DG408CJ+ - 8:1 CMOS Analog Multiplexer | Analog Devices
MPN: DG408CJ+ ✓ AktifDG408CJ+ Ringkasan
An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output terminal. The DG408CJ+ belongs to the broader analog switch and multiplexer family, where CMOS construction provides low power consumption, TTL/CMOS-compatible address controls, and bidirectional signal conduction. Unlike a mechanical rotary switch, it can change channels electronically while maintaining a defined low on-resistance.
Key electrical features include guaranteed matching between channels of 8 ohm maximum and on-resistance flatness of 9 ohm maximum across the specified signal range. Charge injection is limited to 15 pC maximum, while input off-leakage current is specified at 5 nA maximum at +85 °C. Rail-to-rail signal handling, ESD protection greater than 2000 V per MIL-STD-883 Method 3015.7, and low power consumption of 1.25 mW maximum support precision and instrumentation applications.
The device uses three binary address lines to select one of eight channels. A low enable level places the multiplexer in shutdown mode, reducing power consumption and isolating the common output. Address and enable inputs accept TTL/CMOS logic levels, allowing direct control from common microcontrollers, FPGAs, and data-acquisition systems. The common output and individual inputs support analog signals referenced to the applicable positive or negative supply rails.
Typical uses include multimeter and automated test equipment input switching, data-acquisition systems, industrial process measurement, sample-and-hold networks, and analog signal routing. The DG408CJ+ is especially useful when eight measurement sources must reach a shared amplifier, converter, or instrumentation amplifier while keeping channel resistance and injection error tightly controlled.
Designers should confirm the supply configuration, logic thresholds, and signal amplitude before layout. Keep analog traces short, provide a stable ground reference, and use the pin-description table in the manufacturer data sheet when assigning PCB tracks. Allow settling time after changing the address or enable state because charge injection and parasitic capacitance can produce a transient step on the common output.
Alternatif penggantian untuk DG408CJ+ — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DG408CJ+ (sama faktor bentuk dan footprint) — berbeda di dalam Input Off-Leakage Current, Logic Compatibility, Mounting Type, Multiplexer Configuration, On-Resistance.
DG408CJ
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG408DJ+
✅ Drop-InKontak untuk harga
Lihat Datasheet →DG408AK/883B
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG408CJ+ Spesifikasi
| Multiplexer Configuration | 8:1 single-ended analog multiplexer |
| Number of Channels | 8 channels |
| Number of Functions | 1 function |
| On-Resistance | 100 ohm maximum |
| Channel Matching | 8 ohm maximum |
| On-Resistance Flatness | 9 ohm maximum over the specified signal range |
| Charge Injection | 15 pC maximum |
| Input Off-Leakage Current | 5 nA maximum at +85 °C |
| Single-Supply Voltage Range | +5 V to +30 V |
| Dual-Supply Voltage Range | ±5 V to ±20 V |
| Power Consumption | 1.25 mW maximum |
| Signal Handling | Rail-to-rail |
| Logic Compatibility | TTL/CMOS compatible |
| ESD Protection | Greater than 2000 V per MIL-STD-883 Method 3015.7 |
| Process Technology | CMOS |
| Paket | 16-pin PDIP |
| Tipe Mounting | Through-hole |
DG408CJ+ 16-pin pdip Diamant Konfigurasi Panduan
Konfigurasi pin untuk DG408CJ+ (16-pin pdip pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DG408CJ+.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DG408CJ+ cocok untuk 6 aplikasis: Multimeter and Automated Test Equipment, Data Acquisition Systems, Industrial Process Signal Routing, Sample-and-Hold Signal Conditioning, Audio and Instrumentation Signal Routing, Programmable Signal Conditioning.
Multimeter and Automated Test Equipment
The DG408CJ+ suits a digital multimeter or automated tester that must route eight input terminals to one measurement chain. Its 100 ohm maximum on-resistance is small relative to the input impedance of most digital voltmeters, while 8 ohm maximum channel matching helps limit gain errors when comparisons are made across channels. The TTL/CMOS-compatible address and enable inputs connect directly to test sequencer logic. Allow the common output to settle after each address change because the specified 15 pC maximum charge injection can create a transient step.
Direkomendasikan
Data Acquisition Systems
The DG408CJ+ can select among eight analog inputs in a multichannel data-acquisition system feeding a shared converter or instrumentation amplifier. The multiplexer minimizes channel-to-channel resistance variation to 8 ohm maximum and maintains on-resistance flatness within 9 ohm maximum over the specified signal range. Use the enable input to place the device in a shutdown state between conversions, and keep the common trace short to limit parasitic capacitance. A low-noise amplifier following the mux then establishes the system noise floor.
