AD8013ANZ - Triple 150 MHz Video Amplifier | Analog Devices
料号: AD8013ANZ ✗ 停产AD8013ANZ 概述
A current-feedback video amplifier is a high-speed amplifier topology used to process analog video signals with low distortion and good drive capability. The AD8013 belongs to the broader hierarchy of operational amplifiers, video amplifiers, and analog signal-chain ICs. Its three channels support economical multichannel designs where independent video paths must fit into a compact circuit footprint.
The AD8013ANZ provides three video amplifiers in one package, 150 MHz bandwidth, a 1000 V/us slew rate, and a high-speed shutdown function. The shutdown control can power down the amplifiers or place their outputs in a high-impedance state. These characteristics make the device useful when multiple video signals must be buffered, distributed, or selectively disabled without using three separate amplifier packages.
Each amplifier uses current feedback, allowing large-signal performance to remain useful across a broad frequency range. The manufacturer describes the output stage as capable of driving large capacitive loads, while the 30 mA per-channel output current is intended for standard back-terminated video networks. The AD8013 can operate from a single +5 V source or from dual positive and negative supplies extending to +/-6.5 V, giving designers flexibility in analog, industrial, broadcast, and instrumentation systems.
Typical uses include video routing, video distribution, RGB or component-video buffering, test and measurement signal conditioning, and multichannel imaging systems. The shutdown feature is particularly useful in systems where unused channels must be placed in a high-impedance state during test modes or power-management intervals. When designing around the amplifier, output loading and cable capacitance should be evaluated rather than assuming that the 150 MHz bandwidth alone guarantees acceptable performance.
A critical implementation detail is to place input, feedback, and decoupling connections for minimum loop area. Terminate video outputs in accordance with the intended network, and verify stability with the actual cable and load capacitance. Keep the power-supply return path compact because high-speed video signals can couple supply noise and board-trace inductance into the output.
This page organizes the manufacturer specifications, application guidance, comparison parameters, and practical design considerations for engineers evaluating the AD8013ANZ. It also identifies a verified same-package family alternative and documents where additional drop-in qualification is required before substitution.
直接替换替代料: AD8013ANZ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: AD8013ANZ (相同外形与封装尺寸) ——差异在于 Package, Product Type.
AD8013AN
✅ 直接替换📋 参考替代料(不在目录中)
AD8013ANZ 最大额定值与电气特性
| Product Type | Triple current-feedback video amplifier |
| Number of Amplifier Channels | 3 channels |
| Manufacturer Stated Bandwidth | 150 MHz |
| -3 dB Bandwidth | 140 MHz |
| Slew Rate | 1000 V/us |
| Output Current per Channel | 30 mA |
| Optimized Video Load | 150 ohm back termination |
| Single-Supply Voltage | +5 V |
| Single-Supply Operating Range | 4.2 V to 13 V |
| Dual-Supply Voltage | +/-2.1 V to +/-6.5 V |
| 电源电流 | 3.5 mA |
| Amplifier Topology | Current feedback |
| Shutdown Function | High-speed disable with high-impedance output |
| 封装 | 14-pin plastic DIP |
| 安装类型 | Through-hole |
AD8013ANZ 14-pin plastic dip 引脚配置指南
AD8013ANZ(14-pin plastic dip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: AD8013ANZ.
请参阅 数据手册 以查看完整引脚配置。
典型应用
AD8013ANZ 适用于 6 应用s: RGB Video Signal Buffering, Video Distribution, Industrial Video Inspection, Test and Measurement Front Ends, Broadcast and Composite Video, Medical Video Interfaces.
RGB Video Signal Buffering
The AD8013ANZ fits three-channel RGB buffering because it integrates three current-feedback video amplifiers, each capable of 30 mA of output drive and optimized for a 150 ohm back-terminated load. Place one amplifier on each red, green, and blue signal to reduce channel-to-channel board-routing differences while retaining 150 MHz manufacturer-stated bandwidth. The high 1000 V/us slew rate supports fast transition edges, but the actual video standard, cable capacitance, and termination must be checked during schematic capture. Keep each feedback loop compact and connect decoupling close to the device pins.
推荐
Video Distribution
The AD8013ANZ can buffer three related video paths in a distribution stage where space and channel consistency are important. Its three amplifier channels provide 150 MHz bandwidth, 1000 V/us slew rate, and 30 mA output current per channel, allowing each path to drive a conventional 150 ohm terminated network. The shutdown function can place unused outputs in a high-impedance state during mode changes or diagnostic intervals. Validate output settling and channel skew at the video bandwidth, and account for connector and cable capacitance when deciding whether additional isolation or termination is required.
