Produk (22.000+)

ATTINY25-20MU - 20MHz AVR MCU | Microchip Technology
ATTINY25-20MU

ATTINY25-20MU - 20MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY25-20MU is a picoPower AVR RISC-based CMOS 8-bit microcontroller operating at up to 20MHz, with 2KB ISP Flash memory, 128B EEPROM, 128B SRAM, and six general-purpose I/O lines in a 20-pin QFN exposed-pad package measuring 4 x 4 mm. It also includes one 8-bit timer/counter with compare modes and USI ADC functionality. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one compact device. The ATtiny25 belongs to the TinyAVR family, one branch of the 8-bit AVR RISC architecture within the broader category of embedded processors and microcontrollers. Its small memory footprint and limited I/O count are suited to compact control tasks rather than high-end embedded processing. The ATTINY25-20MU combines 2KB of in-system-programmable Flash with 128B EEPROM and 128B SRAM. Its AVR processing core provides 32 general-purpose working registers, reducing the need to load frequently used values from memory. Six general-purpose I/O lines support digital control and communication functions, while the 8-bit timer/counter with compare modes assists with timing, pulse measurement, and simple waveform-generation tasks. The device uses the Microchip picoPower architecture and supports operation from a 3.3V or 5V supply context. The -20 suffix identifies the 20MHz speed grade, while the MU ordering code identifies the 20-pin QFN exposed-pad industrial-temperature package configuration. Its compact 4 x 4mm footprint supports space-constrained boards, although the exposed pad must be connected according to the manufacturer's layout guidance. Typical uses include compact sensor nodes, simple motor or actuator controllers, low-cost dimmers, miniature instrumentation, embedded timers, and general-purpose hobby electronics. The USI and ADC resources make the device useful for designs that combine digital control with limited analog input or serial-interface requirements. Its 2KB Flash capacity favors compact firmware with focused control logic. PCB design should preserve the pin and exposed-pad requirements of the QFN package, provide short power and ground connections, and follow the manufacturer's decoupling and programming recommendations. Because the device offers only 2KB of Flash and 128B SRAM, firmware should be checked for code size and stack demand before production, while unused GPIO pins require deliberate termination. This product page combines the manufacturer's ATtiny25 architecture details with package-specific information, application guidance, procurement questions, and design considerations. It also distinguishes exact ordering options from broader family members so engineers can assess the ATTINY25-20MU for compact, low-power embedded control designs.

Permintaan RFG Kontak
ATTINY25-20PU - 8-Bit 20MHz AVR Microcontroller | Microchip
ATTINY25-20PU

ATTINY25-20PU - 8-Bit 20MHz AVR Microcontroller | Microchip

The Microchip Technology ATTINY25-20PU is an 8-bit AVR RISC-based CMOS microcontroller with a 20 MHz maximum clock, 2 KB of in-system programmable Flash memory, 128 bytes of SRAM, and 128 bytes of EEPROM in an 8-pin PDIP package. It provides six general-purpose I/O lines and is based on the compact ATtiny25 architecture. An 8-bit microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one device. The ATtiny25 belongs to the hierarchy of 8-bit AVR microcontrollers, embedded microcontrollers, and general-purpose semiconductor control devices. Its small memory capacity and limited I/O make it appropriate for compact control tasks rather than high-bandwidth processing or large application firmware. Key features include 2 KB of ISP Flash, 128 bytes of EEPROM, 128 bytes of SRAM, 32 general-purpose working registers, six general-purpose I/O lines, and a 20 MHz operating speed. The in-system programming interface supports programming and configuration without removing the device from its circuit, while EEPROM provides nonvolatile storage for settings and calibration information. The device uses Microchip's picoPower AVR architecture and combines a reduced instruction set with dedicated timer and counter functions. According to the manufacturer product page, it includes one 8-bit timer/counter with compare modes and a two-wire serial interface. These resources allow the ATTINY25-20PU to handle compact embedded-control functions such as timing, state sequencing, actuator control, and low-volume data acquisition. Typical applications include small sensor nodes, simple motor or actuator controllers, LED lighting modules, household appliance controls, and compact industrial interface boards. Its six I/O lines are useful when the design requires a modest number of digital signals and the firmware does not require substantial storage. The DIP package also facilitates prototyping, educational work, and through-hole assembly. When designing around the ATTINY25-20PU, reserve every I/O pin for its assigned function and check the required peripheral multiplexing carefully. Provide a stable supply and suitable decoupling close to the device, and use ISP programming access that remains electrically safe in both development and production hardware. This page combines manufacturer specifications, package and programming guidance, application fit, and drop-in replacement assessment. It is designed to help engineers compare memory capacity, clock speed, pin compatibility, and implementation trade-offs before committing the ATtiny25 footprint to a PCB.

Permintaan RFG Kontak
ATTINY26-16MU - 16MHz 8-Bit AVR MCU | Microchip Technology
ATTINY26-16MU

ATTINY26-16MU - 16MHz 8-Bit AVR MCU | Microchip Technology

The Microchip Technology ATTINY26-16MU is an 8-bit AVR RISC microcontroller with a 16 MHz clock, 2 KB of Flash program memory, and a 32-pin VQFN package measuring 5 mm by 5 mm. The device also includes 128 bytes of EEPROM and 128 bytes of internal SRAM, making it suitable for compact embedded control, sensing, and low-power automation products. Its industrial-temperature ordering code is -16MU, and the -MUR option denotes a reel-packed production variant. A microcontroller is a programmable control component that integrates a processor core, nonvolatile memory, working memory, and peripherals such as timers and analog converters on one integrated circuit. The ATTINY26 belongs to the AVR family of 8-bit RISC controllers, a category positioned between simple logic controllers and higher-performance 32-bit microcontrollers. Its compact footprint and low component count help reduce board area, assembly cost, and overall system complexity. The ATTINY26-16MU provides 2 KB of Flash memory organized as 1K by 16 bits, 128 bytes of EEPROM for retained configuration, and 128 bytes of SRAM for working variables. According to the Microchip ATtiny26 Summary Datasheet (1477S), the device includes one 8/16-bit timer/counter with prescaler and one 8/10-bit high-speed timer/counter with PWM support. The Mouser product record also identifies an integrated ADC, expanding the range of analog measurements that can be handled without an external converter. At 16 MHz, the AVR core executes a compact instruction set suited to event-driven control loops, pulse generation, signal counting, and small protocol stacks. Its 8-bit architecture simplifies timer arithmetic and register access, while flash-based firmware allows field updates through the AVR programming interface. The internal EEPROM gives designers a place to store calibration values, serial numbers, or configuration data without adding an external memory component. Typical uses include motor-speed control, LED lighting, sensor-conditioning nodes, small appliance controls, and industrial automation modules. The 32-VQFN package is especially useful in space-constrained products where a 20-pin SOIC would be too large. Because the exposed-pad package requires careful layout, designers should follow the manufacturer land-pattern and thermal-via guidance rather than treating it as a leaded package. When designing the PCB, reserve the programming interface, verify the ADC input voltage limits, and confirm that the operating supply matches the device specification. Place input and decoupling capacitors close to their associated pins, and provide adequate thermal copper under the exposed pad. Firmware should include watchdog, brownout, and unused-port handling appropriate to the end product. This page combines the official device characteristics, package details, and programming guidance with a drop-in comparison, application analysis, and practical layout notes. It is intended to help engineers evaluate the ATTINY26-16MU quickly while still requiring verification against the complete manufacturer documentation before a production release.

