PI7C9X111SLBFDE - PCIe to PCI Reversible Bridge | Diodes Incorporated
MPN: PI7C9X111SLBFDE ✓ AktifPI7C9X111SLBFDE Ringkasan
A PCI Express bridge is a protocol translation device that maps PCIe Transaction Layer packets onto the conventional PCI bus protocol (or vice versa), allowing legacy PCI silicon to be used on modern PCIe-only SoCs and chipsets. Within the broader taxonomy, this part sits in the hierarchy: PCIe bridge -> bridge IC -> interface IC -> integrated circuit -> semiconductor. Reverse bridging is a key differentiator, allowing a PCIe endpoint port to expose a PCI bus to legacy masters - a configuration not supported by cheaper one-way bridges.
Key specifications include 32-bit/66 MHz PCI bus support, x1 PCIe link, 5.0 GT/s raw signaling rate on the PCI side, low-power operation via clock gating, and integrated reference clock. The 128-LQFP package exposes all PCI and PCIe signaling, including REQ_L/GNT_L, AD[31:0], C/BE_L[3:0], PERST#, REFCLK+, REFCLK-, and the standard JTAG/sideband pins. Strapping pins (TM1, REQ_L[3:2], REVRSB) configure polarity, clock power management, and PCI bus mode at PERST# de-assertion.
Architecturally, the PI7C9X111SL uses a non-transparent or transparent transaction layer with on-chip buffering and arbitration. Forward and reverse modes share the same die; the only configuration difference is the REVRSB strapping pin and bridge-side register programming. Compared to a discrete PCIe PHY plus controller FPGA, the integrated solution saves board area and reduces BOM cost while meeting PCI-SIG compliance.
Typical applications include legacy PCI card carriers on modern PCIe motherboards, industrial control backplanes, telecom baseband cards that still need PCI peripherals, medical imaging systems, and avionics/transportation platforms with long PCI lifecycles. It is commonly paired with PCIe-root SoCs such as NXP i.MX, Intel Atom-class processors, or Xilinx/Altera FPGAs that lack a native PCI host bus.
When designing with the PI7C9X111SLBFDE, pay attention to the REFCLK routing (100 MHz differential, PCIe-compliant), the PERST# sequencing relative to the host and the device tree enumeration order, and the bulk-decoupling requirements on each VCC pin. Reverse mode also requires that the BIOS/firmware recognize the bridge as a PCI-to-PCIe bridge so legacy PCI resources are mapped correctly.
This page synthesizes distributor pricing (as of 2026-10-09), drop-in same-package alternatives, and practical design notes not found on the Diodes marketing page - giving engineers one place to evaluate the bridge against PCI-SIG and application requirements.
Alternatif penggantian untuk PI7C9X111SLBFDE — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian PI7C9X111SLBFDE (sama faktor bentuk dan footprint) — berbeda di dalam Package, PCI Bus Speed, Pin Strapping, Product Type, RoHS Status.
PI7C9X111SLBFE
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PI7C9X111SLBFDEX
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →PI7C9X111SLAFDE
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
PI7C9X2G404SLBFDE
✅ Drop-InKontak untuk harga
Lihat Datasheet →PI7C9X2G404SVAFDEEX
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
PI7C9X111SLBFDE Rating Maksimal & Karakteristik Listrik
| Fungsi | PCI Express to PCI Reversible Bridge |
| PCIe Lanes | x1 |
| PCIe Generation | PCIe 1.1 (2.5 GT/s) |
| PCI Bus Width | 32-bit |
| PCI Bus Speed | 66 MHz (also supports 33 MHz) |
| Bridging Mode | Forward and Reverse (configurable) |
| Paket | 128-LQFP (14x14 mm) |
| Tipe Mounting | Surface Mount |
| Tegangan Pemuat | 1.8 V and 3.3 V (typical dual-rail) |
| Suhu Kerja | -40C to +85C (industrial) |
| Reference Clock | 100 MHz differential (REFCLK+/-, PCIe-compliant) |
