ATSAMD20G15B-AU - 48MHz Cortex-M0+ MCU | Microchip
MPN: ATSAMD20G15B-AU ✓ AktifATSAMD20G15B-AU Ringkasan
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, and peripherals into one device. The ATSAMD20G15 belongs to the SAM D20 family and sits within the hierarchy of embedded controller, 32-bit microcontroller, Arm Cortex-M0+ processor, and semiconductor. Its combination of moderate flash capacity, SRAM, and low-power-oriented peripherals makes it suitable for cost-sensitive control nodes rather than graphics-intensive or high-end applications.
Key features include operation up to 48 MHz, 38 I/O pins, 23 peripheral interrupt channels, and support for I2C, SPI, UART, PWM, and ADC functions. The 32 KB flash provides embedded program storage, while 4 KB of SRAM supports working memory, stack operations, buffers, and peripheral data handling. A 1.62 V to 3.63 V operating range supports both 3.3 V and lower-voltage system designs when individual peripheral and I/O limits permit.
The Arm Cortex-M0+ architecture uses a compact instruction set and deterministic interrupt-oriented design. This simplifies firmware development for home automation, metering, consumer products, and industrial controllers. The 12-bit ADC allows analog sensors to be connected directly to the MCU, while the serial interfaces reduce demand for external interface chips when communicating with sensors, memory, displays, or downstream controllers.
Typical applications include smart-home sensor nodes, utility and resource meters, compact industrial controllers, consumer appliances, lighting interfaces, and low-cost embedded equipment. In a metering design, the ADC can acquire sensor signals while UART, SPI, or I2C connects the controller to an external network or storage device. The 38 available I/O pins also allow multiple digital inputs, outputs, and communication functions to be integrated on one board.
PCB implementation should preserve short, controlled signal paths around the MCU, provide appropriate decoupling near the supply pins, and route high-current outputs separately from sensitive analog inputs. Firmware must also observe individual peripheral voltage, frequency, and timing limits rather than assuming every function can operate simultaneously at the maximum 48 MHz clock.
This page combines the manufacturer product information with package, memory, interface, and application guidance. It also distinguishes pin-compatible sourcing variants and identifies where application-specific verification is required before hardware release.
Alternatif penggantian untuk ATSAMD20G15B-AU — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian ATSAMD20G15B-AU (sama faktor bentuk dan footprint) — berbeda di dalam Package, Mounting Type, Operating Temperature Range, RoHS Status, SRAM.
ATSAMD20G15B-AUT
✅ Drop-InKontak untuk harga
Lihat Datasheet →ATSAMD20G15B-AU Rating Maksimal & Karakteristik Listrik
| Product Type | 32-bit ARM Cortex-M0+ flash microcontroller |
| Maximum CPU Frequency | 48 MHz |
| CPU Architecture | Arm Cortex-M0+ |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 4 KB |
| Operating Voltage Range | 1.62 V to 3.63 V |
| ADC Resolution | 12 bit |
| Number of I/O Pins | 38 |
| Peripheral Interrupt Channels | 23 |
| Serial Interfaces | I2C, SPI, UART |
| Timer/PWM Support | PWM |
| Paket | 48-pin TQFP (7 x 7 mm) |
| Tipe Mounting | Surface mount |
| Rentang Suhu Kerja | -40 C to +85 C |
| Status Lingkungan Hidup | Active |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_qualified |
ATSAMD20G15B-AU 48-pin tqfp (7 x 7 mm) Diamant Konfigurasi Panduan
Konfigurasi pin untuk ATSAMD20G15B-AU (48-pin tqfp (7 x 7 mm) pakai pakai). IC digital ini termasuk GPIO, antarmuka komunikasi (UART, SPI, I2C), dan pin kuasa. Lihat datasheet produsen untuk fungsi pin alternatif dan opsi konfigurasi. Penting untuk desain sistem pengemasan dan PCB.
Tidak ada data diatribut pin yang tersedia untuk ATSAMD20G15B-AU.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
ATSAMD20G15B-AU cocok untuk 6 aplikasis: Smart Home Sensor Nodes, Utility and Resource Metering, Consumer Appliance Control, Industrial Control Modules, LED Lighting and Dimming Control, Low-Cost Data Acquisition Module.
Smart Home Sensor Nodes
The ATSAMD20G15B-AU fits compact smart-home sensor nodes that combine digital inputs, analog measurements, and low-speed communications. Its 48 MHz Cortex-M0+ processor can debounce switches, filter sensor readings, and manage protocol tasks, while 38 I/O pins reduce the need for external I/O expanders. I2C and SPI support common environmental sensors, while UART provides a straightforward path to a gateway. The 32 KB flash is sufficient for focused firmware, and the 4 KB SRAM can support protocol buffers and application state. A 3.3 V implementation should still include local decoupling and verify that every attached peripheral shares compatible logic levels.
Direkomendasikan
Utility and Resource Metering
The ATSAMD20G15B-AU is well suited to compact metering systems that acquire analog sensor signals and periodically report results. Its 12-bit ADC provides sufficient resolution for many cost-sensitive measurement circuits, while the 48 MHz Cortex-M0+ core supports calibration, filtering, accumulation, and status tracking. Serial interfaces can connect the meter to a display, storage device, or communications module, and the 38 I/O pins support tamper inputs, relay control, and indicators. The 32 KB flash stores application firmware and calibration parameters, while 4 KB of SRAM accommodates working buffers. Precision designs should use the manufacturer’s ADC guidance and shield sensitive analog routing from switching and high-current traces.
