Produk (22.000+)

ATXMEGA32E5-MNR - 32MHz 32KB Flash MCU | Microchip (Tape & Reel)
ATXMEGA32E5-MNR

ATXMEGA32E5-MNR - 32MHz 32KB Flash MCU | Microchip (Tape & Reel)

Microchip Technology ATXMEGA32E5-MNR is an 8/16-bit AVR XMEGA E5 microcontroller operating at 32 MHz with 32 KB of ISP Flash memory, 4 KB of SRAM, and 1 KB of EEPROM in a 32-pin 5 x 5 mm VQFN package. It operates from a 1.6 V to 3.6 V supply and combines a 32 MHz AVR enhanced RISC core with a peripheral-rich mixed-signal architecture. An XMEGA microcontroller is a low-power 8/16-bit RISC controller that integrates a fast CPU, timers, event-system hardware, analog converters, communication peripherals, and memory on a single device. The E5 family is positioned between basic 8-bit AVR devices and larger 32-bit microcontrollers, providing deterministic event handling and high peripheral integration for embedded control systems. Key features include 32 KB of ISP Flash with read-while-write capability, a dedicated 4 KB boot-code section, 1 KB of EEPROM, and 4 KB of SRAM. The eight-channel event system links peripherals directly so that timer, comparator, and other events can trigger internal actions without polling overhead. The device also operates from a 1.6 V to 3.6 V supply, supports 32 MHz operation, and is offered in a compact 32-pin VQFN package. The ATxmega32E5 architecture provides a strong balance of processing performance, analog resources, and power efficiency. Its 32 MHz clock allows deterministic control loops and responsive peripheral servicing, while the XMEGA event system reduces interrupt latency and simplifies timing-sensitive designs. The 32 KB flash configuration is suitable for protocol stacks, motor-control algorithms, and moderately complex control firmware. Typical uses include industrial sensor controllers, compact motor-control nodes, building automation, battery-powered measurement equipment, communication gateways, and embedded instrumentation. The low operating-voltage range also supports energy-conscious designs in which the MCU is powered directly from a regulated low-voltage rail. PCB design should follow the exposed-pad and thermal-pad recommendations in the manufacturer datasheet. Place all decoupling capacitors close to their designated pins, route the exposed pad to a low-impedance ground plane, and confirm the recommended crystal or clock configuration before layout release. This page consolidates device specifications, package details, drop-in alternatives, application guidance, and design considerations into an engineering-focused reference for component selection, schematic review, and PCB layout planning.

Permintaan RFG Kontak
ATXMEGA32E5-MU - 32MHz 32KB AVR MCU | Microchip Technology
ATXMEGA32E5-MU

ATXMEGA32E5-MU - 32MHz 32KB AVR MCU | Microchip Technology

The Microchip Technology ATXMEGA32E5-MU is an 8/16-bit AVR XMEGA E5 microcontroller with a 32 MHz operating frequency, 32 KB of flash memory, 4 KB of SRAM, 1 KB of EEPROM, and a 32-pin QFN package measuring 5 x 5 mm. The -MU suffix denotes the green industrial-temperature configuration listed for this device. It combines a high-performance, low-power AVR enhanced RISC core with an event system and extensive peripheral integration in a compact surface-mount package. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, volatile working memory, and peripherals such as timers, serial interfaces, and event-control hardware. The AVR enhanced RISC architecture belongs to the microcontroller hierarchy and supports efficient control-oriented instruction execution. Microchip positions the XMEGA E5 family between general-purpose embedded control and higher-performance 8/16-bit applications requiring rich event handling and flexible timing resources. The ATXMEGA32E5 provides 32 KB of in-system programmable flash, with read-while-write capability, plus a 4 KB boot-code section. Its 4 KB SRAM provides working space for application state, buffers, and stack operations, while 1 KB of EEPROM supports nonvolatile data retention. The eight-channel event system can connect peripherals directly, reducing processor intervention for timing-sensitive tasks. A programmable multi-level interrupt system helps organize responses across the integrated peripherals. The AVR XMEGA E5 architecture integrates flash, SRAM, EEPROM, the event system, interrupt handling, and communication peripherals on one device. Its 32 MHz clock rate gives designers additional timing resolution and processing capacity compared with lower-clocked 8-bit controllers. The family is designed for low-power, peripheral-rich embedded control, making it appropriate for designs in which deterministic peripheral interaction matters as much as conventional sequential software execution. Typical uses include industrial control modules, compact sensor nodes, motor-control peripherals, communications equipment, and mixed-signal embedded systems. Its 32 KB flash is suitable for moderate firmware loads, while the event system is especially useful when timers, counters, waveform generation, or peripheral-to-peripheral signaling must be coordinated without continuous central-processor polling. The 5 x 5 mm QFN also supports space-constrained boards requiring more integration than a small 8-pin device can offer. When laying out a board, follow the manufacturer pin-description and package-drawing tables rather than relying on generic QFN conventions. Keep the device's decoupling capacitors close to the appropriate supply pins and route programming, reset, and communications signals with attention to noise immunity. Confirm the complete peripheral mix, clock plan, and pin assignments in the manufacturer datasheet before finalizing the PCB footprint. This product page combines the ATXMEGA32E5 family specifications, package information, sourcing guidance, application fit, and drop-in replacement analysis with practical design considerations. It helps engineers compare memory, package, architecture, and lifecycle considerations before committing the 32-QFN footprint to a design.

Permintaan RFG Kontak
ATXMEGA32X1-UU - 8MHz 32KB 8-Bit MCU | Microchip
ATXMEGA32X1-UU

ATXMEGA32X1-UU - 8MHz 32KB 8-Bit MCU | Microchip

The Microchip Technology ATXMEGA32X1-UU is an 8-bit microcontroller operating at 8 MHz, with 32 KB of flash memory and a 2.1 V to 5.5 V supply range. The device is offered in a WLCSP package intended for compact, space-constrained electronic products, and it is identified for industrial-temperature operation. Its small package and low-voltage operating range make it relevant to embedded control, sensor-interface, and compact portable-system designs where board area and power consumption are important design constraints. A microcontroller is a semiconductor integrated circuit that combines a processor core, programmable memory, data memory, and peripheral interfaces on one device. In the product hierarchy, a microcontroller belongs to the embedded processor and embedded-control category, where it sits above a general-purpose CPU and below a complete control system. Instead of requiring separate memory and interface components, the ATXMEGA32X1-UU consolidates the core processing and embedded-control functions into one component, reducing board footprint and simplifying assembly compared with a discrete processor design. The three headline identifiers for this device are its 8 MHz operating speed, 32 KB flash memory, and 2.1 V to 5.5 V supply-voltage range. Flash memory retains programmed code when power is removed, supporting repeatable field operation without a separate external program-memory device. The 8 MHz operating rate provides a clear timing reference for the embedded-control role, while the 5.5 V maximum stated operating voltage allows the controller to operate from a regulated low-voltage rail. The WLCSP package further supports dense PCB layouts. The ATXMEGA32X1-UU belongs to Microchip's ATXMEGA 8-bit microcontroller family. Its 32 KB flash allocation places it in the small-to-medium embedded-memory range: enough for compact control firmware while avoiding the larger memory and package demands of high-end microcontrollers. Because the exact peripheral complement, RAM capacity, pin mapping, and electrical timing characteristics must be verified before schematic capture, the manufacturer datasheet and package drawing should govern final interface assignments, programming configuration, and clock decisions. Typical design opportunities include compact sensor nodes, industrial control modules, low-voltage embedded instruments, portable accessories, and space-constrained peripheral controllers. In each case, the WLCSP package can help minimize PCB area, while the 2.1 V to 5.5 V operating range supports integration with common low-voltage power systems. Firmware should be configured around the device's actual peripheral resources and current limits, and the PCB should provide suitable power, decoupling, programming access, and exposed-pad thermal management. A primary design consideration is package-level integration. WLCSP devices require assembly processes capable of handling a small, fine-pitch land pattern, and the exposed thermal pad must be connected to the ground and copper plane as specified by the manufacturer. Confirm pin assignments, pad dimensions, programming signals, and recommended capacitor placement from the official package documentation before releasing a PCB footprint. This page consolidates the confirmed ATXMEGA32X1-UU specifications, package characteristics, sourcing links, application guidance, and replacement considerations. It is designed to help engineers identify whether the 8 MHz, 32 KB-flash, industrial-temperature WLCSP device fits a compact embedded-control design and to distinguish a validated drop-in replacement from merely similar microcontrollers.

