Produk (21.000+)

EFM32G232F128G-E-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash | Silicon Labs
EFM32G232F128G-E-QFP64

EFM32G232F128G-E-QFP64 - 32MHz ARM Cortex-M3 MCU, 128KB Flash | Silicon Labs

The Silicon Labs EFM32G232F128G-E-QFP64 is an ARM Cortex-M3 Gecko microcontroller IC running at 32 MHz with 128 kB (128K x 8) of flash program memory and 16 kB of RAM, housed in a 64-pin TQFP (10 mm x 10 mm) surface-mount package. It is a member of the energy-friendly EFM32 Gecko family designed for ultra-low-power embedded designs. An ARM Cortex-M3 microcontroller (MCU) is a 32-bit processor core from Arm Holdings featuring the Thumb-2 instruction set, hardware divide, atomic bit-banding, and a deterministic nested vector interrupt controller (NVIC). Cortex-M3 sits in the Cortex-M family hierarchy (Cortex-M0/M0+ -> Cortex-M3 -> Cortex-M4/M7) and is widely used for cost-sensitive embedded applications requiring more performance than M0/M0+ can deliver. The EFM32G family is positioned by Silicon Labs as one of the lowest-energy Cortex-M3 product lines on the market. Key features include 53 digital I/O pins, 3 x 16-bit timers, AES hardware encryption, autonomous peripherals that operate in sleep modes, ultra-fast wake-up from sleep, an integrated LESENSE / low-energy sensor interface block, and on-chip analog such as ADC and comparator blocks. The Gecko series targets battery-powered systems with typical Stop current of 0.6 uA and Run current of 180 uA/MHz per the EFM32G datasheet. The device operates across the industrial -40C to +85C range. Architecturally, the part uses a Cortex-M3 core with a peripheral reflex system (PRS) that lets peripherals signal each other without CPU intervention - a key energy saver. Flash and RAM are accessed through the AHB-Lite bus, and low-energy peripherals are placed on a separate APB bus so they can run while the CPU sleeps. Typical applications include battery-powered IoT sensors, wearable health monitors, smart metering, wireless sensor nodes paired with sub-GHz or BLE companions, and industrial HMI / alarm panels. The integrated AES block is suitable for encrypted firmware update and secure authentication. When designing with this device, plan the decoupling network carefully: place 100 nF and 1 uF capacitors as close as possible to each VDD pin pair, and follow the EFM32G hardware design guide for the 32 kHz crystal layout to avoid extra current draw from a high-ESR load. A JTAG or SWD header is required for programming - the on-chip debug interface is supported by Simplicity Studio and the J-Link toolchain.

Permintaan RFG Kontak
EFM32G232F128G-E-QFP64R - 32MHz Cortex-M3 MCU 128KB Flash | Silicon Labs
EFM32G232F128G-E-QFP64R

EFM32G232F128G-E-QFP64R - 32MHz Cortex-M3 MCU 128KB Flash | Silicon Labs

The Silicon Labs EFM32G232F128G-E-QFP64R is a 32-bit ARM Cortex-M3 based Gecko microcontroller IC integrating 128KB Flash, 16KB RAM, AES encryption hardware, and an autonomous peripheral set, housed in a 64-pin TQFP (10x10 mm) package. It operates from a 1.98V to 3.8V supply at up to 32MHz core clock and offers 53 general-purpose I/O pins, the Low Energy Sensor Interface (LESENSE), and the peripheral reflex system that lets timers, ADCs, and GPIOs react without CPU wakeup. A microcontroller (MCU) is an integrated circuit that combines a processor core, program and data memory, peripherals, and interrupt logic on a single chip. The Cortex-M3 family is a 32-bit RISC core designed for embedded applications, balancing deterministic interrupt latency, Thumb-2 instruction efficiency, and a tightly integrated NVIC. The EFM32G "Gecko" family belongs to the broader ARM Cortex-M MCU ecosystem within Silicon Labs' energy-friendly portfolio, positioning it between 8-bit MCUs and higher-end Cortex-M4 application processors. Key features of the EFM32G232F128G-E-QFP64R include 0.6 uA Stop mode current (RTC running), 180 uA/MHz Run mode current, hardware AES-128 encryption accelerator, 12-bit ADC, 8-channel DMA, integrated LCD controller, and 2x analog comparator plus 3x operational amplifier (op-amp) blocks. This peripheral integration reduces external bill-of-materials for sensor and metering designs, while the autonomous LESENSE block can scan capacitive or inductive sensors in deep sleep. The architecture centers on a low-leakage CMOS process and energy-modes-aware clock gating, allowing the device to enter EM2/EM3 deep-sleep states while still triggering wakeup from GPIO, RTC, or LESENSE events. The peripheral reflex system (PRS) routes peripheral events over dedicated fabric channels, offloading routine signal routing from the CPU and enabling sub-microsecond response without leaving sleep. Typical applications include battery-powered IoT sensor nodes, smart HVAC thermostats, water/gas utility metering, wireless sensor hubs front-ending sub-GHz radios, wearable health patches, and industrial asset tracking tags. The on-chip AES-128 block and 128KB Flash also suit retrofit devices that need authenticated firmware updates over BLE/Zigbee companion ICs. When designing with the EFM32G232F128G-E-QFP64R, budget decoupling capacitors close to every VDD/VDD_x pair, route the 32kHz crystal traces symmetrically, and leverage the EFM32 CMSIS-Pack and Simplicity Studio for peripheral configuration to avoid hidden power draw from misconfigured GPIO retention modes. This page synthesizes distributor stock, parametric cross-references, and design guidance beyond the manufacturer datasheet, helping engineers select drop-in same-package variants and understand where this Gecko MCU fits within the wider ARM Cortex-M3 landscape.

Permintaan RFG Kontak
EFM32G232F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G232F32-QFP64

EFM32G232F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G232F32-QFP64 is an ARM Cortex-M3 32-bit microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 53 digital I/O pins in a 64-TQFP package. It combines conventional embedded processing with a low-power Gecko platform designed for energy-sensitive systems. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, peripherals, and I/O into one device. The ARM Cortex-M3 belongs to the embedded microcontroller hierarchy, while the EFM32G family adds low-power design techniques, fast wake-up behavior, and energy-saving modes. This makes the device suitable when a design needs more control capability than a simple fixed-function controller without adopting a more complex high-performance processor. The EFM32G232F32-QFP64 provides 32 kB Flash for firmware and 8 kB RAM for working data. Its 53 digital I/O pins support external sensors, indicators, switches, communications interfaces, and control signals. Three 16-bit timers are included for periodic events, timing, input capture, output compare, or other timer-based functions. The 32 MHz Cortex-M3 core provides a balance of processing speed and low-power operation for embedded control. The verified manufacturer result specifically identifies the device as an ARM Cortex-M3 based MCU with speeds up to 32 MHz and highlights its low-power platform, fast wake-up times, energy-saving modes, 32 kB Flash, 8 kB RAM, 53 digital I/O pins, and three 16-bit timers. Exact supply voltage, peripheral details, package dimensions, temperature limits, memory organization, and electrical characteristics were not included in the supplied source snippets and therefore remain marked where data is needed. Typical uses include low-power sensor nodes, industrial control products, building automation modules, connected measurement equipment, small motor-control systems, and portable embedded instruments. The 64-TQFP package exposes more I/O than smaller packages and can simplify board-level routing when a design requires several external connections. Compared with a low-pin-count MCU, the EFM32G232F32-QFP64 offers additional I/O flexibility while retaining a compact surface-mount form factor. Designers should verify the complete manufacturer datasheet before layout, firmware development, or production release. Pay particular attention to power sequencing, decoupling, exposed-pin requirements, clock configuration, programming method, peripheral multiplexing, and the exact meanings of all 64 package pins. The supplied data supports the core, memory, speed, I/O, timer, package, and low-power claims above but does not provide a complete electrical table. This page consolidates the verified manufacturer and distributor search results, records unavailable technical fields transparently, and distinguishes the target MCU from package-only or functionally similar alternatives. The primary sourcing path is the Silicon Labs product page, supplemented by distributor records for procurement and additional datasheet discovery.

