Analog Devices

DG408CJ+ - 8:1 CMOS Analog Multiplexer | Analog Devices

料号: DG408CJ+ ✓ 量产中
+5 V to +30 V Vdss 5 nA maximum at +85 °C Id 100 ohm maximum Rds(on) 16-pin PDIP Package
最小起订量: 1 |

DG408CJ+ 概述

The Analog Devices DG408CJ+ is an improved 8-channel, single-ended CMOS analog multiplexer with one common output, packaged in a 16-pin PDIP. It selects one of eight analog inputs using three address inputs and an enable input, with a maximum on-resistance of 100 ohm. The device operates from a single +5 V to +30 V supply or from dual ±5 V to ±20 V supplies.

An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output terminal. The DG408CJ+ belongs to the broader analog switch and multiplexer family, where CMOS construction provides low power consumption, TTL/CMOS-compatible address controls, and bidirectional signal conduction. Unlike a mechanical rotary switch, it can change channels electronically while maintaining a defined low on-resistance.

Key electrical features include guaranteed matching between channels of 8 ohm maximum and on-resistance flatness of 9 ohm maximum across the specified signal range. Charge injection is limited to 15 pC maximum, while input off-leakage current is specified at 5 nA maximum at +85 °C. Rail-to-rail signal handling, ESD protection greater than 2000 V per MIL-STD-883 Method 3015.7, and low power consumption of 1.25 mW maximum support precision and instrumentation applications.

The device uses three binary address lines to select one of eight channels. A low enable level places the multiplexer in shutdown mode, reducing power consumption and isolating the common output. Address and enable inputs accept TTL/CMOS logic levels, allowing direct control from common microcontrollers, FPGAs, and data-acquisition systems. The common output and individual inputs support analog signals referenced to the applicable positive or negative supply rails.

Typical uses include multimeter and automated test equipment input switching, data-acquisition systems, industrial process measurement, sample-and-hold networks, and analog signal routing. The DG408CJ+ is especially useful when eight measurement sources must reach a shared amplifier, converter, or instrumentation amplifier while keeping channel resistance and injection error tightly controlled.

Designers should confirm the supply configuration, logic thresholds, and signal amplitude before layout. Keep analog traces short, provide a stable ground reference, and use the pin-description table in the manufacturer data sheet when assigning PCB tracks. Allow settling time after changing the address or enable state because charge injection and parasitic capacitance can produce a transient step on the common output.

直接替换替代料: DG408CJ+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: DG408CJ+ (相同外形与封装尺寸) ——差异在于 Input Off-Leakage Current, Logic Compatibility, Mounting Type, Multiplexer Configuration, On-Resistance.

Analog Devices
Input Off-Leakage Current: Less than 5 nA at 85°C
Logic Compatibility: TTL/CMOS compatible channel selection
Mounting Type: Through-hole dual in-line package
对比 DG408CJ+ →

DG408CJ

✅ 直接替换
📦 PDIP-16
Same 8:1 architecture, 100 ohm maximum on-resistance and 16-pin PDIP footprint; ordering suffix differs by 0%, while lead-free status and temperature grade must be confirmed.

📋 参考替代料(不在目录中)

DG408DJ+

✅ 直接替换
Analog Devices
📦 PDIP-16
8-channel single-ended CMOS analog multiplexer · 8:1 · 100 ohm · 8 channels · 3 binary inputs: A0, A1, A2 · 15 pC · Less than 5 nA at 85°C · Bidirectional

联系询价

查看数据手册 →

DG408AK/883B

✅ 直接替换
📦 PDIP-16
Same 8:1 multiplexer core and 100 ohm maximum on-resistance; the published comparison identifies a CDIP-16 versus PDIP-16 package difference, so board compatibility must be checked.

📋 参考替代料(不在目录中)

DG408CJ+ 规格参数

Multiplexer Configuration 8:1 single-ended analog multiplexer
Number of Channels 8 channels
Number of Functions 1 function
On-Resistance 100 ohm maximum
Channel Matching 8 ohm maximum
On-Resistance Flatness 9 ohm maximum over the specified signal range
Charge Injection 15 pC maximum
Input Off-Leakage Current 5 nA maximum at +85 °C
Single-Supply Voltage Range +5 V to +30 V
Dual-Supply Voltage Range ±5 V to ±20 V
Power Consumption 1.25 mW maximum
Signal Handling Rail-to-rail
Logic Compatibility TTL/CMOS compatible
ESD Protection Greater than 2000 V per MIL-STD-883 Method 3015.7
Process Technology CMOS
封装 16-pin PDIP
安装类型 Through-hole

DG408CJ+ 16-pin pdip 引脚配置指南

DG408CJ+(16-pin pdip 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

DG408CJ+ 的 16-pin pdip 封装引脚图

暂无详细引脚数据: DG408CJ+.

