Analog Devices

AD8013ANZ - Triple 150 MHz Video Amplifier | Analog Devices

MPN: AD8013ANZ ✗ Akhir Hidup
+5 V Vdss 30 mA Id 14-pin plastic DIP Package
MOQ: 1 |

AD8013ANZ Ringkasan

The Analog Devices AD8013ANZ is a low-power, triple current-feedback video amplifier with a 150 MHz bandwidth, 1000 V/us slew rate, and three amplifier channels in a 14-pin plastic DIP package. Each channel can deliver 30 mA of output current and is optimized for driving one back-terminated 150 ohm video load. The device accepts a single +5 V supply or dual supplies up to +/-6.5 V.

A current-feedback video amplifier is a high-speed amplifier topology used to process analog video signals with low distortion and good drive capability. The AD8013 belongs to the broader hierarchy of operational amplifiers, video amplifiers, and analog signal-chain ICs. Its three channels support economical multichannel designs where independent video paths must fit into a compact circuit footprint.

The AD8013ANZ provides three video amplifiers in one package, 150 MHz bandwidth, a 1000 V/us slew rate, and a high-speed shutdown function. The shutdown control can power down the amplifiers or place their outputs in a high-impedance state. These characteristics make the device useful when multiple video signals must be buffered, distributed, or selectively disabled without using three separate amplifier packages.

Each amplifier uses current feedback, allowing large-signal performance to remain useful across a broad frequency range. The manufacturer describes the output stage as capable of driving large capacitive loads, while the 30 mA per-channel output current is intended for standard back-terminated video networks. The AD8013 can operate from a single +5 V source or from dual positive and negative supplies extending to +/-6.5 V, giving designers flexibility in analog, industrial, broadcast, and instrumentation systems.

Typical uses include video routing, video distribution, RGB or component-video buffering, test and measurement signal conditioning, and multichannel imaging systems. The shutdown feature is particularly useful in systems where unused channels must be placed in a high-impedance state during test modes or power-management intervals. When designing around the amplifier, output loading and cable capacitance should be evaluated rather than assuming that the 150 MHz bandwidth alone guarantees acceptable performance.

A critical implementation detail is to place input, feedback, and decoupling connections for minimum loop area. Terminate video outputs in accordance with the intended network, and verify stability with the actual cable and load capacitance. Keep the power-supply return path compact because high-speed video signals can couple supply noise and board-trace inductance into the output.

This page organizes the manufacturer specifications, application guidance, comparison parameters, and practical design considerations for engineers evaluating the AD8013ANZ. It also identifies a verified same-package family alternative and documents where additional drop-in qualification is required before substitution.

Alternatif penggantian untuk AD8013ANZ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.

Variasi di dalam seri ini

Model-series yang sama yang kompatibel dengan penggantian AD8013ANZ (sama faktor bentuk dan footprint) — berbeda di dalam Package, Product Type.

Analog Devices
Package: 14-pin PDIP
Product Type: Single wideband precision operational amplifier
Bandingkan dengan AD8013ANZ →

AD8013AN

✅ Drop-In
📦 14-PDIP
AD8013AN omits the Z orderable suffix while retaining the 14-PDIP package and AD8013 triple video-amplifier architecture; confirm exact temperature grade and procurement status before substitution

📋 Alternatif referensi (tidak dalam katalog)

AD8013ANZ Rating Maksimal & Karakteristik Listrik

Product Type Triple current-feedback video amplifier
Number of Amplifier Channels 3 channels
Manufacturer Stated Bandwidth 150 MHz
-3 dB Bandwidth 140 MHz
Slew Rate 1000 V/us
Output Current per Channel 30 mA
Optimized Video Load 150 ohm back termination
Single-Supply Voltage +5 V
Single-Supply Operating Range 4.2 V to 13 V
Dual-Supply Voltage +/-2.1 V to +/-6.5 V
Arus Pemuat 3.5 mA
Amplifier Topology Current feedback
Shutdown Function High-speed disable with high-impedance output
Paket 14-pin plastic DIP
Tipe Mounting Through-hole

AD8013ANZ 14-pin plastic dip Diamant Konfigurasi Panduan

Konfigurasi pin untuk AD8013ANZ (14-pin plastic dip pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.

Diamant diagram pakai pakai 14-pin plastic dip untuk AD8013ANZ

Tidak ada data diatribut pin yang tersedia untuk AD8013ANZ.

Lihat ke: datasheet produk untuk konfigurasi pin penuh.

Aplikasi Umum

AD8013ANZ cocok untuk 6 aplikasis: RGB Video Signal Buffering, Video Distribution, Industrial Video Inspection, Test and Measurement Front Ends, Broadcast and Composite Video, Medical Video Interfaces.