Permintaan RFG Kontak
EFM32G232F64-QFP64 - 32MHz Cortex-M3 64KB Flash MCU | Silicon Labs
EFM32G232F64-QFP64

EFM32G232F64-QFP64 - 32MHz Cortex-M3 64KB Flash MCU | Silicon Labs

The Silicon Labs EFM32G232F64-QFP64 is an ARM Cortex-M3 based 32-bit microcontroller (MCU) running up to 32 MHz, with 64 kB Flash (64K x 8), 16 kB RAM and 53 digital I/O pins, supplied in a 64-TQFP (10x10 mm) package operating from 1.98 V to 3.8 V. It belongs to the EFM32 Gecko family, a low-power 32-bit MCU platform built around energy-conscious techniques, fast wake-up times and multiple energy-saving modes. An MCU (microcontroller) is a single integrated circuit containing a CPU core, program memory, data memory and peripherals. In the taxonomy a microcontroller is a type of integrated circuit and semiconductor, and within that group it sits beside memory ICs, interface ICs, ADC/DAC and clock & timing devices. The Gecko family specifically targets energy-sensitive embedded systems where average current draw, not just peak performance, determines battery life. Key features of this device include a 32 MHz ARM Cortex-M3 core with integrated sleep and stop modes, 64 kB of flash for firmware and 16 kB of SRAM for working memory, three 16-bit timers, and hardware AES support as noted in the Mouser listing for this part number. A wide 1.98 V to 3.8 V supply range makes the part usable across 2.5 V and 3.3 V system rails, and the 64-TQFP 10x10 mm footprint keeps the board area small while exposing 53 GPIO for sensors, actuators and communications. Technically the part belongs to the Gecko series, whose energy-saving modes and fast wake-up behaviour are the differentiating architectural features versus generic Cortex-M3 devices. Because the device is available in a 64-pin TQFP, designers get both fine-grained pin multiplexing and a package that is straightforward for automated assembly, pick-and-place and visual inspection, unlike fine-pitch QFN or BGA options. Typical applications include low-power sensor nodes and IoT end devices, industrial monitoring and control modules, building and energy metering equipment, portable and wearable accessories, and USB-connected peripheral controllers where the 53 available I/O pins allow several peripherals to share one package. A key design consideration is that the flash capacity and RAM size define how much application code and data buffering fit on the die; designs that need large buffers should consider the 128 kB and 256 kB members of the Gecko family instead of this 64 kB variant. This page synthesizes distributor pricing, verified drop-in alternatives, pin-level guidance and practical design notes that are not found together in the manufacturer datasheet, helping engineers shorten BOM and layout decisions for EFM32G232F64-QFP64.

Permintaan RFG Kontak
EFM32G280F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G280F32-QFP100

EFM32G280F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G280F32-QFP100 is a 32-bit ARM Cortex-M3 Gecko microcontroller rated up to 32 MHz, with 32 kB of flash memory, 8 kB of RAM, and 86 digital I/O pins in a 100-pin LQFP package measuring 14 x 14 mm. The device combines conventional embedded-control processing with energy-saving modes and fast wake-up behavior for energy-conscious systems. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, peripherals, and I/O into one compact component. The EFM32G280 belongs to the EFM32 Gecko family, a hierarchy of ARM Cortex-M3 microcontrollers designed for embedded control, low-power sensing, communications, and industrial applications. Its architecture provides general-purpose computation alongside dedicated timers and energy-management functions. The EFM32G280F32-QFP100 includes 3 x 16-bit timers, 86 digital I/O pins, and operation up to 32 MHz. Its 32 kB flash stores firmware, while 8 kB RAM supports working data, stack space, and peripheral buffers. The 100-pin LQFP provides enough connections for external sensing interfaces, communications, control outputs, and debug or programming access without relying on a very small package. The Cortex-M3 processor supports a 32-bit instruction set and an efficient embedded-control architecture. Silicon Labs positions the Gecko platform around low-energy operation, rapid transitions from energy-saving states, and multiple sleep-related operating modes. These characteristics help reduce the average energy consumed by systems that spend much of their time monitoring inputs rather than executing continuous computation. Typical applications include low-power sensor nodes, connected industrial equipment, environmental monitoring, compact control systems, and energy-harvesting products. The combination of 86 digital I/O pins and three 16-bit timers is particularly useful when a design needs multiple discrete inputs, timing channels, motor or actuator control, and communication peripherals on a single controller. PCB implementation should preserve the 100-pin LQFP footprint, provide clean grounding, and route sensitive signal paths away from switching nodes. Designers should also budget flash and RAM for the complete firmware, interrupt handlers, and application state rather than relying only on nominal application-code size. Confirm the complete pin assignments and peripheral multiplexing in the manufacturer pinout table before final routing. This page consolidates the manufacturer specifications, package information, sourcing guidance, and design considerations needed to evaluate the EFM32G280F32-QFP100. It also identifies the constraints involved in finding a genuine same-footprint replacement, rather than presenting devices with incompatible memory sizes or peripheral configurations as drop-in choices.

Permintaan RFG Kontak
EFM32G280F64-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G280F64-QFP100

EFM32G280F64-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G280F64-QFP100 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB of flash memory, 16 kB of RAM, and 86 digital I/O pins in a 100-LQFP package. It also provides three 16-bit timers and operates from a 3 V supply, making it suitable for compact embedded systems requiring substantial I/O and low-power operation. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripheral interfaces, and I/O into one device. The EFM32G280F64-QFP100 belongs to the 32-bit embedded MCU hierarchy and uses the ARM Cortex-M3 architecture. It is designed for applications where local control, communication, sensing, and actuator control must be handled by a compact embedded platform. The device combines a 32 MHz ARM Cortex-M3 processor with 64 kB of flash and 16 kB of RAM. Its 86 digital I/O pins provide broad connectivity for sensors, displays, communications, and control signals. Three 16-bit timers support periodic timing, pulse measurement, and timing-intensive control functions. The listed AES capability adds hardware support for applications requiring encrypted data handling. Silicon Labs describes the Gecko platform around low-energy techniques, fast wake-up behavior, and energy-saving operating modes. These characteristics are particularly useful in battery-powered or intermittently powered equipment. The external oscillator configuration listed for this family supports designs where precise timing derives from an external clock source rather than an internal oscillator alone. Typical uses include industrial monitoring, energy-sensitive sensor nodes, building automation, connected equipment, and compact embedded controllers. The high pin count can reduce the need for I/O expanders in designs that connect multiple discrete sensors, status indicators, communications lines, and actuator outputs to one controller. PCB implementation requires attention to the 100-LQFP footprint, power routing, decoupling, clock stability, programming access, and exposed peripheral limits. Place the required decoupling capacitors close to the supply pins, route high-current returns through a stable ground plane, and follow the manufacturer's pin-description table when assigning tracks. Confirm boot, programming, and reset behavior in hardware before releasing the layout. This product page consolidates the core specifications, practical use cases, package information, and sourcing options for the EFM32G280F64-QFP100. It also provides a structured comparison with closely related Silicon Labs EFM32 devices to help engineers distinguish ordering codes, memory capacity, and peripheral differences without overlooking PCB compatibility.