Permintaan RFG Kontak
ATTINY261A-MF - 20MHz 8-Bit AVR MCU | Microchip Technology
ATTINY261A-MF

ATTINY261A-MF - 20MHz 8-Bit AVR MCU | Microchip Technology

The Microchip Technology ATTINY261A-MF is a high-performance 8-bit AVR RISC-based microcontroller with a 20 MHz maximum clock, 2 KB of Flash memory, 128 bytes of EEPROM, and 128 bytes of SRAM in a 32-QFN 5 x 5 mm package. It provides 16 general-purpose I/O lines and 32 general-purpose working registers for compact embedded control designs. A microcontroller is an integrated semiconductor device containing a processor core, program memory, data memory, and peripherals on one package. The ATTINY261A belongs to the tinyAVR family, a low-power segment of the AVR 8-bit RISC architecture. Its picoPower design is intended for small, cost-sensitive systems that need deterministic digital control without adopting a larger general-purpose processor. Key device resources include 2 KB of in-system programmable Flash, 128 bytes of EEPROM, 128 bytes of SRAM, 16 I/O lines, and 32 working registers. The device operates at up to 20 MHz and includes an 8-bit timer/counter with compare modes according to the Microchip ATtiny261A product description. Its 32-QFN package supports compact surface-mount layouts while retaining access to 16 I/O pins. The 2 KB Flash footprint is suitable for compact firmware containing initialization code, a state machine, periodic control routines, and communication or sensing logic. EEPROM provides 128 bytes of nonvolatile data storage for calibration values, counters, configuration data, or serial numbers. The 128-byte SRAM supports stack space, variables, and working state, so designers should keep RAM allocation and call depth within that limited budget. Typical uses include compact motor controllers, sensor nodes, small control panels, dimmable lighting modules, and embedded accessories where an 8-bit processor, limited I/O, and low component count are valuable. The QFN package also makes the device appropriate for space-constrained consumer and industrial modules when board area, assembly capability, and thermal performance are carefully considered. For PCB design, follow the manufacturer’s QFN land pattern and pin-assignment table, place decoupling capacitors close to the supply pins, and keep programming and clock-routing areas free of noisy switching nodes. Programming should use the supported AVR ISP workflow, and unused I/O pins should be configured appropriately rather than left floating. This page combines manufacturer device information, package and memory characteristics, application guidance, cross-reference findings, and practical design considerations. It also identifies when the original ATtiny261 or related tinyAVR family parts can support a migration without treating functionally related devices as automatic replacements.

Permintaan RFG Kontak
ATTINY261A-MN - 20MHz AVR Microcontroller | Microchip
ATTINY261A-MN

ATTINY261A-MN - 20MHz AVR Microcontroller | Microchip

The Microchip Technology ATTINY261A-MN is a picoPower 8-bit AVR RISC-based microcontroller with a 20 MHz maximum clock, 2 KB of in-system programmable Flash, 128 B of EEPROM, 128 B of SRAM, and 16 general-purpose I/O lines. The device is supplied in a 32-VQFN surface-mount package measuring 5 mm by 5 mm, making it suitable for compact embedded control designs. What is an 8-bit AVR microcontroller? It is a compact RISC-based embedded controller that executes instructions from embedded Flash memory and uses general-purpose registers, timers, interrupts, and serial or analog peripherals to control electronic products. Within the embedded-product hierarchy, the ATTINY261A belongs to the AVR family, the 8-bit microcontroller class, and the broader power-management and embedded-control semiconductor category. Its picoPower implementation emphasizes efficient operation in small control systems. Key device features include 2 KB of Flash organized as 1 K by 16 bits, 128 B of EEPROM, 128 B of internal SRAM, 32 working registers, and 16 general-purpose I/O lines. Peripherals described for this family include an 8-bit timer/counter with compare modes, PWM support, a prescaler, and a high-speed 8/10-bit timer/counter. The operating supply range is 1.8 V to 5.5 V, allowing operation across low-voltage and conventional 5 V embedded systems. The ATTINY261A architecture combines an 8-bit AVR instruction set with Harvard-style separate program and data-memory organization and a reduced instruction cycle time. The 20 MHz operating capability provides practical headroom for event timing, digital control, and low-cost communication peripherals. Compared with larger AVR devices, its 2 KB Flash capacity favors compact firmware rather than graphical interfaces, large protocol stacks, or extensive data logging. Typical uses include motor and valve control, lighting systems, small appliance controllers, industrial interface modules, and compact sensor nodes. Its 16 I/O lines, PWM-capable timers, and flexible 1.8 V to 5.5 V supply range make it useful when a board must combine control outputs with low-voltage sensing. Firmware and peripheral configuration should be selected with the 2 KB program-memory constraint in mind. PCB planning must account for the 5 mm by 5 mm VQFN footprint, exposed thermal-pad requirements, and manufacturer land-pattern guidance. Place decoupling capacitors close to the supply pins and reserve adequate ground-plane area beneath the device to support both electrical return paths and thermal performance. Confirm final pad dimensions against the current manufacturer package drawing before fabrication. This product page combines the manufacturer product information, package and memory details, drop-in family comparisons, and implementation guidance for engineers evaluating the ATTINY261A-MN in compact embedded systems.

Permintaan RFG Kontak
ATTINY261A-MU - 20MHz 8-Bit AVR MCU | Microchip Technology
ATTINY261A-MU

ATTINY261A-MU - 20MHz 8-Bit AVR MCU | Microchip Technology

Microchip Technology ATTINY261A-MU is an 8-bit AVR RISC-based microcontroller operating up to 20 MHz, with 2 KB of Flash memory, 128 B of EEPROM, 128 B of SRAM, and 16 general-purpose I/O lines. The device is housed in a 32-pin VQFN (5x5 mm) package and is designed for compact embedded-control, sensor, communication, and power-control systems. An 8-bit AVR microcontroller is a compact embedded-processing device that combines a RISC-based CPU core, program Flash, data EEPROM, SRAM, general-purpose I/O, and dedicated peripherals in one integrated circuit. The ATtiny261A belongs to the TinyAVR hierarchy within the AVR microcontroller family, providing inexpensive, low-power control for applications that do not require a high-performance 32-bit processor. Its picoPower implementation is intended to balance processing capability with energy efficiency. Key device resources include 32 general-purpose working registers, 16 general-purpose I/O lines, and an 8-bit timer/counter with compare modes. The 2 KB Flash memory provides 1K x 16 words for program storage, while 128 B of EEPROM supports nonvolatile parameter retention. The 128 B of SRAM handles working data and stack operations, and the 16 I/O pins allow direct connection to sensors, switches, indicators, and actuator-control circuitry. The ATTINY261A-MU uses Microchip’s enhanced AVR architecture and is supported by the ATtiny261A family documentation. Its operating voltage spans 1.8 V to 5.5 V, making it suitable for both low-voltage portable systems and conventional 5 V embedded equipment. The 20 MHz maximum clock rate provides ample timing margin for pulse measurement, control-loop updates, serial-data handling, and user-interface polling. Typical uses include building automation, industrial sensing, battery-powered instrumentation, compact motor controllers, LED status indicators, and small control panels. In each case, the device can consolidate several discrete functions: reading a sensor, debouncing inputs, sequencing outputs, storing configuration in EEPROM, and controlling a power stage through timer-based or software PWM functions. PCB design should account for the 32-pin VQFN land pattern, exposed-pad requirements, and the short connection requirements of high-speed clock and power nets. Follow the family datasheet’s recommended decoupling and exposed-pad land pattern, and confirm the exact pin assignments before assigning PCB signals. The 5x5 mm footprint supports compact designs but requires careful assembly planning and thermal via placement. This page organizes the ATTINY261A-MU’s memory, timing, package, and purchasing information with application guidance, verified drop-in options, and design notes. It helps engineers evaluate whether the controller’s 20 MHz performance and 2 KB program-memory limit fit a control task before committing to a PCB layout.