📺

RGB Video Signal Buffering

The AD8013ANZ fits three-channel RGB buffering because it integrates three current-feedback video amplifiers, each capable of 30 mA of output drive and optimized for a 150 ohm back-terminated load. Place one amplifier on each red, green, and blue signal to reduce channel-to-channel board-routing differences while retaining 150 MHz manufacturer-stated bandwidth. The high 1000 V/us slew rate supports fast transition edges, but the actual video standard, cable capacitance, and termination must be checked during schematic capture. Keep each feedback loop compact and connect decoupling close to the device pins.

🌐

Video Distribution

The AD8013ANZ can buffer three related video paths in a distribution stage where space and channel consistency are important. Its three amplifier channels provide 150 MHz bandwidth, 1000 V/us slew rate, and 30 mA output current per channel, allowing each path to drive a conventional 150 ohm terminated network. The shutdown function can place unused outputs in a high-impedance state during mode changes or diagnostic intervals. Validate output settling and channel skew at the video bandwidth, and account for connector and cable capacitance when deciding whether additional isolation or termination is required.

🏭

Industrial Video Inspection

The AD8013ANZ is suitable for industrial inspection electronics that buffer three low-voltage video channels before digitization or monitoring. Its low 3.5 mA listed supply current supports compact instrumentation, while the triple topology reduces the number of amplifier packages needed beside a sensor interface. The 1000 V/us slew rate provides ample large-signal capability for fast transitions, and the high-speed disable can support controlled channel muting. Confirm the camera output amplitude, sync requirements, grounding strategy, and maximum cable length for the actual installation before releasing the PCB.

🔧

Test and Measurement Front Ends

The AD8013ANZ can condition three instrument signals when the source impedance and termination are compatible with a current-feedback amplifier. Its 150 MHz bandwidth, 30 mA per-channel output capability, and ability to drive large capacitive loads make it useful for high-speed buffer stages rather than precision low-noise reference amplifiers. Use the shutdown input to isolate channels during calibration, and verify that the selected gain network remains stable with the connected probe, cable, and fixture capacitance. The manufacturer feedback and gain tables should govern resistor selection.

📡

Broadcast and Composite Video

The AD8013ANZ can serve as a three-channel buffer in legacy broadcast and composite-video signal paths using standard terminated video connections. Each channel provides 150 MHz bandwidth and 30 mA output current for one 150 ohm load, while the three-channel package simplifies routing across a compact analog board. The shutdown function can provide high-impedance isolation during source switching or maintenance. Because modern broadcast interfaces may use different voltage, impedance, and timing requirements, engineers should verify the source standard and output waveform at the actual termination before selecting this device.

💊

Medical Video Interfaces

The AD8013ANZ may be used in legacy medical imaging interfaces that require three buffered analog-video channels, subject to application-specific safety and qualification review. Its triple architecture, 150 MHz bandwidth, and 1000 V/us slew rate suit rapid video transitions, and the high-speed disable allows unused channels to enter a high-impedance state. The device is not identified as AEC-Q100 qualified, and no medical certification is stated. Confirm isolation requirements, leakage, component suitability, and regulatory obligations for the complete system rather than treating the amplifier specification as product certification.

