AD8013ANZ - Triple 150 MHz Video Amplifier | Analog Devices
MPN: AD8013ANZ ✗ Cuối đờiAD8013ANZ Tóm tắt
A current-feedback video amplifier is a high-speed amplifier topology used to process analog video signals with low distortion and good drive capability. The AD8013 belongs to the broader hierarchy of operational amplifiers, video amplifiers, and analog signal-chain ICs. Its three channels support economical multichannel designs where independent video paths must fit into a compact circuit footprint.
The AD8013ANZ provides three video amplifiers in one package, 150 MHz bandwidth, a 1000 V/us slew rate, and a high-speed shutdown function. The shutdown control can power down the amplifiers or place their outputs in a high-impedance state. These characteristics make the device useful when multiple video signals must be buffered, distributed, or selectively disabled without using three separate amplifier packages.
Each amplifier uses current feedback, allowing large-signal performance to remain useful across a broad frequency range. The manufacturer describes the output stage as capable of driving large capacitive loads, while the 30 mA per-channel output current is intended for standard back-terminated video networks. The AD8013 can operate from a single +5 V source or from dual positive and negative supplies extending to +/-6.5 V, giving designers flexibility in analog, industrial, broadcast, and instrumentation systems.
Typical uses include video routing, video distribution, RGB or component-video buffering, test and measurement signal conditioning, and multichannel imaging systems. The shutdown feature is particularly useful in systems where unused channels must be placed in a high-impedance state during test modes or power-management intervals. When designing around the amplifier, output loading and cable capacitance should be evaluated rather than assuming that the 150 MHz bandwidth alone guarantees acceptable performance.
A critical implementation detail is to place input, feedback, and decoupling connections for minimum loop area. Terminate video outputs in accordance with the intended network, and verify stability with the actual cable and load capacitance. Keep the power-supply return path compact because high-speed video signals can couple supply noise and board-trace inductance into the output.
This page organizes the manufacturer specifications, application guidance, comparison parameters, and practical design considerations for engineers evaluating the AD8013ANZ. It also identifies a verified same-package family alternative and documents where additional drop-in qualification is required before substitution.
Bộ thay thế dễ dàng lắp đặt cho AD8013ANZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD8013ANZ (cùng hình factor và footprint) — khác nhau ở Package, Product Type.
AD8013AN
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD8013ANZ Tỷ lệ tối đa & tính chất điện
| Product Type | Triple current-feedback video amplifier |
| Number of Amplifier Channels | 3 channels |
| Manufacturer Stated Bandwidth | 150 MHz |
| -3 dB Bandwidth | 140 MHz |
| Slew Rate | 1000 V/us |
| Output Current per Channel | 30 mA |
| Optimized Video Load | 150 ohm back termination |
| Single-Supply Voltage | +5 V |
| Single-Supply Operating Range | 4.2 V to 13 V |
| Dual-Supply Voltage | +/-2.1 V to +/-6.5 V |
| Điện áp cung cấp | 3.5 mA |
| Amplifier Topology | Current feedback |
| Shutdown Function | High-speed disable with high-impedance output |
| Hộp | 14-pin plastic DIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân AD8013ANZ 14-pin plastic dip
Cấu hình chân cho AD8013ANZ (14-pin plastic dip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD8013ANZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD8013ANZ phù hợp cho 6 Áp dụngs: RGB Video Signal Buffering, Video Distribution, Industrial Video Inspection, Test and Measurement Front Ends, Broadcast and Composite Video, Medical Video Interfaces.
RGB Video Signal Buffering
The AD8013ANZ fits three-channel RGB buffering because it integrates three current-feedback video amplifiers, each capable of 30 mA of output drive and optimized for a 150 ohm back-terminated load. Place one amplifier on each red, green, and blue signal to reduce channel-to-channel board-routing differences while retaining 150 MHz manufacturer-stated bandwidth. The high 1000 V/us slew rate supports fast transition edges, but the actual video standard, cable capacitance, and termination must be checked during schematic capture. Keep each feedback loop compact and connect decoupling close to the device pins.
Được đề xuất
Video Distribution
The AD8013ANZ can buffer three related video paths in a distribution stage where space and channel consistency are important. Its three amplifier channels provide 150 MHz bandwidth, 1000 V/us slew rate, and 30 mA output current per channel, allowing each path to drive a conventional 150 ohm terminated network. The shutdown function can place unused outputs in a high-impedance state during mode changes or diagnostic intervals. Validate output settling and channel skew at the video bandwidth, and account for connector and cable capacitance when deciding whether additional isolation or termination is required.
