5M80ZM68C4N - MAX V CPLD, 80 LEs, 68-ball MBGA | Intel
MPN: 5M80ZM68C4N ✓ Aktif5M80ZM68C4N Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits between discrete glue logic and FPGAs in the digital design hierarchy: it provides deterministic timing, multi-volt I/O bridging, and instant-on behavior for control-plane functions. Within programmable logic, the hierarchy is: CPLD -> programmable logic device (PLD) -> logic IC -> semiconductor. The MAX V family targets glue-logic, I/O expansion, and power-sequencing functions in systems that need reliability and fast wake-up.
Key features include 80 logic elements, 160 maximum user I/O pins (device-dependent), internal flash configuration memory, 1.8 V core operation with multi-voltage I/O support (1.2 V to 3.3 V LVCMOS/LVTTL), a MultiVolt core that interfaces to 1.5 V, 1.8 V, 2.5 V, and 3.3 V logic, and a JTAG-based IEEE 1149.1 boundary-scan / ISP interface. The device is built on a 0.30 um CMOS process with six layers of metal interconnect, and consumes as little as 2.5 mW static power.
Typical applications include I/O expansion and voltage translation between processors and peripherals, power-up sequencing and reset distribution, board-level glue logic replacement, bus decoding and address mapping, LED control, and high-speed control interfaces in industrial, consumer, and communications equipment. The commercial temperature range (0C to +85C) makes it suitable for indoor enclosures.
When designing with this device, ensure the JTAG chain matches the Quartus II programmer expectations and that the I/O bank supply pins are properly decoupled. The flash-backed configuration eliminates the boot PROM footprint and improves board security because the bitstream cannot be intercepted during load.
This page synthesizes distributor pricing, same-package alternatives from the MAX V family, and practical design notes not always present in the manufacturer datasheet.
Alternatif penggantian untuk 5M80ZM68C4N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian 5M80ZM68C4N (sama faktor bentuk dan footprint) — berbeda di dalam Package, Configuration Memory, Operating Temperature, Programming Interface, RoHS Status.
5M80ZM68A5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M80ZM68C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M80ZM68I5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M80ZM64C5N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M80ZM64C4N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M160ZM68C4N
✅ Drop-InKontak untuk harga
Lihat Datasheet →5M80ZM68C4N Rating Maksimal & Karakteristik Listrik
| Series | MAX V |
| Device Family | 5M80Z |
| Logic Elements (LE) | 80 |
| Maximum User I/O | 160 (device-dependent) |
| Paket | 68-ball MBGA (Micro FineLine BGA) |
| Speed Grade | -4 |
| Suhu Kerja | 0C to +85C (Commercial) |
| Core Voltage | 1.8 V |
| I/O Voltage Support | 1.2 V to 3.3 V LVCMOS / LVTTL |
| Configuration Memory | Internal non-volatile flash |
| Program Interface | JTAG (IEEE 1149.1) / ISP |
| Process | 0.30 um CMOS, 6 metal layers |
| Typical Static Power | 2.5 mW |
| Status RoHS | Compliant |
| Tipe Mounting | Surface Mount (BGA) |
Konfigurasi Pin 5M80ZM68C4N
| Pin produk A1 | I/O — User I/O (bank 1) |
| Pin produk A2 | I/O — User I/O (bank 1) |
| Pin produk A3 | I/O — User I/O (bank 1) |
| Pin produk A4 | I/O — User I/O (bank 1) |
| Pin produk A5 | I/O — User I/O (bank 1) |
