AD9631AN - 320 MHz Low-Distortion Op Amp | Analog Devices
MPN: AD9631AN ✓ AktifAD9631AN Ringkasan
An operational amplifier is a high-gain, active analog circuit that uses differential feedback to amplify the voltage difference between its inputs. The AD9631 belongs to the voltage-feedback operational-amplifier family within the broader amplifier IC and semiconductor hierarchy. Its high bandwidth and low distortion make it suitable for communications, instrumentation, pulse-processing, video, and data-acquisition circuits requiring accurate amplification across a wide frequency range.
The AD9631AN provides 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth, allowing it to process signals well beyond the audio band. Analog Devices describes the device as a production ultralow-distortion, high-speed op amp that is stable at gain +1. The family also typically maintains approximately 65 degrees of phase margin, providing a useful stability consideration when designing wideband gain stages. Dual ±6 V operation supports bipolar signal paths and conventional analog-system supply architecture.
The AD9631 uses voltage-feedback architecture rather than current-feedback architecture. In a voltage-feedback implementation, closed-loop bandwidth, noise gain, and feedback resistance must be evaluated together. Designers should avoid treating the quoted small-signal and large-signal bandwidth values as interchangeable: small-signal bandwidth characterizes linear response around the operating point, while large-signal bandwidth reflects behavior under greater output excursions. Component tolerances, load capacitance, PCB parasitics, and feedback-network values can alter the practical response.
Typical uses include wideband receiver front ends, pulse-diode receiver circuits, test and measurement instrumentation, video signal paths, high-speed data acquisition, and communications equipment. The dual-supply arrangement can simplify biasing of bipolar or AC-coupled signals, although system designers must account for input and output common-mode limits, output swing, package thermal behavior, and the required bypass capacitance around a high-speed device.
PCB implementation requires short feedback paths, solid ground-plane continuity, and carefully placed supply bypassing. High-speed traces should be kept short, controlled-impedance where applicable, and isolated from noisy switching nodes. Decoupling capacitors should connect to the supply and ground pins with minimal loop area. Input and output protection networks should be analyzed for capacitance because probe, connector, and protection-diode loading can materially affect bandwidth, peaking, and settling behavior.
This page combines the manufacturer's product information, family datasheet characteristics, verified distributor references, and practical guidance for high-speed amplifier layouts. It also identifies the limits of verified substitute information so engineers can distinguish exact-footprint options from functionally similar amplifiers that require different packages or different stability characteristics.
Alternatif penggantian untuk AD9631AN — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian AD9631AN (sama faktor bentuk dan footprint) — berbeda di dalam Package.
AD9632AN
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →AD9631AN Rating Maksimal & Karakteristik Listrik
| Amplifier Type | Voltage-feedback operational amplifier |
| Small-Signal Bandwidth | 320 MHz |
| Large-Signal Bandwidth | 250 MHz |
| Stable Gain | +1 |
| Typical Phase Margin | 65 degrees |
| Supply Voltage Range | ±6 V |
| Total Supply Voltage | 12 V |
| Paket | 8-pin PDIP |
| Jumlah Pin | 8 pins |
| Tipe Mounting | Through-hole |
| Production Status | Production |
AD9631AN 8-pin pdip Diamant Konfigurasi Panduan
Konfigurasi pin untuk AD9631AN (8-pin pdip pakai pakai). Komponen analog ini memiliki pin masukan, keluaran, dan pengirim daya. Lihat datasheet produsen untuk konfigurasi pin offset null, kompensasi, dan pengaktifan. Ideal untuk peralatan sinyal dan kabel penggandaran.
Tidak ada data diatribut pin yang tersedia untuk AD9631AN.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
AD9631AN cocok untuk 6 aplikasis: Wideband Receiver Front End, Pulse-Diode Receiver Amplification, High-Speed Data Acquisition, Video Signal Conditioning, Test and Measurement Instrumentation, Communications Signal Conditioning.
Wideband Receiver Front End
The AD9631AN fits a wideband receiver front end because its 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth preserve signal amplitude across high-frequency operating bands. Its unity-gain stability supports buffer or low-gain signal-conditioning stages where cascading multiple gain stages would otherwise reduce usable bandwidth. In a practical implementation, the amplifier sits between the RF or baseband input network and the following converter or demodulator. The designer must preserve the impedance environment expected by the input source and account for the ±6 V supply rails. Probe, connector, and protection-device capacitance should be included in simulation because the layout parasitics can affect the otherwise high-bandwidth response.
Direkomendasikan
Pulse-Diode Receiver Amplification
The AD9631AN is suitable for pulse-diode receiver amplification because Analog Devices identifies the family as an ultralow-distortion, high-speed voltage-feedback amplifier. Its 320 MHz small-signal bandwidth provides ample frequency-range margin for handling short detector pulses and fast transition edges, while gain-of-+1 stability simplifies direct buffering. The amplifier is typically placed in the receiver’s analog signal path with feedback components chosen to establish the required closed-loop gain. Component parasitics and board inductance become increasingly important as pulse edges become shorter. Maintain short feedback loops, provide local supply bypassing, and verify output swing against the receiver’s detector amplitude to avoid clipping.