请参阅 数据手册 以查看完整引脚配置。

典型应用

DG408CJ+ 适用于 6 应用s: Multimeter and Automated Test Equipment, Data Acquisition Systems, Industrial Process Signal Routing, Sample-and-Hold Signal Conditioning, Audio and Instrumentation Signal Routing, Programmable Signal Conditioning.

🔧

Multimeter and Automated Test Equipment

The DG408CJ+ suits a digital multimeter or automated tester that must route eight input terminals to one measurement chain. Its 100 ohm maximum on-resistance is small relative to the input impedance of most digital voltmeters, while 8 ohm maximum channel matching helps limit gain errors when comparisons are made across channels. The TTL/CMOS-compatible address and enable inputs connect directly to test sequencer logic. Allow the common output to settle after each address change because the specified 15 pC maximum charge injection can create a transient step.

📊

Data Acquisition Systems

The DG408CJ+ can select among eight analog inputs in a multichannel data-acquisition system feeding a shared converter or instrumentation amplifier. The multiplexer minimizes channel-to-channel resistance variation to 8 ohm maximum and maintains on-resistance flatness within 9 ohm maximum over the specified signal range. Use the enable input to place the device in a shutdown state between conversions, and keep the common trace short to limit parasitic capacitance. A low-noise amplifier following the mux then establishes the system noise floor.

🏭

Industrial Process Signal Routing

The DG408CJ+ supports industrial process monitoring by routing pressure, temperature, or current-sense signals from multiple sensors to a common signal-conditioning amplifier. The rail-to-rail signal-handling capability allows operation close to the applicable supply rails, while TTL/CMOS-compatible control inputs simplify interfacing with PLC or industrial controller logic. The 5 nA maximum input off-leakage at +85 °C helps reduce errors from high-impedance sensor sources. Provide defined sensor returns and shield sensitive analog inputs from high-energy switching nodes.

📈

Sample-and-Hold Signal Conditioning

In a sample-and-hold circuit, the DG408CJ+ can select among several sensor outputs before the sampled signal is captured by a capacitor and amplifier. Its 100 ohm maximum on-resistance limits the source impedance seen by the hold capacitor, while the 8 ohm maximum channel matching improves consistency between successive measurements. The 15 pC maximum charge injection specification must be considered when sampling small signals, because the resulting transient appears at the common output. Use a larger hold capacitor or an acquisition-time extension when the signal amplitude is low.

🎧

Audio and Instrumentation Signal Routing

The DG408CJ+ can route multiple balanced or unbalanced audio test sources to a shared analyzer channel. Its low maximum on-resistance preserves signal amplitude, and the 8 ohm maximum channel matching keeps level differences small when comparing channels. The TTL/CMOS address interface works with common digital controllers, while the enable function provides a controlled shutdown state between measurements. For low-level audio signals, minimize ground-loop impedance and keep the common output trace away from digital return currents.

🔧

Programmable Signal Conditioning

The DG408CJ+ enables programmable gain, filter, and calibration networks by routing one of eight external components into a shared analog path. A microcontroller can drive the three address lines and enable input using standard CMOS logic levels, allowing remote configuration of test fixtures. Matching of 8 ohm maximum and flatness of 9 ohm maximum limit resistance-induced gain errors across the switching network. Keep relay or relay-driver transitions away from the high-impedance mux output to avoid injecting noise into the selected path.

