSL output format is required by PCIe CEM specification for all downstream add-in cards and baseboard connections. When designing with this device, place 0.1 uF decoupling capacitors as close as possible to each VDD pin and follow the layout recommendations in the manufacturer datasheet. Maintain 100-ohm differential trace impedance on each HCSL pair and minimize stubs to preserve jitter margin. Use the SMBus lines carefully with proper pull-up resistors and keep them away from switching noise sources. This page synthesizes distributor availability and pricing, drop-in PCIe alternatives from Diodes and other vendors, and practical layout notes not found in the bare datasheet, giving engineers a single decision point for PCIe 7.0 clock tree selection.

Permintaan RFG Kontak
PI7C1401AZFEX I2C/SPI Quad Port Expander | Diodes Incorporated
PI7C1401AZFEX

PI7C1401AZFEX I2C/SPI Quad Port Expander | Diodes Incorporated

Diodes Incorporated PI7C1401AZFEX is an I2C-bus/SPI to quad port expander designed for managing common port types such as SFP+ and QSFP+ modules. It provides an I2C-bus or SPI host interface, an interrupt output to the host, and four I2C interfaces for downstream port management. General-purpose pins support low-speed control signaling to connected modules, making the device suitable for networking, telecommunications, and other multi-port systems. The PI7C1401AZFEX operates from a 1.8 V to 3.3 V supply and is packaged in a 56-pin TQFN measuring 11 mm by 5 mm. Its dual-serial-host architecture allows a system controller to reach several peripheral or module ports through one low-speed management link. Rather than assigning a separate controller interface to every port, the PI7C1401 centralizes port-management traffic and reports module or port events through a dedicated host interrupt. Four downstream I2C interfaces are the principal expansion function of the device. These interfaces suit modules that expose management registers, status indicators, or configuration controls through I2C. The upstream SPI or I2C connection supports integration with network processors, field-programmable gate arrays, embedded controllers, and other digital systems. General-purpose control pins add flexibility for slower module-management signals and reduce the need for additional discrete interface components. The PI7C1401 is specifically intended for common networking-port form factors, including SFP+ and QSFP+ equipment. It can be used in optical transceiver cages, switch and router line cards, telecommunications equipment, and industrial control systems that need scalable port management. Its four-port structure is especially useful where a host must monitor or configure multiple pluggable modules while retaining a compact board footprint. Designers should use the manufacturer pin-description table and recommended application schematic when assigning signals. The 1.8 V to 3.3 V supply requirement must be reconciled with the voltage levels used by the host and downstream modules. Decoupling, exposed-pad connection, ground-plane continuity, and signal-routing guidance should follow the manufacturer layout recommendations. Interrupt behavior and the electrical characteristics of the I2C and SPI interfaces should also be checked against the system timing budget. This page organizes the PI7C1401AZFEX function, supply range, package, port-expansion architecture, application fit, and procurement information. It also identifies the technical fields that require confirmation from the manufacturer datasheet, helping engineers evaluate the device without confusing general port-expander functionality with package-specific or timing-specific guarantees.

Permintaan RFG Kontak
PI7C21P100NHE 64-Bit PCI Interface IC | Diodes Incorporated
PI7C21P100NHE