Ringkasan Produk Direkomendasikan

AD8013AN Same-package family alternative for triple video buffering Digunakan di dalam: RGB Video Signal Buffering, Video Distribution, Industrial Video Inspection, Test and Measurement Front Ends, Broadcast and Composite Video, Medical Video Interfaces AD8000YRDZ Single high-speed current-feedback amplifier reference Digunakan di dalam: RGB Video Signal Buffering, Industrial Video Inspection, Test and Measurement Front Ends, Medical Video Interfaces TLC27L4BIN Low-power quad operational amplifier alternative requiring qualification Digunakan di dalam: Video Distribution, Broadcast and Composite Video
What is the AD8013ANZ?
The AD8013ANZ is a low-power, triple current-feedback video amplifier from Analog Devices. It contains three independent amplifier channels in a 14-pin plastic DIP package, with 150 MHz manufacturer-stated bandwidth, 1000 V/us slew rate, and 30 mA output current per channel. According to the Analog Devices AD8013 datasheet, each channel is optimized for driving one back-terminated 150 ohm video load.
What is the bandwidth and slew rate of the AD8013ANZ?
The AD8013ANZ has 150 MHz manufacturer-stated bandwidth and a 1000 V/us slew rate. A separate distributor specification listing reports -3 dB bandwidth of 140 MHz, which is a different bandwidth convention from the manufacturer's headline figure. These high-speed ratings allow the current-feedback amplifiers to process fast-edge video signals while maintaining low distortion.
What supply voltages does the AD8013ANZ accept?
The AD8013ANZ accepts a single +5 V supply or dual supplies up to +/-6.5 V. The listed operating ranges are 4.2 V to 13 V for single-supply operation and +/-2.1 V to +/-6.5 V for dual-supply operation. According to the Analog Devices product information, the common-mode input range depends on the selected supply configuration and should be checked against the manufacturer pin-description table.
What is the shutdown function on the AD8013ANZ?
The AD8013ANZ has a high-speed disable function that can power down the amplifiers or place their outputs in a high-impedance state. This makes the shutdown control useful for channel isolation, test modes, and multichannel systems that disable unused video paths. Use the disable timing and output-state details in the manufacturer datasheet when designing control-sequence logic.
Where can I download the AD8013ANZ datasheet PDF?
The official AD8013ANZ documentation is available through the Analog Devices AD8013 product page at https://www.analog.com/en/products/ad8013.html. That page provides the manufacturer datasheet and product information. A third-party PDF mirror also appears in search listings, but the Analog Devices page is the preferred source for revision-controlled documentation and package information.
Where can I find the AD8013ANZ pinout?
The AD8013ANZ pinout is shown in the pin-description table of the Analog Devices AD8013 datasheet. The device is a 14-pin plastic DIP containing three current-feedback video amplifiers and associated power, shutdown, and feedback connections. Use the manufacturer pin-description table when assigning PCB tracks because several amplifier pins are dedicated to feedback and power connections.
Is the AD8013ANZ suitable for driving 150 ohm video loads?
Yes, the AD8013ANZ is specifically optimized for driving one back-terminated 150 ohm video load per amplifier channel. Each output provides 30 mA of drive current, making the device appropriate for conventional terminated analog-video paths. Cable length, connector capacitance, and the intended video standard should still be checked because external loading can affect gain and stability.
AD8013ANZ vs AD8013AN: which one should I choose?
AD8013ANZ and AD8013AN identify the same fundamental AD8013 triple video-amplifier device in the 14-pin plastic DIP configuration, with Z representing the specific lead-free/orderable designation for AD8013ANZ. For a new board, choose the exact orderable suffix approved by your purchasing organization. The AD8013AN is the closest same-package family alternative, but qualification should confirm temperature grade, marking, and procurement requirements.
When should I choose AD8013ANZ over a single video amplifier?
Choose AD8013ANZ when the design needs three independently buffered video channels in one 14-pin package. A single amplifier is appropriate when only one signal path exists, while three separate packages would consume additional board area and require separate decoupling. The AD8013ANZ is especially useful for RGB-style multichannel routing, video distribution, or instrumentation with three related analog outputs.
What can replace the AD8013ANZ?
The closest identified replacement is AD8013AN from Analog Devices because it retains the 14-pin plastic DIP format and the same AD8013 triple current-feedback amplifier architecture. Before making a substitution, verify the exact pin assignments, supply range, temperature grade, and any qualification or lifecycle restrictions. No additional same-package alternatives were confirmed from the available cross-reference results.
Is there a cross-brand drop-in replacement for the AD8013ANZ?
No cross-brand drop-in replacement is confirmed for the AD8013ANZ. The available cross-reference results do not establish that a competing 14-pin plastic DIP device has identical pin assignments, bandwidth, slew rate, shutdown behavior, and video-drive capability. Treat similarly packaged amplifiers as redesign candidates unless the manufacturer explicitly identifies them as pin-to-pin compatible.
Where can I buy the AD8013ANZ and check current availability?
Use the Request a Quote form on this page to request the AD8013ANZ, current stock status, and a lead-time quotation. The Request a Quote workflow is the appropriate route for availability because legacy video amplifiers can move between active and obsolete inventory without immediate changes to public catalog pages. Provide the required quantity, package preference, and target date with the request.
What is the price of the AD8013ANZ?
Use the Request a Quote form on this page for the current AD8013ANZ unit price and volume breaks. Pricing for a legacy analog IC can vary with quantity, condition, and inventory status, so a static price figure can become inaccurate quickly. The form allows the quotation to be matched to the requested quantity and procurement date.
How long is the lead time for the AD8013ANZ?
Request the current AD8013ANZ lead time through the Request a Quote form on this page. Lead time depends on manufacturer inventory, authorized distribution availability, and the requested quantity. A dated procurement request is essential for legacy components because market availability may change more quickly than ordinary catalog lead times.
What are the key specifications of the AD8013ANZ engineers should know?
The key AD8013ANZ specifications are three current-feedback channels, 150 MHz manufacturer-stated bandwidth, 1000 V/us slew rate, 30 mA output current per channel, 150 ohm optimized video loading, and high-speed shutdown. The package is 14-pin plastic DIP, with operation from +5 V single supply or dual supplies up to +/-6.5 V. According to the Analog Devices AD8013 datasheet, the device also supports driving large capacitive loads.