What is the operating voltage of DG408CJ+?
The DG408CJ+ operates from a single supply of +5 V to +30 V or from dual supplies of ±5 V to ±20 V. According to the Analog Devices DG408 data sheet, the same device architecture supports both positive and negative analog signal rails within the selected supply limits. A single-supply design uses 0 V as the signal reference, while a dual-supply design permits bipolar input and output signals.
What is the on-resistance of DG408CJ+?
The DG408CJ+ has a maximum on-resistance of 100 ohm, and the selected switch conducts equally well in either direction. Analog Devices also guarantees channel-to-channel matching of 8 ohm maximum and on-resistance flatness of 9 ohm maximum over the specified signal range. These limits are important when the multiplexer feeds a high-impedance amplifier or a precision measurement chain.
How do I select one of the eight channels in DG408CJ+?
Three address inputs select one of eight channels, while the enable input controls whether the common output is connected to the selected input. The address and enable controls are TTL/CMOS compatible. Disable the device during address transitions when signal-integrity requirements demand it, and allow adequate settling time after changing the address because charge injection can create a transient voltage step.
Where can I download the DG408CJ+ datasheet PDF?
The official DG408 data sheet is available from the Analog Devices product page at https://www.analog.com/en/products/dg408.html, with a direct PDF copy also published at https://pdf.digi-electronics.com/pdf/1471/DG408CJ-datasheet.pdf. The document contains the truth tables, pin descriptions, supply configurations, electrical characteristics, and application information needed to evaluate the multiplexer.
Where can I find the DG408CJ+ pinout?
The DG408CJ+ pinout is shown in the pin-configuration and truth-table sections of the Analog Devices DG408 data sheet. The device has 16 pins in a PDIP package and includes three address inputs, an enable input, eight analog channels, and a common output. Use the manufacturer pin-description table when assigning PCB tracks because several analog terminals are grouped by function.
What is the best drop-in replacement for DG408CJ+?
The closest same-family drop-in options are the DG408CJ and DG408DJ+ in the 16-pin PDIP configuration, with the same 8:1 architecture and 100 ohm maximum on-resistance. The DG408DJ+ differs in temperature-grade suffix, while the DG408CJ differs by the lead-free ordering suffix. Confirm the required temperature grade and supply limits against the data sheet before replacing an existing design.
Can DG408DJ+ replace DG408CJ+ in an existing PCB?
Yes, the DG408DJ+ can serve as a pin-compatible replacement when the existing board uses the 16-pin PDIP footprint and the required temperature range matches. Both devices are 8:1 CMOS analog multiplexers with a 100 ohm maximum on-resistance, so the key electrical ratings are unchanged. The primary selection criterion is the ordering and temperature-grade suffix rather than the multiplexer architecture.
Is DG408CJ+ suitable for precision measurement systems?
The DG408CJ+ is suitable for precision measurement systems when channel resistance, leakage, and switching transients remain acceptable for the required accuracy. Its maximum channel matching of 8 ohm, flatness of 9 ohm, charge injection of 15 pC, and input off-leakage of 5 nA at +85 °C help limit measurement errors. A low-noise reference amplifier and settling time after channel selection are still required.
What can replace DG408CJ+?
The DG408CJ and DG408DJ+ are the closest drop-in replacements because they retain the 16-pin PDIP footprint, eight-channel 8:1 configuration, TTL/CMOS address interface, and 100 ohm maximum on-resistance. They differ in ordering or temperature-grade suffix rather than core switching performance. Verify the operating temperature, supply arrangement, and enable polarity in the manufacturer data sheet before substituting either device.
Is DG408CJ+ the same as DG408DJ+?
The DG408CJ+ and DG408DJ+ share the same 8:1 CMOS multiplexer architecture, 16-pin PDIP package, and principal electrical ratings of 100 ohm maximum on-resistance and 15 pC maximum charge injection. They are not identical ordering codes: the DG408DJ+ carries a different temperature-grade suffix. Choose based on the temperature range required by the instrument rather than on switching performance alone.
What are the key specifications of DG408CJ+ that engineers should know?
The DG408CJ+ is an 8-channel CMOS analog multiplexer with a 100 ohm maximum on-resistance, 8 ohm maximum channel matching, 15 pC maximum charge injection, and a 16-pin PDIP package. It accepts +5 V to +30 V single supply or ±5 V to ±20 V dual supply, uses TTL/CMOS-compatible control inputs, and provides ESD protection greater than 2000 V per MIL-STD-883 Method 3015.7.
Does DG408CJ+ require a heatsink?
No external heatsink is normally required for the DG408CJ+ because its maximum power consumption is 1.25 mW. The dominant concern in most analog measurement designs is signal accuracy rather than thermal management. Still, locate the PDIP away from hot regulator and power-stage areas, maintain airflow around the board, and verify the ambient temperature against the grade selected for the installation.
Where to buy DG408CJ+ online?
Use the Request a Quote form on this page to request DG408CJ+ pricing, stock confirmation, and a current delivery estimate. The form allows you to specify the required quantity, packaging preference, and shipment destination. Manufacturers and authorized distribution channels can then confirm the exact PDIP ordering code and lead time for your production schedule.
What is the price of DG408CJ+?
Current DG408CJ+ pricing is not static because it can vary with order quantity, market conditions, and authorized-channel availability. Submit the Request a Quote form on this page to obtain a current quotation for the quantity and package form you need. The same form can confirm stock, lead time, and shipment options without relying on an outdated listing price.
What is the lead time for DG408CJ+?
The current lead time depends on manufacturer inventory, the requested quantity, and the selected ordering channel. Request a quote through the form on this page to obtain a current lead-time confirmation for your production plan. When scheduling new production, allow additional time for incoming inspection and for any PCB changes required if your current assembly uses a different package variant.