PI7C21P100NHE 64-Bit PCI Interface IC | Diodes Incorporated

Diodes Incorporated PI7C21P100NHE is a 64-bit PCI interface IC used as a PCI-to-PCI bridge, with an operating supply range of 2.3 V to 2.7 V and 3 V to 3.6 V. The device is identified with a 304-CSBGA (31x31) supplier package designation and a 304-BGA package case in the manufacturer-oriented product listing. The PI7C21P100NHE is intended for systems requiring PCI interface bridging and embedded PCI connectivity. A PCI interface IC is a specialized semiconductor that connects PCI buses or peripheral buses and helps translate or coordinate data transactions within a computer system. Within the broader hierarchy, the PI7C21P100NHE belongs to interface ICs, interface controllers, PCI bus controllers, and embedded system semiconductors. Its function is determined by the bridge architecture, signal handling, supported operating conditions, and package implementation. The documented headline characteristics are the 64-bit PCI interface, dual listed supply ranges of 2.3 V to 2.7 V and 3 V to 3.6 V, and the 304-CSBGA (31x31) package designation. These parameters make the part relevant to embedded platforms where a compact, high-pin-count interface solution is required. The exact pin assignments, clocking architecture, performance limits, current consumption, and configuration requirements must be confirmed from the manufacturer datasheet before a board design is released. Typical uses for this device include embedded industrial controllers, PCI-compatible data-acquisition equipment, legacy PCI expansion systems, and customized embedded platforms that require a dedicated PCI bridge. The tight integration of a complex bridge into a BGA package favors multilayer PCB construction and careful high-speed signal-layout practices. Thermal and power planning should account for the device’s actual operating profile under the manufacturer’s stated maximum conditions. The most important design step is to verify the complete pinout and electrical requirements against the manufacturer documentation for the exact ordering code. Package descriptions differ across listings, so the board footprint should be selected from the authoritative mechanical drawing rather than inferred from a marketplace summary. Confirm supply tolerances, decoupling requirements, clock sources, reset behavior, and PCI signal-integrity constraints during schematic review. This page consolidates the product identification, sourcing URLs, technical constraints, and design considerations needed to evaluate the PI7C21P100NHE. It also distinguishes verified attributes from parameters that must be obtained from the official datasheet, helping engineers make a controlled design decision without relying on an unreviewed family-level substitution.

Permintaan RFG Kontak
PI7C7300ANAE - 3-Port PCI Bridge Interface IC | Diodes Incorporated
PI7C7300ANAE

PI7C7300ANAE - 3-Port PCI Bridge Interface IC | Diodes Incorporated

Diodes Incorporated PI7C7300ANAE is a 3-port PCI-to-PCI bridge interface IC packaged in a 272-ball PBGA measuring 27 x 27 mm. The device is intended to bridge PCI-compatible expansion or embedded-system buses, consolidating the physical and logical interface functions needed when one PCI host must communicate with multiple PCI agents. Its defining published features are the three-port bridge configuration, conventional parallel PCI interface, and high-density 272-ball BGA package. A PCI-to-PCI bridge is a specialized interface integrated circuit within the broader PCI interface-controller hierarchy. It sits electrically between two PCI bus segments and allows compatible PCI devices or subsystems on the secondary side to communicate with the host-side PCI bus. Such bridges are especially relevant to embedded computing, industrial control, communications equipment, and legacy PCI expansion systems where a bus translation function is required but a newer host-to-PCI interface is not appropriate. The PI7C7300ANAE provides three PCI ports for designing systems around multiple downstream PCI agents. This makes it useful where a central host must coordinate several bus participants, including endpoint devices, bridges, or controller functions implemented in an embedded subsystem. Because the device uses a large-array BGA package, its implementation depends on multilayer PCB routing, controlled impedance, solid thermal management, and careful high-speed signal routing rather than a simple two-row peripheral package. The 272-ball PBGA is the principal mechanical constraint when evaluating this component. Its 27 x 27 mm footprint provides dense access to the PCI bridge's power, ground, clock, control, and data contacts, but it also demands exact land-pattern compliance, ball-to-pad alignment, and assembly-process validation. Tube packaging is listed in the verified distributor data, so procurement and assembly planning should account for the component's handling requirements before committing to a production build. Typical applications include embedded PCI backplanes, industrial controller platforms, communications gateways, test systems, and specialized expansion chassis that retain conventional PCI connectivity. In these systems, the PI7C7300ANAE serves as the central bus-routing element rather than as a general-purpose processor, memory device, or isolated interface transceiver. Adjacent Ethernet, USB, serial, and industrial interface components may support the wider system, but the bridge remains the component responsible for PCI-to-PCI transaction forwarding. Designers should obtain the manufacturer datasheet and verify all electrical, timing, clocking, power, thermal, and pin-level requirements before schematic capture or PCB layout. The high-density BGA also benefits from assembly-capability review, impedance-controlled stack-up selection, via placement around the device, and adequate power-plane distribution. This page consolidates verified distributor and datasheet-link information, purchasing considerations, application context, and the limits of the currently available substitute data.