Permintaan RFG Kontak
ATTINY261A-PU - 8-Bit 20MHz AVR Microcontroller | Microchip
ATTINY261A-PU

ATTINY261A-PU - 8-Bit 20MHz AVR Microcontroller | Microchip

The Microchip Technology ATTINY261A-PU is an 8-bit AVR RISC-based microcontroller operating at up to 20 MHz, with 2 KB of flash memory, 128 B of EEPROM, 128 B of SRAM, and 16 general-purpose I/O lines in a 20-pin PDIP package. It is designed for compact, low-power embedded control applications that require flexible programmable logic, timers, serial communication, and mixed-signal measurement. An 8-bit microcontroller is a programmable semiconductor that executes instructions from nonvolatile flash memory and uses registers and internal SRAM while processing sensor, control, and communication tasks. Within the product hierarchy, the ATTINY261A-PU belongs to the Microchip AVR family of reduced-instruction-set controllers. Its compact instruction architecture, 32 working registers, and integrated peripherals make it suitable for embedded systems, consumer appliances, industrial controllers, and compact control products. Key features include a 20 MHz maximum clock rate, 2 KB flash organized as 1K × 16 words, 128 B of EEPROM, 128 B of SRAM, 16 general-purpose I/O lines, and 32 general-purpose working registers. An 8-bit timer/counter with compare modes supports timing and event-control functions. The器件 also combines an ISP-capable architecture with a modest pin count, allowing programming, sensing, switching, and communication functions to share one economical package. The ATTINY261A-PU belongs to Microchip's picoPower-oriented ATtiny261A generation. Its reduced internal-memory footprint distinguishes it from larger AVR microcontrollers, while the 16 I/O lines provide more control and communication resources than very small legacy devices. Its 20 MHz operating capability supports faster control-loop execution than lower-clock 8-bit controllers, although actual throughput depends on the compiled firmware, peripheral configuration, and clock arrangement. Typical uses include compact motor and actuator controllers, low-cost industrial interface modules, LED-lighting controllers, smart sensors, and embedded control boards. The 2 KB flash capacity is best suited to concise firmware, while 128 B of SRAM accommodates working variables and short data buffers. Designers should confirm application code size, timing margin, and peripheral requirements before committing to this memory-limited member of the AVR family. A primary design consideration is pin allocation. Sixteen I/O pins leave limited space for power, ground, programming, reset, communication, and analog functions in the 20-pin PDIP package. Use the manufacturer pin-description table when assigning tracks, preserve access to programming and debugging signals, and avoid loading a pin with a peripheral that prevents its intended alternate function. Component tolerances and decoupling should follow the device's recommended application circuit. This product summary combines the manufacturer's device description with practical guidance on memory sizing, pin planning, firmware limits, and drop-in migration. It also distinguishes the current ATTINY261A-PU ordering code from the documented, functionally identical but obsolete ATTINY261-20PU migration path.

Permintaan RFG Kontak
ATTINY261A-SU - 20MHz 8-bit AVR MCU | Microchip
ATTINY261A-SU

ATTINY261A-SU - 20MHz 8-bit AVR MCU | Microchip

The Microchip Technology ATTINY261A-SU is a 20 MHz, 8-bit AVR RISC microcontroller with 2 KB of Flash memory, 128 bytes of EEPROM, 128 bytes of SRAM, and 16 general-purpose I/O lines in a 20-pin SOIC package. It is designed for compact embedded control tasks that require fast event handling, modest program storage, and a small footprint. An 8-bit AVR microcontroller is a reduced-instruction-computing controller built around the AVR register and instruction architecture. Within the embedded-device hierarchy, it belongs to the MCU class, combines a CPU core with embedded memory and peripherals, and is programmed to supervise sensors, actuators, communications, and user interfaces. The ATTINY261A family is particularly appropriate for cost-sensitive control systems whose firmware and working data fit within 2 KB of Flash and 128 bytes of SRAM. The device provides 32 general-purpose working registers, an 8-bit timer/counter with compare modes, an 8-bit high-speed timer/counter, a Universal Serial Interface, and internal system resources. Its 20 MHz operating speed gives embedded logic sufficient throughput for responsive control, while the 16 I/O lines allow connection of digital inputs, outputs, and mixed signal functions according to the device pin configuration. In-System Programmable Flash supports programming and firmware updates through the AVR programming interface. The ATTINY261A is implemented as a high-performance picoPower 8-bit AVR RISC microcontroller. The ATtiny261A/461A/861A family uses an in-system-programmable Flash architecture and combines the 2 KB, 4 KB, or 8 KB memory configurations shown in the family datasheet. The ATTINY261A-SU corresponds to the 2 KB Flash configuration and is offered in a 20-pin SOIC tube package for standard industrial temperature operation. Typical uses include compact motor or actuator controllers, LED dimming and lighting modules, sensor-interface nodes, low-power consumer accessories, power-control boards, and small industrial automation modules. Its combination of 20 MHz processing, two timers, a Universal Serial Interface, and 16 I/O lines supports control loops, pulse generation, serial communication, and discrete input monitoring without a larger external digital controller. PCB design should preserve short, clean return paths for supply and ground and should follow the pin-specific decoupling and programming-interface guidance in the manufacturer datasheet. Because the SOIC package provides fine-pitch leads, verify land-pattern orientation and inspect solder joints carefully. Confirm the exact peripheral functions assigned to each I/O pin before defining the board schematic because alternate-function assignments vary by device variant and pin. This technical summary organizes the controller’s memory, timing, I/O, package, migration, and design considerations for engineers evaluating the ATTINY261A-SU in a new embedded platform. It also distinguishes the verified original ATtiny261 migration path from unsupported assumptions about cross-brand equivalence, helping design teams make pin-, firmware-, and qualification-aware component decisions.

Permintaan RFG Kontak
ATTINY261A-XU - 20MHz AVR MCU with 2KB Flash | Microchip
ATTINY261A-XU

ATTINY261A-XU - 20MHz AVR MCU with 2KB Flash | Microchip

The Microchip Technology ATTINY261A-XU is a compact 8-bit AVR RISC microcontroller operating at up to 20 MHz, with 2 KB of flash memory, 128 B of SRAM, 128 B of EEPROM, and 16 general-purpose I/O lines in a 20-pin TSSOP package. Its operating supply range of 1.8 V to 5.5 V supports low-voltage battery-powered and conventional 5 V embedded systems. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, data memory, I/O ports, timers, and communication peripherals on one device. The ATTINY261A belongs to the ATtiny family, which sits within the broader hierarchy of AVR microcontrollers, embedded processors, and semiconductor control devices. Its small memory footprint is intended for compact embedded-control tasks rather than general-purpose computing. The ATTINY261A combines 32 general-purpose working registers, an 8-bit timer/counter with compare modes, USI connectivity, and brown-out detection with power-on reset. The 2 KB flash capacity supports a bootloader or a focused control routine, while the 128 B SRAM and 128 B EEPROM provide working data and retained parameter storage. The 16 I/O pins can be assigned to digital inputs, outputs, and interrupt-capable functions according to the device pin configuration. Microchip describes the ATTINY261A as a picoPower 8-bit AVR RISC-based device. Its reduced operating voltage range and low-power design are useful in compact consumer products, industrial controls, sensor nodes, and accessories where board area and energy use matter. The 20-pin TSSOP is surface mount and can be placed on automated production assemblies rather than through-hole breadboards. Typical applications include simple motor or valve controllers, LED status indicators, keypads, battery-powered sensors, communication bridges, and compact embedded modules. In each case, the firmware must fit within 2 KB of flash, while the application should avoid relying on large buffers or storage-intensive libraries. Design the decoupling network and programming connections according to the manufacturer datasheet. Keep the reset path stable, route sensitive communication lines away from switching edges, and confirm that the selected clock and peripheral configuration remain within the device electrical limits. Software should use the chip’s documented timer and USI resources rather than adding unnecessary external components. This product page combines the exact ATTINY261A-XU electrical identity, verified package and memory details, migration context, direct-replacement information, and practical selection guidance to support PCB, firmware, and sourcing decisions.