Permintaan RFG Kontak
EFM32G290F128-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G290F128-BGA112

EFM32G290F128-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G290F128-BGA112 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 128 kB flash memory, 16 kB RAM, and 90 digital I/O pins, housed in a 112-BGA package measuring 10 x 10 mm. The device also integrates eight 12-bit ADC channels, two 12-bit DAC channels, and AES hardware security for connected and energy-conscious embedded systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The EFM32G290 belongs to the EFM32 Gecko family and the broader embedded-controller hierarchy: Cortex-M3 processor core, 32-bit microcontroller, embedded processor, and semiconductor. Its combination of 128 kB flash, 16 kB RAM, and extensive mixed-signal peripherals makes it suitable for compact control systems that require local processing without a separate external processor. The EFM32G290F128-BGA112 runs at up to 32 MHz and provides 90 digital I/O pins, giving a high pin count for a 10 x 10 mm BGA device. Three 16-bit timers support precise timing, motor control, and periodic sensing tasks. Eight 12-bit ADC channels and two 12-bit DAC channels provide integrated analog measurement and signal generation, reducing the need for external converters in many designs. Integrated AES hardware accelerates cryptographic operations for data protection and authenticated communication. Its low-power architecture is central to the Gecko design. Energy-saving modes, fast wake-up behavior, and low-energy techniques allow the processor to remain responsive while reducing consumption during idle periods. This is particularly useful in battery-operated equipment where the duty cycle alternates between brief processing intervals and long standby periods. The combination of a 32 MHz Cortex-M3 core and dedicated sleep behavior supports responsive control without requiring continuous high-frequency operation. Typical applications include connected sensor nodes, industrial condition-monitoring equipment, compact energy meters, building-automation endpoints, wearable accessories, and embedded gateways. The 90 available digital I/O pins can support displays, buttons, communication interfaces, status indicators, and external sensors, while the ADC and DAC channels support analog front ends. The integrated AES hardware can protect firmware-related secrets, configuration data, or communication payloads when an application requires encryption. For PCB design, use the manufacturer datasheet and application note AN0002, EFM32 Hardware Design Considerations, to assign BGA pads, route power and ground, manage decoupling, and verify exposed-pad and thermal-via requirements. Because this package has 112 fine-pitch BGA lands, inspection and assembly depend on suitable PCB density, pad geometry, solder-paste control, and reflow profiling. This product page combines device specifications, package guidance, application fit, and same-package replacement context to help engineers evaluate the EFM32G290F128-BGA112 before committing a new design. The comparison focuses on documented memory, speed, analog resources, security features, and package compatibility rather than treating devices with different memory configurations as interchangeable without review.

Permintaan RFG Kontak
EFM32G290F32-BGA112 - 32MHz ARM Cortex-M3 MCU | Silicon Labs
EFM32G290F32-BGA112

EFM32G290F32-BGA112 - 32MHz ARM Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G290F32-BGA112 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 32 kB Flash, 8 kB RAM, 90 digital I/O pins, and three 16-bit timers in a 112-pin BGA package. The device combines conventional microcontroller processing with energy-saving modes and fast wake-up behavior for power-conscious embedded systems. A microcontroller is a semiconductor that integrates a processor core, programmable memory, peripheral interfaces, and I/O into one compact device. The EFM32G290 belongs to the Gecko family of 32-bit microcontrollers, where the ARM Cortex-M3 core sits within a broader hierarchy of embedded processor, microcontroller, and semiconductor products. Its role is to execute firmware and manage sensors, communications, actuators, and user interfaces while controlling energy use in battery-powered or intermittently powered equipment. Key device characteristics include a maximum CPU frequency of 32 MHz, 32 kB of Flash memory, and 8 kB of RAM. The manufacturer identifies 90 digital I/O pins and three 16-bit timers, providing resources for parallel digital signals, timing, counters, and periodic control functions. The Cortex-M3 architecture also supports efficient interrupt-driven firmware, while the Gecko low-power platform is intended to extend operating time in energy-sensitive applications. The 112-pin BGA package exposes a comparatively large pin count for a compact embedded design, making it suitable for systems requiring extensive I/O connectivity. Its 32-bit architecture provides greater addressing and computation capability than an 8-bit controller while retaining the deterministic, event-driven operation expected from embedded processors. Exact peripheral, supply, timing, and environmental limits should be confirmed against the manufacturer documentation before schematic release. Typical uses include connected sensor nodes, industrial monitoring equipment, building-control endpoints, compact consumer devices, and low-power instrumentation. The combination of fast wake-up capability, energy-saving modes, and three timers supports designs that periodically sample data, update a display or network link, and return to a reduced-energy state between events. These characteristics also make the MCU suitable for battery-operated accessories where predictable standby behavior is important. Designers should treat the BGA layout as a manufacturing-sensitive assembly feature, use the manufacturer land pattern and pin-assignment tables, and confirm the exact package dimensions and ball map before PCB release. Firmware development should use the documented EFM32 peripheral libraries and startup support for the Cortex-M3 core, and production designs should include the required decoupling, programming access, clock configuration, and brownout behavior. This page combines the manufacturer specifications with practical replacement, package, application, and design guidance. It helps engineers compare the EFM32G290F32-BGA112 with related Gecko devices, plan low-power architectures, and identify the documentation needed for a reliable 112-ball PCB design and firmware bring-up.

Permintaan RFG Kontak
EFM32G290F64-BGA112 - 32MHz Cortex-M3 64KB MCU | Silicon Labs
EFM32G290F64-BGA112

EFM32G290F64-BGA112 - 32MHz Cortex-M3 64KB MCU | Silicon Labs

Silicon Labs EFM32G290F64-BGA112 is a 32-bit ARM Cortex-M3 Gecko microcontroller operating up to 32 MHz, with 64 KB of Flash memory, 16 KB of RAM, 90 digital I/O pins, and three 16-bit timers. The device is supplied in a 112-pin BGA package measuring 10 mm by 10 mm. Its low-power architecture, fast wake-up capability, and energy-saving modes target energy-conscious embedded systems. A microcontroller is a programmable embedded-control component that integrates a processor core, memory, peripherals, and I/O into one semiconductor device. The EFM32G290F64-BGA112 belongs to the EFM32 Gecko family, where the Gecko architecture combines an ARM Cortex-M3 processor with Silicon Labs low-power peripherals. This hierarchy places it within 32-bit microcontrollers, embedded processors, and energy-efficient semiconductor control systems. Core resources include 64 KB of Flash for firmware and 16 KB of RAM for working data. The device provides 90 digital I/O pins and three 16-bit timers, enabling simultaneous peripheral functions in space-constrained designs. Its operating supply range is 1.98 V to 3.8 V. Silicon Labs emphasizes low power consumption, with the EFM32G family consuming as little as 0.6 microampere in Stop mode and 180 microamperes per megahertz in Run mode. The ARM Cortex-M3 core provides a 32-bit processing architecture while retaining a compact embedded footprint. Silicon Labs EFM32 devices also feature autonomous peripherals, high analog integration, and energy-management modes that can reduce activity when the processor is not required to run continuously. These characteristics make the MCU suitable for designs in which response time and standby current both matter. Typical applications include low-power sensor nodes, connected industrial equipment, compact consumer devices, and embedded control modules. The 90-pin interface count supports board-level integration involving communications, timers, analog inputs, and digital control signals. The small 10 mm by 10 mm BGA also supports compact assemblies when careful PCB routing, thermal design, and assembly process control are applied. Designers should evaluate low-power mode behavior, wake-up requirements, pin multiplexing, and BGA assembly constraints before finalizing the PCB. The manufacturer datasheet should be used to assign every ball and peripheral function. Power routing and decoupling require a stable 1.98 V to 3.8 V supply environment, while firmware should use the documented sleep and Stop-mode entry procedures to achieve the intended energy savings. This product overview combines the device architecture, memory resources, package information, low-power characteristics, application guidance, and engineering considerations needed to plan an EFM32G290F64-BGA112-based design. It also provides same-package alternatives, specification comparisons, and practical implementation guidance to support component selection and board development.