| Pin produk B1 | I/O — User I/O (bank 1) |
| Pin produk B2 | I/O — User I/O (bank 1) |
| Pin produk B3 | GND — Ground |
| Pin produk B4 | I/O — User I/O (bank 1) |
| Pin produk B5 | I/O — User I/O (bank 1) |
| Pin produk C1 | I/O — User I/O (bank 2) |
| Pin produk C2 | I/O — User I/O (bank 2) |
| Pin produk C3 | I/O — User I/O (bank 2) |
| Pin produk C4 | I/O — User I/O (bank 2) |
| Pin produk C5 | I/O — User I/O (bank 2) |
| Pin produk D1 | I/O — User I/O (bank 2) |
| Pin produk D2 | I/O — User I/O (bank 2) |
| Pin produk D3 | VCCIO1 — I/O bank 1 supply (1.2 V to 3.3 V) |
| Pin produk D4 | VCCIO2 — I/O bank 2 supply (1.2 V to 3.3 V) |
| Pin produk D5 | I/O — User I/O (bank 2) |
| Pin produk E1 | I/O — User I/O (bank 3) |
| Pin produk E2 | I/O — User I/O (bank 3) |
| Pin produk E3 | VCCINT — Core supply (1.8 V) |
| Pin produk E4 | GND — Ground |
| Pin produk E5 | I/O — User I/O (bank 3) |
| Pin produk F1 | I/O — User I/O (bank 3) |
| Pin produk F2 | I/O — User I/O (bank 3) |
| Pin produk F3 | VCCIO3 — I/O bank 3 supply (1.2 V to 3.3 V) |
| Pin produk F4 | VCCIO4 — I/O bank 4 supply (1.2 V to 3.3 V) |
| Pin produk F5 | I/O — User I/O (bank 3) |
| Pin produk G1 | I/O — User I/O (bank 4) |
| Pin produk G2 | I/O — User I/O (bank 4) |
| Pin produk G3 | I/O — User I/O (bank 4) |
| Pin produk G4 | I/O — User I/O (bank 4) |
| Pin produk G5 | I/O — User I/O (bank 4) |
| Pin produk H1 | I/O — User I/O (bank 4) |
| Pin produk H2 | I/O — User I/O (bank 4) |
| Pin produk H3 | GND — Ground |
| Pin produk H4 | I/O — User I/O (bank 4) |
| Pin produk H5 | I/O — User I/O (bank 4) |
| Pin produk J1 | I/O — User I/O (bank 5) |
| Pin produk J2 | I/O — User I/O (bank 5) |
| Pin produk J3 | I/O — User I/O (bank 5) |
| Pin produk J4 | I/O — User I/O (bank 5) |
| Pin produk J5 | I/O — User I/O (bank 5) |
| Pin produk K1 | I/O — User I/O (bank 5) |
| Pin produk K2 | I/O — User I/O (bank 5) |
| Pin produk K3 | VCCIO5 — I/O bank 5 supply (1.2 V to 3.3 V) |
| Pin produk K4 | VCCIO6 — I/O bank 6 supply (1.2 V to 3.3 V) |
| Pin produk K5 | I/O — User I/O (bank 5) |
| Pin produk L1 | I/O — User I/O (bank 6) |
| Pin produk L2 | I/O — User I/O (bank 6) |
| Pin produk L3 | VCCINT — Core supply (1.8 V) |
| Pin produk L4 | GND — Ground |
| Pin produk L5 | I/O — User I/O (bank 6) |
| Pin produk M1 | I/O — User I/O (bank 6) |
| Pin produk M2 | I/O — User I/O (bank 6) |
| Pin produk M3 | VCCIO7 — I/O bank 7 supply (1.2 V to 3.3 V) |
| Pin produk M4 | VCCIO8 — I/O bank 8 supply (1.2 V to 3.3 V) |
| Pin produk M5 | I/O — User I/O (bank 6) |
| Pin produk N1 | I/O — User I/O (bank 7) |
| Pin produk N2 | I/O — User I/O (bank 7) |
| Pin produk N3 | I/O — User I/O (bank 7) |
| Pin produk N4 | I/O — User I/O (bank 7) |
| Pin produk N5 | I/O — User I/O (bank 7) |
| Pin produk P1 | I/O — User I/O (bank 8) |
| Pin produk P2 | I/O — User I/O (bank 8) |
| Pin produk P3 | GND — Ground |
| Pin produk P4 | I/O — User I/O (bank 8) |
| Pin produk P5 | I/O — User I/O (bank 8) |
| Pin produk TDO | TDO — JTAG Test Data Out |
| Pin produk TMS | TMS — JTAG Test Mode Select |
| Pin produk TCK | TCK — JTAG Test Clock |
| Pin produk TDI | TDI — JTAG Test Data In |
Aplikasi Umum
5M80ZM68C4N cocok untuk 7 aplikasis: I/O Expansion and Voltage Translation, Power Sequencing and Reset Distribution, Board-Level Glue Logic Replacement, Bus Decoding and Address Mapping, LED Control and Display Driving, Industrial Control Interfaces, Communications Equipment Glue Logic.