Permintaan RFG Kontak
ATTINY26L-8MU - 8MHz AVR MCU with 2KB Flash | Microchip
ATTINY26L-8MU

ATTINY26L-8MU - 8MHz AVR MCU with 2KB Flash | Microchip

The Microchip Technology ATTINY26L-8MU is an 8-bit AVR RISC microcontroller operating up to 8 MHz, with 2 KB of Flash program memory, 128 bytes of EEPROM, and 128 bytes of SRAM in a 32-VQFN 5 x 5 mm package. It operates across a 2.7 V to 5.5 V supply range and is specified from -40 °C to +85 °C. An 8-bit microcontroller is a compact embedded-control device that executes firmware to monitor inputs, control outputs, and process data through timers, interrupts, serial interfaces, and analog peripherals. The ATtiny26 belongs to the TinyAVR family, combining a reduced instruction set computer core with Flash memory and mixed-signal peripherals in a small surface-mount package. This hierarchy places it within embedded processing, specifically low-cost, low-power AVR microcontrollers. Key features include a maximum clock frequency of 8 MHz, 2 KB of Flash organized as 1K x 16, 128 bytes of EEPROM, and 128 bytes of internal SRAM. Peripherals include an ADC, I2C, SPI, an analog comparator, an 8/16-bit timer/counter with prescaler, an 8/10-bit high-speed timer/counter with PWM, a programmable watchdog timer, and pin-change interrupts on 11 pins. Low-power idle, noise-reduction, and power-down modes support battery-operated equipment. The AVR enhanced RISC architecture supports single-clock-cycle instruction execution for many common operations, allowing the 8 MHz device to perform control tasks without a larger processor. Its small memory capacity favors compact firmware, while the exposed-pad VQFN construction supports compact PCB placement and thermal dissipation. Designers should use the pin-description table in the manufacturer datasheet when assigning tracks and connecting the exposed pad. Typical uses include compact motor controllers, battery-powered sensors, LED lighting controls, fan controllers, simple security panels, and small industrial automation modules. The ATtiny26L's low-voltage range is particularly useful in 3.3 V systems where a 5 V-only MCU would not provide adequate operating margin. When designing around the ATTINY26L-8MU, place the decoupling capacitor beside each applicable supply pin and preserve the exposed-pad land pattern. Confirm the regulator's startup behavior, output-voltage tolerance, and timing requirements with the firmware configuration. The 2 KB Flash limit also requires disciplined code sizing during toolchain selection and validation. This page combines the manufacturer's ATtiny26 summary information with package details, application guidance, engineering notes, and a strict drop-in replacement assessment. It also highlights when the low-voltage ATtiny26L is preferable to a standard ATtiny26 and where firmware, qualification, or supply requirements should drive a different choice.

Permintaan RFG Kontak
ATTINY26L-8PJ - 8MHz AVR MCU with ADC | Microchip Technology
ATTINY26L-8PJ

ATTINY26L-8PJ - 8MHz AVR MCU with ADC | Microchip Technology

Microchip Technology ATTINY26L-8PJ is an 8-bit AVR microcontroller operating at up to 8 MHz, with 2 KB of Flash memory, 128 bytes of EEPROM, and 128 bytes of SRAM in a 20-pin PDIP package. It provides up to 16 general-purpose I/O lines and integrates an 11-channel, 10-bit analog-to-digital converter with two differential voltage input gain stages. An AVR microcontroller is a compact embedded-control device that combines a CPU core, programmable memory, digital I/O, timers, interrupts, and analog conversion on one integrated circuit. The ATtiny26L belongs to Microchip's low-power AVR family, where low-dropout operation supports portable and battery-powered equipment. Its instruction architecture executes many instructions within a small number of clock cycles, while internal and external oscillator options give designers flexibility in clock selection and system timing. Core features include 32 general-purpose working registers, two 8-bit timer/counter blocks, one timer with PWM outputs, internal and external interrupts, and a programmable watchdog timer. The 10-bit ADC supports 11 input channels, allowing multiple analog sensors to share one peripheral. Its 2 KB Flash capacity stores 1K by 16 bits of program memory, while 128 bytes of EEPROM preserve small quantities of nonvolatile configuration data and 128 bytes of SRAM support working variables. The ATTINY26L-8PJ is useful when a design needs more analog measurement capability than a basic digital controller but not the memory or peripheral complexity of a larger microcontroller. It combines an 8 MHz clock with a low-power AVR architecture and operates across a 2.7 V to 5.5 V supply range. The microcontroller can use its internal oscillator or an external clock source, making it suitable for products where minimizing external components is valuable. Typical uses include compact industrial sensor nodes, low-power battery-operated instruments, analog monitoring modules, lighting controls, teaching platforms, and small embedded-control products. In these applications, the ADC and PWM resources can reduce the need for separate analog and timing components, while EEPROM preserves calibration values or user settings between power cycles. PCB design should provide a stable supply rail and follow the decoupling and grounding guidance in the Microchip ATtiny26 Summary Datasheet. Keep the analog input traces compact, isolate sensitive analog nodes from switching and high-current paths, and verify reset, clock, programming, and unused-pin arrangements before releasing a production layout. This product page combines the verified device specifications with practical application guidance, package information, sourcing instructions, and a cautious drop-in replacement assessment. It highlights where the ATTINY26L-8PJ fits compact embedded systems and where engineers must validate timing, analog performance, programming compatibility, and lifecycle requirements before substitution.

Permintaan RFG Kontak
ATTINY26L-8SU - 8-bit AVR MCU, 2KB Flash, 8MHz | Microchip
ATTINY26L-8SU

ATTINY26L-8SU - 8-bit AVR MCU, 2KB Flash, 8MHz | Microchip

The Microchip (Atmel) ATTINY26L-8SU is a high-performance, low-power 8-bit AVR RISC-based microcontroller combining 2KB of in-system programmable Flash, 128 bytes EEPROM, and 128 bytes SRAM in a 20-pin SOIC package. Operating at up to 8MHz with throughput approaching 1 MIPS per MHz, the device integrates 11-channel 10-bit ADC, two 8-bit Timer/Counters (one with PWM outputs), a programmable Watchdog Timer, and up to 16 general-purpose I/O lines, all in a compact 20-SOIC footprint. An 8-bit AVR microcontroller (MCU) is a single-chip computer built around the AVR enhanced RISC architecture, executing most instructions in a single clock cycle. Within the broader IC taxonomy it belongs to microcontrollers, which are a subclass of embedded processors and a cornerstone of modern power management and embedded control systems. RISC-based microcontrollers offer deterministic instruction timing, low active current, and ultra-low sleep current, making them ideal for battery-powered and always-on designs. Key features include 118 powerful instructions with most single-clock cycle execution, 32 x 8 general-purpose working registers, fully static operation, 10,000-cycle Flash endurance, two differential ADC input gain stages, internal and external oscillator options, and an internal analog comparator. The integrated 10-bit ADC with differential inputs enables direct sensor signal acquisition without external amplifiers. The L-grade silicon supports 2.7V to 5.5V operation versus the standard grade's 4.5V to 5.5V, enabling battery and 3.3V system compatibility. The architecture uses an enhanced Harvard-style bus with separate program and data paths, allowing instruction fetch to overlap with data access. Combined with the 8/16-bit timer with prescaler and the dedicated 8/10-bit high-speed timer/counter with PWM, the device delivers deterministic real-time control in tight power and cost envelopes. Typical applications include sensor signal conditioning, LED lighting control, low-power remote controls, automotive body controllers, battery-powered instrumentation, and small motor/valve control. The wide operating voltage and peripheral mix make the ATtiny26L well-suited to industrial sensor nodes and consumer appliances. When designing, ensure VCC decoupling with 100nF+10uF capacitors close to the supply pin and connect the RESET pin through a 10kohm pull-up. The L-grade variant is recommended for 3.3V operation, while the non-L part is preferred above 4.5V supply for maximum clock speed. This page synthesizes distributor pricing, drop-in alternatives, and design considerations not found in the manufacturer datasheet alone.