Direkomendasikan
High-Speed Data Acquisition
The AD9631AN can serve as the analog amplifier preceding a high-speed data-acquisition converter because its 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth support rapid signal transitions. Gain-of-+1 stability is useful when preserving signal integrity and bandwidth are more important than obtaining large closed-loop gain. Place the device close to the converter input to minimize trace loss and susceptibility to interference. The dual ±6 V supply arrangement supports bipolar signal conditioning, but the complete data-acquisition front end must verify input common-mode range, output swing, settling behavior, and ADC input compatibility. Probe capacitance and connector reflections should be included in the simulation rather than treated only as layout details.
Direkomendasikan
Video Signal Conditioning
The AD9631AN is appropriate for wideband video signal-conditioning stages that require low distortion and substantially more bandwidth than conventional general-purpose amplifiers. Its 320 MHz small-signal bandwidth covers high-definition and multi-standard video signal paths, while the gain-of-+1 stability supports unity-gain buffering between a source and a downstream display or processing circuit. Preserve the source and load impedances to avoid unintended gain errors. Use short traces and a continuous reference plane, and place supply-decoupling capacitors close to the pins. The design must also check video amplitude, sync timing, output swing, and the bandwidth roll-off at the highest supported pixel rate rather than relying only on the headline bandwidth number.
Direkomendasikan
Test and Measurement Instrumentation
The AD9631AN fits high-speed test and measurement instrumentation because its 320 MHz small-signal bandwidth and 250 MHz large-signal bandwidth support rapid-edge signal acquisition, while low distortion is important when preserving the shape and amplitude of measured waveforms. The gain-of-+1 characteristic allows the device to serve as a stable buffer between a source and a measurement instrument. Keep the input path short and use controlled-impedance routing when cable or fixture transitions are unavoidable. Because cables, probes, and protection devices add capacitance, evaluate their combined loading against the closed-loop response. Dual ±6 V operation also makes the device appropriate for bipolar measurement paths, subject to common-mode and output-swing checks.
Direkomendasikan
Communications Signal Conditioning
The AD9631AN supports communications signal-conditioning circuits that process wideband analog waveforms before conversion, demodulation, or further analog processing. Its 320 MHz small-signal bandwidth provides substantial headroom for high-rate channels, and the specified gain-of-+1 stability supports direct buffering. The amplifier may be placed after a mixer or receiver stage where signal amplitude must be retained without introducing substantial gain shaping. Designers should verify that the source impedance, feedback network, and load do not degrade stability. Supply decoupling and grounding are especially important because switching regulators, clock circuitry, and high-speed digital signals can couple noise into the analog node and distort the communication waveform.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk AD9631AN — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | AD9632AN |
|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP |
| Brand | Analog Devices | Analog Devices |
| Amplifier Architecture | Voltage feedback | Voltage feedback |
| Large-Signal Bandwidth | 250 MHz | 250 MHz |
| Specified Stable Gain | +1 | +2 |
| Typical Phase Margin | 65 degrees | 65 degrees |
Diferensiator Kunci
- Unity-gain stability is the principal functional distinction from AD9632AN (vsAD9632AN)
- Higher stated small-signal bandwidth than the large-signal rating (vsAD9632AN)
- Dual ±6 V operation supports conventional bipolar analog signal paths (vsAD9632AN)
Catatan Desain
Place every supply-bypass capacitor directly beside the corresponding AD9631AN power and ground pins, using the shortest possible connection to the ground plane. Keep feedback resistors close to the amplifier and avoid routing high-speed input traces beside digital clocks, switching inductors, or connector return paths. The 320 MHz small-signal bandwidth makes trace inductance, parasitic capacitance, and ground discontinuity relevant to actual performance, so evaluate the final layout with an S-parameter or transient simulation where tooling permits.
Treat source impedance, load capacitance, probe capacitance, and protection-device capacitance as part of the amplifier design rather than as external accessories. These impedances interact with the feedback network and can reduce bandwidth or introduce peaking. According to the Analog Devices AD9631/AD9632 family datasheet, the amplifier typically maintains approximately 65 degrees of phase margin, but stable operation still requires checking the complete circuit with realistic loading and supply bypassing.
Do not substitute a gain-of-+2 family member for AD9631AN without reviewing the closed-loop gain and stability requirements. AD9631AN is specifically identified as stable at gain +1, while the family documentation distinguishes the AD9632 gain +2 bandwidth behavior. Also verify common-mode range, output swing, supply sequencing, and the output load before energizing a new design; headline bandwidth alone does not establish compatibility with a particular signal chain.
Keep the 8-pin PDIP implementation away from long shared ground returns and noisy source nodes. Use a continuous ground plane where possible, avoid stubs, and provide close supply bypassing even when the surrounding system includes additional bulk capacitors. For laboratory prototypes, short twisted or coaxially routed connections are preferable to long loose hookup wire, because even a modest test lead can disturb a circuit intended to operate at hundreds of megahertz.
Informasi Konformitas
The available product and datasheet information does not explicitly identify RoHS, REACH, lead-free, halogen-free, or conflict-mineral status for AD9631AN. AEC-Q100 qualification is not applicable to this general-purpose operational amplifier.