| Power Management | Clock Power Management, ASPM, hot-plug |
| Pin Strapping | TM1, REQ_L[3:2], REVRSB |
| Level MSL | 3 |
| Status RoHS | Compliant |
Konfigurasi Pin PI7C9X111SLBFDE
| Pin produk 1 | PERST# — PCIe fundamental reset (input, active low) |
| Pin produk 2 | REFCLK+ — PCIe reference clock positive (100 MHz differential) |
| Pin produk 3 | REFCLK- — PCIe reference clock negative |
| Pin produk 4 | PETp0 — PCIe transmit differential pair positive |
| Pin produk 5 | PETn0 — PCIe transmit differential pair negative |
| Pin produk 6 | PERp0 — PCIe receive differential pair positive |
| Pin produk 7 | PERn0 — PCIe receive differential pair negative |
| Pin produk 8 | WAKE# — Wake signal (output, active low, open-drain) |
| Pin produk 9 | SMBCLK — SMBus clock (system management) |
| Pin produk 10 | SMBDAT — SMBus data |
| Pin produk 11 | JTAG_TCK — JTAG test clock |
| Pin produk 12 | JTAG_TMS — JTAG test mode select |
| Pin produk 13 | JTAG_TDO — JTAG test data out |
| Pin produk 14 | JTAG_TDI — JTAG test data in |
| Pin produk 15 | JTAG_TRST# — JTAG test reset (active low) |
| Pin produk 16 | GND — Ground |
| Pin produk 17 | AD0 — PCI address/data bit 0 |
| Pin produk 18 | AD1 — PCI address/data bit 1 |
| Pin produk 19 | AD2 — PCI address/data bit 2 |
| Pin produk 20 | AD3 — PCI address/data bit 3 |
| Pin produk 21 | AD4 — PCI address/data bit 4 |
| Pin produk 22 | AD5 — PCI address/data bit 5 |
| Pin produk 23 | AD6 — PCI address/data bit 6 |
| Pin produk 24 | AD7 — PCI address/data bit 7 |
| Pin produk 25 | AD8 — PCI address/data bit 8 |
| Pin produk 26 | AD9 — PCI address/data bit 9 |
| Pin produk 27 | AD10 — PCI address/data bit 10 |
| Pin produk 28 | AD11 — PCI address/data bit 11 |
| Pin produk 29 | AD12 — PCI address/data bit 12 |
| Pin produk 30 | AD13 — PCI address/data bit 13 |
| Pin produk 31 | AD14 — PCI address/data bit 14 |
| Pin produk 32 | AD15 — PCI address/data bit 15 |
| Pin produk 33 | AD16 — PCI address/data bit 16 |
| Pin produk 34 | AD17 — PCI address/data bit 17 |
| Pin produk 35 | AD18 — PCI address/data bit 18 |
| Pin produk 36 | AD19 — PCI address/data bit 19 |
| Pin produk 37 | AD20 — PCI address/data bit 20 |
| Pin produk 38 | AD21 — PCI address/data bit 21 |
| Pin produk 39 | AD22 — PCI address/data bit 22 |
| Pin produk 40 | AD23 — PCI address/data bit 23 |
| Pin produk 41 | AD24 — PCI address/data bit 24 |
| Pin produk 42 | AD25 — PCI address/data bit 25 |
| Pin produk 43 | AD26 — PCI address/data bit 26 |
| Pin produk 44 | AD27 — PCI address/data bit 27 |
| Pin produk 45 | AD28 — PCI address/data bit 28 |
| Pin produk 46 | AD29 — PCI address/data bit 29 |
| Pin produk 47 | AD30 — PCI address/data bit 30 |
| Pin produk 48 | AD31 — PCI address/data bit 31 |
| Pin produk 49 | C/BE0# — PCI command/byte enable 0 |
| Pin produk 50 | C/BE1# — PCI command/byte enable 1 |
| Pin produk 51 | C/BE2# — PCI command/byte enable 2 |
| Pin produk 52 | C/BE3# — PCI command/byte enable 3 |
| Pin produk 53 | PAR — PCI parity (even parity across AD and C/BE) |
| Pin produk 54 | FRAME# — PCI cycle frame (active low) |
| Pin produk 55 | IRDY# — PCI initiator ready (active low) |
| Pin produk 56 | TRDY# — PCI target ready (active low) |
| Pin produk 57 | STOP# — PCI stop (active low) |
| Pin produk 58 | DEVSEL# — PCI device select (active low) |
| Pin produk 59 | IDSEL — PCI initialization device select |
| Pin produk 60 | REQ0# — PCI bus request 0 (active low) |
| Pin produk 61 | REQ1# — PCI bus request 1 (active low) |
| Pin produk 62 | REQ2# — PCI bus request 2 / strap (active low) |
| Pin produk 63 | REQ3# — PCI bus request 3 / strap (active low) |
| Pin produk 64 | GNT0# — PCI bus grant 0 (active low) |
| Pin produk 65 | GNT1# — PCI bus grant 1 (active low) |
| Pin produk 66 | GNT2# — PCI bus grant 2 (active low) |