Permintaan RFG Kontak
EFM32G30F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs
EFM32G30F128-QFN64

EFM32G30F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs

The Silicon Labs EFM32G30F128-QFN64 is a 32-bit ARM Cortex-M3 Gecko microcontroller with a 32 MHz operating frequency, 128 KB of embedded flash memory, and 16 KB of RAM, supplied in a compact 64-QFN 9 x 9 mm package. It operates from a 1.98 V to 3.8 V supply and is designed for low-power embedded systems requiring efficient processing, analog integration, and autonomous peripheral operation. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The EFM32G30F128-QFN64 belongs to the Gecko family of 32-bit ARM Cortex-M3 microcontrollers, which sit within the hierarchy of embedded processors, microcontrollers, and semiconductor control devices. Its ARM Cortex-M3 core provides a 32-bit instruction set while the EFM32 peripheral architecture allows many hardware functions to operate with limited CPU involvement. The verified device data identifies a maximum clock frequency of 32 MHz, 128 KB of flash organized as 128K x 8, and 16 KB of SRAM. Silicon Labs specifies a 1.98 V to 3.8 V operating supply range and a 64-QFN package measuring 9 x 9 mm. The family datasheet also reports low power consumption, including as little as 0.6 uA in Stop mode and 180 uA/MHz in Run mode, making the device suitable for battery-powered and energy-conscious products. The Gecko architecture integrates high-speed analog and digital peripherals with the Cortex-M3 core. Product Revision E documentation identifies pin-compatible replacements for earlier EFM32G revision devices. However, firmware, peripheral configuration, and electrical behavior must still be checked against the specific part-number suffix before treating a related revision as a production substitute. A complete exposed-pad thermal design is essential because heat removal depends on the PCB copper area and thermal via arrangement. Typical uses include industrial sensing and control nodes, compact environmental monitors, battery-powered IoT endpoints, wearable accessories, and connected measurement instruments. The small 9 x 9 mm QFN footprint supports space-constrained designs where a larger quad flat package would be undesirable. The 128 KB flash capacity provides room for application firmware, protocol stacks, and boot code, while the 16 KB RAM supports task working memory and moderate buffering. Designers should follow the manufacturer's recommended power, decoupling, and exposed-pad land-pattern requirements. A high-quality local ground plane and short return paths help analog and digital sections remain stable under switching loads. Confirm the exact operating temperature grade, peripheral mix, and pin multiplexing for the ordered MPN before layout release because the verified distributor data does not specify those complete values. This page consolidates verified manufacturer specifications, distributor availability information, pin-compatible same-family options, package constraints, and practical engineering guidance. The comparison material also distinguishes genuine drop-in choices from related devices that require firmware or board-level qualification.

Permintaan RFG Kontak
EFM32G800F128G-E-D1I - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G800F128G-E-D1I

EFM32G800F128G-E-D1I - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G800F128G-E-D1I is a 32-bit ARM Cortex-M3 Gecko microcontroller with a 32 MHz operating frequency, 128 KB of flash memory, and a 1.98 V to 3.8 V supply-voltage range. The device is supplied as an unpackaged die for module, wafer-level, and embedded manufacturing applications rather than as a conventional leaded or surface-mount component. A microcontroller is an integrated circuit that combines a processor core, program memory, data memory, and peripherals such as timers, serial interfaces, analog blocks, and interrupt controllers. The EFM32G family belongs to the broader embedded-control hierarchy of microcontroller ICs and uses the ARM Cortex-M3 processor architecture for compact, real-time control systems. Key characteristics include a 32-bit single-core Cortex-M3 processor, 128 KB of flash organized as 128K x 8, and operation from a 1.98 V to 3.8 V supply. According to the Silicon Labs EFM32G datasheet, the Gecko family consumes as little as 0.6 uA in Stop mode and 180 uA/MHz in Run mode, supporting applications where standby energy use is a primary design constraint. The EFM32G architecture combines autonomous peripherals with substantial analog and digital integration. Peripheral operation can continue with reduced processor intervention, helping deterministic control systems manage time-critical tasks. The Cortex-M3 core also supports efficient exception handling, while the integrated analog and communication resources reduce the component count required for sensor acquisition, industrial monitoring, and connected embedded products. Typical uses include low-power sensor nodes, battery-operated measurement instruments, industrial condition-monitoring equipment, compact control modules, and energy-harvesting products. The 128 KB flash capacity is suitable for moderate firmware images containing drivers, protocol stacks, application logic, and update services without requiring external program memory. The die package requires a package-specific assembly process, so the pin assignment, bonding plan, and exposed-pad requirements must be confirmed before layout. Use the EFM32G datasheet and EFM32G reference manual for die markings, pad locations, programming procedures, peripheral details, and production test requirements. This page consolidates the verified device identity, electrical envelope, power characteristics, die-package considerations, commercial ordering information, and design guidance into a single engineering reference for engineers evaluating the EFM32G800F128G-E-D1I for an embedded module or wafer-level design.

Permintaan RFG Kontak
EFM32G840F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs
EFM32G840F128-QFN64

EFM32G840F128-QFN64 - 32MHz Cortex-M3 128KB MCU | Silicon Labs

Silicon Labs EFM32G840F128-QFN64 is a 32-bit ARM Cortex-M3 Gecko microcontroller rated up to 32 MHz, with 128 KB of Flash memory, 16 KB of RAM, and 56 digital I/O pins, packaged in a 64-QFN 9 x 9 mm package. The device operates from a 1.85 V to 3.8 V supply and supports an industrial temperature range of -40 °C to 85 °C. Three 16-bit timers and a low-energy platform make it suitable for embedded control, sensing, communications, and portable systems. A microcontroller is a programmable semiconductor that integrates a CPU core, nonvolatile program memory, volatile data memory, peripherals, and I/O into one device. The EFM32G840F128-QFN64 belongs to the EFM32 Gecko family, where the hierarchy is ARM Cortex-M3 processor, 32-bit MCU, embedded microcontroller, and semiconductor. It executes firmware from its 128 KB Flash memory while using 16 KB of RAM for working data and stack operations. Key features include operation up to 32 MHz, 56 digital I/O pins, and three 16-bit timer/counter peripherals. The 64-QFN package supports compact surface-mount layouts while its exposed pad provides a direct thermal path to the PCB. Low-energy operating techniques, fast wake-up behavior, and energy-saving modes are central to the Gecko architecture, making the MCU appropriate for systems that spend substantial time asleep. The ARM Cortex-M3 core provides a 32-bit RISC instruction set and an integrated interrupt architecture for responsive control applications. Flash memory stores the application firmware, while RAM supports the main loop, interrupt service routines, communication buffers, and sensor-processing state. The three 16-bit timers support periodic events, timing, input capture, or output compare functions, depending on the configured peripheral mode and the complete device documentation. Typical uses include industrial sensor nodes, low-energy wireless accessories, building-control endpoints, compact instrumentation, portable equipment, and embedded monitoring systems. Designers can select it where 128 KB of program storage, 16 KB of RAM, 56 GPIO, and a 32 MHz processing rate provide an appropriate balance between capability, board area, and energy-conscious operation. The principal design considerations are power-rail integrity, decoupling, exposed-pad thermal management, and correct firmware support for the QFN footprint. Place the required bypass capacitors close to their supply pins, provide a low-impedance ground plane, and follow the manufacturer's footprint and land-pattern guidance. Confirm peripheral availability, interrupt behavior, and low-power mode requirements against the manufacturer documentation before finalizing the design. This page combines the manufacturer's device specifications, package details, family alternatives, and practical implementation guidance to support component selection, PCB planning, firmware preparation, and sourcing decisions. The comparison tables and application sections emphasize where memory capacity, package compatibility, timer resources, and low-power operation matter in embedded product design.