Permintaan RFG Kontak
PI7C7300DNAE - 3-Port PCI-to-PCI Bridge | Diodes
PI7C7300DNAE

PI7C7300DNAE - 3-Port PCI-to-PCI Bridge | Diodes

Diodes Incorporated PI7C7300DNAE is a three-port PCI-to-PCI bridge interface IC designed for bridging conventional PCI bus traffic in embedded and industrial systems. It operates from a 3.3 V to 3.6 V supply, is specified at 660 mA, and is housed in a 272-ball PBGA package measuring 27 mm by 27 mm. The PI7C7300DNAE is a surface-mount interface device intended for designs requiring centralized PCI host-bus expansion and translation between PCI transactions and a downstream PCI segment. A PCI-to-PCI bridge is an interface IC that extends a PCI host bus through a transparent bridge while preserving transaction handling across the bus boundary. Within the broader semiconductor hierarchy, it is a specialized bus-interface controller and therefore part of the interface IC category. Its three-port architecture allows multiple PCI resources to be organized behind a shared upstream interface, reducing the need for separate host bridges when system expansion, monitoring, or industrial add-in cards must share a PCI connection. The PI7C7300DNAE operates with a 3.3 V to 3.6 V core supply and is rated for 660 mA. Its three-port configuration is the principal functional feature for systems that must consolidate more than one downstream PCI connection. The 272-PBGA, 27 mm by 27 mm package provides a high pin count for the address, data, control, arbitration, clock, and power interfaces associated with a multiport bridge. Surface-mount construction supports automated assembly but requires careful escape routing and multilayer PCB planning. Technically, the device belongs to the conventional PCI interface generation rather than a compactPCI, PCIe, or USB bridge. Conventional PCI systems separate address and data signaling and use dedicated control, arbitration, interrupt, and clock resources. The three-port topology therefore requires validation at the system level to confirm arbitration behavior, interrupt routing, bus ownership, and the electrical loading introduced by every connected card or module. Typical implementation areas include industrial PCI expansion systems, embedded test equipment, data-acquisition controllers, legacy communication adapters, and PCI carrier systems that need multiple downstream resources. A three-port bridge is especially useful when three downstream bus segments require coordinated operation, but the complete system must remain within the electrical, protocol, and timing limits defined by the manufacturer datasheet. A critical design consideration is the 272-ball BGA layout. The PCB should use the manufacturer land pattern, controlled escape routing, and uninterrupted reference planes for the many high-speed bus signals. Power and ground distribution should be evaluated for the specified 660 mA operating point, with attention given to simultaneous switching activity, connector loading, thermal performance, and the clock and signal-integrity requirements of the target PCI topology. This page organizes the PI7C7300DNAE electrical limits, package information, sourcing questions, functional alternatives, and design considerations into one engineering reference. It also distinguishes true pin-compatible replacements from broader PCI-bridge alternatives, helping designers assess whether a candidate can occupy the same 272-ball footprint or merely provides a similar bus-bridging function.

Permintaan RFG Kontak
PI7C8140AMAE - PCIe-to-PCI Bridge | Diodes Incorporated
PI7C8140AMAE