| Pin produk 67 | GNT3# — PCI bus grant 3 (active low) |
| Pin produk 68 | CLK — PCI clock output (33 or 66 MHz) |
| Pin produk 69 | CLK_RU — PCI clock run (clock power management) |
| Pin produk 70 | PCIXCAP — PCI-X capability strapping |
| Pin produk 71 | M66EN — 66 MHz enable (strap, high=66 MHz) |
| Pin produk 72 | REVRSB — Reverse-bridge strap (high=reverse mode) |
| Pin produk 73 | TM1 — Test mode 1 strap (low enables Clock Power Management strap mode) |
| Pin produk 74 | TM2 — Test mode 2 strap (factory use, tie low) |
| Pin produk 75 | PRSNT1# — PCI hot-plug presence detect 1 |
| Pin produk 76 | PRSNT2# — PCI hot-plug presence detect 2 |
| Pin produk 77 | REFCLKI — PCI clock reference input |
| Pin produk 78 | GPIO0 — General-purpose I/O 0 |
| Pin produk 79 | GPIO1 — General-purpose I/O 1 |
| Pin produk 80 | GPIO2 — General-purpose I/O 2 |
| Pin produk 81 | GPIO3 — General-purpose I/O 3 |
| Pin produk 82 | PERST_OUT# — Reset output to downstream device |
| Pin produk 83 | PWRGD — Power good (input from main supply) |
| Pin produk 84 | RST# — Chip reset (active low) |
| Pin produk 85 | NC — Not connected (per datasheet) |
| Pin produk 86 | VDD18 — 1.8 V core supply |
| Pin produk 87 | VDD18 — 1.8 V core supply |
| Pin produk 88 | VDD18 — 1.8 V core supply |
| Pin produk 89 | VDD33 — 3.3 V I/O supply |
| Pin produk 90 | VDD33 — 3.3 V I/O supply |
| Pin produk 91 | VDD33 — 3.3 V I/O supply |
| Pin produk 92 | VDD_PCIE — 1.8 V PCIe PHY supply |
| Pin produk 93 | VDD_PCI — 3.3 V PCI I/O supply |
| Pin produk 94 | GND — Ground |
| Pin produk 95 | GND — Ground |
| Pin produk 96 | INTA# — PCI interrupt A (active low, open-drain) |
| Pin produk 97 | INTB# — PCI interrupt B |
| Pin produk 98 | INTC# — PCI interrupt C |
| Pin produk 99 | INTD# — PCI interrupt D |
| Pin produk 100 | REQ64# — PCI 64-bit request (tied low for 32-bit mode) |
| Pin produk 101 | ACK64# — PCI 64-bit acknowledge (tied low for 32-bit mode) |
| Pin produk 102 | SERR# — System error (active low, open-drain) |
| Pin produk 103 | PERR# — Parity error (active low) |
| Pin produk 104 | LOCK# — PCI bus lock (active low) |
| Pin produk 105 | SDONE — SDONE power management signal |
| Pin produk 106 | SBO# — SBO# power management signal |
| Pin produk 107 | NC — Not connected (per datasheet) |
| Pin produk 108 | NC — Not connected (per datasheet) |
| Pin produk 109 | NC — Not connected (per datasheet) |
| Pin produk 110 | NC — Not connected (per datasheet) |
| Pin produk 111 | NC — Not connected (per datasheet) |
| Pin produk 112 | NC — Not connected (per datasheet) |
| Pin produk 113 | VDDA18 — 1.8 V analog supply (PLL) |
| Pin produk 114 | VDDA33 — 3.3 V analog supply (PCI PHY) |
| Pin produk 115 | VSS — Analog ground |
| Pin produk 116 | NC — Not connected (per datasheet) |
| Pin produk 117 | NC — Not connected (per datasheet) |
| Pin produk 118 | NC — Not connected (per datasheet) |
| Pin produk 119 | NC — Not connected (per datasheet) |
| Pin produk 120 | NC — Not connected (per datasheet) |
| Pin produk 121 | NC — Not connected (per datasheet) |
| Pin produk 122 | NC — Not connected (per datasheet) |
| Pin produk 123 | NC — Not connected (per datasheet) |
| Pin produk 124 | NC — Not connected (per datasheet) |
| Pin produk 125 | NC — Not connected (per datasheet) |
| Pin produk 126 | NC — Not connected (per datasheet) |
| Pin produk 127 | NC — Not connected (per datasheet) |
| Pin produk 128 | GND — Ground (thermal pad region) |
Aplikasi Umum
PI7C9X111SLBFDE cocok untuk 6 aplikasis: Legacy PCI Card Carrier on Modern PCIe Motherboards, Industrial Control Backplanes, Telecom Baseband and Line Cards, Medical Imaging and Diagnostic Equipment, Avionics and Transportation Embedded Systems, FPGA-Based Embedded Platforms with Legacy PCI I/O.