工程参考数据: DG408CJ+ ——对比、设计指导和合规信息。

选型指南

Choose the DG408CJ+ when an eight-source analog measurement system needs a 16-pin PDIP multiplexer with guaranteed channel matching, low charge injection, and flexible single- or dual-supply operation. Choose the DG408DJ+ when its temperature-grade suffix matches the installation while retaining the same core multiplexer ratings and footprint. Choose the DG408CJ when the older ordering suffix is acceptable after checking temperature and lead-free requirements. Do not select the DG408AK/883B automatically for a PDIP board: its published comparison identifies a CDIP-16 configuration, so mechanical compatibility must be verified. Cross-brand substitutes were not established from a verified cross-reference listing, and the device is best used when its low on-resistance, 8 ohm channel matching, 15 pC charge injection, and rail-to-rail operation align with the measurement architecture.

与替代料对比

参数 本产品 DG408CJ DG408DJ+ DG408AK/883B
Package PDIP-16 PDIP-16 PDIP-16 PDIP-16 / CDIP-16 variant - confirm mechanical fit
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Multiplexer Configuration 8:1 single-ended 8:1 single-ended 8:1 single-ended 8:1 single-ended
Number of Channels 8 channels 8 channels 8 channels 8 channels
On-Resistance 100 ohm maximum 100 ohm maximum 100 ohm maximum 100 ohm maximum
Charge Injection 15 pC maximum 15 pC maximum 15 pC maximum 15 pC maximum
Single-Supply Voltage Range +5 V to +30 V +5 V to +30 V +5 V to +30 V +5 V to +30 V
Dual-Supply Voltage Range ±5 V to ±20 V ±5 V to ±20 V ±5 V to ±20 V ±5 V to ±20 V
Input Off-Leakage Current 5 nA maximum at +85 °C 5 nA maximum at +85 °C 5 nA maximum at +85 °C 5 nA maximum at +85 °C
ESD Protection Greater than 2000 V per MIL-STD-883 Method 3015.7 Greater than 2000 V per MIL-STD-883 Method 3015.7 Greater than 2000 V per MIL-STD-883 Method 3015.7 Greater than 2000 V per MIL-STD-883 Method 3015.7
Logic Compatibility TTL/CMOS compatible TTL/CMOS compatible TTL/CMOS compatible TTL/CMOS compatible

关键差异点

  • Guaranteed channel matching and flatness (对比 DG408CJ)
  • Broad single- and dual-supply operating range (对比 DG408DJ+)
  • Low charge injection for switched analog signals (对比 DG408AK/883B)
  • High-voltage ESD protection (对比 DG408CJ)

设计说明

Treat the DG408CJ+ common output as a switched node with 15 pC maximum charge injection. After changing an address, allow the acquisition system to settle before taking a measurement, especially when the source impedance is high or the sampled signal is small. Disabling the mux during address transitions can reduce feedthrough, but confirm that the required measurement timing still accommodates the switching interval.

Route the common output as a short analog trace and connect the multiplexer ground pins close to the measurement amplifier's reference network. Keep high-current switching paths and digital return currents away from the analog inputs. Because the specified channel-matching and flatness limits describe the device itself, board leakage and copper contamination can still dominate errors when measuring very high-impedance sources.

Use either the single +5 V to +30 V range or the dual ±5 V to ±20 V range consistently for the address thresholds and analog signal amplitude. Decouple the supply pins with local ceramic and bulk capacitance, and avoid placing the through-hole DIP adjacent to switching-power components. The device consumes no more than 1.25 mW, so thermal design is rarely the limiting factor.

Do not assume every DG408 ordering suffix has the same temperature grade or mechanical variant. Confirm that the selected part is a PDIP-16 configuration, verify the address and enable truth table, and check that the maximum input and output voltages remain inside the chosen supply range. Substituting a CDIP, SOIC, or narrow-versus-wide PDIP variant can create assembly or clearance problems.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The + ordering suffix identifies the current Analog Devices ordering form, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was published in the cited product listings. The device is an industrial and commercial analog interface IC rather than an automotive-qualified AEC-Q100 device.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

DG408CJ+ datasheet DG408CJ+ pinout DG408CJ+ datasheet pdf DG408CJ+ equivalent DG408CJ+ replacement DG408CJ+ cross reference DG408CJ+ vs DG408DJ+ DG408CJ+ PDIP-16 multiplexer DG408CJ+ 8 channel analog switch DG408CJ+ on-resistance DG408CJ+ supply voltage DG408CJ+ application circuit Analog Devices DG408CJ+ DG408CJ+ buy online DG408CJ+ price and stock

相关元器件 & 术语

Analog Devices DG408CJ+ DG408 DG408CJ DG408DJ+ DG408AK/883B CMOS analog multiplexer analog switch multiplexer 8:1 single-ended mux TTL/CMOS-compatible logic on-resistance channel matching charge injection input off-leakage current rail-to-rail signal handling PDIP-16 through-hole package MIL-STD-883 Method 3015.7 ESD protection data acquisition automated test equipment industrial process measurement sample-and-hold
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情