Permintaan RFG Kontak
ATXMEGA384C3-MH - 32MHz 384KB Flash MCU | Microchip Technology
ATXMEGA384C3-MH

ATXMEGA384C3-MH - 32MHz 384KB Flash MCU | Microchip Technology

The Microchip Technology ATXMEGA384C3-MH is an 8/16-bit AVR XMEGA microcontroller with a 32 MHz clock, 384 KB of programmable Flash plus an 8 KB boot-code section, and a 64-QFN package measuring 9 x 9 mm. The device also includes 4 KB of EEPROM, 32 KB of SRAM, a two-channel DMA controller, and a 12-bit ADC. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, data memory, and peripherals on one integrated circuit. The AVR XMEGA family belongs to the broader embedded-controller hierarchy and uses an enhanced RISC architecture designed to execute instructions efficiently. Its combination of memory capacity and peripheral integration makes it suitable for embedded control systems that require more local storage than a basic general-purpose microcontroller. The ATXMEGA384C3-MH provides 384 KB of in-system programmable Flash with read-while-write capability, plus a separate 8 KB boot-code section. A 4 KB EEPROM supports nonvolatile parameter storage, while 32 KB of SRAM provides working memory for control logic, buffers, and communication stacks. The two-channel DMA controller can move data between peripherals and memory, reducing processor involvement in suitable data-transfer operations. The MCU operates from 1.62 V to 3.6 V and uses the AVR enhanced RISC architecture with a maximum clock frequency of 32 MHz. A 12-bit ADC supports analog measurements, while the 64-QFN package places the device in a compact surface-mount form factor. The industrial-temperature variant is specified for operation from -40 °C to +85 °C, making it appropriate for equipment expected to operate across extended ambient conditions. Typical uses include industrial sensor controllers, building and access-control equipment, industrial communication gateways, compact data loggers, and embedded control modules. The ATXMEGA384C3-MH is especially useful when firmware, boot code, EEPROM-backed configuration, and moderate SRAM requirements must coexist in one MCU rather than being split across external memory devices. Board design should preserve the device's low-voltage supply quality and provide decoupling close to the power pins. Firmware should also use the dedicated boot section for controlled startup or field-update workflows and configure DMA only after confirming that the selected peripheral transfers do not conflict with timing-sensitive interrupts. This page organizes the key MCU specifications, sourcing information, equivalent-device constraints, and application guidance into a practical engineering reference. It also highlights the distinction between genuine pin-compatible replacements and package or temperature-ordering variants that require different assembly or qualification decisions.

Permintaan RFG Kontak
ATXMEGA384D3-AN - 32MHz 384KB AVR XMEGA Microcontroller | Microchip Technology
ATXMEGA384D3-AN

ATXMEGA384D3-AN - 32MHz 384KB AVR XMEGA Microcontroller | Microchip Technology

The Microchip Technology ATXMEGA384D3-AN is a high-performance, low-power 8/16-bit AVR XMEGA microcontroller with 384 KB of in-system programmable Flash memory, 4 KB of EEPROM, 32 KB of SRAM, and a maximum operating frequency of 32 MHz. The device is supplied in a 64-pin TQFP package measuring 14 x 14 mm and is identified as a green, industrial-temperature part with a 1.6 V to 3.6 V operating voltage range. Its 8 KB boot-code section supports read-while-write operation in the Flash memory region. AVR XMEGA microcontrollers are 8/16-bit RISC microcontrollers positioned between general-purpose 8-bit MCUs and more complex 32-bit embedded processors. The XMEGA D3 family combines a high-performance AVR core with a four-channel event system, programmable peripherals, and extensive memory in a single integrated circuit. This makes it useful when a design requires more SRAM and Flash capacity than a basic 8-bit AVR while retaining the simplicity of the AVR software and peripheral model. Key features include 384 KB of Flash storage with an 8 KB boot section, 4 KB of EEPROM, 32 KB of SRAM, a 32 MHz clock rating, and a four-channel event system. The large memory footprint supports protocol stacks, configuration data, logging, graphical data handling, and firmware updates. The ATXMEGA384D3-AN is also listed with a 64-TQFP package and a 1.6 V to 3.6 V supply range. The MCU architecture supports an 8/16-bit instruction set with a high-performance pipeline, hardware multipliers, and dedicated event-system resources for deterministic signal routing. The event system is particularly useful for applications requiring direct communication between timers, comparator outputs, and other peripherals without routing every event through the CPU. Typical uses include industrial control and automation, sensor hubs, communication equipment, embedded gateways, data-acquisition systems, and consumer devices requiring more memory than a basic 8-bit MCU. The part is appropriate where a compact 64-pin surface-mount controller is needed and where 1.6 V to 3.6 V operation and a maximum temperature rating of 105 degrees C are important design constraints. For PCB implementation, use the manufacturer's pin description and package drawings when assigning power, ground, programming, and peripheral signals. The TQFP footprint requires careful escape routing between closely spaced pins, and the device should be placed to minimize noise coupling from switching converters and high-current traces. This product page combines the device specifications, package information, sourcing details, and application guidance needed for initial design review.

Permintaan RFG Kontak
ATXMEGA64A1-AU - 32MHz 64KB Flash MCU | Microchip Technology
ATXMEGA64A1-AU

ATXMEGA64A1-AU - 32MHz 64KB Flash MCU | Microchip Technology

The Microchip Technology ATXMEGA64A1-AU is a low-power, high-performance 8/16-bit AVR XMEGA A1 microcontroller with a 32 MHz clock, 64 KB of self-programming Flash memory, 4 KB of SRAM, and a 100-lead TQFP package measuring 14 mm by 14 mm. It combines an enhanced RISC core with four-channel DMA, an eight-channel event system, a programmable multilevel interrupt controller, and extensive timer and communications peripherals. The -AU ordering code identifies the industrial-temperature 100-lead TQFP configuration. An 8/16-bit microcontroller is a programmable semiconductor that integrates a CPU, nonvolatile program memory, data memory, interrupt handling, and peripherals into one device. The ATXMEGA64A1-AU belongs to the AVR XMEGA family, which extends the AVR architecture into a higher-performance 8/16-bit platform with simultaneous operation of two 16-bit registers and hardware accelerators for data movement and event routing. The 64 KB Flash program memory includes a 4 KB boot-code section and supports read-while-write operation. Internal memory is completed by 4 KB of SRAM and 2 KB of EEPROM. Peripheral integration includes four-channel DMA, an eight-channel event system, 78 general-purpose I/O lines, a 16-bit real-time counter, and eight flexible 16-bit timer/counter modules with compare and PWM channels. These resources reduce external logic and improve responsiveness in embedded control designs. The enhanced AVR RISC architecture executes instructions in a single clock cycle and delivers throughput approaching 1 MIPS per MHz. Its integrated peripherals can transfer data without repeated CPU intervention, while the event system connects timer, comparator, ADC, and other peripherals through configurable event channels. The ATXMEGA64A1-AU therefore supports responsive embedded control without requiring a separate DSP or high-speed external bus interface for many common tasks. Typical uses include industrial automation controllers, data acquisition systems, motor-control and PWM platforms, communications equipment, and connected sensor nodes. The device is particularly useful when a design needs more peripheral capacity and processing throughput than a small 8-bit MCU, while retaining the familiar AVR development ecosystem and integrated on-chip memories. PCB implementation should preserve the manufacturer's recommended power, clock, decoupling, programming, and signal-routing arrangements. The 100-lead TQFP footprint requires careful escape routing around the device, while the 1.6 V to 3.6 V operating range requires attention to regulator tolerance, signal levels, and load-dependent voltage droop. This product page organizes the core device specifications, package information, design considerations, application guidance, and pin-compatible family alternatives into a single engineering reference for MCU selection and board design.