Được đề xuất
Industrial Video Inspection
The AD8013ANZ is suitable for industrial inspection electronics that buffer three low-voltage video channels before digitization or monitoring. Its low 3.5 mA listed supply current supports compact instrumentation, while the triple topology reduces the number of amplifier packages needed beside a sensor interface. The 1000 V/us slew rate provides ample large-signal capability for fast transitions, and the high-speed disable can support controlled channel muting. Confirm the camera output amplitude, sync requirements, grounding strategy, and maximum cable length for the actual installation before releasing the PCB.
Được đề xuất
Test and Measurement Front Ends
The AD8013ANZ can condition three instrument signals when the source impedance and termination are compatible with a current-feedback amplifier. Its 150 MHz bandwidth, 30 mA per-channel output capability, and ability to drive large capacitive loads make it useful for high-speed buffer stages rather than precision low-noise reference amplifiers. Use the shutdown input to isolate channels during calibration, and verify that the selected gain network remains stable with the connected probe, cable, and fixture capacitance. The manufacturer feedback and gain tables should govern resistor selection.
Được đề xuất
Broadcast and Composite Video
The AD8013ANZ can serve as a three-channel buffer in legacy broadcast and composite-video signal paths using standard terminated video connections. Each channel provides 150 MHz bandwidth and 30 mA output current for one 150 ohm load, while the three-channel package simplifies routing across a compact analog board. The shutdown function can provide high-impedance isolation during source switching or maintenance. Because modern broadcast interfaces may use different voltage, impedance, and timing requirements, engineers should verify the source standard and output waveform at the actual termination before selecting this device.
Được đề xuất
Medical Video Interfaces
The AD8013ANZ may be used in legacy medical imaging interfaces that require three buffered analog-video channels, subject to application-specific safety and qualification review. Its triple architecture, 150 MHz bandwidth, and 1000 V/us slew rate suit rapid video transitions, and the high-speed disable allows unused channels to enter a high-impedance state. The device is not identified as AEC-Q100 qualified, and no medical certification is stated. Confirm isolation requirements, leakage, component suitability, and regulatory obligations for the complete system rather than treating the amplifier specification as product certification.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD8013ANZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD8013AN |
|---|---|---|
| Package | 14-PDIP | 14-PDIP |
| Brand | Analog Devices | Analog Devices |
| Amplifier Channels | 3 | 3 |
| Topology | Current feedback | Current feedback |
| Manufacturer Stated Bandwidth | 150 MHz | 150 MHz |
| Slew Rate | 1000 V/us | 1000 V/us |
| Output Current per Channel | 30 mA | 30 mA |
| Optimized Video Load | 150 ohm | 150 ohm |
| Single-Supply Range | 4.2 V to 13 V | 4.2 V to 13 V |
| Dual-Supply Range | +/-2.1 V to +/-6.5 V | +/-2.1 V to +/-6.5 V |
| Shutdown Function | High-speed disable with high-impedance output | High-speed disable with high-impedance output |
Bảo phân biệt quan trọng
- Three high-speed video channels in one through-hole package (vsTLC27L4BIN)
- Purpose-built video drive capability (vsAD8000YRDZ)
- Integrated channel shutdown (vsTLC27L4BIN)
Ghi chú thiết kế
Keep each current-feedback amplifier's input and feedback paths short, direct, and isolated from high-current outputs. Place input and feedback resistors close to the relevant device pins, and avoid routing video traces beneath or immediately beside the power pins. A compact feedback loop reduces parasitic inductance and capacitance that can otherwise alter gain, ringing, and channel-to-channel timing.
Do not treat the 150 MHz headline bandwidth as independent of gain, supply, and output loading. Select the feedback resistors from the manufacturer gain and stability tables, verify the complete circuit with the intended 150 ohm termination, and test with the actual cable capacitance. A shutdown-controlled output enters a high-impedance state, but downstream circuitry must tolerate that state during mode transitions.
Decouple each supply rail close to the device and maintain a low-impedance return path. The device can operate from a single +5 V supply or dual supplies up to +/-6.5 V, so grounding and supply arrangements are not interchangeable in terms of headroom and signal range. Check output swing, input common-mode range, and load current against the selected supply configuration before finalizing the schematic.
Thông tin tuân thủ
The Z suffix is an orderable designation, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited product information. The device is not identified as an automotive-qualified AEC-Q100 component.