PI7C8140AMAE - PCIe-to-PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8140AMAE is a dedicated PCIe-to-PCI bridge interface IC with one PCI Express port and one 32-bit/66 MHz PCI port, supplied in a 128-FQFP package measuring 14 x 20 mm. The device supports reversible bridging, allowing the PCIe-to-PCI or PCI-to-PCIe direction to be configured according to system requirements. It is intended for systems that need to connect a legacy parallel PCI subsystem to a serial PCI Express host interface. A PCI-to-PCI bridge is an interface IC that translates transactions between unlike bus architectures. PCI Express uses serial, point-to-point links, while conventional PCI is a parallel, shared bus. The PI7C8140AMAE acts as the protocol and electrical boundary between these two domains, helping system designers retain PCI-compatible expansion equipment while upgrading the primary interconnect to PCIe. The verified product information describes the bridge as a two-port device with a 32-bit/66 MHz PCI interface. The main verified differentiation is reversible operation. Instead of implementing only one fixed bridge direction, the PI7C8140AMAE can be configured for forward or reverse bridging. This flexibility is useful in test equipment, embedded platforms, industrial controllers, and legacy PCI cards that must interoperate with a PCIe host system. The physical implementation uses 128 leads in an FQFP package, providing the pin resources required by the bridge and its associated I/O and power connections. The supplied distributor listings identify the part as a PCI-to-PCI Bridge Interface IC and explicitly describe it as a two-port bridge containing one PCI Express port and one 32-bit/66 MHz PCI port. They also identify a 128-FQFP, 14 x 20 mm package. Detailed operating limits, electrical characteristics, clocking requirements, power rails, signal names, and full pin assignments were not included in the verified dataset and therefore are not inferred here. Those values must be confirmed from the manufacturer datasheet before layout or qualification. In a typical system, the bridge would sit between a PCIe root complex and a legacy PCI bus segment. The downstream PCI devices exchange parallel bus transactions with the bridge, while the bridge serializes those transactions for transmission over PCIe. Reversible configuration can also place the bridge in the opposite direction when the host and target roles require it. Correct clocking, reference-voltage, termination, decoupling, and trace routing remain essential in high-speed implementation. This product page combines the verified distributor and manufacturer-linked data with package, sourcing, comparison, and design guidance that is not available as a single consolidated source. It also distinguishes confirmed facts from values that require the complete datasheet, helping engineers identify what can be used for initial component selection and what still needs verification before PCB release.

Permintaan RFG Kontak
PI7C8148ANJE - 2-Port 32-Bit 66MHz PCI Bridge | Diodes
PI7C8148ANJE

PI7C8148ANJE - 2-Port 32-Bit 66MHz PCI Bridge | Diodes

Diodes Incorporated PI7C8148ANJE is a 2-port PCI-to-PCI bridge interface IC built for 32-bit PCI systems operating at up to 66 MHz. The device is supplied in a 160-LFBGA package measuring 15 x 15 mm, with tray mounting and a 3 V to 3.6 V operating supply range. A PCI bridge is an interface integrated circuit that connects two PCI bus segments and allows devices on one segment to communicate with devices on another. In the PCI hierarchy, the PI7C8148ANJE sits between a host or upstream PCI bus and a downstream PCI segment. Its 32-bit, 66 MHz capability makes it relevant to legacy PCI expansion, embedded system integration, industrial control, and legacy industrial computing platforms where a single bus cannot directly reach all peripherals. The main verified device characteristics are the 2-port PCI-to-PCI architecture, 32-bit PCI data width, 66 MHz operating frequency, 3 V to 3.6 V supply range, and 160-LFBGA (15 x 15 mm) package. These specifications define the electrical and mechanical envelope for the component. The package uses surface-mount LFBGA construction, requiring a PCB land pattern with controlled escape routing and careful via placement beneath the device. The bridge is intended to provide transparent PCI bus segmentation where upstream and downstream agents must share a PCI bus. Using a bridge allows more physical distance between bus loads than a single shared segment may support, while preserving protocol handling within the PCI interface domain. Designers should confirm arbitration, interrupt routing, clocking, and downstream-bus loading against the manufacturer datasheet before finalizing a system. Typical uses include legacy PCI industrial controllers, PCI-to-PCI embedded adapters, test equipment, communication systems, and expansion systems that must retain a 32-bit 66 MHz PCI interface. The 160-LFBGA package is most appropriate for multilayer PCB designs where fine-pitch routing and adequate ground-plane continuity can be implemented. The main design consideration is package complexity. A 160-LFBGA footprint is more demanding than a leaded package for assembly, inspection, and repair, so designers should provide adequate via-in-pad or via fanout options, a continuous reference plane, and process controls for solder bridging. The 3 V to 3.6 V supply requirement also means the bridge must be integrated with a compatible 3.3 V power rail and correctly decoupled at its supply pins. This page consolidates the verified distributor and manufacturer-linked information for PI7C8148ANJE, provides practical packaging and PCB guidance, and distinguishes confirmed parameters from information that must be confirmed in the manufacturer datasheet before production release.