Data referensi engineering untuk AD8013ANZ — pembandingan, panduan desain, dan informasi konformitas.

Panduan Pemilihan

Choose the AD8013ANZ when an existing design needs three high-speed current-feedback video amplifiers in a 14-pin plastic DIP package. It is particularly appropriate for terminated analog-video paths requiring 150 MHz manufacturer-stated bandwidth, 1000 V/us slew rate, 30 mA output current per channel, and coordinated shutdown. Select AD8013AN when that exact orderable configuration is acceptable for the same AD8013 family and its procurement status has been confirmed. Consider AD8000YRDZ when redesigning around one ultrahigh-speed channel and its substantially higher 1.5 GHz bandwidth. Consider TLC27L4BIN only when lower operating speed is acceptable and the circuit can be redesigned around a quad low-power amplifier. No confirmed cross-brand drop-in replacement is identified, so a PCB-compatible substitution requires an explicit manufacturer pin-compatibility statement rather than package similarity alone.

Pembandingan dengan Alternatif

Parameter Umum Produk Ini AD8013AN
Package 14-PDIP 14-PDIP
Brand Analog Devices Analog Devices
Amplifier Channels 3 3
Topology Current feedback Current feedback
Manufacturer Stated Bandwidth 150 MHz 150 MHz
Slew Rate 1000 V/us 1000 V/us
Output Current per Channel 30 mA 30 mA
Optimized Video Load 150 ohm 150 ohm
Single-Supply Range 4.2 V to 13 V 4.2 V to 13 V
Dual-Supply Range +/-2.1 V to +/-6.5 V +/-2.1 V to +/-6.5 V
Shutdown Function High-speed disable with high-impedance output High-speed disable with high-impedance output

Diferensiator Kunci

  • Three high-speed video channels in one through-hole package (vsTLC27L4BIN)
  • Purpose-built video drive capability (vsAD8000YRDZ)
  • Integrated channel shutdown (vsTLC27L4BIN)

Catatan Desain

Keep each current-feedback amplifier's input and feedback paths short, direct, and isolated from high-current outputs. Place input and feedback resistors close to the relevant device pins, and avoid routing video traces beneath or immediately beside the power pins. A compact feedback loop reduces parasitic inductance and capacitance that can otherwise alter gain, ringing, and channel-to-channel timing.

Do not treat the 150 MHz headline bandwidth as independent of gain, supply, and output loading. Select the feedback resistors from the manufacturer gain and stability tables, verify the complete circuit with the intended 150 ohm termination, and test with the actual cable capacitance. A shutdown-controlled output enters a high-impedance state, but downstream circuitry must tolerate that state during mode transitions.

Decouple each supply rail close to the device and maintain a low-impedance return path. The device can operate from a single +5 V supply or dual supplies up to +/-6.5 V, so grounding and supply arrangements are not interchangeable in terms of headroom and signal range. Check output swing, input common-mode range, and load current against the selected supply configuration before finalizing the schematic.

Informasi Konformitas

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bebas Logam Lengket
Unknown
Bebas Halogena
Unknown
Mineral Konflik
Unknown

The Z suffix is an orderable designation, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited product information. The device is not identified as an automotive-qualified AEC-Q100 component.

Data disahkan pada: 2026-11-18 — data disahkan dan disusun oleh tim engineering komponen XAIPART

Pencarian Terkait

AD8013ANZ datasheet AD8013ANZ datasheet pdf AD8013ANZ pinout AD8013ANZ equivalent AD8013ANZ replacement AD8013ANZ cross reference AD8013ANZ price AD8013ANZ stock Analog Devices AD8013ANZ AD8013ANZ 150 MHz video amplifier AD8013ANZ 14-PDIP AD8013ANZ vs AD8013AN

Komponen dan Istilah Terkait

Analog Devices AD8013ANZ AD8013AN AD8000YRDZ TLC27L4BIN video amplifier current-feedback amplifier operational amplifier analog signal-chain IC triple amplifier 150 MHz bandwidth 1000 V/us slew rate 30 mA output current 150 ohm back termination single +5 V supply dual +/-6.5 V supply high-speed disable high-impedance output 14-pin plastic DIP through-hole package RGB video video distribution test and measurement industrial inspection broadcast video
Kutipan Cepat RFQ
Isi detail lengkap — tim penjualan kami akan membalas dalam 24 jam
Nomor Part Manufaktur Paket QTY Harga Target Lengkap
✓
Kutipan telah disubmit!

Kami akan membalas email Anda dalam 24 jam

1
RFQ Dikirim
2
Kutipan Diterima
3
Order Ditempatkan
4
Pembayaran
5
Dikirim
6
Dikirim
Lihat Detil RFQ