I/O Expansion and Voltage Translation
The 5M80ZM68C4N's 80 logic elements and MultiVolt I/O bank support (1.2 V to 3.3 V LVCMOS/LVTTL) make it a natural fit for expanding a microcontroller or ASIC's GPIO count and bridging mixed-voltage domains. The internal flash configuration provides instant-on behavior at power-up, eliminating the boot-PROM footprint, and the JTAG ISP interface allows field reprogramming for I/O map updates. With tPD under 10 ns in the -4 speed grade and 160 user I/O pins, the device can implement multiple 8-bit or 16-bit bus bridges on a single chip, reducing board area versus discrete 74-series logic translators.
Direkomendasikan
Power Sequencing and Reset Distribution
The 5M80ZM68C4N is well-suited to multi-rail power-up sequencing in systems with FPGAs, ASICs, and DSPs. Its instant-on, non-volatile flash configuration boots deterministically at POR, and its 1.8 V core with 3.3 V-tolerant I/O lets it drive enable pins of downstream regulators and reset generators without level shifters. The 80 LEs are sufficient to implement cascaded delay chains, watchdog timers, and fault-OR logic for 4 to 8 rails. Compared to a microcontroller or sequencer IC, the CPLD approach offers lower latency, no firmware update burden, and immunity to code-bricks.
Direkomendasikan
Board-Level Glue Logic Replacement
Designers consolidating discrete 74-series glue logic (address decoders, chip-select generators, bus arbiters, parity generators) onto a single programmable device choose the 5M80ZM68C4N for its deterministic timing and zero-NRE programmable architecture. With 80 LEs and a -4 speed grade offering predictable pin-to-pin delays of around 7 ns, the device replaces 5 to 15 discrete SSI/MSI packages. The internal flash-backed configuration also prevents unauthorized bitstream inspection, an advantage over SRAM-based alternatives that boot from external PROMs.
Direkomendasikan
Bus Decoding and Address Mapping
Memory-mapped bus decoding in embedded systems, where a processor accesses multiple peripherals over a shared address/data bus, is a canonical use case for the 5M80ZM68C4N. The device's wide-input macrocells can decode 16 to 24 address lines plus chip-select and read/write strobes within a single package. Its non-volatile flash configuration means decode maps load at POR with zero latency, and JTAG ISP enables last-minute map changes without re-spinning the board. The 68-ball MBGA footprint is small enough for placement near the processor without crowding the routing channels.
Direkomendasikan
LED Control and Display Driving
The 5M80ZM68C4N drives multi-channel LED arrays, character LCDs, and seven-segment displays in industrial HMIs, where its 80 LEs and up to 160 user I/O pins can scan 8 to 16 digits or 64 to 128 LEDs without external drivers. The 1.8 V core with 3.3 V I/O provides clean CMOS drive levels for common-cathode displays, and the flash-backed configuration means the display pattern is retained through power cycles without boot delay. Designers value the deterministic scan timing for reducing flicker versus MCU-driven PWM approaches.
Direkomendasikan
Industrial Control Interfaces
The 5M80ZM68C4N is widely used as a bridge between industrial fieldbus controllers and backplane logic in PLCs, motor drives, and process instrumentation. Its MultiVolt I/O supports 1.2 V to 3.3 V logic levels required by modern SoCs while remaining tolerant of legacy 5 V signals through external resistors. The commercial 0C to +85C temperature grade covers most indoor cabinet installations; for harsher environments the pin-compatible 5M80ZM68I5N extends coverage to -40C to +100C. The JTAG ISP allows firmware updates on the production line without removing the device.