Direkomendasikan
Consumer Appliance Control
The ATSAMD20G15B-AU can coordinate motors, buttons, indicators, and sensors in a compact consumer appliance. Its PWM-capable peripherals support dimming, actuator timing, and motor-control functions, while the 48-pin TQFP package provides access to 38 I/O pins for panel inputs and discrete outputs. The 32-bit Cortex-M0+ processor handles state machines and communication protocols more efficiently than a simple fixed-function controller. UART, I2C, and SPI allow the MCU to connect a display, sensor module, or external driver. Design effort should focus on safe output states during reset and power loss, while the 1.62 V to 3.63 V range allows the supply architecture to be selected according to the appliance’s efficiency and noise requirements.
Direkomendasikan
Industrial Control Modules
The ATSAMD20G15B-AU supports small industrial control modules requiring deterministic peripheral handling, flexible serial connectivity, and a modest embedded footprint. The 23 peripheral interrupt channels allow events from communications, timers, and external sensors to be serviced without polling every device. I2C and SPI can connect sensors and industrial memories, UART can support service consoles or field-bus transceivers, and PWM can control actuators or indicators. With 32 KB of flash and 4 KB of SRAM, the device targets focused control tasks rather than extensive data logging. Production designs should isolate field-side signals from the MCU, provide robust decoupling, and verify operating-temperature requirements across the complete industrial enclosure.
Direkomendasikan
LED Lighting and Dimming Control
The ATSAMD20G15B-AU is appropriate for LED lighting modules that require dimming, status indication, and serial configuration. Its PWM peripherals can generate controlled drive signals for LED drivers, while the 12-bit ADC can monitor a feedback or current-sense voltage when the board architecture provides one. The 38 I/O pins allow multiple channel selection, fault inputs, and communication lines without a large logic footprint. A compact appliance can store lighting profiles and control logic in the 32 KB flash, with 4 KB of SRAM reserved for buffers and state. Designers should account for LED-driver startup behavior, ensure fault outputs remain in a defined state during reset, and separate high-current LED paths from sensitive analog and MCU grounding paths.
Direkomendasikan
Low-Cost Data Acquisition Module
The ATSAMD20G15B-AU can serve as the control element in a compact data-acquisition module built around external sensors and converters. Its 12-bit ADC handles moderate-resolution measurements, while SPI and I2C allow high-speed or multi-channel converter data to be transferred into the MCU. The 48 MHz core provides enough processing throughput for scaling, filtering, calibration, and packet preparation, and 4 KB of SRAM can support acquisition buffers. The 38 I/O pins make it practical to add digital status, trigger, and communication signals. For designs needing greater resolution, an external ADC such as MCP3301 can be evaluated alongside the on-chip converter. Layout should separate analog inputs from digital clocks and provide local bypass capacitance at the MCU supply pins.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk ATSAMD20G15B-AU — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | ATSAMD20G15B-AUT |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz |
| Flash Memory | 32 KB (32K x 8) | 32 KB (32K x 8) |
| SRAM | 4 KB | 4 KB |
| Operating Voltage Range | 1.62 V to 3.63 V | 1.62 V to 3.63 V |
| ADC Resolution | 12 bit | 12 bit |
| I/O Pins | 38 | 38 |
| Peripheral Interrupt Channels | 23 | 23 |
| Serial Interfaces | I2C, SPI, UART | I2C, SPI, UART |
| Ordering Suffix | -AU | -AUT |
Diferensiator Kunci
- Peripheral integration for compact embedded-control boards (vsATSAMD20G15B-AUT)
- Direct compatibility with an existing 48-TQFP land pattern (vsATSAMD20G15B-AUT)
- Balanced memory and I/O capability for compact controllers (vsATSAM4S16BA-MUR)
Catatan Desain
Place the MCU supply bypass capacitors directly beside their associated power pins, with the shortest possible return path through the ground plane. Route analog sensor inputs away from PWM outputs, clock signals, and switching-node copper. Because the device supports multiplexed peripheral functions, finalize the pin assignment before routing and preserve the package land pattern defined in the Microchip mechanical drawing.
Use a supply design that keeps the MCU within its 1.62 V to 3.63 V operating range under transient conditions. Do not assume that every I/O, ADC, or communication peripheral can tolerate the full range simultaneously; check each pin’s electrical limits and external-device levels. Establish defined states for outputs and enable paths during reset so external drivers and actuators cannot enter an unsafe condition.
Separate analog and digital return paths where practical, keep the ADC input traces short, and locate any input filtering components close to the source. The 48 MHz maximum clock requires a clean power and ground environment, particularly when ADC measurements and serial interfaces operate concurrently. Validate signal integrity and temperature behavior at the intended clock frequency rather than relying only on nominal software configuration.
Check firmware and board assumptions against the actual ATSAMD20G15B pin-multiplexing matrix. Avoid enabling multiple peripherals on one I/O pin without resolving the alternate-function conflict. Also size firmware, interrupt tables, stack usage, and DMA or communication buffers against the 32 KB flash and 4 KB SRAM limits before freezing the production software image.
Informasi Konformitas
The manufacturer identifies the device as active, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration appears in the cited product and distributor information. AEC-Q100 qualification is not indicated for this ordering code.