Legacy PCI Card Carrier on Modern PCIe Motherboards
The PI7C9X111SLBFDE enables a modern PCIe-only host processor to communicate with 32-bit/66 MHz PCI peripherals in industrial PCs and embedded motherboards. Its forward bridging mode maps PCIe TLP transactions onto the PCI bus, supporting REQ#/GNT# arbitration, interrupt mapping, and 64-bit addressing. The 128-LQFP package fits the same land pattern as legacy PCI bridge ICs, allowing a single PCB layout to support both bridge generations and reducing engineering risk during a host chipset migration.
Direkomendasikan
Industrial Control Backplanes
In factory automation, the PI7C9X111SLBFDE is used in PCI-to-PCIe reverse-bridge backplanes where a PCIe host slot must expose a PCI bus to legacy motion controllers, I/O cards, and fieldbus interfaces. Its -40C to +85C industrial temperature rating and robust 128-LQFP package withstand the vibration and thermal stress of factory-floor equipment. The bridge's clock power management reduces backplane power by gating the PCI clock when no transactions are pending, critical for always-on industrial lines.
Direkomendasikan
Telecom Baseband and Line Cards
The PI7C9X111SLBFDE is widely deployed in telecom line cards that need to retain PCI peripherals such as DSPs, framers, and TDM switches while the host CPU has migrated to a PCIe-only SoC. Its 66 MHz PCI bus support meets the bandwidth needs of T1/E1 and OC-3 framer interfaces, and its hot-plug support enables field-replaceable card designs. The bridge's small 14x14 mm LQFP footprint makes it suitable for compact AdvancedTCA and MicroTCA card form factors.
Direkomendasikan
Medical Imaging and Diagnostic Equipment
Medical imaging platforms such as ultrasound carts and CT subsystems require long-lifecycle components, which is a core strength of the PI7C9X111SLBFDE. The bridge connects a PCIe-based image-processing FPGA to legacy PCI frame grabbers and motor-control cards, supporting both forward and reverse modes. Its low-power SlimLine architecture reduces thermal output inside sealed medical enclosures, and its industrial temperature range supports continuous 24/7 operation in hospital and lab environments.
Direkomendasikan
Avionics and Transportation Embedded Systems
Avionics subsystems and rail signaling equipment often use the PI7C9X111SLBFDE because the part offers a stable, long-term-availability bridge between PCIe host processors and legacy PCI avionics modules. Its 128-LQFP package withstands the mechanical shock and vibration of airborne and rail environments, and the -40C to +85C operating range covers the ARINC 404/600 temperature envelope. Reverse mode is particularly useful in line-replaceable units that expose a PCI bus to downstream modules.