推荐
Industrial Video Inspection
The AD8013ANZ is suitable for industrial inspection electronics that buffer three low-voltage video channels before digitization or monitoring. Its low 3.5 mA listed supply current supports compact instrumentation, while the triple topology reduces the number of amplifier packages needed beside a sensor interface. The 1000 V/us slew rate provides ample large-signal capability for fast transitions, and the high-speed disable can support controlled channel muting. Confirm the camera output amplitude, sync requirements, grounding strategy, and maximum cable length for the actual installation before releasing the PCB.
推荐
Test and Measurement Front Ends
The AD8013ANZ can condition three instrument signals when the source impedance and termination are compatible with a current-feedback amplifier. Its 150 MHz bandwidth, 30 mA per-channel output capability, and ability to drive large capacitive loads make it useful for high-speed buffer stages rather than precision low-noise reference amplifiers. Use the shutdown input to isolate channels during calibration, and verify that the selected gain network remains stable with the connected probe, cable, and fixture capacitance. The manufacturer feedback and gain tables should govern resistor selection.
推荐
Broadcast and Composite Video
The AD8013ANZ can serve as a three-channel buffer in legacy broadcast and composite-video signal paths using standard terminated video connections. Each channel provides 150 MHz bandwidth and 30 mA output current for one 150 ohm load, while the three-channel package simplifies routing across a compact analog board. The shutdown function can provide high-impedance isolation during source switching or maintenance. Because modern broadcast interfaces may use different voltage, impedance, and timing requirements, engineers should verify the source standard and output waveform at the actual termination before selecting this device.
推荐
Medical Video Interfaces
The AD8013ANZ may be used in legacy medical imaging interfaces that require three buffered analog-video channels, subject to application-specific safety and qualification review. Its triple architecture, 150 MHz bandwidth, and 1000 V/us slew rate suit rapid video transitions, and the high-speed disable allows unused channels to enter a high-impedance state. The device is not identified as AEC-Q100 qualified, and no medical certification is stated. Confirm isolation requirements, leakage, component suitability, and regulatory obligations for the complete system rather than treating the amplifier specification as product certification.
推荐
推荐产品汇总
工程参考数据: AD8013ANZ ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | AD8013AN |
|---|---|---|
| Package | 14-PDIP | 14-PDIP |
| Brand | Analog Devices | Analog Devices |
| Amplifier Channels | 3 | 3 |
| Topology | Current feedback | Current feedback |
| Manufacturer Stated Bandwidth | 150 MHz | 150 MHz |
| Slew Rate | 1000 V/us | 1000 V/us |
| Output Current per Channel | 30 mA | 30 mA |
| Optimized Video Load | 150 ohm | 150 ohm |
| Single-Supply Range | 4.2 V to 13 V | 4.2 V to 13 V |
| Dual-Supply Range | +/-2.1 V to +/-6.5 V | +/-2.1 V to +/-6.5 V |
| Shutdown Function | High-speed disable with high-impedance output | High-speed disable with high-impedance output |
关键差异点
- Three high-speed video channels in one through-hole package (对比 TLC27L4BIN)
- Purpose-built video drive capability (对比 AD8000YRDZ)
- Integrated channel shutdown (对比 TLC27L4BIN)
设计说明
Keep each current-feedback amplifier's input and feedback paths short, direct, and isolated from high-current outputs. Place input and feedback resistors close to the relevant device pins, and avoid routing video traces beneath or immediately beside the power pins. A compact feedback loop reduces parasitic inductance and capacitance that can otherwise alter gain, ringing, and channel-to-channel timing.
Do not treat the 150 MHz headline bandwidth as independent of gain, supply, and output loading. Select the feedback resistors from the manufacturer gain and stability tables, verify the complete circuit with the intended 150 ohm termination, and test with the actual cable capacitance. A shutdown-controlled output enters a high-impedance state, but downstream circuitry must tolerate that state during mode transitions.
Decouple each supply rail close to the device and maintain a low-impedance return path. The device can operate from a single +5 V supply or dual supplies up to +/-6.5 V, so grounding and supply arrangements are not interchangeable in terms of headroom and signal range. Check output swing, input common-mode range, and load current against the selected supply configuration before finalizing the schematic.
合规信息
The Z suffix is an orderable designation, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited product information. The device is not identified as an automotive-qualified AEC-Q100 component.