Permintaan RFG Kontak
PI7C8148BNJE - 32-Bit PCI-to-PCI Bridge | Diodes Incorporated
PI7C8148BNJE

PI7C8148BNJE - 32-Bit PCI-to-PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8148BNJE is a PCI-to-PCI bridge interface controller for 32-bit, 66 MHz PCI bus systems, supplied in a 160-LFBGA (15x15 mm) package. It is designed to bridge separate PCI bus segments and operates from a 3.3 V supply, with a stated operating range of 3 V to 3.6 V. The device is categorized as a line and bus controller within the interface IC market, providing a standardized way to connect PCI-compatible devices or subsystems across a PCI-to-PCI link. A PCI bridge is a type of interface controller that connects two PCI bus domains while preserving the electrical and protocol behavior expected by PCI peripherals. The PI7C8148BNJE is intended for embedded systems, industrial equipment, communications platforms, and test systems that require a dedicated bridge rather than a direct connection between PCI devices. Its 32-bit bus width and 66 MHz operating frequency match the PCI bus-generation requirements identified in the verified product data. The principal electrical characteristics available from the verified sources are a 3.3 V operating supply, a 3 V to 3.6 V supply-voltage range, and a 0 °C to 85 °C commercial operating-temperature range. The 160-LFBGA package provides a compact surface-mount implementation for space-constrained board designs. The verified distributor descriptions identify the part as a two-port PCI-to-PCI bridge interface, while the available technical listing identifies it as a 32-bit, 66 MHz PCI bridge chip. Because the product data does not include a complete manufacturer electrical table, detailed specifications such as absolute maximum ratings, quiescent current, propagation delay, PCI signal-level thresholds, and package thermal resistance are recorded as data-needed rather than estimated. The available data also identifies the part as active in one distributor listing and confirms distribution through multiple channels, including DigiKey, Mouser, LCSC, and Octopart. Price and lead-time information should therefore be checked against the current distributor offer for the exact MPN. Typical application considerations include host-adapter boards, embedded PCI expansion systems, industrial control equipment, and PCI-compatible communication or test platforms. The key design issue is ensuring that the bridge, power supply, clocking, and downstream PCI devices comply with the system’s PCI timing, impedance, and power-budget requirements. A compact 160-LFBGA footprint also demands careful PCB layout, thermal analysis, and assembly-process control. This page combines the verified supplier specifications, package and pricing references, cross-reference candidates, and practical engineering considerations to provide a concise purchasing and design reference for the PI7C8148BNJE.

Permintaan RFG Kontak
PI7C8150AMAE - 2-Port 66MHz PCI Bridge | Diodes Incorporated
PI7C8150AMAE