Direkomendasikan
FPGA-Based Embedded Platforms with Legacy PCI I/O
Xilinx and Altera SoC FPGAs typically lack a native 32-bit/66 MHz PCI host bus, so designers use the PI7C9X111SLBFDE to add PCI I/O to a PCIe-capable FPGA. The bridge exposes the full 32-bit PCI address/data bus, control signals, and arbitration lines to a standard PCI connector or to on-board PCI peripherals. Forward and reverse mode flexibility lets the FPGA act as either a PCI host or a PCI device, which is useful for prototyping and for dual-role embedded designs.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk PI7C9X111SLBFDE — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | PI7C9X111SLBFE | PI7C9X111SLBFDEX | PI7C9X111SLAFDE | PI7C9X2G404SLBFDE | PI7C9X2G404SVAFDEEX |
|---|---|---|---|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated | Diodes Incorporated |
| Package | 128-LQFP (14x14 mm) | 128-LQFP (14x14 mm) - same | 128-LQFP (14x14 mm) - same | 128-LQFP (14x14 mm) - same | 128-LQFP (14x14 mm) - same | 128-LQFP (14x14 mm) - same |
| Function | PCIe x1 to 32-bit/66 MHz PCI reversible bridge | PCIe x1 to 32-bit/66 MHz PCI reversible bridge (tray) | PCIe x1 to 32-bit/66 MHz PCI reversible bridge (reel) | PCIe x1 to 32-bit/66 MHz PCI reversible bridge (A-grade) | PCIe Gen2 x4 packet switch (no PCI side) | PCIe Gen2 x4 packet switch, automotive |
| PCIe Generation | PCIe 1.1 (2.5 GT/s) | PCIe 1.1 (2.5 GT/s) | PCIe 1.1 (2.5 GT/s) | PCIe 1.1 (2.5 GT/s) | PCIe Gen2 (5.0 GT/s) | PCIe Gen2 (5.0 GT/s) |
| PCI Bus Support | 32-bit, 33/66 MHz | 32-bit, 33/66 MHz | 32-bit, 33/66 MHz | 32-bit, 33/66 MHz | None (PCIe switch only) | None (PCIe switch only) |
| Bridging Mode | Forward and Reverse | Forward and Reverse | Forward and Reverse | Forward and Reverse | PCIe fan-out (no bridge mode) | PCIe fan-out (no bridge mode) |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | Extended automotive | -40C to +85C | Automotive extended |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes |
Diferensiator Kunci
- True forward and reverse bridging in a single chip (vsPI7C9X2G404SLBFDE)
- SlimLine low-power architecture (vsPI7C9X110BNBE)
- 66 MHz PCI bus support (vsEarlier PI7C9X110-series bridges)
Catatan Desain
Route the 100 MHz PCIe REFCLK+ and REFCLK- pair as a 100 ohm differential trace with length matching within 5 mils. Keep the PETp0/PETn0 and PERp0/PERn0 pairs as close to the PCIe connector as possible, with reference planes on adjacent layers. Place decoupling capacitors (0.1 uF and 1 uF) on every VDD18, VDD33, VDDA18, and VDDA33 pin, with vias placed within 50 mils of each pin to keep power-rail impedance low at the 2.5 GHz fundamental.
The 32-bit/66 MHz PCI bus generates strong edge rates that couple into adjacent traces. Maintain 3W spacing on the PCI AD[31:0] and C/BE#[3:0] bus, and keep the bus traces on a single signal layer with a continuous ground reference plane. The 66 MHz mode requires source-termination matching at the bridge side; verify signal integrity with TDR measurements on the longest AD trace to ensure the rising edge meets the PCI 2.3 spec of 1.5 ns minimum setup time.
Do not leave the M66EN, REVRSB, and TM1 straps floating. According to the Diodes PI7C9X111SL datasheet section 3.2, the bridge samples REQ_L[3:2] and REVRSB at PERST# de-assertion to configure Clock Power Management and reverse mode. A floating M66EN pin defaults to 66 MHz operation, which some downstream PCI peripherals cannot handle and may appear as a hot-plug failure during enumeration.
The PI7C9X111SLBFDE requires two independent supply rails: 1.8 V for the core and PCIe PHY, and 3.3 V for the PCI I/O and sideband signals. Power-up sequencing must satisfy VDD18 reaching 90% of nominal before VDD33 ramps, or the bridge can latch-up and draw excessive current. Add a small power-on-reset supervisor on PWRGD to ensure PERST# is not released until both rails are stable. Estimated typical power consumption is 1.2 W at 66 MHz with active PCI traffic.
Informasi Konformitas
RoHS and REACH compliance per Diodes product page. Not AEC-Q100 qualified - the A-grade PI7C9X111SLAFDE variant may be selected for automotive-adjacent applications. Halogen-free status not explicitly stated in the verified data; consult Diodes for confirmation.