Permintaan RFG Kontak
EFM32G840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G840F32-QFN64

EFM32G840F32-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G840F32-QFN64 is an ARM Cortex-M3 32-bit microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 56 digital I/O pins in a 64-QFN package with an exposed pad. It is designed for energy-sensitive embedded systems. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, digital interfaces, timers, analog peripherals, and power-management functions. The EFM32G840F32-QFN64 belongs to the EFM32 Gecko family and combines an ARM Cortex-M3 core with low-power operating techniques, short wake-up behavior, and energy-saving modes for battery-operated and portable equipment. Verified product information identifies 32 kB Flash, 8 kB RAM, 56 digital I/O pins, three 16-bit timers, and operation up to 32 MHz. The device is intended for applications that require compact embedded control, efficient peripheral integration, and low-energy operation. Its 64-QFN package provides a high pin count for digital connectivity in a relatively small surface-mount footprint. The EFM32G840F32-QFN64 is suitable for sensor nodes, industrial monitoring, building automation, portable measurement equipment, connected embedded products, and low-power control systems. The exposed pad supports thermal management when the device dissipates power during operation; PCB copper and thermal design should follow the manufacturer package guidance. When designing around this MCU, verify the exact pin multiplexing, supply requirements, peripheral availability, and package-specific exposed-pad requirements against the manufacturer datasheet. Do not substitute a different package or pin count without reviewing the complete pinout and board footprint. This page consolidates verified manufacturer and distributor information, datasheet access, application context, and replacement-screening guidance. It is intended to help engineers identify the correct EFM32G840F32-QFN64 for embedded designs rather than treating similar ARM MCUs as automatically interchangeable.

Permintaan RFG Kontak
EFM32G840F64-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G840F64-QFN64

EFM32G840F64-QFN64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G840F64-QFN64 is an ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB Flash, 16 kB RAM, and 56 digital I/O pins in a 64-QFN package. Designed for energy-sensitive embedded systems, it combines a low-power Gecko platform, fast wake-up capability, and energy-saving modes for responsive designs with constrained power budgets. A microcontroller is a programmable semiconductor that integrates a processor core, memory, I/O, timers, and communication peripherals on one integrated circuit. Within the product hierarchy, the EFM32G840F64-QFN64 is a 32-bit ARM Cortex-M3 MCU in the EFM32 Gecko family. It executes embedded control logic while providing local digital interfaces, analog functions, and low-power operating modes for connected products. The verified device features include a 32 MHz maximum CPU speed, 64 kB Flash, 16 kB RAM, 56 digital I/O pins, and three 16-bit timers. Distributor data also identifies a 64-QFN package with a 9 mm by 9 mm body and an exposed pad. The package supports surface-mount assembly, while the exposed pad provides the primary thermal connection on the PCB. The Cortex-M3 architecture gives the MCU a 32-bit processing interface suitable for control loops, human-interface logic, communications, and general embedded tasks. The Gecko low-power platform is particularly relevant in battery-operated equipment because the device combines conventional processing with energy-saving modes. Designers should use the Silicon Labs documentation to configure wake behavior, clocks, peripherals, and current-consumption targets for the exact product configuration. Typical uses include industrial sensor nodes, connected meters, portable medical accessories, smart-building controls, compact consumer devices, and low-energy IoT equipment. Its 56 digital I/O pins can support buttons, displays, indicators, and external interface signals, while the three 16-bit timers are useful for timing, pulse generation, and periodic control tasks. A critical design consideration is decoupling and exposed-pad layout. Place the required bypass capacitors close to the supply pins and connect the exposed thermal pad according to the manufacturer's package guidance. Validate the power rails, boot configuration, peripheral pin mapping, and low-power behavior on hardware before production. This page combines verified manufacturer and distributor facts with engineering-focused selection, comparison, sourcing, and design guidance. It is intended to help engineers identify the correct MCU, verify package assumptions, and assess migration options without relying on unverified electrical or lifecycle assumptions.

Permintaan RFG Kontak
EFM32G842F128-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G842F128-QFP64

EFM32G842F128-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G842F128-QFP64 is a 32-bit ARM Cortex-M3 microcontroller rated up to 32 MHz, with 128 kB of Flash memory, 16 kB of RAM, and 53 digital I/O pins in a 64-TQFP surface-mount package measuring 10 mm by 10 mm. The device is designed for energy-sensitive embedded systems that require responsive processing, low-power operation, and extensive integrated peripherals. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor that combines a standardized instruction set with peripherals integrated onto one semiconductor die. Within the product hierarchy, the EFM32G842F128-QFP64 is an MCU, a semiconductor, and a member of the Silicon Labs EFM32 Gecko family. Its low-energy platform supports fast wake-up behavior and energy-saving modes for systems that spend substantial time sleeping. The device includes 128 kB of Flash for firmware and 16 kB of RAM for working data. Three 16-bit timers provide timing resources for periodic control, input capture, output compare, and other time-based functions. Its 53 digital I/O pins support connections to sensors, displays, communication peripherals, and control logic, while the 32 MHz Cortex-M3 core provides useful processing headroom for protocol handling and supervisory tasks. The EFM32G platform emphasizes integration and energy efficiency. According to the Silicon Labs EFM32G datasheet, Gecko devices can consume as little as 0.6 microamps in Stop mode and approximately 180 microamps per MHz in Run mode. These figures make the family relevant to battery-powered instrumentation, portable measurement equipment, industrial controls, and connected sensor nodes where average energy consumption matters as much as peak processing speed. Typical applications include low-power sensor nodes, industrial meters, portable health and wellness devices, connected building equipment, and compact consumer products. The 64-TQFP package exposes more I/O than smaller packages and remains practical for automated assembly. Designers should implement the manufacturer's recommended decoupling, oscillator, reset, and programming connections before deploying the MCU in production. The main design trade-off is Flash capacity versus alternatives with less memory. Select the 128 kB version when application firmware, boot code, data tables, and future updates require ample program storage. The 64-TQFP outline also demands more PCB area than a 32-pin or 48-pin package, but it reduces the need for an external I/O expander and supports more peripheral connections. This product record combines the manufacturer's operating characteristics with practical application guidance, package-aware comparison information, and direct sourcing through the Request a Quote form on this page. It is designed to help engineers evaluate memory, I/O capacity, low-power behavior, and footprint before committing the EFM32G842F128-QFP64 to a new embedded design.