Permintaan RFG Kontak
ATXMEGA64A1-AUR 32MHz 64KB Flash MCU | Microchip | TQFP-100
ATXMEGA64A1-AUR

ATXMEGA64A1-AUR 32MHz 64KB Flash MCU | Microchip | TQFP-100

The Microchip Technology ATXMEGA64A1-AUR is an 8/16-bit AVR XMEGA A1 microcontroller operating at up to 32 MHz, with 64 KB of self-programming Flash memory, 4 KB of SRAM, and 2 KB of EEPROM in a 100-pin TQFP package. The ATXMEGA64A1-AUR combines a high-performance AVR core with extensive mixed-signal peripherals and flexible external interfaces for industrial control, data acquisition, and embedded automation. An 8/16-bit AVR microcontroller is a compact embedded-processing device whose architecture executes instructions using an 8-bit register-oriented model while supporting 16-bit operations through paired registers. The XMEGA A1 family extends the AVR architecture into the power-management IC ecosystem with a strong peripheral mix, multiple timer channels, event-system routing, direct-memory access, and a real-time counter. This makes the family useful when deterministic control and specialized hardware peripherals are required without a higher-complexity processor core. Key device features include in-system-programmable Flash with read-while-write operation, 2 KB of internal EEPROM, 4 KB of SRAM, a four-channel DMA controller, an eight-channel event system, a programmable multilevel interrupt controller, and a 16-bit real-time counter. Eight flexible 16-bit timer/counter blocks provide timing, compare, and PWM functions, while the A1 family also includes an external bus interface and extensive general-purpose I/O. The AVR instruction set combines compact 16-bit opcodes, multiply-and-multiply-accumulate support, and dedicated event-handling peripherals. Read-while-write Flash operation allows code execution to continue during suitable programming activity, while the DMA and event system reduce CPU intervention for data movement and time-critical signal routing. These characteristics distinguish the device from simpler 8-bit AVR microcontrollers that provide fewer autonomous peripherals. Typical uses include industrial sensor acquisition, motor and actuator control, communications gateways, data loggers, and compact embedded control platforms. The multiple timers support motor PWM, waveform generation, and periodic servicing, while the external bus interface can connect the controller to additional digital devices. The 100-pin TQFP package also provides enough I/O and power connectivity for systems requiring several peripheral functions on one board. When designing around the ATXMEGA64A1-AUR, use the manufacturer datasheet pin table for every signal and exposed-pad connection, and preserve the required decoupling and programming-interface layout. Confirm that the chosen peripheral mix matches the exact A1 device rather than assuming that all XMEGA family members share identical pin assignments. The manufacturer also identifies the A1 device as not recommended for new designs and directs new designs toward ATxmega64A1U. This product analysis combines the exact device characteristics with practical peripheral-selection guidance, replacement considerations, and PCB-focused design notes. It helps engineers distinguish exact ordering-code variants, evaluate low-power migration options, and plan firmware, decoupling, timing, and mixed-signal layouts before committing a 100-pin design to production.

Permintaan RFG Kontak
ATXMEGA64A1-C7U - 32MHz 64KB Flash AVR MCU | Microchip
ATXMEGA64A1-C7U

ATXMEGA64A1-C7U - 32MHz 64KB Flash AVR MCU | Microchip

The Microchip Technology ATXMEGA64A1-C7U is an 8/16-bit AVR XMEGA A1 microcontroller with a 32 MHz operating frequency, 64 KB self-programming Flash memory, 4 KB SRAM, 2 KB EEPROM, and a 100-VFBGA 7 x 7 mm package. The device also provides an external bus interface, a four-channel DMA controller, an eight-channel event system, a programmable multilevel interrupt controller, 78 general-purpose I/O lines, and a 16-bit real-time counter. An AVR XMEGA microcontroller belongs to the 8/16-bit RISC microcontroller category and combines a high-performance AVR core with advanced peripherals on a single mixed-signal device. The XMEGA A1 family is designed for embedded systems that need more than basic digital control, including deterministic data movement, event-driven peripheral coordination, high-resolution timing, and flexible communications through the external bus interface. Its architecture sits below 32-bit microcontrollers in processing width but can provide high peripheral integration for industrial, communications, and control applications. The ATXMEGA64A1 family supports in-system programmable Flash with read-while-write operation, internal EEPROM, and internal SRAM. Its eight flexible 16-bit timer/counter channels support compare and PWM functions, while the event system can connect peripherals without requiring continuous CPU intervention. Four-channel DMA reduces the processing burden associated with data movement, and the programmable multilevel interrupt controller helps organize real-time event handling. The 78 available I/O lines also provide substantial interface density despite the compact 7 x 7 mm package. The 32 MHz AVR core operates as an 8/16-bit processor, allowing efficient access to 16-bit data while retaining compatibility with 8-bit peripherals and general-purpose I/O. The external bus interface can connect the controller to additional memory or peripheral devices, while the DMA and event system support partitioned real-time architectures. These resources make the MCU suitable for designs where deterministic response, concurrency, and peripheral integration matter more than the broader software ecosystem of a general-purpose 32-bit processor. Typical uses include industrial data acquisition, communications equipment, sensor hubs, embedded control panels, and compact control systems. Its 64 KB Flash capacity supports moderate embedded applications, while 2 KB EEPROM provides nonvolatile parameter storage and 4 KB SRAM supports working data. In a data-acquisition design, DMA can transfer samples while the event system and timers coordinate acquisition timing. In a communications controller, the external bus interface can connect memory or peripherals while the CPU manages the protocol stack. Designers should confirm pin multiplexing, ball assignments, power requirements, clock options, and peripheral conflicts using the manufacturer datasheet and package information before committing the PCB layout. The 100-VFBGA package also demands assembly capability for inspection, rework, and reliable solder-joint inspection. For new production designs, the manufacturer lists the standard ATxmega64A1 as not recommended for new designs and directs users toward ATxmega64A1U. This product page consolidates the verified device description, manufacturer and distributor references, lifecycle guidance, package details, and design-focused distinctions between the ATXMEGA64A1-C7U and the recommended ATXMEGA64A1U family, providing practical information for engineering review and sourcing decisions.

Permintaan RFG Kontak
ATXMEGA64A1-CU - 32MHz 64KB AVR MCU | Microchip Technology
ATXMEGA64A1-CU

ATXMEGA64A1-CU - 32MHz 64KB AVR MCU | Microchip Technology

Microchip Technology ATXMEGA64A1-CU is an 8/16-bit AVR XMEGA A1 microcontroller operating at 32 MHz, with 64 KB of self-programming Flash memory, 4 KB SRAM and 2 KB EEPROM in a 100-CBGA package measuring 9 mm by 9 mm. The device operates from a 1.6 V to 3.6 V supply and provides 34 I/O ports. Its integrated peripherals include a direct memory access controller, PWM channels, brown-out detection and reset, power-on reset and a watchdog timer. The MCU is intended for low-power, high-performance embedded designs that require substantial Flash storage, rapid peripheral access and a compact surface-mount package. According to Microchip, the ATxmega64A1 family is not recommended for new designs and Microchip identifies ATxmega64A1U as its preferred successor. An 8/16-bit AVR microcontroller is a compact embedded-processing device that combines a processor core, nonvolatile program memory, volatile working memory, communication peripherals and mixed-signal or timing functions on one integrated circuit. In the product hierarchy, the ATXMEGA64A1-CU is an MCU, part of the broader integrated-circuit and embedded-processing categories. Its XMEGA architecture supports 8-bit and 16-bit instruction execution, making it useful where deterministic control, moderate arithmetic performance and low system complexity are more important than the application processor performance of a high-end Cortex-M device. The MCU's 32 MHz operating frequency is its principal performance figure, while its 64 KB Flash memory provides room for application code and boot code. The manufacturer product page also identifies a 4 KB boot-code section, 4 KB SRAM and 2 KB EEPROM. Brown-out detection, power-on reset and the watchdog timer support reliable startup and continued operation. Four-channel DMA reduces peripheral data-transfer overhead, while the PWM and external bus interface extend its usefulness for motor control, industrial automation and connected embedded equipment. The 1.6 V to 3.6 V operating range permits use with common low-voltage digital rails. The 100-CBGA package provides 100 ball-grid connections and a compact 9 mm by 9 mm footprint, but its fine-pitch ball array requires a PCB with high-quality routing and assembly capability. Unlike a simple microcontroller package, a CBGA also demands careful power-plane design, via-in-pad or equivalent escape-routing strategies, and assembly processes capable of handling the package's fine pitch. The manufacturer lists this family as not recommended for new designs, so lifecycle planning is essential. Typical applications include industrial automation controllers, compact motor-control systems, sensor-conditioning hubs, communication modules and low-power embedded products. The combination of DMA, PWM, 64 KB Flash and a 32 MHz clock is especially useful in cost-sensitive systems that need several concurrent control functions without using a higher-complexity processor. Because the part is not recommended for new designs, engineers should evaluate ATxmega64A1U before committing a new PCB to this package. The primary design consideration is package and lifecycle risk. ATXMEGA64A1-CU can be maintained in an existing 100-CBGA design, but new products should verify recommended-device migration, pin compatibility, memory-map differences, toolchain support and long-term procurement before committing. The verified distributor data does not provide a complete ball assignment or exposed-pad connection, so the package drawing must be checked against the current Microchip documentation before PCB release. This page consolidates the verified manufacturer and distributor specifications, lifecycle guidance, pricing, package constraints and same-family migration information. It also distinguishes the legacy ATXMEGA64A1-CU from the manufacturer-recommended ATxmega64A1U path and identifies which replacement decisions still require pin-level validation rather than relying on broad functional similarity.