Permintaan RFG Kontak
ATTINY28L-4PU - 4MHz 8-Bit AVR MCU | Microchip Technology
ATTINY28L-4PU

ATTINY28L-4PU - 4MHz 8-Bit AVR MCU | Microchip Technology

The Microchip Technology ATTINY28L-4PU is an 8-bit AVR RISC microcontroller with a 4 MHz clock, 2 KB programmable Flash memory, and a 28-pin PDIP package. Its operating voltage range is 2.7 V to 5.5 V, while the AVR architecture supports up to four MIPS of instruction throughput. The device is designed for compact embedded-control, keypad, and low-power peripheral applications where a small amount of nonvolatile program memory and simple digital I/O are sufficient. An 8-bit AVR microcontroller is a programmable semiconductor that combines a CPU core, memory, and peripherals on one integrated circuit. The ATTINY28 belongs to the ATtiny family within the AVR microcontrollers hierarchy, where the core supports single-clock-cycle instruction execution and uses 32 general-purpose registers. Compared with larger AVR devices, it emphasizes a compact instruction set, low-power operation, and a modest memory footprint rather than extensive connectivity or high pin count. Key features include 2 KB of programmable Flash, 32 general-purpose registers, a keyboard interrupt function, and an analog comparator. The specified clock rate is 4 MHz, allowing the processor to execute up to four million instruction cycles per second under the architecture's stated operating conditions. A 2.7 V to 5.5 V supply range supports both 3.3 V and 5 V embedded systems, although timing and peripheral limits must be checked against the selected operating voltage in the manufacturer datasheet. The part uses the low-power CMOS AVR architecture and provides a combination of digital I/O, analog comparison, and interrupt support in a through-hole PDIP package. Its 28-pin package is approximately 0.300 inches wide with a 7.62 mm lead pitch, making it convenient for prototypes, educational systems, and through-hole industrial controllers. Unlike surface-mount variants, the PDIP format is easy to insert and replace with standard breadboards or sockets. Typical applications include keyboard scanners, simple remote controls, small standalone instruments, analog threshold detection, embedded timers, and low-power control boards. The analog comparator is useful when a design needs a simple switching threshold without allocating a larger mixed-signal microcontroller. The 2 KB Flash capacity is appropriate for compact control routines rather than graphical interfaces, networking stacks, or applications with substantial data storage requirements. When designing around the ATTINY28L-4PU, verify the complete pin description, clock requirements, reset behavior, and peripheral limits in the manufacturer datasheet before assigning PCB tracks. Keep the AVR programming interface accessible, provide a stable supply and decoupling arrangement, and use the documented reset strategy. Confirm that 2 KB of program memory remains sufficient for the final bootloader, application code, and interrupt routines. This product summary combines the manufacturer's family-level architecture details with package, memory, voltage, and clock information for the exact ATTINY28L-4PU order code. It also organizes compatible same-family alternatives, comparison points, and practical design guidance so engineers can assess PCB reuse, timing differences, and legacy-product constraints before committing a design to production.

Permintaan RFG Kontak
ATTINY28V-1AU - 8-Bit AVR MCU, 2KB Flash | Microchip
ATTINY28V-1AU

ATTINY28V-1AU - 8-Bit AVR MCU, 2KB Flash | Microchip

Microchip ATTINY28V-1AU is an 8-bit AVR RISC microcontroller with a 1.2 MHz maximum clock, 2 KB of Flash memory organized as 1K x 16 words, and 32-pin TQFP packaging in a 7 x 7 mm footprint. It combines low-power CMOS operation with a compact peripheral set for embedded control, keyboard scanning, and simple analog-interface designs. An 8-bit AVR microcontroller is a compact embedded-control IC that executes instructions using an AVR RISC core. Microcontrollers integrate processor logic, program memory, registers, and peripherals into one package, allowing a design to replace separate processor, memory, and interface components. The ATTINY28 family occupies the low-complexity end of the TinyAVR portfolio and is designed for straightforward control tasks rather than high-volume data processing. The device provides 2 KB of programmable Flash, 32 general-purpose registers, a keyboard interrupt function, and an analog comparator. Its 8-bit architecture provides 32 general-purpose working registers, while the one-cycle execution capability of the AVR core supports throughput approaching 1 MIPS per megahertz. The listed 1.2 MHz operating speed makes it suitable for motor, appliance, keypad, and compact industrial-control designs that do not require a high-performance MCU. The ATTINY28V-1AU operates across the listed 2.5 V, 3.3 V, and 5 V supply options, allowing the same controller family to support different system rails. The keyboard interrupt can reduce polling demands in matrix-keypad designs, while the analog comparator supports threshold detection, basic signal conditioning, and simple sensor-interface functions without requiring a separate comparator IC. Typical applications include keyboard scanners, small appliance controllers, optocoupler and switch interfaces, basic motor-control logic, LED sequencing, and low-cost embedded automation modules. The 32-pin TQFP package provides more connection options than the smaller ATTINY28 packages, making it useful when several I/O lines or power-related pins are needed on a compact PCB. Keep the clock and power rails stable, route decoupling capacitors close to the supply pins, and verify every external pull-up or pull-down value against the configured I/O source current. Before firmware transfer or production use, check the fuse configuration and application circuit against the manufacturer pin-description table so that unused pins, reset behavior, and programming connections remain consistent with the selected board revision. This page combines the ATTINY28 family architecture, package information, application guidance, and technically relevant replacement comparisons. It also organizes pin, sourcing, lifecycle, and design questions into an engineering-focused format that supports faster component evaluation than a basic distributor listing alone.

Permintaan RFG Kontak
ATTINY28V-1PU - 2KB 8-Bit AVR MCU | Microchip Technology
ATTINY28V-1PU

ATTINY28V-1PU - 2KB 8-Bit AVR MCU | Microchip Technology

Microchip Technology ATTINY28V-1PU is an 8-bit AVR RISC microcontroller with 2 KB of flash program memory, a 1.2 MHz clock rating, and 28-pin PDIP packaging. It operates from 1.8 V to 5.5 V and supports 2.5 V, 3.3 V, and 5 V supply arrangements, making it suitable for compact embedded control and low-cost automation systems. An 8-bit microcontroller is a programmable semiconductor that executes instructions from nonvolatile flash memory and uses I/O pins to control sensors, indicators, relays, actuators, and communications interfaces. The ATTINY28 belongs to the AVR family and the broader hierarchy of embedded microcontroller, semiconductor, and programmable-control-device products. Its compact 28-pin package supports both digital and analog signal-chain integration without requiring a complex external processor. The device provides 2 KB of flash memory organized as 1K by 16 bits, a 1.2 MHz maximum clock, and an operating-voltage range of 1.8 V to 5.5 V. The PDIP package is suitable for through-hole assembly, prototyping, educational platforms, and applications that favor a socketable or manually assembled controller. Its stated 2.5 V, 3.3 V, and 5 V operating arrangements simplify supply planning across industrial, consumer, and embedded-control products. The AVR RISC architecture provides an 8-bit processing platform optimized for compact control tasks. The 2 KB program-memory capacity is appropriate for small firmware images containing initialization, periodic measurement, decision logic, and output-control routines. Because the program memory is limited, developers should avoid unnecessary library code and select peripherals according to the actual pin and memory requirements of the end product. Typical uses include small industrial controllers, building-automation endpoints, status indicators, sensor interfaces, LED drivers, and compact embedded modules. The 28-pin PDIP format is especially useful where hand soldering, socket compatibility, or straightforward inspection is more important than the smallest possible surface-mount footprint. A 3.3 V application should also account for the connected peripherals and ensure that their signal levels remain compatible with the selected supply voltage. Decoupling and layout remain important despite the device's modest clock rate. Place the required supply capacitors close to the power pins, route high-current return paths efficiently, and keep switching-node traces away from sensitive input pins. Prototype designs should confirm oscillator, reset, programming, and unused-pin behavior against the manufacturer pin-description table before layout release. This page combines key electrical specifications, package guidance, application-oriented design considerations, and a qualified replacement assessment. It also distinguishes verified device characteristics from fields that require engineering confirmation, helping teams evaluate ATTINY28V-1PU for small embedded-control designs without overlooking memory, voltage, package, or sourcing constraints.