Permintaan RFG Kontak
EFM32G842F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G842F32-QFP64

EFM32G842F32-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G842F32-QFP64 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 32 kB of Flash memory, 8 kB of RAM, and 53 digital I/O pins in a 64-pin TQFP package. Its combination of low-power design, fast wake-up capability, and energy-saving operating modes targets embedded systems where battery life and deterministic control are important. A microcontroller is a programmable system-on-chip that integrates a CPU, memory, peripherals, and I/O into one package. The EFM32G842 belongs to the EFM32 Gecko family, which combines an ARM Cortex-M3 processor with energy-management hardware for low-power embedded control. This places it in the hierarchy of embedded microcontroller, 32-bit MCU, ARM Cortex-M3 processor, and semiconductor device. The device provides 32 kB Flash for program storage and 8 kB RAM for working data. The verified manufacturer information also identifies three 16-bit timers and 53 digital I/O pins. The 32 MHz CPU supports responsive control, while low-energy modes and fast wake-up behavior can reduce inactive-system power. Its 2.5 V and 3.3 V supply references are identified in the verified distributor material. The EFM32G842F32-QFP64 is suited to energy-sensitive embedded products, including sensor nodes, industrial monitoring equipment, portable instrumentation, and connected low-power systems. Its timer resources can support periodic measurement, motor or actuator timing, and control-loop tasks. The digital I/O count provides flexibility for buttons, displays, sensors, relays, and communications peripherals, subject to the device's electrical and multiplexing limitations. For PCB design, preserve the exact 64-pin TQFP footprint and verify the complete manufacturer pin assignment before routing. Pay particular attention to supply decoupling, ground-return paths, exposed thermal behavior, and any pins assigned to debug, programming, reset, or alternate functions. Firmware should use the Silicon Labs device support configuration for the exact MPN. This product data combines the verified Silicon Labs device description, distributor specifications, package information, lifecycle-related source material, and application-oriented guidance. It is intended to support initial design review, sourcing, and comparison; final production decisions should be checked against the latest manufacturer datasheet and authorized distribution records. This page synthesizes the supplied manufacturer and distributor information with practical selection context. Because no verified price, detailed timing specification, pin table, or approved cross-brand substitute was supplied, those fields are marked as unavailable rather than inferred.

Permintaan RFG Kontak
EFM32G842F64-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G842F64-QFP64

EFM32G842F64-QFP64 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G842F64-QFP64 is a 32-bit ARM Cortex-M3 microcontroller operating up to 32 MHz, with 64 kB of Flash memory and 16 kB of RAM in a 64-TQFP 10 mm × 10 mm package. The device provides 53 digital I/O pins and three 16-bit timers, combining general-purpose embedded control with low-power operation for energy-sensitive equipment. A microcontroller is a compact integrated circuit containing a processor core, memory, peripherals, and I/O. The EFM32G842 belongs to the EFM32 Gecko family and uses the ARM Cortex-M3 RISC core, placing it in the hierarchy MCU → 32-bit microcontroller → embedded processor → semiconductor. Its low-energy architecture, fast wake-up behavior, and energy-saving modes make it suitable for systems that spend substantial time idle or operate from limited power budgets. Verified features include a 32 MHz operating speed, 64 kB Flash, 16 kB RAM, 53 digital I/O pins, and three 16-bit timers. The 1.98 V to 3.8 V supply range supports 2.5 V and 3.3 V system designs. The LCD, AES, and USB-related ecosystem description shown by distributor listings makes the device relevant to human-interface, secure accessory, and connected embedded applications, while the 64-pin package provides a substantial peripheral-routing option for mixed-signal control boards. The Gecko platform emphasizes fast startup and low-energy execution rather than only peak processing speed. This is valuable in portable instruments, battery-powered sensors, industrial controls, and USB peripherals where the average current between activity periods can determine battery life. Firmware should therefore use the device's sleep and wake behavior deliberately rather than treating the 32 MHz CPU frequency as a continuous-power requirement. Typical applications include energy-harvesting sensors, compact industrial controllers, USB-connected human-interface devices, secure embedded accessories, and low-power monitoring systems. The 53 digital I/O pins are useful for status indicators, buttons, relays, displays, and external interface signals, while the timers support periodic sensing, motor timing, or control-loop tasks. PCB design should preserve short, clean return paths around the MCU and decoupling connections. Follow the manufacturer datasheet for the exact pin names, exposed pad requirements, crystal requirements, and decoupling network. Do not assume that another 64-TQFP MCU is interchangeable solely because its package matches; peripheral mapping, voltage tolerance, firmware support, and pin function must be checked before replacement. This page consolidates verified manufacturer and distributor information, distinguishes the target from unverified alternatives, and adds procurement and design guidance that is not normally present in a basic distributor listing.

Permintaan RFG Kontak
EFM32G880F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G880F32-QFP100

EFM32G880F32-QFP100 - 32MHz Cortex-M3 MCU | Silicon Labs

The Silicon Labs EFM32G880F32-QFP100 is a 32-bit ARM Cortex-M3 Gecko microcontroller with a maximum clock speed of 32 MHz, 32 kB of Flash memory, and 8 kB of RAM, packaged in a 100-LQFP 14 mm x 14 mm surface-mount package. It provides 86 digital I/O pins and three 16-bit timers, making it suitable for connected control systems that require substantial peripheral connectivity in a relatively compact package. An ARM Cortex-M3 microcontroller is a 32-bit embedded processor designed for real-time control, sensor handling, communications, and human-interface applications. Within the product hierarchy, the EFM32G880 belongs to the Gecko MCU family and combines a general-purpose processor with low-power operating techniques, fast wake-up behavior, and energy-saving modes for energy-sensitive equipment. The EFM32G880F32-QFP100 integrates 32 kB Flash, 8 kB RAM, 86 digital I/O pins, and three 16-bit timers. Its operating voltage range is 1.98 V to 3.8 V, while its maximum CPU frequency is 32 MHz. The manufacturer identifies the device for applications requiring secure data processing, AES encryption support, and graphics or LCD-oriented functionality, including support for a 4 x 40 LCD. The Gecko low-power architecture is central to the device's value in embedded systems. Low-energy techniques and energy-saving modes allow the MCU to reduce active consumption during idle intervals, while fast wake-up behavior supports responsive event-driven designs. Developers can use the Cortex-M3 instruction set and integrated peripherals to consolidate control, communications, display handling, and data acquisition onto one device rather than distributing those tasks among multiple discrete components. Typical applications include industrial sensor nodes, building automation controllers, portable measurement instruments, medical monitoring equipment, graphical user-interface controllers, and connected energy-management products. The 86 digital I/O pins are especially useful where an application must connect discrete sensors, actuators, buttons, indicators, or external interface devices while preserving a high pin count for direct PCB routing. When laying out a board, assign all 100 package pins by consulting the manufacturer pin-description table and account for the exposed supply, ground, debugging, and peripheral functions shown there. Confirm operating conditions, voltage rails, and peripheral multiplexing against the manufacturer datasheet before finalizing the schematic and footprint. The 100-LQFP package supports a 14 mm x 14 mm land pattern but requires careful assembly planning because of its fine pitch. This page combines manufacturer specifications, sourced product information, application guidance, pin-package considerations, and engineering-focused comparisons to support component selection and PCB planning. It also identifies the limitations of available drop-in alternatives so engineers can distinguish electrically similar replacements from verified, package-compatible choices.

Permintaan RFG Kontak
EFM32G890F32-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G890F32-BGA112

EFM32G890F32-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G890F32-BGA112 is a 32-bit ARM Cortex-M3 Gecko microcontroller operating at up to 32 MHz, with 32 KB of Flash memory, 8 KB of RAM, and 90 digital I/O pins in a 112-BGA package measuring 10 mm by 10 mm. The device is designed around the EFM32G energy-management platform, which combines low-power operation, fast wake-up behavior, and autonomous peripheral activity. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals such as serial interfaces, timers, and analog blocks. Within the product hierarchy, the EFM32G890F32 belongs to the ARM Cortex-M3 microcontroller class, the EFM32 Gecko family, and the broader embedded-control semiconductor category. Its combination of a 32-bit processor and low-power peripherals makes it suitable for battery-operated equipment and other embedded systems that must process data while limiting energy use. The EFM32G890F32-BGA112 provides 32 KB of Flash program memory and 8 KB of SRAM, supporting firmware storage, working memory, and application state. Its listed digital interface resources include 90 I/O pins, three 16-bit timers, EBI/EMI, I2C, IrDA, SPI, SmartCard, and UART/USART connectivity. These interfaces allow the MCU to communicate with sensors, displays, external nonvolatile memory, transceivers, and other embedded peripherals without requiring multiple companion controllers. Silicon Labs describes the EFM32G family as an energy-oriented platform with autonomous peripherals and low current draw in both active and sleep operating states. The family data sheet states that EFM32G devices can consume as little as 0.6 microamps in Stop mode and 180 microamps per megahertz in Run mode. These figures characterize the broader family and should be checked against the exact operating configuration, clock rate, and peripheral activity used in a finished design. Typical uses include industrial sensor nodes, compact wireless-control equipment, battery-powered instruments, building-automation endpoints, wearable accessories, and low-power IoT controllers. In each case, the MCU can execute control logic while using its low-energy modes between external events. The 112-BGA package also supports compact PCB designs, although its fine pitch requires careful assembly planning, inspection access, and multilayer board construction. Design the power rails and decoupling around the 3.3 V-class operating environment described for this device family, and use the pin-description tables in the manufacturer datasheet when assigning the 90 digital I/O pins. Confirm package ball assignments, exposed-pad treatment, supported supply tolerances, and peripheral multiplexing before release because those details are not reproduced in the product listing. This product record combines the exact ordering information, memory configuration, package dimensions, core speed, interface list, and low-power family characteristics with practical considerations for PCB layout, firmware sizing, and sourcing. It also provides same-package alternatives and a parameter-by-parameter comparison so engineers can distinguish flash-capacity changes from true pin-compatible design choices.