Permintaan RFG Kontak
ATXMEGA64A1-CUR - 32MHz 64KB AVR MCU | Microchip Technology (Tape & Reel)
ATXMEGA64A1-CUR

ATXMEGA64A1-CUR - 32MHz 64KB AVR MCU | Microchip Technology (Tape & Reel)

Microchip Technology ATXMEGA64A1-CUR is an 8/16-bit AVR XMEGA A1 microcontroller operating at 32 MHz, with 64 KB of self-programming Flash memory, 4 KB SRAM and 2 KB EEPROM in a 100-CBGA package measuring 9 mm by 9 mm. The device operates from a 1.6 V to 3.6 V supply and provides 34 I/O ports. Its integrated peripherals include a direct memory access controller, PWM channels, brown-out detection and reset, power-on reset and a watchdog timer. The MCU is intended for low-power, high-performance embedded designs that require substantial Flash storage, rapid peripheral access and a compact surface-mount package. According to Microchip, the ATxmega64A1 family is not recommended for new designs and Microchip identifies ATxmega64A1U as its preferred successor. An 8/16-bit AVR microcontroller is a compact embedded-processing device that combines a processor core, nonvolatile program memory, volatile working memory, communication peripherals and mixed-signal or timing functions on one integrated circuit. In the product hierarchy, the ATXMEGA64A1-CUR is an MCU, part of the broader integrated-circuit and embedded-processing categories. Its XMEGA architecture supports 8-bit and 16-bit instruction execution, making it useful where deterministic control, moderate arithmetic performance and low system complexity are more important than the application processor performance of a high-end Cortex-M device. The MCU's 32 MHz operating frequency is its principal performance figure, while its 64 KB Flash memory provides room for application code and boot code. The manufacturer product page also identifies a 4 KB boot-code section, 4 KB SRAM and 2 KB EEPROM. Brown-out detection, power-on reset and the watchdog timer support reliable startup and continued operation. Four-channel DMA reduces peripheral data-transfer overhead, while the PWM and external bus interface extend its usefulness for motor control, industrial automation and connected embedded equipment. The 1.6 V to 3.6 V operating range permits use with common low-voltage digital rails. The 100-CBGA package provides 100 ball-grid connections and a compact 9 mm by 9 mm footprint, but its fine-pitch ball array requires a PCB with high-quality routing and assembly capability. Unlike a simple microcontroller package, a CBGA also demands careful power-plane design, via-in-pad or equivalent escape-routing strategies, and assembly processes capable of handling the package's fine pitch. The manufacturer lists this family as not recommended for new designs, so lifecycle planning is essential. Typical applications include industrial automation controllers, compact motor-control systems, sensor-conditioning hubs, communication modules and low-power embedded products. The combination of DMA, PWM, 64 KB Flash and a 32 MHz clock is especially useful in cost-sensitive systems that need several concurrent control functions without using a higher-complexity processor. Because the part is not recommended for new designs, engineers should evaluate ATxmega64A1U before committing a new PCB to this package. The primary design consideration is package and lifecycle risk. ATXMEGA64A1-CUR can be maintained in an existing 100-CBGA design, but new products should verify recommended-device migration, pin compatibility, memory-map differences, toolchain support and long-term procurement before committing. The verified distributor data does not provide a complete ball assignment or exposed-pad connection, so the package drawing must be checked against the current Microchip documentation before PCB release. This page consolidates the verified manufacturer and distributor specifications, lifecycle guidance, pricing, package constraints and same-family migration information. It also distinguishes the legacy ATXMEGA64A1-CUR from the manufacturer-recommended ATxmega64A1U path and identifies which replacement decisions still require pin-level validation rather than relying on broad functional similarity.

Permintaan RFG Kontak
ATXMEGA64A1U-AU - 32MHz 64KB AVR MCU | Microchip
ATXMEGA64A1U-AU

ATXMEGA64A1U-AU - 32MHz 64KB AVR MCU | Microchip

The Microchip Technology ATXMEGA64A1U-AU is a low-power, high-performance 8/16-bit AVR XMEGA microcontroller with a 32 MHz clock, 64 KB self-programming Flash memory, 4 KB SRAM, and 2 KB EEPROM. The device operates from 1.6 V to 3.6 V and is packaged in a 100-pin TQFP measuring 14 mm by 14 mm. An 8/16-bit AVR XMEGA microcontroller is an embedded-processing device that combines an AVR RISC core, programmable memories, real-time control peripherals, and serial interfaces in one integrated circuit. The XMEGA family extends the familiar AVR architecture with an event system, direct memory access, flexible timing channels, and enhanced interrupt handling, making it suitable for control-intensive systems requiring deterministic peripheral coordination. The ATXMEGA64A1U-AU includes 64 KB of self-programming Flash, organized as 32K by 16 words, together with a 4 KB boot-code section. Its 4 KB SRAM supports working data, while 2 KB of EEPROM provides nonvolatile storage. Integrated resources include a four-channel DMA controller, an eight-channel event system, an external bus interface, and communication peripherals supporting I2C, SPI, UART, and IrDA-oriented applications. The ATXMEGA64A1U-AU also integrates a 12-bit analog subsystem. Available descriptions identify a 16-channel, 12-bit ADC and four 12-bit DAC channels. These converters allow the controller to acquire sensor data and generate controlled analog voltage levels without requiring separate converters in every design. Its 32 MHz maximum operating frequency supports responsive protocol handling and multi-peripheral operation within a compact embedded platform. Typical applications include industrial control modules, data-acquisition equipment, communications controllers, building automation, instrumentation, and low-power embedded products. The combination of 64 KB Flash, 4 KB SRAM, 2 KB EEPROM, DMA, event-system hardware, and analog conversion is particularly useful when firmware must coordinate multiple sensors and communications interfaces without excessive CPU intervention. PCB design should preserve clean analog and digital power distribution, route sensitive analog signals away from switching nodes, and follow the manufacturer’s pin and decoupling recommendations. Firmware planning should account for boot code, self-programming behavior, memory organization, and the interactions among DMA, timers, and the event system. The AU ordering code identifies the specified temperature, package, and reel configuration. This product page consolidates the manufacturer specifications, ordering details, technical comparisons, and practical design guidance needed to evaluate the ATXMEGA64A1U-AU for a new embedded-control design.