PI7C8150AMAE - 2-Port 66MHz PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150AMAE is a 2-port PCI-to-PCI bridge controller operating at up to 66 MHz and supplied from 3.3 V. The device is packaged in a 208-pin FQFP measuring 28 mm by 28 mm. According to the verified distributor and technical-source data, it is classified as a PCI interface bridge and line or bus controller, making it suitable for systems that need to bridge two PCI bus segments while preserving legacy peripheral compatibility. A PCI bridge is an interface IC that connects two Peripheral Component Interconnect bus segments and manages transaction flow between host and peripheral devices. Within the broader semiconductor hierarchy, this component is a PCI interface IC, a bus controller, and an integrated circuit intended for computer expansion and embedded legacy I/O systems. The PI7C8150AMAE specifically combines a 2-port topology with a 66 MHz maximum PCI clock and a 3.3 V supply requirement. The principal verified characteristics are a 2-port PCI-to-PCI configuration, a 66 MHz maximum operating clock, a 3.3 V supply voltage, and a commercial operating-temperature range of 0°C to 85°C. These specifications make the bridge relevant to PCI industrial controllers, embedded computer platforms, communication equipment, test systems, and industrial adapters that still rely on parallel PCI infrastructure. Its large FQFP footprint provides the physical pin count expected for two independently bridged PCI interfaces. The PI7C8150AMAE is a legacy interface device rather than a general-purpose processor, so its design value depends on maintaining a compatible host bus, connector arrangement, termination network, clocking scheme, and software configuration. A bridge installation must account for the 3.3 V supply requirement, the 0°C to 85°C operating range, and the pin-intensive 208-pin FQFP layout. The verified source snippets do not provide the complete electrical timing tables, maximum current ratings, internal divider values, or the complete pin assignment. Typical deployment uses place the bridge between a primary PCI bus and a secondary PCI segment. Because the component is a two-port bridge, it can support bus-segment connectivity without the external discrete buffering normally required when extending a PCI topology. Integration can reduce board complexity, although the FQFP package requires careful escape routing, ground-plane continuity, and compliant power distribution. The 66 MHz clock limit also defines the performance envelope for attached PCI peripherals. Designers should verify all timing, electrical, reset, clock, and pin-level requirements against the manufacturer datasheet before layout or procurement. In particular, verify PCI specification support, bus-width details, input and output current limits, enable sequencing, peripheral connect/disconnect behavior, and the exact meaning of all 208 pins. Distributor availability and pricing should also be checked because the visible search data does not establish a uniform quantity-price schedule for this exact MPN. This page consolidates verified distributor and manufacturer-source references, separates known specifications from missing technical fields, and identifies a same-family base-frequency alternative for engineers who need a drop-in comparison. The data also records the package, operating conditions, sourcing links, and the technical checks required for a safe PCI-bus integration rather than inferring unverified timing or pin values.

Permintaan RFG Kontak
PI7C8150AND-33 - 2-Port 33MHz PCI Bridge | Diodes
PI7C8150AND-33

PI7C8150AND-33 - 2-Port 33MHz PCI Bridge | Diodes

The Diodes Incorporated PI7C8150AND-33 is a two-port PCI-to-PCI bridge interface IC operating at 33 MHz and packaged in a 256-pin PBGA measuring 17 x 17 mm. The device bridges conventional PCI bus domains, supporting system designs that require a host bus and an additional PCI bus segment to communicate through a dedicated interface controller. A PCI-to-PCI bridge is an interface integrated circuit used to extend and isolate conventional Peripheral Component Interconnect bus segments. It belongs to the PCI interface controller class, the interface IC hierarchy, and the broader semiconductor category. Its primary function is to translate and coordinate bus transactions so that devices on separate PCI segments can communicate while each segment operates as an independent bus. The PI7C8150AND-33 provides two PCI ports, a 33 MHz operating frequency, and a 256-pin PBGA package. Its 17 x 17 mm ball-grid-array construction supports dense board layouts where fine interconnect pitch and many power, ground, and signal connections are required. Current ratings, voltage limits, electrical timing, host interfaces, and supported PCI signaling modes should be confirmed in the manufacturer datasheet before schematic or layout release. This bridge architecture is useful in embedded industrial controllers, legacy PCI expansion systems, test equipment, communication appliances, and embedded computing platforms that still depend on conventional PCI topology. The two-port organization allows a motherboard or mezzanine design to divide devices across multiple bus segments instead of placing every device on one shared PCI bus. The principal engineering trade-off is board complexity. A 256-pin PBGA requires careful escape routing, multilayer construction, ball assignment review, and assembly-process control. Power delivery and return paths must also support the bridge's switching and I/O requirements while minimizing crosstalk on high-fanout bus signals. Use the manufacturer pin-description table to assign every power, ground, clock, reset, interrupt, and PCI data contact. Confirm the complete board stack-up, ball-map orientation, decoupling strategy, and manufacturing rules before release because the public product summary does not provide a complete production pin list. This page organizes the verified device identity, package information, sourcing path, family relationship, and practical integration considerations into a concise engineering reference. It also highlights the distinction between the ordered -33 configuration and related PI7C8150 family members without substituting unverified performance claims.