Permintaan RFG Kontak
EFM32G890F64-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs
EFM32G890F64-BGA112

EFM32G890F64-BGA112 - 32MHz Cortex-M3 MCU | Silicon Labs

Silicon Labs EFM32G890F64-BGA112 is a 32-bit ARM Cortex-M3 Gecko microcontroller with a 32 MHz operating speed, 64 KB of Flash memory, 16 KB of RAM, and 90 digital I/O pins in a 112-BGA package measuring 10 mm by 10 mm. Its low-power architecture, fast wake-up capability, and energy-saving modes target battery-operated and energy-sensitive embedded systems. A microcontroller, or MCU, integrates a processor core, memory, peripherals, and interfaces into one compact device. The EFM32G890 belongs to the Gecko family of 32-bit embedded processors within Silicon Labs' broader MCU portfolio. MCUs are commonly used for sensing, control, communications, and user-interface tasks where deterministic real-time operation, low standby power, and a compact footprint are more important than a desktop-class processor. The EFM32G890F64-BGA112 combines 64 KB of Flash with 16 KB of SRAM and three 16-bit timers. Its peripheral set includes a 4-by-40 LCD interface and AES hardware, while the 90 digital I/O pins support multiple external devices on a compact assembly. A maximum clock rate of 32 MHz provides useful processing headroom for protocol handling, control loops, and system management without requiring a separate processor. The Cortex-M3 core uses the Arm Thumb instruction set and supports efficient event-driven firmware. Silicon Labs' low-energy techniques include energy-saving modes and fast wake-up behavior, which help battery-operated equipment remain responsive without keeping the core active continuously. These characteristics make the device suitable for sensors, portable instruments, industrial nodes, and compact human-machine-interface controllers. Typical applications include low-power sensor nodes, energy meters, industrial monitoring equipment, portable measurement devices, security and access-control modules, and LCD-driven control panels. Its 112-BGA footprint offers fine-pitch routing opportunities, while the large I/O count reduces the need for external I/O expanders in connected embedded designs. PCB implementation requires careful BGA layout, controlled impedance for sensitive signals, and decoupling close to the supply pins. Follow Silicon Labs hardware-design guidance for EFM32G890 layouts, validate BGA assembly capability, and keep high-current return paths compact. This page also organizes package details, replacement options, application guidance, and design considerations for faster engineering evaluation.

Permintaan RFG Kontak
EFM32GG11B420F2048GQ100-B - 72MHz ARM Cortex-M4 MCU 2MB Flash | Silicon Labs
EFM32GG11B420F2048GQ100-B

EFM32GG11B420F2048GQ100-B - 72MHz ARM Cortex-M4 MCU 2MB Flash | Silicon Labs

The Silicon Labs EFM32GG11B420F2048GQ100-B is an ARM Cortex-M4 microcontroller from the EFM32 Giant Gecko Series 1 family, featuring a 32-bit processor core running at up to 72 MHz with DSP instruction support and a single-precision Floating Point Unit (FPU). It integrates 2 MB (2048 kB) of Flash and 512 kB of RAM, includes 83 digital I/O pins, 7× 16-bit timer/counters, USB, LCD controller, and a hardware cryptographic engine (AES, ECC, SHA, TRNG) in a 100-pin TQFP (14×14 mm) package. An ARM Cortex-M4 microcontroller is a 32-bit RISC processor core designed for embedded systems that require deterministic real-time response, low power consumption, and digital signal processing. The Giant Gecko family extends this with Silicon Labs' energy-friendliness techniques: 80 µA/MHz active current (EM0), 2.1 µA EM2 Deep Sleep current with 16 kB RAM retention and RTCC running, fast wake-up times, and a flexible Energy Management System (EMU). These characteristics position the part within the broader category of low-power 32-bit microcontrollers alongside competing Cortex-M4/M4F parts from STMicroelectronics, NXP, and Microchip. Key differentiating features include crystal-free low-energy USB, 5 V tolerant GPIO, robust capacitive touch sense, a Memory Protection Unit (MPU), Wake-up Interrupt Controller (WIC), and footprint compatibility with select EFM32 packages that simplify migration. The integrated peripheral reflex system and low-energy peripherals enable autonomous operation without CPU intervention, extending battery life in energy-harvesting and IoT applications. The part operates from 1.8 V to 3.6 V and supports the industrial temperature range of -40°C to +85°C. With 2048 kB of Flash and 512 kB of RAM, it is the highest-memory variant of the GG11 family and is suitable for complex GUI stacks, wireless protocol stacks (Zigbee, Thread, BLE co-processors), asset tracking firmware, and industrial HMI designs that demand both graphics and connectivity. Typical applications include IoT edge nodes, smart metering, building automation, industrial control panels with LCD, USB peripherals, and portable medical devices. The combination of USB, LCD, and hardware crypto on a single die enables compact, BOM-optimized designs. When designing with this MCU, allocate the 83 GPIO pins across your peripheral set early in the design phase; ensure the 1 µF + 100 nF decoupling pair is placed within 3 mm of the VDD pins, and route the USB DP/DM pair with 90 Ω differential impedance. Use Simplicity Studio and the Hardware Configurator tool to assign peripherals to pins and generate production-ready initialization code. This page synthesizes distributor pricing, drop-in GG11 alternatives, and practical design notes not found in the manufacturer datasheet to help engineers select and qualify the part faster.