Permintaan RFG Kontak
ATXMEGA64A1U-CU - 32MHz 64KB USB Microcontroller | Microchip
ATXMEGA64A1U-CU

ATXMEGA64A1U-CU - 32MHz 64KB USB Microcontroller | Microchip

The Microchip Technology ATXMEGA64A1U-CU is a low-power, high-performance 8/16-bit AVR XMEGA microcontroller with 64 KB of self-programming Flash, 4 KB of SRAM, 2 KB of EEPROM, a 32 MHz operating frequency, and a 100-CBGA 9 x 9 mm package. Its operating voltage range is 1.6 V to 3.6 V. An 8/16-bit AVR microcontroller is a programmable semiconductor that combines a processor core, nonvolatile program memory, data memory, and peripherals in one device. The XMEGA A1U family belongs to the hierarchy of 8-bit microcontrollers, embedded processors, and semiconductor ICs. Its multi-channel DMA controller, event system, external bus interface, and USB capability make it suitable for connected embedded-control equipment. Key features include 64 KB of Flash organized as 32K x 16, a separate 4 KB boot-code section, 4 KB of SRAM, and 2 KB of EEPROM. The device operates from 1.6 V to 3.6 V at up to 32 MHz. A 4-channel DMA controller transfers data without continuous processor intervention, while the 8-channel event system links peripherals through hardware events and reduces software timing overhead. The A1U architecture combines an 8-bit AVR instruction set with hardware support for efficient 16-bit operations. Its peripheral set includes an external bus interface for communication with external memory or peripheral devices. The USB-enabled A1U designation supports designs that require wired USB connectivity in addition to the standard serial and timer resources found in an embedded MCU. Typical uses include industrial automation controllers, USB-connected data-acquisition units, low-power sensor hubs, communications equipment, and compact consumer products. The 100-CBGA package supports dense PCB layouts, although its fine ball pitch requires careful escape routing, inspection, and assembly-process control. For PCB implementation, route the power and ground connections as short and wide as practical, place decoupling capacitors close to the supply pins, and follow the manufacturer package and pin-assignment drawings when assigning BGA balls. Confirm the exact USB transceiver integration, clock arrangement, boot configuration, and peripheral pin multiplexing against the manufacturer device documentation before releasing the layout. This product page combines the exact ordering code, memory configuration, package information, sourcing structure, comparison parameters, and practical BGA design guidance needed to evaluate ATXMEGA64A1U-CU for an embedded USB controller design.

Permintaan RFG Kontak
ATXMEGA64A3-AU - 64KB Flash AVR XMEGA A3 MCU 32MHz TQFP-64 | Microchip
ATXMEGA64A3-AU

ATXMEGA64A3-AU - 64KB Flash AVR XMEGA A3 MCU 32MHz TQFP-64 | Microchip

The Microchip Technology ATXMEGA64A3-AU is an 8/16-bit AVR XMEGA A3 microcontroller delivering 32 MIPS throughput at 32 MHz, with 64 KB of in-system programmable Flash, 4 KB SRAM, 2 KB EEPROM, and 4 KB boot code section, housed in a 64-pin TQFP (14x14 mm) package. It integrates a 4-channel DMA controller, an 8-channel event system, a programmable multi-level interrupt controller, and a 16-bit Real Time Counter (RTC). The device operates from 1.6 V to 3.6 V, making it suitable for both battery-powered and 3.3 V regulated rails. An AVR XMEGA microcontroller is a high-performance 8/16-bit RISC architecture that extends the classic AVR core with a wider instruction set, hardware multiplier, and rich on-chip peripherals. Within the broader taxonomy, the ATXMEGA64A3 belongs to the XMEGA A3 family, which is the general-purpose branch of the XMEGA line designed for low-power embedded control with deterministic interrupt handling and event-driven peripherals. The XMEGA core architecture (AVR -> 8-bit MCU -> microcontroller -> semiconductor) achieves 1 MIPS per MHz efficiency, so a 32 MHz clock produces 32 MIPS of compute, an attractive ratio for power-constrained designs. Key features include 50 general-purpose I/O lines, seven 16-bit Timer/Counters with PWM and compare modes, seven USARTs, two two-wire interfaces (TWI/I2C), two SPI peripherals, a 12-bit ADC and 12-bit DAC, a four-channel DMA controller, and a cryptographic AES/DES engine. The self-programmable Flash supports Read-While-Write, allowing firmware updates without halting application code execution, while the on-chip boot section enables secure bootloader-based field upgrades. The 64-pin TQFP (14x14 mm) is a mature surface-mount package with reliable manufacturability and good thermal performance for moderate-power designs. The 1.6 V minimum supply extends the part into single-cell Li-ion (nominally 3.7 V) and energy-harvesting applications, while the on-chip peripherals reduce external component count. The architecture's deterministic interrupt latency and peripheral event system make it particularly well suited to real-time control loops. Typical applications include industrial sensor hubs, building automation controllers, smart metering nodes, USB device bridges, HMI panels with TFT drives, and low-power wireless sensor nodes. Designers typically select this part when they need deterministic event handling, generous on-chip peripherals, and the flexibility of a self-programmable Flash with bootloader support, all at low supply voltage. When designing with this device, ensure that VDDCORE is properly decoupled and that PDI/PDO programming lines are accessible on the board for in-system programming. The XMEGA event system routes peripheral triggers without CPU intervention, so designers should map out event channels before committing to a final pinout. Peripherals not in use should be clock-gated via the PR register to minimize power draw in sleep modes. This page synthesizes distributor pricing, drop-in XMEGA A3 alternatives, package-aware comparison, and design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA64A3-AUR - 64KB Flash AVR XMEGA A3 MCU 32MHz TQFP-64 | Microchip (Tape & Reel)
ATXMEGA64A3-AUR

ATXMEGA64A3-AUR - 64KB Flash AVR XMEGA A3 MCU 32MHz TQFP-64 | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA64A3-AUR is an 8/16-bit AVR XMEGA A3 microcontroller delivering 32 MIPS throughput at 32 MHz, with 64 KB of in-system programmable Flash, 4 KB SRAM, 2 KB EEPROM, and 4 KB boot code section, housed in a 64-pin TQFP (14x14 mm) package. It integrates a 4-channel DMA controller, an 8-channel event system, a programmable multi-level interrupt controller, and a 16-bit Real Time Counter (RTC). The device operates from 1.6 V to 3.6 V, making it suitable for both battery-powered and 3.3 V regulated rails. An AVR XMEGA microcontroller is a high-performance 8/16-bit RISC architecture that extends the classic AVR core with a wider instruction set, hardware multiplier, and rich on-chip peripherals. Within the broader taxonomy, the ATXMEGA64A3 belongs to the XMEGA A3 family, which is the general-purpose branch of the XMEGA line designed for low-power embedded control with deterministic interrupt handling and event-driven peripherals. The XMEGA core architecture (AVR -> 8-bit MCU -> microcontroller -> semiconductor) achieves 1 MIPS per MHz efficiency, so a 32 MHz clock produces 32 MIPS of compute, an attractive ratio for power-constrained designs. Key features include 50 general-purpose I/O lines, seven 16-bit Timer/Counters with PWM and compare modes, seven USARTs, two two-wire interfaces (TWI/I2C), two SPI peripherals, a 12-bit ADC and 12-bit DAC, a four-channel DMA controller, and a cryptographic AES/DES engine. The self-programmable Flash supports Read-While-Write, allowing firmware updates without halting application code execution, while the on-chip boot section enables secure bootloader-based field upgrades. The 64-pin TQFP (14x14 mm) is a mature surface-mount package with reliable manufacturability and good thermal performance for moderate-power designs. The 1.6 V minimum supply extends the part into single-cell Li-ion (nominally 3.7 V) and energy-harvesting applications, while the on-chip peripherals reduce external component count. The architecture's deterministic interrupt latency and peripheral event system make it particularly well suited to real-time control loops. Typical applications include industrial sensor hubs, building automation controllers, smart metering nodes, USB device bridges, HMI panels with TFT drives, and low-power wireless sensor nodes. Designers typically select this part when they need deterministic event handling, generous on-chip peripherals, and the flexibility of a self-programmable Flash with bootloader support, all at low supply voltage. When designing with this device, ensure that VDDCORE is properly decoupled and that PDI/PDO programming lines are accessible on the board for in-system programming. The XMEGA event system routes peripheral triggers without CPU intervention, so designers should map out event channels before committing to a final pinout. Peripherals not in use should be clock-gated via the PR register to minimize power draw in sleep modes. This page synthesizes distributor pricing, drop-in XMEGA A3 alternatives, package-aware comparison, and design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA64A3-MH - 32MHz 64KB AVR Microcontroller | Microchip
ATXMEGA64A3-MH