Permintaan RFG Kontak
PI7C8150ANDE - 66MHz 2-Port PCI Bridge | Diodes Incorporated
PI7C8150ANDE

PI7C8150ANDE - 66MHz 2-Port PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8150ANDE is a specialized PCI-to-PCI bridge interface IC designed for extending or bridging PCI bus systems. The device operates at a maximum clock frequency of 66 MHz, supports two PCI ports, and is supplied in a 256-pin PBGA package measuring 17 x 17 mm. It is intended for legacy PCI expansion, industrial computer, embedded controller, and test-system architectures where an additional PCI-to-PCI interface is required. A PCI bridge is an interface-controller device that connects two PCI bus segments and helps manage transaction translation, arbitration, and the electrical protocol requirements of the Peripheral Component Interconnect bus. In the system hierarchy, the PI7C8150ANDE is a bus controller and interface IC, which belongs to the broader semiconductor and computer-interface ecosystem. The verified product information identifies it as a two-port PCI bridge operating at 66 MHz. The PI7C8150ANDE uses a 3.3 V supply according to the available specification data. The listed maximum supply voltage is 3.6 V, and the reported operating temperature range is 0 to 85 degrees C, or 32 to 185 degrees F. These figures make the component suitable for systems built around conventional 3.3 V PCI interfaces, provided the surrounding equipment remains within the specified environmental range. The 256-PBGA package provides the required dense interconnect arrangement for a high-speed, multi-signal bridge device. Because the available verified results do not provide the complete pin assignment, detailed timing tables, power-consumption values, or electrical characteristics, those parameters should be confirmed against the manufacturer datasheet before final PCB release. The package footprint, signal integrity, power-plane distribution, and PCI connector routing are especially important in a 66 MHz PCI design. Typical uses include PCI industrial motherboards, embedded PCI adapters, legacy workstation peripherals, test equipment, and systems that need a dedicated bridge between PCI host and target buses. The PI7C8150ANDE is best considered a specialized legacy-PCI solution rather than a general-purpose modern PCIe interface. For implementation, engineers should verify the exact PCI electrical requirements, I/O voltage, termination strategy, clock routing, and BGA assembly process against the datasheet. This page summarizes verified distributor and datasheet-search information, identifies the package and interface function, and highlights the data needed for a controlled hardware release.

Permintaan RFG Kontak
PI7C8150BMAE - 66MHz PCI-to-PCI Bridge | Diodes Incorporated
PI7C8150BMAE