Permintaan RFG Kontak
ATTINY4-MAHR - 8-Bit 12MHz AVR MCU | Microchip Technology
ATTINY4-MAHR

ATTINY4-MAHR - 8-Bit 12MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY4-MAHR is an 8-bit AVR RISC microcontroller with a 12 MHz maximum clock frequency, 512 bytes of program Flash memory, and 32 bytes of SRAM, housed in an 8-pin UDFN/USON package with an exposed pad. The device combines four general-purpose I/O lines with an internal oscillator, a 4-channel 8-bit ADC, SPI and USI connectivity, and dedicated timer resources for compact control applications. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, and peripherals into one package. The ATTINY4 belongs to the TinyAVR family within Microchip's 8-bit AVR portfolio. Its enhanced RISC architecture executes many instructions in a single clock cycle, supporting throughput close to 1 MIPS per MHz while keeping power consumption low enough for compact embedded control, sensing, and actuator-control systems. The principal device characteristics include 512 bytes of Flash organized as 256 words by 16 bits, 32 bytes of SRAM, 12 general-purpose working registers, and an internal oscillator. The 4-channel, 8-bit ADC supports basic analog measurement, while SPI and USI provide serial communication options. An 8-bit timer/counter with two PWM channels and a 16-bit timer/counter support timing, waveform generation, and periodic control tasks. The ATTINY4-MAHR uses the AVR enhanced RISC architecture and a low-power CMOS implementation. Its limited memory footprint makes code size and stack planning important, especially when applications combine ADC readings, serial communications, and PWM outputs. The nickel-palladium-gold termination and green package designation identify the physical construction used for this ordering variant. Typical uses include low-cost sensor nodes, compact LED or fan controllers, simple keypad interfaces, battery-powered instruments, and small industrial control modules. The four available I/O lines favor designs where the MCU performs sequencing or supervisory control rather than high-pin-count connectivity. The 12 MHz operating limit provides more timing headroom than many simple low-power state machines while retaining a compact footprint. Design the exposed-pad connection, decoupling, programming interface, and power entry carefully. Confirm the package drawing, recommended land pattern, voltage limits, and pin multiplexing in the manufacturer datasheet before layout release. The MAHR package suffix should be matched exactly when replacing the device because package and termination variants can have different ordering details. This page organizes the ATtiny4 technical characteristics, sourcing information, and replacement guidance into a compact engineering reference. It also distinguishes verified device functions from parameters that require the exact package drawing, helping designers evaluate the ATTINY4-MAHR before schematic capture, PCB layout, firmware development, and sourcing approval.

Permintaan RFG Kontak
ATTINY4-TS8R - 8-Bit 512B AVR MCU | Microchip
ATTINY4-TS8R

ATTINY4-TS8R - 8-Bit 512B AVR MCU | Microchip

The Microchip Technology ATTINY4-TS8R is a factory-programmable 8-bit AVR microcontroller with 512 bytes of program flash, 32 bytes of SRAM, four I/O pins, and a 10 MHz maximum speed, supplied in an SOT-23-6 surface-mount package. It is designed for compact control, sequencing, and low-cost embedded functions where deterministic single-cycle instruction execution and minimal component count matter more than memory-intensive application processing. An 8-bit microcontroller is a programmable control device that combines a processor core, nonvolatile program memory, data memory, I/O ports, and embedded peripherals on one integrated circuit. The ATTINY4 belongs to the ATtiny family, a TinyAVR subset of the AVR enhanced RISC architecture. Its compact footprint allows it to fit close to sensors, switches, indicator circuits, and actuators, while the four I/O pins provide direct digital interaction with the surrounding system. Verified listings identify 512 bytes of flash, 32 bytes of SRAM, four I/O pins, an internal oscillator, and SOT-23-6 packaging. Distributor and comparison data also identify power-on reset, pulse-width modulation, and watchdog timer support. The manufacturer datasheet describes the ATtiny4/5/9/10 family as a low-power CMOS AVR platform whose enhanced RISC architecture executes most instructions in a single clock cycle, providing throughput close to 1 MIPS per MHz. This execution model is useful for small state machines and tightly bounded control loops. The ATTINY4-TS8R is particularly suitable for simple embedded controllers, sensor interfaces, indicator logic, keyboard or switch scanning, and compact sequencing systems. Its 512-byte program memory limits application complexity, while 32 bytes of SRAM requires careful data allocation and avoidance of unnecessary library overhead. A production design should verify that its reset behavior, oscillator requirements, programming method, and electrical limits fit the intended product. The -TS8R ordering suffix identifies the supplied SOT-23-6 tape-and-reel configuration, while factory programmability allows device-specific firmware to be preloaded before shipment. Designers should confirm the exact programming and labeling workflow with Microchip, account for programming pins and exposed product programming requirements, and validate the assembled firmware under the target voltage, temperature, and load conditions. MicrochipDirect reports the part as factory programmable and in stock, with an estimated shipment date shown for 15-Oct-2026. This page combines the verified distributor specifications, manufacturer-oriented datasheet links, package details, sourcing data, and practical design guidance for ATTINY4-TS8R. Because the supplied search data does not expose the complete electrical timing tables, pin-level programming requirements, or verified pricing tiers, those values remain explicitly identified as needed rather than inferred. This page provides an honest basis for initial design review, procurement comparison, and follow-up validation against the manufacturer documentation.

Permintaan RFG Kontak
ATTINY4-TSHR - 12MHz 8-Bit AVR MCU | Microchip
ATTINY4-TSHR

ATTINY4-TSHR - 12MHz 8-Bit AVR MCU | Microchip

The Microchip Technology ATTINY4-TSHR is a low-power, 8-bit AVR RISC microcontroller with a 12 MHz maximum clock, 512 bytes of in-system programmable Flash memory, and a 32-byte SRAM in a 6-pin SOT-23-6 package. It is designed for compact embedded-control tasks that require deterministic digital I/O, timer support, and low board-space consumption. What is an 8-bit microcontroller? An MCU is an integrated circuit containing a processor core, program memory, data memory, I/O ports, and embedded peripherals. The AVR enhanced RISC architecture uses single-clock-cycle instruction execution, allowing the ATTINY4-TSHR to provide useful control throughput in a very small package. In the hierarchy of electronic components, it belongs to the microcontroller, embedded processor, and semiconductor categories. Key verified features include 512 bytes of Flash memory, 32 bytes of SRAM, a 12 MHz operating frequency, and 8-bit AVR processing. Distributor listings identify the device as a 6-pin SOT-23-6 part and indicate support for 2.5 V, 3.3 V, and 5 V supply variants. Its small package makes it suitable for board-constrained products, but designers should verify the exact electrical limits and pin functions against the manufacturer documentation before layout or firmware release. The ATTINY4-TSHR is positioned for simple control logic rather than high-throughput embedded processing. Its limited memory footprint favors compact programs, state machines, debounce logic, indicators, and basic timing functions. The device can be evaluated for simple sensor conditioning, low-speed communication, actuator control, and auxiliary system functions where the application does not require large buffers or complex networking. Typical design work should begin by confirming the supply voltage, oscillator configuration, I/O direction, reset behavior, and programming interface. Because the package has only six pins, pin multiplexing and exposed-pad or programming considerations require careful schematic review. Use the manufacturer datasheet as the authoritative source for pin names, electrical limits, programming requirements, and operating conditions. A key selection consideration is that ATTINY4-TSHR is a highly constrained MCU with only 512 bytes of Flash and 32 bytes of SRAM. Choose it when the control task is simple and board area is more important than memory capacity or peripheral breadth. For designs needing larger firmware storage, more SRAM, or a broader peripheral set, compare the ATtiny family or another microcontroller family rather than assuming this part can scale. This page combines verified distributor specifications, manufacturer and datasheet references, application guidance, and same-family comparison information to support practical selection. Confirm the exact orderable configuration, lifecycle status, and current commercial terms with Microchip or an authorized distributor before committing a production design.