ATXMEGA64A3-MH - 32MHz 64KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA64A3-MH is a low-power 8/16-bit AVR XMEGA A3 microcontroller with a 32 MHz clock, 64 KB of self-programming Flash memory, 4 KB SRAM, and 2 KB EEPROM in a 64-QFN (9 x 9 mm) package. It provides up to 32 MIPS throughput and operates from 1.6 V to 3.6 V. An AVR XMEGA microcontroller is an embedded semiconductor that combines a processor core, program and data memory, communication peripherals, timers, and event-management hardware in one device. The XMEGA A3 family sits within the broader hierarchy of 8/16-bit AVR microcontrollers, embedded controllers, and microcontrollers used for low-power control and signal-processing applications. The ATXMEGA64A3-MH includes 64 KB of Flash organized as 32K x 16, a separate 4 KB boot-code section, 4 KB SRAM, and 2 KB EEPROM. Its four-channel DMA controller and eight-channel event system allow data movement and event routing between peripherals without requiring every transfer to be handled directly by the CPU. At a maximum clock of 32 MHz, the device delivers up to 32 MIPS throughput. This processing capability, together with the 16-bit Flash organization and event-system architecture, supports responsive control loops and coordinated peripheral operations while maintaining the low-power characteristics associated with the AVR XMEGA family. Typical uses include industrial control, sensor acquisition, communication modules, low-power embedded systems, and compact control platforms. The 1.6 V to 3.6 V operating range makes the device suitable for low-voltage embedded systems, while 64 KB of Flash provides room for firmware, configuration data, and a boot section within one microcontroller. Designers should verify the complete 64-pin pinout, exposed-pad connection, clock configuration, decoupling requirements, and peripheral assignments against the manufacturer datasheet before layout. The 64-QFN footprint also requires careful thermal-via placement and PCB-land-pattern verification to maintain reliable heat transfer from the exposed pad. This page consolidates verified manufacturer and distributor information, separates the exact ATXMEGA64A3-MH characteristics from related family variants, and identifies which drop-in alternatives require firmware or peripheral review before substitution.

Permintaan RFG Kontak
ATXMEGA64A3U-MH - 32MHz 64KB AVR Microcontroller | Microchip
ATXMEGA64A3U-MH

ATXMEGA64A3U-MH - 32MHz 64KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA64A3U-MH is a low-power, high-performance 8/16-bit AVR XMEGA A3U microcontroller with a 32 MHz maximum clock, 64 KB self-programming Flash, 4 KB SRAM, 2 KB EEPROM, and a 64-QFN 9 x 9 mm package. It combines an AVR enhanced RISC core, four-channel DMA controller, eight-channel event system, and a peripheral set designed for low-power embedded control. An 8/16-bit microcontroller is a semiconductor device that executes embedded software from nonvolatile Flash while using SRAM for working data and EEPROM for parameters that must retain their values when power is removed. The ATXMEGA A3 family combines a microcontroller core, timers, communication interfaces, analog peripherals, and general-purpose I/O in one device, supporting industrial, communications, control, and data-acquisition designs. The device provides 64 KB of self-programming Flash with Read-While-Write capability, including a 4 KB boot-code section, alongside 4 KB of SRAM and 2 KB of EEPROM. Its four-channel DMA controller transfers data without continuous CPU intervention, while the eight-channel event system links peripherals for deterministic event routing. The family also includes up to 50 general-purpose I/O lines. At 32 MHz, the AVR enhanced RISC architecture can reach approximately 1 MIPS per MHz and up to 32 MIPS of throughput. Seven flexible 16-bit timer/counters provide compare and PWM functions, and the family includes seven USARTs, two TWI interfaces, and a 16-bit real-time counter. These integrated resources reduce the need for external timers, serial transceivers, and data-movement circuitry. Typical applications include industrial monitoring, connected sensor nodes, building automation, low-power serial controllers, embedded data loggers, and compact control platforms. The combination of DMA, event-system routing, multiple serial interfaces, and 32-bit processing performance is especially useful when several peripheral operations must coexist under a deterministic embedded software architecture. PCB design should preserve the exposed-pad land pattern and thermal-via requirements specified by the manufacturer for the 64-QFN package. Power, decoupling, clock, and programming nets should follow the datasheet reference layout, while unused I/O pins should be configured according to the device’s reset and input-buffer guidelines. This page combines the manufacturer device specifications, package identification, family-level peripheral details, sourcing information, and application-oriented engineering guidance to support component selection and board-level implementation.

Permintaan RFG Kontak
ATXMEGA64A4-AU - 32MHz AVR XMEGA Microcontroller | Microchip
ATXMEGA64A4-AU

ATXMEGA64A4-AU - 32MHz AVR XMEGA Microcontroller | Microchip

The Microchip Technology ATXMEGA64A4-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 64 KB self-programming Flash memory, 4 KB SRAM, and 2 KB EEPROM in a 44-TQFP 10 x 10 mm package. It supports operating voltages from 1.6 V to 3.6 V and provides up to 32 MIPS of throughput at 32 MHz. An 8/16-bit microcontroller is a programmable semiconductor that combines a CPU core, nonvolatile program memory, data memory, and peripherals in one device. The AVR enhanced RISC architecture belongs to the broader embedded-control hierarchy: microcontroller → 8/16-bit MCU → embedded processor → semiconductor. XMEGA devices are designed for low-power industrial control, communications, data acquisition, and real-time peripheral-heavy systems. Key features include 64 KB of self-programming Flash with read-while-write capability, a separate 4 KB boot-code section, 4 KB of SRAM, and 2 KB of EEPROM. The device provides 34 general-purpose I/O lines, a 12-channel 12-bit ADC, five flexible 16-bit timer/counter channels with PWM support, five USARTs, and communication interfaces including I2C, SPI, IrDA, and USB. A four-channel DMA controller and eight-channel event system help move data and synchronize peripherals without excessive CPU intervention. The ATXMEGA64A4-AU combines an enhanced AVR RISC core with a peripheral set intended for embedded control rather than general-purpose computing. Its 32 MHz operating frequency provides up to 32 MIPS throughput, while the event system can route signals among timer, comparator, ADC, and communication resources. The external bus interface extends system connectivity when additional memory or peripherals are required. Typical uses include industrial automation, building automation, sensor aggregation, data-acquisition systems, touch interfaces, communications equipment, and low-power embedded control. Its 34 I/O lines suit products requiring several digital interfaces, while the ADC and event system support mixed-signal and time-sensitive measurements. The USB interface can simplify connections to host systems when the selected board configuration includes the required support circuitry. For layout, keep the 32 MHz clock and decoupling layout compact, observe all supply and ground-pin requirements, and follow the package pin-connection guidance in the manufacturer datasheet. Provide stable 1.6 V to 3.6 V operation across temperature, and verify the selected programming, crystal, and communication interfaces during firmware bring-up. This page combines the manufacturer specifications, package and interface details, sourcing guidance, application analysis, and practical design considerations needed to evaluate the ATXMEGA64A4-AU for an embedded-control design.

Permintaan RFG Kontak
ATXMEGA64A4-MU - 32MHz AVR XMEGA MCU | Microchip Technology
ATXMEGA64A4-MU

ATXMEGA64A4-MU - 32MHz AVR XMEGA MCU | Microchip Technology

Microchip Technology ATXMEGA64A4-MU is an 8/16-bit AVR XMEGA A4 microcontroller with a 32 MHz clock, 64 KB flash program memory, 4 KB SRAM, and a 44-pin VQFN package measuring 7 x 7 mm. The device combines an 8/16-bit RISC-style AVR core with 34 I/O ports and extensive mixed-signal peripherals for compact embedded control, measurement, communication, and industrial applications. An AVR XMEGA microcontroller is an 8-bit microcontroller family that combines a Harvard-style processor architecture, event-system peripherals, DMA, and mixed-signal functions. The ATXMEGA64A4-MU occupies the XMEGA A4 level of the AVR product hierarchy and provides enough flash memory and SRAM for moderate control tasks while supporting communication and analog signal acquisition. Key device features include 64 KB of flash memory organized as 32K x 16 words, 4 KB of SRAM, a 32 MHz operating clock, and 34 I/O ports. Integrated peripherals include multiple I2C, SPI, and UART/USART interfaces, a DMA controller, a 12-bit ADC, and two 12-bit DAC channels. The advertised operating range of 1.8 V, 2.5 V, or 3.3 V supply options supports low-voltage embedded systems. The ATXMEGA64A4-MU combines general-purpose digital control with on-chip analog conversion. The 12-bit ADC supports sensor acquisition, while the dual 12-bit DACs can generate controllable analog voltages for test, measurement, or actuator interfaces. Hardware DMA can transfer data between peripherals and SRAM, reducing interrupt-driven processor overhead in designs that handle multiple serial or analog data streams. Typical applications include industrial automation, motor and board control, building and climate-control equipment, factory automation, power tools, HVAC systems, networking and metering equipment, handheld battery-powered products, large household appliances, optical systems, and medical devices. The 44-pin VQFN package supports space-constrained board layouts where 34 I/O positions and mixed-signal functions are valuable. PCB design should preserve clean analog and digital return paths, place decoupling capacitors close to the supply pins, and follow the package-specific exposed-pad land pattern and thermal-via recommendations in the manufacturer datasheet. Confirm the selected clock, memory, ADC, DAC, and communication settings in the final device configuration rather than relying only on generic family assumptions. This product record consolidates the confirmed device specifications, practical application guidance, source links, and verified drop-in considerations. It also distinguishes confirmed facts from parameters that require confirmation from the manufacturer documentation before schematic release, PCB layout, or production sourcing.