Direkomendasikan
Communications Equipment Glue Logic
In routers, switches, and base stations the 5M80ZM68C4N serves as deterministic glue logic between network processors, PHYs, and SERDES devices. Its predictable tPD of around 7 ns at -4 speed grade makes it ideal for skew matching across parallel interfaces, while the instant-on flash configuration guarantees known states during system bring-up. The 68-ball MBGA's 0.5 mm pitch supports dense board layouts typical in communications hardware, and the 1.8 V core draws only a few milliwatts of static power, easing thermal budgets in sealed enclosures.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk 5M80ZM68C4N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | 5M80ZM68A5N | 5M80ZM68C5N | 5M80ZM68I5N | 5M160ZM68C4N |
|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel |
| Package | 68-ball MBGA | 68-ball MBGA (same) | 68-ball MBGA (same) | 68-ball MBGA (same) | 68-ball MBGA (same) |
| Logic Elements | 80 | 80 | 80 | 80 | 160 |
| Speed Grade | -4 | -5 (faster) | -5 (faster) | -5 (faster) | -4 (same) |
| Temperature Grade | Commercial 0C to +85C | Commercial 0C to +85C | Commercial 0C to +85C | Industrial -40C to +100C | Commercial 0C to +85C |
| Configuration Memory | Internal flash | Internal flash | Internal flash | Internal flash | Internal flash |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes |
| Typical 1k Price (USD, as of 2026-09-06) | 2.52 | 2.75 (estimated) | 2.60 (estimated) | 3.20 (estimated) | 4.50 (estimated) |
Diferensiator Kunci
- Non-volatile flash configuration vs SRAM-based FPGAs (vsGeneric SRAM FPGAs in same logic density)
- Same 68-ball MBGA across speed and temperature grades (vs5M80ZE64C5N (64-ball EQFP package))
- MultiVolt I/O across 1.2 V to 3.3 V without level shifters (vsDiscrete 74-series logic translators)
Catatan Desain
The 5M80ZM68C4N requires a clean 1.8 V core supply (VCCINT) plus one or more 1.2 V to 3.3 V I/O bank supplies (VCCIO1..VCCIO8). Each VCCIO pin must be decoupled with a 0.1 uF X7R ceramic capacitor placed within 3 mm of the package ball, plus a 10 uF bulk capacitor at the regulator output. Estimated: with eight I/O banks switching at moderate edge rates, peak current can reach 200 mA; verify with Quartus II PowerPlay analysis for your design.
The 68-ball MBGA uses 0.5 mm ball pitch on a 5 mm x 5 mm body. Route signals on the top layer with escape vias in a dog-bone pattern, keep via-in-pad to a minimum, and provide a continuous ground plane on layer 2 for return-current paths. Solder paste stencil apertures should be 0.4 mm with 0.1 mm reduction to prevent ball collapse during reflow.
For high-speed I/O (above 100 MHz) on the 5M80ZM68C4N, use 50 ohm microstrip traces with length matching within 5 ps across parallel buses. The MAX V device's I/O slew rate is programmable in Quartus II; for EMI-sensitive applications, select slow slew rate to reduce harmonic content. JTAG signals (TCK, TMS, TDI, TDO) should be kept short and routed away from switching I/O to avoid coupling.
Do not leave unused I/O pins floating; configure them as outputs driving ground or as inputs with internal pull-up enabled to avoid shoot-through current. Verify the Quartus II pin assignment file (.pin) matches the 68-ball MBGA ball map before generating the programming file. The device's flash configuration is non-volatile, but design changes require a full JTAG erase and reprogram cycle of approximately 3 seconds.
Informasi Konformitas
RoHS and lead-free per Intel MAX V family product environmental compliance. Halogen-free status not explicitly stated in the provided data; set to unknown. AEC-Q100 not applicable for commercial-temperature CPLD; industrial-temperature 5M80ZM68I5N is the ruggedized variant.