PI7C8150BMAE - 66MHz PCI-to-PCI Bridge | Diodes Incorporated

The Diodes Incorporated PI7C8150BMAE is a 32-bit PCI-to-PCI bridge interface IC with two 32-bit PCI ports, asynchronous operation, and support for operation up to 66 MHz. It is packaged in a 208-pin FQFP measuring 28 mm by 28 mm. The device is designed to comply with PCI Local Bus Specification Revision 2.2 and provides a configurable bridge between primary and secondary PCI buses. A PCI-to-PCI bridge is an interface controller that extends a PCI local bus through a transparent transaction bridge. In the product hierarchy, this device is a bus controller, interface IC, and ultimately a semiconductor. The primary and secondary ports each operate at 32-bit width, allowing legacy PCI expansion systems, embedded modules, industrial controllers, and data-acquisition equipment to communicate across separate bus domains while preserving the electrical and transaction behavior expected from PCI Revision 2.2 systems. The verified device family supports asynchronous operation, meaning the primary and secondary interfaces do not require a shared clock. Both ports can run up to 66 MHz, while the PI7C8150B-33 family option is limited to 33 MHz. These characteristics distinguish the bridge from simpler endpoint devices: the PI7C8150BB family translates bus transactions between two PCI segments rather than terminating only one host bus. Its large 208-pin package also provides the substantial I/O and power connections required by two full 32-bit PCI interfaces. Mechanically, the MAE ordering code is associated with the 208-FQFP 28 mm by 28 mm package. The package is substantially larger than a modern low-pin-count interface IC, so its footprint imposes demanding PCB routing and assembly requirements. Exact pin names, exposed-pad connections, voltage tolerances, input thresholds, output timing, current limits, temperature ratings, and package thermal data were not included in the supplied verified records and must therefore be confirmed in the manufacturer datasheet before schematic capture or layout release. Typical applications include PCI-to-PCI expansion systems, embedded industrial control platforms, communications equipment, legacy data-acquisition chassis, and computer expansion products that require an additional bus segment. The asynchronous capability can simplify clock-domain planning when the two PCI segments do not operate in lockstep. However, system designers must still validate bus timing, termination, drive strength, isolation requirements, and power sequencing against the specific board configuration. The main design consideration is PCB complexity. Two full 32-bit PCI buses require careful point-to-point routing for address, data, control, interrupt, and clock signals, together with conservative return-path planning. Layout should minimize stubs, provide continuous reference planes, control crosstalk, and keep bypass connections close to the device. Because the verified data does not supply complete pinout or layout guidance, engineers should use the official Diodes PI7C8150B documentation rather than infer connections from third-party listings. This page consolidates the verified manufacturer description, distributor identification, package information, and product-family behavior into an engineer-oriented reference. It also distinguishes documented capabilities from missing electrical data and explains when a true pin-compatible replacement cannot be confirmed from the available cross-reference records.

Permintaan RFG Kontak
PI7C8150BMAIE - 66MHz PCI Bridge | Diodes Incorporated
PI7C8150BMAIE

PI7C8150BMAIE - 66MHz PCI Bridge | Diodes Incorporated

Diodes Incorporated PI7C8150BMAIE is an asynchronous PCI-to-PCI bridge interface IC with two 32-bit PCI ports, operation up to 66 MHz, a 3 V to 3.6 V supply range, and a 208-FQFP (28x28 mm) package. It is designed for systems that need one PCI bus segment to communicate with another through a transparent asynchronous bridge rather than a conventional host controller. A PCI-to-PCI bridge is an interface IC within the broader PCI interface controller hierarchy. It translates and arbitrates transactions between two PCI Local Bus segments, allowing compatible peripheral cards and bus masters on the secondary segment to access resources through the primary segment. The PI7C8150B family supports asynchronous operation, meaning its primary and secondary buses do not have to operate from one shared clock. The bridge's primary and secondary interfaces are both 32 bits wide, and the standard PI7C8150B supports operation up to 66 MHz. The PI7C8150B-33 family member provides a lower-frequency version rated to 33 MHz. A 3 V to 3.6 V core supply range supports integration into conventional 3.3 V PCI systems while avoiding the need for a 5 V-only interface arrangement. In a PCI system, the bridge can separate bus traffic between processor-side and expansion-card segments. Its asynchronous architecture is useful when the two sides run at different clock rates or when independent bus timing is preferred. The 208-pin FQFP exposes the numerous address, data, control, arbitration, and power pins required by two full 32-bit PCI interfaces. Typical uses include industrial PCI systems, embedded instrumentation, industrial control equipment, data-acquisition systems, and legacy PCI expansion platforms. In each case, the bridge must satisfy the PCI Local Bus electrical and transaction-routing requirements while preserving the intended peripheral ordering and arbitration behavior. PCB design should provide the required 3.3 V supply decoupling and route the many high-speed address and data signals with short, continuous paths. The manufacturer's pin-description table should be used directly when assigning all 208 package connections and when checking board constraints for this large fine-pitch bridge. This page combines manufacturer functionality, package and interface characteristics, drop-in replacement analysis, application guidance, and design cautions to support faster component selection and PCB implementation.

Permintaan RFG Kontak