Permintaan RFG Kontak
ATXMEGA64A4U-AU - 64KB Flash 32 MIPS AVR XMEGA MCU | Microchip
ATXMEGA64A4U-AU

ATXMEGA64A4U-AU - 64KB Flash 32 MIPS AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA64A4U-AU is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller delivering up to 32 MIPS throughput at 32 MHz, with 64 KB of self-programming Flash, 4 KB SRAM, 2 KB EEPROM and a 4 KB boot code section, housed in a 44-pin TQFP package rated for industrial temperature (-40C to +85C) operation from 1.6 V to 3.6 V. An AVR XMEGA microcontroller is a member of the 8/16-bit RISC microcontroller family that combines an enhanced Harvard architecture with rich on-chip peripherals such as DMA, an event system and a USB 2.0 Full-Speed controller. In the broader taxonomy it sits under MCU -> RISC microcontroller -> embedded controller -> semiconductor. The XMEGA series is engineered for deterministic, low-latency I/O handling at modest clock rates while keeping active and sleep current far below typical ARM Cortex-M parts. Key features include a 4-channel DMA controller, an 8-channel peripheral event system that lets peripherals trigger each other without CPU intervention, a hardware AES/DES crypto engine, a 12-bit 1 MSPS ADC, two 12-bit DACs and an integrated USB 2.0 Full-Speed device/host controller. The device also exposes an external bus interface for memory-mapped peripherals and provides up to 34 programmable I/O pins with configurable drive strength and slew-rate control. The A4U die is implemented on a low-leakage CMOS process, and the core supports 136 new instructions including hardware multiply, single-cycle GPIO access and atomic bit manipulation. The integrated peripheral event system routes peripheral-to-peripheral triggers across the device with deterministic sub-microsecond latency, allowing sensor data acquisition and PWM updates to occur while the core sleeps, dramatically lowering average power for battery-powered designs. Typical applications include USB human-interface devices such as keyboards, mice and game controllers, industrial sensor hubs, portable medical monitors, USB-to-UART bridge dongles, low-power IoT edge nodes and battery-backed data loggers. The wide 1.6 V to 3.6 V supply range is well suited to single-cell Li-ion and 2xAA chemistries. When designing with this part, place the 0.1 uF VCC decoupling caps adjacent to each power pin and follow the USB DP/DN 90-ohm differential layout rules to maintain USB-IF compliance. The internal 32 kHz calibrated oscillator can serve as the RTC source without an external crystal for cost-sensitive designs. This page synthesizes distributor pricing, drop-in alternatives within the XMEGA family and practical design notes not aggregated by DigiKey, Mouser or Octopart.

Permintaan RFG Kontak
ATXMEGA64A4U-CU - 32MHz 64KB AVR Microcontroller | Microchip
ATXMEGA64A4U-CU

ATXMEGA64A4U-CU - 32MHz 64KB AVR Microcontroller | Microchip

The Microchip Technology ATXMEGA64A4U-CU is a low-power 8/16-bit AVR XMEGA A4U microcontroller operating up to 32 MHz with 64 KB of self-programming Flash memory, 4 KB SRAM, and 2 KB EEPROM in a 49-VFBGA 5x5 mm package. Its operating supply range is 1.6 V to 3.6 V, and the device includes an external bus interface, four-channel DMA controller, and eight-channel event system. An 8/16-bit AVR microcontroller is a compact embedded-control semiconductor that combines a processor core, programmable Flash memory, data memory, peripherals, and communication interfaces on one die. The ATXMEGA64A4U-CU belongs to the hierarchy of 8-bit MCU, embedded microcontroller, and semiconductor, combining deterministic 8-bit processing with a 16-bit instruction architecture and higher-performance peripherals for control-oriented embedded systems. Key features include 64 KB of self-programming Flash, 4 KB of SRAM, and 2 KB of EEPROM for persistent configuration data. The 32 MHz operating speed supports responsive control loops, while the four-channel DMA controller reduces CPU intervention during data transfers. The eight-channel event system can route events between peripherals, helping implement timing-sensitive control sequences without relying entirely on software polling. The device also supports up to 32 general-purpose I/O pins according to the manufacturer product description, enabling dense interface designs without external logic. Its 49-VFBGA package is only 5x5 mm, making it suitable for space-constrained products, although its fine-pitch ball array requires careful PCB layout, assembly, and inspection. The -CU ordering code identifies the green, industrial-temperature device variant listed for a 1.6 V to 3.6 V supply range. Typical uses include industrial sensor controllers, compact motor-control modules, low-power embedded instruments, communication equipment, and portable measurement products. The combination of internal DMA, an event system, EEPROM, and self-programming Flash is especially useful when data must be transferred or stored locally while the CPU handles control and communications. Developers can update firmware through the supported programming workflow and retain configuration parameters across power cycles. PCB design should prioritize clean supply distribution and correct ball-grid layout. Place decoupling capacitors close to the supply balls, route sensitive signals away from fast-switching nodes, and follow the manufacturer footprint and assembly guidelines exactly. Firmware replacement should be planned around Flash endurance, bootloader behavior, and the device's supported programming tools. This product page combines the manufacturer's device capabilities, package and memory details, drop-in family alternatives, comparison data, and practical PCB guidance. It is intended to help engineers confirm footprint compatibility, memory requirements, operating voltage, and migration options before incorporating the ATXMEGA64A4U-CU into a compact embedded-control design.

Permintaan RFG Kontak
ATXMEGA64A4U-MH - 64KB Flash XMEGA A4U 32MHz MCU | Microchip
ATXMEGA64A4U-MH

ATXMEGA64A4U-MH - 64KB Flash XMEGA A4U 32MHz MCU | Microchip

The Microchip Technology (formerly Atmel) ATXMEGA64A4U-MH is a low-power, high-performance 8/16-bit AVR XMEGA A4U microcontroller integrating 64 KB of self-programming Flash, 4 KB boot code section, 4 KB SRAM, and 2 KB EEPROM in a 44-pin VQFN (7x7) package. It runs up to 32 MHz, supports an operating voltage range of 1.6 V to 3.6 V, and exposes 34 general-purpose I/O lines plus an external bus interface for memory-mapped peripherals. An XMEGA A4U microcontroller is a member of the AVR enhanced RISC architecture family aimed at low-power, peripheral-rich embedded designs. Within the broader hierarchy, the ATXMEGA64A4U-MH sits between classic ATmega 8-bit MCUs (simpler peripherals, lower DMA integration) and ARM Cortex-M devices (higher MIPS, wider 32-bit datapath). The XMEGA line is purpose-built for deterministic event-driven control with hardware-accelerated data movement, bridging the gap between traditional 8-bit AVR and 32-bit ARM designs. Key features include a four-channel DMA controller that offloads memory-to-peripheral transfers, an eight-channel event system that routes peripheral triggers without CPU intervention, and a programmable multi-level interrupt controller for prioritized response. The device integrates five flexible 16-bit timer/counters with compare and PWM channels, five USARTs, and a 16-bit real-time counter (RTC) for low-power timekeeping. Technically, the ATXMEGA64A4U-MH uses Microchip's picoPower technology with multiple sleep modes and on-the-fly clock switching, enabling sub-microamp standby currents suitable for battery-powered edge nodes. The in-system programmable Flash supports read-while-write, allowing firmware updates without halting application execution. Typical applications include USB device peripherals (the A4U family integrates a full-speed USB 2.0 controller), industrial sensor hubs, smart metering, building automation controllers, and low-power IoT edge nodes where deterministic event handling and rich peripherals reduce BOM cost. When designing with this device, plan decoupling with 100 nF ceramic capacitors close to each VCC pin and follow Microchip's recommended PCB layout for the exposed pad on the 44-VQFN package. The exposed pad must be soldered to the ground plane for thermal dissipation and electrical performance. This page synthesizes verified distributor pricing, drop-in VQFN-44 alternatives from the same XMEGA family, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
ATXMEGA64B1-AN - 32MHz 64KB Flash AVR XMEGA MCU | Microchip
ATXMEGA64B1-AN