Permintaan RFG Kontak
ATTINY40-MMH - 8-Bit AVR MCU, 4KB Flash, 12MHz | Microchip Technology
ATTINY40-MMH

ATTINY40-MMH - 8-Bit AVR MCU, 4KB Flash, 12MHz | Microchip Technology

Microchip Technology ATTINY40-MMH is an 8-bit AVR RISC-based microcontroller with 4 KB of ISP Flash memory, 256 bytes of SRAM, 12 general-purpose I/O lines, and operation up to 12 MHz in the MMH package. The ATtiny40 combines a compact low-power CMOS design with an enhanced RISC architecture and an instruction set capable of approaching 1 MIPS per MHz, making it suitable for compact embedded control, sensing, and low-power automation tasks. The ATTINY40 is a TinyAVR microcontroller, a subfamily of the 8-bit AVR family of RISC-based embedded controllers. Its on-chip resources combine program memory, SRAM, general-purpose registers, I/O, timers, and PWM functions in a small device intended for applications where control logic must operate reliably with limited memory and board area. The microcontroller's 12 I/O lines provide interfaces for sensors, switches, indicators, actuators, and external control signals. Key features include 4 KB of ISP Flash memory, 256 bytes of SRAM, 16 general-purpose working registers, an 8-bit timer/counter with two PWM channels, and an additional 8/16-bit timer/counter. The 12 MHz operating speed supports responsive control-loop execution while the low-power CMOS architecture is suitable for battery-operated and embedded systems. The device uses an AVR enhanced RISC core with most instructions executing in a single clock cycle. Typical uses include compact industrial control modules, temperature and environmental monitoring, LED and lighting controllers, small motor-control systems, keypad interfaces, sensor nodes, and programmable control boards. The ATtiny40 is useful when firmware logic, digital I/O, timers, and PWM are required without a high pin count or a larger general-purpose MCU package. When designing around the ATTINY40-MMH, verify the MMH package drawing, pin assignments, clock source, programming interface, and electrical limits in the manufacturer datasheet before PCB layout. Keep ISP programming access available during development, confirm decoupling requirements at the supply pins, and check PWM timer behavior against the intended load. This page combines the device specifications, application guidance, comparison considerations, and practical design notes needed for initial engineering evaluation.

Permintaan RFG Kontak
ATTINY40-SU - 12MHz 8-Bit AVR MCU, 4KB Flash | Microchip
ATTINY40-SU

ATTINY40-SU - 12MHz 8-Bit AVR MCU, 4KB Flash | Microchip

The Microchip Technology ATTINY40-SU is a low-power CMOS 8-bit AVR microcontroller with 4 KB In-System Programming Flash memory, 256 B SRAM, 12 general-purpose I/O lines, and a maximum clock frequency of 12 MHz, all housed in a 20-pin SOIC package. It executes the compact AVR enhanced RISC architecture and combines 16 general-purpose working registers with an 8-bit timer/counter featuring two PWM channels. An 8-bit AVR microcontroller is a compact embedded controller that executes firmware instructions on a Harvard-style architecture, balancing processing capability, memory efficiency, and low power consumption. The AVR family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. TinyAVR devices are particularly useful for cost-sensitive control, monitoring, signal-generation, and communication tasks where a larger MCU would add unnecessary cost or board area. Key verified features include 4 KB flash organized as 2K by 16 words, 256 B SRAM, 12 I/O lines, 16 working registers, and an 8-bit timer/counter with two PWM channels. Its 12 MHz maximum frequency provides substantially more instruction throughput than lower-clock ATtiny devices. The 20-pin SOIC package also supports conventional surface-mount assembly while exposing enough pins for power, clock, programming, reset, I/O, and timer functions. The AVR enhanced RISC architecture supports efficient execution of firmware commonly written for AVR-compatible toolchains. The processor architecture and instruction set should be reviewed against the manufacturer datasheet before porting code, especially when the replacement MCU has a different instruction set, peripheral arrangement, interrupt vector table, or programming interface. The supplied sources do not expose detailed ADC, comparator, timer-resolution, or electrical operating-limit values. Typical uses include compact industrial controls, LED and general-purpose dimming, simple sensor acquisition, small motor or actuator control, battery-powered monitoring, and embedded interface modules. Its two PWM channels can support timing, dimming, or basic proportional actuator functions, while the 12 I/O lines provide flexibility for switches, indicators, sensors, and external logic. When designing a PCB, reserve the programming and reset connections, route clock and decoupling pins according to the manufacturer reference layout, and confirm that every external signal remains within the device’s verified voltage limits. Because the verified snippets do not supply a numerical operating-voltage range, ADC resolution, pin electrical limits, or package dimensions, those values must be checked in the official ATtiny40 documentation before release to manufacturing. This product page combines verified Microchip and distributor data, source-backed availability links, practical application guidance, and explicit data-gap markers. It does not infer unverified electrical specifications or present functional comparators as drop-in replacements when pin or peripheral compatibility has not been demonstrated.

Permintaan RFG Kontak
ATTINY40-SUR - 12MHz 8-Bit AVR MCU, 4KB Flash | Microchip (Tape & Reel)
ATTINY40-SUR

ATTINY40-SUR - 12MHz 8-Bit AVR MCU, 4KB Flash | Microchip (Tape & Reel)

The Microchip Technology ATTINY40-SUR is a low-power CMOS 8-bit AVR microcontroller with 4 KB In-System Programming Flash memory, 256 B SRAM, 12 general-purpose I/O lines, and a maximum clock frequency of 12 MHz, all housed in a 20-pin SOIC package. It executes the compact AVR enhanced RISC architecture and combines 16 general-purpose working registers with an 8-bit timer/counter featuring two PWM channels. An 8-bit AVR microcontroller is a compact embedded controller that executes firmware instructions on a Harvard-style architecture, balancing processing capability, memory efficiency, and low power consumption. The AVR family belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. TinyAVR devices are particularly useful for cost-sensitive control, monitoring, signal-generation, and communication tasks where a larger MCU would add unnecessary cost or board area. Key verified features include 4 KB flash organized as 2K by 16 words, 256 B SRAM, 12 I/O lines, 16 working registers, and an 8-bit timer/counter with two PWM channels. Its 12 MHz maximum frequency provides substantially more instruction throughput than lower-clock ATtiny devices. The 20-pin SOIC package also supports conventional surface-mount assembly while exposing enough pins for power, clock, programming, reset, I/O, and timer functions. The AVR enhanced RISC architecture supports efficient execution of firmware commonly written for AVR-compatible toolchains. The processor architecture and instruction set should be reviewed against the manufacturer datasheet before porting code, especially when the replacement MCU has a different instruction set, peripheral arrangement, interrupt vector table, or programming interface. The supplied sources do not expose detailed ADC, comparator, timer-resolution, or electrical operating-limit values. Typical uses include compact industrial controls, LED and general-purpose dimming, simple sensor acquisition, small motor or actuator control, battery-powered monitoring, and embedded interface modules. Its two PWM channels can support timing, dimming, or basic proportional actuator functions, while the 12 I/O lines provide flexibility for switches, indicators, sensors, and external logic. When designing a PCB, reserve the programming and reset connections, route clock and decoupling pins according to the manufacturer reference layout, and confirm that every external signal remains within the device’s verified voltage limits. Because the verified snippets do not supply a numerical operating-voltage range, ADC resolution, pin electrical limits, or package dimensions, those values must be checked in the official ATtiny40 documentation before release to manufacturing. This product page combines verified Microchip and distributor data, source-backed availability links, practical application guidance, and explicit data-gap markers. It does not infer unverified electrical specifications or present functional comparators as drop-in replacements when pin or peripheral compatibility has not been demonstrated.