Direkomendasikan
Industrial Process Signal Routing
The DG408CJ+ supports industrial process monitoring by routing pressure, temperature, or current-sense signals from multiple sensors to a common signal-conditioning amplifier. The rail-to-rail signal-handling capability allows operation close to the applicable supply rails, while TTL/CMOS-compatible control inputs simplify interfacing with PLC or industrial controller logic. The 5 nA maximum input off-leakage at +85 °C helps reduce errors from high-impedance sensor sources. Provide defined sensor returns and shield sensitive analog inputs from high-energy switching nodes.
Direkomendasikan
Sample-and-Hold Signal Conditioning
In a sample-and-hold circuit, the DG408CJ+ can select among several sensor outputs before the sampled signal is captured by a capacitor and amplifier. Its 100 ohm maximum on-resistance limits the source impedance seen by the hold capacitor, while the 8 ohm maximum channel matching improves consistency between successive measurements. The 15 pC maximum charge injection specification must be considered when sampling small signals, because the resulting transient appears at the common output. Use a larger hold capacitor or an acquisition-time extension when the signal amplitude is low.
Direkomendasikan
Audio and Instrumentation Signal Routing
The DG408CJ+ can route multiple balanced or unbalanced audio test sources to a shared analyzer channel. Its low maximum on-resistance preserves signal amplitude, and the 8 ohm maximum channel matching keeps level differences small when comparing channels. The TTL/CMOS address interface works with common digital controllers, while the enable function provides a controlled shutdown state between measurements. For low-level audio signals, minimize ground-loop impedance and keep the common output trace away from digital return currents.
Direkomendasikan
Programmable Signal Conditioning
The DG408CJ+ enables programmable gain, filter, and calibration networks by routing one of eight external components into a shared analog path. A microcontroller can drive the three address lines and enable input using standard CMOS logic levels, allowing remote configuration of test fixtures. Matching of 8 ohm maximum and flatness of 9 ohm maximum limit resistance-induced gain errors across the switching network. Keep relay or relay-driver transitions away from the high-impedance mux output to avoid injecting noise into the selected path.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DG408CJ+ — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DG408CJ | DG408DJ+ | DG408AK/883B |
|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 / CDIP-16 variant - confirm mechanical fit |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | 8:1 single-ended | 8:1 single-ended | 8:1 single-ended | 8:1 single-ended |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels |
| On-Resistance | 100 ohm maximum | 100 ohm maximum | 100 ohm maximum | 100 ohm maximum |
| Charge Injection | 15 pC maximum | 15 pC maximum | 15 pC maximum | 15 pC maximum |
| Single-Supply Voltage Range | +5 V to +30 V | +5 V to +30 V | +5 V to +30 V | +5 V to +30 V |
| Dual-Supply Voltage Range | ±5 V to ±20 V | ±5 V to ±20 V | ±5 V to ±20 V | ±5 V to ±20 V |
| Input Off-Leakage Current | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C |
| ESD Protection | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 |
| Logic Compatibility | TTL/CMOS compatible | TTL/CMOS compatible | TTL/CMOS compatible | TTL/CMOS compatible |
Diferensiator Kunci
- Guaranteed channel matching and flatness (vsDG408CJ)
- Broad single- and dual-supply operating range (vsDG408DJ+)
- Low charge injection for switched analog signals (vsDG408AK/883B)
- High-voltage ESD protection (vsDG408CJ)
Catatan Desain
Treat the DG408CJ+ common output as a switched node with 15 pC maximum charge injection. After changing an address, allow the acquisition system to settle before taking a measurement, especially when the source impedance is high or the sampled signal is small. Disabling the mux during address transitions can reduce feedthrough, but confirm that the required measurement timing still accommodates the switching interval.
Route the common output as a short analog trace and connect the multiplexer ground pins close to the measurement amplifier's reference network. Keep high-current switching paths and digital return currents away from the analog inputs. Because the specified channel-matching and flatness limits describe the device itself, board leakage and copper contamination can still dominate errors when measuring very high-impedance sources.
Use either the single +5 V to +30 V range or the dual ±5 V to ±20 V range consistently for the address thresholds and analog signal amplitude. Decouple the supply pins with local ceramic and bulk capacitance, and avoid placing the through-hole DIP adjacent to switching-power components. The device consumes no more than 1.25 mW, so thermal design is rarely the limiting factor.
Do not assume every DG408 ordering suffix has the same temperature grade or mechanical variant. Confirm that the selected part is a PDIP-16 configuration, verify the address and enable truth table, and check that the maximum input and output voltages remain inside the chosen supply range. Substituting a CDIP, SOIC, or narrow-versus-wide PDIP variant can create assembly or clearance problems.
Informasi Konformitas
The + ordering suffix identifies the current Analog Devices ordering form, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was published in the cited product listings. The device is an industrial and commercial analog interface IC rather than an automotive-qualified AEC-Q100 device.