ATXMEGA64B1-AN - 32MHz 64KB Flash AVR XMEGA MCU | Microchip

The Microchip Technology ATXMEGA64B1-AN is an 8/16-bit AVR XMEGA microcontroller with 32 MHz maximum clock speed, 64 KB self-programming flash, 8 KB SRAM, 2 KB EEPROM, and a 100-pin TQFP package. It operates from 1.6 V to 3.6 V and is specified for a 105°C temperature range. An XMEGA microcontroller combines an AVR CPU with a highly integrated event system, direct memory access, multi-level interrupts, and numerous hardware peripherals. The ATXMEGA64B1 specifically provides a two-channel DMA controller, a four-channel event system, 53 general-purpose I/O lines, a real-time counter, and an LCD controller capable of driving up to a 4 x 40 segment display. It also includes a full-speed USB device interface. The device provides 64 KB of in-system programmable flash with read-while-write capability and an 8 KB boot-code section. Its 8 KB SRAM supports buffered communication, event-driven data acquisition, and protocol processing, while 2 KB of EEPROM provides nonvolatile storage for calibration data, configuration parameters, and serial numbers. These resources are suitable for connected control panels, compact industrial controllers, and USB-connected measurement products. The XMEGA architecture places peripherals on an event system rather than relying only on software polling. Signals generated by timers, analog comparators, and other peripherals can be routed to DMA channels and interrupt resources, reducing CPU intervention in time-critical tasks. The two-channel DMA controller is especially useful for transferring ADC results, display data, or communications buffers while the CPU executes other tasks. Typical applications include utility metering, home automation, climate control, industrial control, sports equipment, USB connectivity, power tools, medical equipment, toys, eTokens, and fire-alarm systems. The 100-pin TQFP package exposes the LCD, USB, analog, timer, communications, and general-purpose I/O resources needed by these multi-function designs. PCB design should preserve USB trace geometry, provide adequate decoupling at the supply pins, and route high-speed or sensitive analog signals away from switching nodes. Confirm the device pin functions and alternate peripheral mappings in the manufacturer datasheet before assigning PCB nets, particularly for LCD segments, USB differential pairs, and pins with multiple peripheral functions.

Permintaan RFG Kontak
ATXMEGA64B1-AU - 32MHz 64KB AVR MCU | Microchip
ATXMEGA64B1-AU

ATXMEGA64B1-AU - 32MHz 64KB AVR MCU | Microchip

The Microchip Technology ATXMEGA64B1-AU is a 32 MHz 8/16-bit AVR XMEGA B1 microcontroller with 64 KB self-programming Flash, 8 KB SRAM, 2 KB EEPROM, and 53 general-purpose I/O lines in a 100-pin TQFP package. The device operates from 1.62 V to 3.6 V and combines a peripheral-rich architecture with a USB Full Speed Device controller and an LCD driver capable of supporting a 4x40 segment display. An 8/16-bit microcontroller is a compact embedded-processing semiconductor intended to execute firmware, control peripherals, and manage real-time system tasks. The AVR XMEGA B1 family uses the AVR enhanced RISC architecture and belongs to the broader hierarchy of 8-bit microcontroller, embedded processor, and system-on-chip semiconductor devices. Its combination of nonvolatile program memory, static data memory, communication peripherals, and event-driven hardware makes it suitable for control-intensive products rather than general-purpose computing. Key features include 64 KB of in-system self-programmable Flash with read-while-write capability, an 8 KB boot-code section, 8 KB SRAM, and 2 KB EEPROM. The integrated two-channel DMA controller transfers data without repeated CPU intervention, while the four-channel event system links peripherals through hardware events. A USB Full Speed Device interface supports direct USB connectivity, and the LCD controller can drive up to 4x40 segments. Up to 32 MIPS of execution capability supports responsive control and signal-processing workloads. The XMEGA B1 architecture integrates timers, communication interfaces, analog functions, and event-system resources around the AVR core. Its event system can route activity among peripherals without routing every event through the central processor, reducing interrupt overhead in deterministic designs. Read-while-write Flash supports firmware updates and data storage workflows, while DMA is useful for transferring display, communication, or sampled data blocks. The microcontroller also includes a real-time counter for timekeeping applications. Typical uses include USB-connected human-interface devices, segmented LCD instruments, industrial control panels, low-power embedded controllers, and communications equipment. The 53 I/O pins provide substantial board-level connectivity, while the USB device interface simplifies direct host connectivity. The 4x40-segment LCD capability is particularly useful in meters, counters, laboratory equipment, and appliance interfaces where a character-oriented display is preferred. When designing around the ATXMEGA64B1-AU, verify every signal against the 100-pin package pin description and keep USB routing layout-controlled on a multilayer board. The 1.62 V to 3.6 V operating range supports low-voltage designs, but external components, USB transceiver requirements, and display characteristics still require system-level validation. Firmware should also account for the independent Flash, EEPROM, SRAM, and peripheral resources when planning updates and data retention. This product page consolidates device specifications, package details, practical application guidance, and a parameter comparison that can help engineers evaluate the ATXMEGA64B1-AU before schematic capture or firmware development.

Permintaan RFG Kontak
ATXMEGA64B1-AUR - 32MHz 64KB AVR MCU | Microchip (Tape & Reel)
ATXMEGA64B1-AUR

ATXMEGA64B1-AUR - 32MHz 64KB AVR MCU | Microchip (Tape & Reel)

The Microchip Technology ATXMEGA64B1-AUR is a 32 MHz 8/16-bit AVR XMEGA B1 microcontroller with 64 KB self-programming Flash, 8 KB SRAM, 2 KB EEPROM, and 53 general-purpose I/O lines in a 100-pin TQFP package. The device operates from 1.62 V to 3.6 V and combines a peripheral-rich architecture with a USB Full Speed Device controller and an LCD driver capable of supporting a 4x40 segment display. An 8/16-bit microcontroller is a compact embedded-processing semiconductor intended to execute firmware, control peripherals, and manage real-time system tasks. The AVR XMEGA B1 family uses the AVR enhanced RISC architecture and belongs to the broader hierarchy of 8-bit microcontroller, embedded processor, and system-on-chip semiconductor devices. Its combination of nonvolatile program memory, static data memory, communication peripherals, and event-driven hardware makes it suitable for control-intensive products rather than general-purpose computing. Key features include 64 KB of in-system self-programmable Flash with read-while-write capability, an 8 KB boot-code section, 8 KB SRAM, and 2 KB EEPROM. The integrated two-channel DMA controller transfers data without repeated CPU intervention, while the four-channel event system links peripherals through hardware events. A USB Full Speed Device interface supports direct USB connectivity, and the LCD controller can drive up to 4x40 segments. Up to 32 MIPS of execution capability supports responsive control and signal-processing workloads. The XMEGA B1 architecture integrates timers, communication interfaces, analog functions, and event-system resources around the AVR core. Its event system can route activity among peripherals without routing every event through the central processor, reducing interrupt overhead in deterministic designs. Read-while-write Flash supports firmware updates and data storage workflows, while DMA is useful for transferring display, communication, or sampled data blocks. The microcontroller also includes a real-time counter for timekeeping applications. Typical uses include USB-connected human-interface devices, segmented LCD instruments, industrial control panels, low-power embedded controllers, and communications equipment. The 53 I/O pins provide substantial board-level connectivity, while the USB device interface simplifies direct host connectivity. The 4x40-segment LCD capability is particularly useful in meters, counters, laboratory equipment, and appliance interfaces where a character-oriented display is preferred. When designing around the ATXMEGA64B1-AUR, verify every signal against the 100-pin package pin description and keep USB routing layout-controlled on a multilayer board. The 1.62 V to 3.6 V operating range supports low-voltage designs, but external components, USB transceiver requirements, and display characteristics still require system-level validation. Firmware should also account for the independent Flash, EEPROM, SRAM, and peripheral resources when planning updates and data retention. This product page consolidates device specifications, package details, practical application guidance, and a parameter comparison that can help engineers evaluate the ATXMEGA64B1-AUR before schematic capture or firmware development.

Permintaan RFG Kontak