Permintaan RFG Kontak
ATTINY40-XU - 8-Bit 12MHz AVR MCU | Microchip Technology
ATTINY40-XU

ATTINY40-XU - 8-Bit 12MHz AVR MCU | Microchip Technology

The Microchip Technology ATTINY40-XU is an 8-bit AVR RISC microcontroller with 12 MHz operation, 4 KB of ISP Flash memory, 256 B of SRAM, and a 20-pin TSSOP package. It is designed for compact embedded control, low-power sensing, and simple actuator or signal-processing systems. An 8-bit AVR microcontroller is a reduced-instruction-computer controller optimized for embedded tasks rather than general-purpose computing. Its single-cycle instruction execution, working registers, and integrated peripherals allow firmware to respond quickly while consuming relatively little processing and board space. The ATTINY40 belongs to the ATtiny family and provides a balanced combination of flash memory, SRAM, I/O, timers, and serial connectivity in one device. Key features include 4 KB of in-system-programmable flash, 256 B of SRAM, 12 general-purpose I/O lines, 16 general-purpose working registers, and an 8-bit timer/counter with two PWM channels. The device operates at up to 12 MHz and is presented in a 20-pin TSSOP package. Distributor data also identifies a 12-channel 10-bit ADC, while the manufacturer page describes an 8/16-bit timer/counter resource. The ATTINY40 architecture combines the AVR core with practical embedded peripherals, including I2C and SPI connectivity identified in the supplied comparison data. This makes it suitable for sensors, configuration interfaces, compact motor-control functions, and low-speed communication nodes. Its small memory footprint favors simple control loops rather than storage-heavy or graphics-oriented applications. Typical uses include building automation, industrial sensing, portable measurement, keypad interfaces, LED indication, and small motor or PWM-driven subsystems. The 12 MHz clock provides useful timing margin for event handling while the 8-bit architecture simplifies firmware and peripheral integration. When designing a board, preserve the required ISP programming interface, decoupling, clock stability, and exposed 12 I/O lines. Confirm the exact pin functions, ADC channels, power limits, and programming connections against the manufacturer datasheet before layout release. This page combines verified distributor specifications, manufacturer information, and engineering guidance without inventing unprovided electrical limits. The information below distinguishes confirmed ATTINY40-XU attributes from parameters that still require direct datasheet verification, helping engineers make faster sourcing and design decisions while maintaining traceability.

Permintaan RFG Kontak
ATTINY40-XUR - 8-Bit 12MHz AVR MCU | Microchip Technology (Tape & Reel)
ATTINY40-XUR

ATTINY40-XUR - 8-Bit 12MHz AVR MCU | Microchip Technology (Tape & Reel)

The Microchip Technology ATTINY40-XUR is an 8-bit AVR RISC microcontroller with 12 MHz operation, 4 KB of ISP Flash memory, 256 B of SRAM, and a 20-pin TSSOP package. It is designed for compact embedded control, low-power sensing, and simple actuator or signal-processing systems. An 8-bit AVR microcontroller is a reduced-instruction-computer controller optimized for embedded tasks rather than general-purpose computing. Its single-cycle instruction execution, working registers, and integrated peripherals allow firmware to respond quickly while consuming relatively little processing and board space. The ATTINY40 belongs to the ATtiny family and provides a balanced combination of flash memory, SRAM, I/O, timers, and serial connectivity in one device. Key features include 4 KB of in-system-programmable flash, 256 B of SRAM, 12 general-purpose I/O lines, 16 general-purpose working registers, and an 8-bit timer/counter with two PWM channels. The device operates at up to 12 MHz and is presented in a 20-pin TSSOP package. Distributor data also identifies a 12-channel 10-bit ADC, while the manufacturer page describes an 8/16-bit timer/counter resource. The ATTINY40 architecture combines the AVR core with practical embedded peripherals, including I2C and SPI connectivity identified in the supplied comparison data. This makes it suitable for sensors, configuration interfaces, compact motor-control functions, and low-speed communication nodes. Its small memory footprint favors simple control loops rather than storage-heavy or graphics-oriented applications. Typical uses include building automation, industrial sensing, portable measurement, keypad interfaces, LED indication, and small motor or PWM-driven subsystems. The 12 MHz clock provides useful timing margin for event handling while the 8-bit architecture simplifies firmware and peripheral integration. When designing a board, preserve the required ISP programming interface, decoupling, clock stability, and exposed 12 I/O lines. Confirm the exact pin functions, ADC channels, power limits, and programming connections against the manufacturer datasheet before layout release. This page combines verified distributor specifications, manufacturer information, and engineering guidance without inventing unprovided electrical limits. The information below distinguishes confirmed ATTINY40-XUR attributes from parameters that still require direct datasheet verification, helping engineers make faster sourcing and design decisions while maintaining traceability.

Permintaan RFG Kontak
ATTINY406-SF - 16MHz 4KB AVR Microcontroller | Microchip
ATTINY406-SF

ATTINY406-SF - 16MHz 4KB AVR Microcontroller | Microchip

The Microchip Technology ATTINY406-SF is an 8-bit AVR tinyAVR functional-safety microcontroller rated for up to 16 MHz, with 4 KB of Flash program memory and 256 bytes of SRAM in a 20-pin SOIC package. The device also provides 128 bytes of EEPROM, 18 I/O pins, and communication peripherals including I2C, SPI, and USART. These characteristics make it suitable for compact industrial, control, sensing, and communication modules where deterministic embedded processing is required in a small surface-mount footprint. A microcontroller is an integrated circuit containing a processor core, program memory, data memory, and peripherals on one semiconductor die. The tinyAVR family combines the general-purpose AVR RISC architecture with event-driven peripherals and low-power sleep capabilities. Within the semiconductor hierarchy, ATTINY406-SF belongs to the TinyAVR 0-series, where its hardware multiplier, analog resources, and event system support efficient control tasks and signal acquisition without requiring a larger processor. Key device features include a 16 MHz maximum operating frequency for the ATTINY406-SF ordering configuration, 4 KB of Flash memory for firmware storage, and 256 bytes of SRAM for working data. The 128-byte EEPROM provides nonvolatile storage for calibration values, configuration data, or counters. An integrated hardware multiplier improves the efficiency of multiply and multiply-accumulate operations, while I2C, SPI, and USART interfaces allow connection to sensors, transceivers, memories, and service ports. The ATTINY406-SF belongs to Microchip's functional-safety-oriented tinyAVR 0-series and is listed by its manufacturer for operation up to 125°C. Its 20-pin SOIC package is larger than QFN options but offers a practical leaded-surface-mount format for assembly and inspection. Typical designs use the microcontroller for supervisory functions, compact sensor nodes, motor or actuator controllers, and low-to-medium-speed communication bridges. Exact voltage limits, converter characteristics, timer channels, and detailed timing parameters should be confirmed against the manufacturer datasheet. For new layouts, place the decoupling network close to the supply pins and route sensitive analog signals away from switching nodes. Confirm oscillator, reset, programming, and exposed-pin requirements in the datasheet pin-description table before release. The 4 KB Flash limit also makes code-size budgeting important when adding communication stacks, safety checks, or field-upgrade features.

Permintaan RFG Kontak