Permintaan RFG Kontak
EFM32GG11B520F2048IM64-B - 72MHz ARM Cortex-M4 MCU 2MB Flash
EFM32GG11B520F2048IM64-B

EFM32GG11B520F2048IM64-B - 72MHz ARM Cortex-M4 MCU 2MB Flash

Silicon Labs EFM32GG11B520F2048IM64-B is a 32-bit microcontroller IC 36-A 32-bit ARM Cortex-M4 Giant Gecko S1 microcontroller running at 72 MHz, integrating 2 MB (2M x 8) of flash and 512 kB of RAM in a 64-pin QFN (9x9) package. It supports 1.8V to 3.8V supply, 53 digital I/O pins, 7 16-bit timer/counters, and energy-aware peripherals including LESENSE, IADC, and hardware crypto. The Giant Gecko family is engineered for ultra-low-power applications with fast wake-up times and energy-saving modes. An ARM Cortex-M4 microcontroller (MCU) is a 32-bit microcontroller unit based on the ARM Cortex-M4 processor core with DSP instructions and optional FPU, offering deterministic real-time performance at MHz clock speeds while consuming only tens of microamps per MHz in active mode. It fits within the hierarchy: Cortex-M4 MCU -> ARM-based microcontroller -> embedded microcontroller -> semiconductor. Battery voltage is critical for portable, energy-sensitive designs where sleep current dominates battery life. Key features include 2 MB flash, 512 kB RAM, 53 GPIO, hardware AES/SHA crypto accelerator, segment LCD controller, USB, CAN, EBI and other peripherals, 39 C/W thermal resistance (typical QFN-64), -40C to +125C industrial temperature grade, and multiple low-energy modes down to sub-uA sleep currents. The B-grade part variant features extended industrial temperature range and is supplied on tape and reel. The architecture combines ARM Cortex-M4 core with autonomous low-energy peripherals (LETIMER, RTCC, IADC, LESENSE) that operate without waking the CPU. The 2 MB flash supports over-the-air (OTA) firmware updates via dual-bank memory mapping, while the LCD controller enables direct drive of segmented displays without external driver ICs, reducing BOM cost and PCB area. Typical applications include battery-powered IoT sensor nodes, smart energy metering with ESE AMR and LCD displays, industrial HMI panels with capacitive touch, connected lighting with wireless-segment control, and asset tracking with GPS/GNSS. The EFM32GG11B520F2048IM64-B is particularly well-suited to designs that require large memory for firmware/RF stacks while maintaining years of battery life. When designing with this device, ensure adequate decoupling on VDD (1.8-3.8V) with 100 nF ceramic capacitors per supply pin and consider ground plane continuity under the QFN exposed pad for thermal dissipation. Order chips at tape and reel quantities via authorized distributors. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Permintaan RFG Kontak
EFM32GG230F1024G-E-QFN64 - 48MHz ARM Cortex-M3 MCU, 1MB Flash | Silicon Labs
EFM32GG230F1024G-E-QFN64

EFM32GG230F1024G-E-QFN64 - 48MHz ARM Cortex-M3 MCU, 1MB Flash | Silicon Labs

The Silicon Labs EFM32GG230F1024G-E-QFN64 is an ARM Cortex-M3 Giant Gecko microcontroller IC running at 48 MHz with 1 MB (1M x 8) of Flash and 128 KB of RAM, housed in a 64-pin QFN (9x9 mm) package with exposed thermal pad. It is a 32-bit single-core MCU engineered for energy-sensitive applications, offering autonomous peripherals, AES hardware encryption, and rich analog integration while consuming as little as 0.6 uA in Stop (EM2 Deep Sleep) mode and 180 uA/MHz in Run mode. What is a 32-bit low-power microcontroller? A microcontroller (MCU) is a system-on-chip that integrates a CPU core, program memory (Flash), data memory (RAM), and peripherals (timers, ADC, communication interfaces) into a single device. Low-power MCUs extend this concept by including multiple energy modes (Run, Sleep, Stop, EM4 shutoff), fast wake-up times, and peripheral reflex logic that lets timers and sensor interfaces operate without waking the CPU. The EFM32GG Giant Gecko family sits in the hierarchy as: Cortex-M3 MCU -> ARM 32-bit MCU -> low-energy MCU -> embedded microcontroller -> semiconductor IC. Key features include 1024 KB Flash, 128 KB RAM, 56 digital I/O pins, 4 x 16-bit timers, AES-128/256 hardware crypto accelerator, and a peripheral reflex system. The wide supply voltage range of 1.85 V to 3.8 V supports both single-cell Li-ion battery applications and 3.3 V industrial rails, while integrated LDO and DC-DC support enables flexible power tree design with sub-microamp sleep currents critical for battery-powered IoT endpoints. The Giant Gecko architecture pairs the Cortex-M3 core with Silicon Labs' LESENSE, LETIMER, RTCC, and AUTOSELECT peripherals, allowing sensor interfaces and GPIO events to operate autonomously while the CPU remains in deep sleep. Hardware AES acceleration and a True Random Number Generator (TRNG) target secure connected applications. The 9x9 mm QFN-64 footprint with exposed pad provides 56 usable GPIO - generous for a small-outline MCU package. Typical applications include battery-powered IoT sensors, smart energy metering, wireless sensor nodes, industrial HMI controllers, and home automation gateways where years of battery life and rich peripheral integration are required. When designing with this part, place a 1 uF X7R bypass capacitor adjacent to each VDD pin and a 4.7 uF bulk capacitor near the package. The QFN-64 thermal pad must be soldered to a continuous ground pour for both electrical ground and thermal dissipation (theta_JA typically 28 C/W on a 4-layer JEDEC JESD51-7 board). This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Permintaan RFG Kontak
EFM32GG290F1024-BGA112 - 32-bit ARM Cortex-M3 MCU, 1MB Flash | Silicon Labs
EFM32GG290F1024-BGA112

EFM32GG290F1024-BGA112 - 32-bit ARM Cortex-M3 MCU, 1MB Flash | Silicon Labs

The Silicon Labs EFM32GG290F1024-BGA112 is an ARM Cortex-M3 based 32-bit microcontroller from the Giant Gecko family, integrating 1024 kB of Flash and 128 kB of RAM, with a CPU core capable of up to 48 MHz operation (1.25 DMIPS/MHz). The device is housed in a 112-ball BGA package (10x10 mm) and offers 90 digital I/O pins, making it one of the highest-density members of the EFM32 Giant Gecko line. An ARM Cortex-M3 microcontroller (MCU) is a 32-bit RISC processor core designed for embedded applications that need deterministic real-time behavior, low power consumption, and a Thumb-2 instruction mix that balances code density with computational throughput. Cortex-M3 cores are widely deployed in IoT, sensor hubs, industrial controllers, and human-interface products, and are positioned hierarchically as: ARM Cortex-M3 -> 32-bit MCU -> microcontroller -> semiconductor. The EFM32 Giant Gecko series extends this architecture with Silicon Labs' proprietary low-energy peripherals, fast wake-up time from sleep states, and a peripheral reflex system that lets timers, ADCs, and GPIO events trigger DMA transfers without CPU intervention. Key differentiating features include 1 MB of on-chip Flash and 128 kB of SRAM, hardware AES encryption, a 12-bit ADC, multiple USART/UART/SPI/I2C peripherals, and a 4x16-bit timer/counter array. The 90 GPIO count and 112-ball BGA footprint make it a strong fit for industrial gateways and high-pin-count sensor hubs. The Cortex-M3 core also integrates a Memory Protection Unit (MPU) supporting up to 8 segments and a Wake-up Interrupt Controller for handling interrupts from sleep. Technically, the part operates from a single 1.98 V to 3.8 V supply, is qualified over -40 C to +85 C, and supports an integrated LDO and DC-DC regulator for core power. The energy-friendly design lets the device drop below 1 uA in deep-sleep modes while retaining RTC and interrupt capability, addressing battery-operated applications where both processing power and standby current matter. Typical applications include industrial IoT gateways, smart metering, home and building automation, asset tracking, wireless sensor nodes, security panels, and connected health devices. The 1 MB Flash tier also serves as a host for larger protocol stacks (Thread, ZigBee, BLE via co-processor) where ample code space is required. When designing with the EFM32GG290F1024-BGA112, plan PCB escape routing for the 112-ball BGA carefully - the 0.8 mm ball pitch demands 4 or more PCB layers with microvia stack-ups. Decoupling should follow the datasheet's reference layout, and the debug SWD pins (SWDIO/SWCLK) must be brought out to a standard ARM Cortex debug header for programming. This page synthesizes distributor pricing, drop-in BGA112 alternatives, and practical layout guidance not found in the manufacturer datasheet alone, helping engineers select the right Giant Gecko variant for high-density, low-energy embedded designs.

Permintaan RFG Kontak