DG408CJ+ - 8:1 CMOS Analog Multiplexer | Analog Devices
MPN: DG408CJ+ ✓ Hoạt độngDG408CJ+ Tóm tắt
An analog multiplexer is a semiconductor switching network that connects one of several input terminals to a shared output terminal. The DG408CJ+ belongs to the broader analog switch and multiplexer family, where CMOS construction provides low power consumption, TTL/CMOS-compatible address controls, and bidirectional signal conduction. Unlike a mechanical rotary switch, it can change channels electronically while maintaining a defined low on-resistance.
Key electrical features include guaranteed matching between channels of 8 ohm maximum and on-resistance flatness of 9 ohm maximum across the specified signal range. Charge injection is limited to 15 pC maximum, while input off-leakage current is specified at 5 nA maximum at +85 °C. Rail-to-rail signal handling, ESD protection greater than 2000 V per MIL-STD-883 Method 3015.7, and low power consumption of 1.25 mW maximum support precision and instrumentation applications.
The device uses three binary address lines to select one of eight channels. A low enable level places the multiplexer in shutdown mode, reducing power consumption and isolating the common output. Address and enable inputs accept TTL/CMOS logic levels, allowing direct control from common microcontrollers, FPGAs, and data-acquisition systems. The common output and individual inputs support analog signals referenced to the applicable positive or negative supply rails.
Typical uses include multimeter and automated test equipment input switching, data-acquisition systems, industrial process measurement, sample-and-hold networks, and analog signal routing. The DG408CJ+ is especially useful when eight measurement sources must reach a shared amplifier, converter, or instrumentation amplifier while keeping channel resistance and injection error tightly controlled.
Designers should confirm the supply configuration, logic thresholds, and signal amplitude before layout. Keep analog traces short, provide a stable ground reference, and use the pin-description table in the manufacturer data sheet when assigning PCB tracks. Allow settling time after changing the address or enable state because charge injection and parasitic capacitance can produce a transient step on the common output.
Bộ thay thế dễ dàng lắp đặt cho DG408CJ+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DG408CJ+ (cùng hình factor và footprint) — khác nhau ở Input Off-Leakage Current, Logic Compatibility, Mounting Type, Multiplexer Configuration, On-Resistance.
DG408CJ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG408DJ+
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DG408AK/883B
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DG408CJ+ Thông số kỹ thuật
| Multiplexer Configuration | 8:1 single-ended analog multiplexer |
| Number of Channels | 8 channels |
| Number of Functions | 1 function |
| On-Resistance | 100 ohm maximum |
| Channel Matching | 8 ohm maximum |
| On-Resistance Flatness | 9 ohm maximum over the specified signal range |
| Charge Injection | 15 pC maximum |
| Input Off-Leakage Current | 5 nA maximum at +85 °C |
| Single-Supply Voltage Range | +5 V to +30 V |
| Dual-Supply Voltage Range | ±5 V to ±20 V |
| Power Consumption | 1.25 mW maximum |
| Signal Handling | Rail-to-rail |
| Logic Compatibility | TTL/CMOS compatible |
| ESD Protection | Greater than 2000 V per MIL-STD-883 Method 3015.7 |
| Process Technology | CMOS |
| Hộp | 16-pin PDIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân DG408CJ+ 16-pin pdip
Cấu hình chân cho DG408CJ+ (16-pin pdip gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DG408CJ+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DG408CJ+ phù hợp cho 6 Áp dụngs: Multimeter and Automated Test Equipment, Data Acquisition Systems, Industrial Process Signal Routing, Sample-and-Hold Signal Conditioning, Audio and Instrumentation Signal Routing, Programmable Signal Conditioning.
Multimeter and Automated Test Equipment
The DG408CJ+ suits a digital multimeter or automated tester that must route eight input terminals to one measurement chain. Its 100 ohm maximum on-resistance is small relative to the input impedance of most digital voltmeters, while 8 ohm maximum channel matching helps limit gain errors when comparisons are made across channels. The TTL/CMOS-compatible address and enable inputs connect directly to test sequencer logic. Allow the common output to settle after each address change because the specified 15 pC maximum charge injection can create a transient step.
Được đề xuất
Data Acquisition Systems
The DG408CJ+ can select among eight analog inputs in a multichannel data-acquisition system feeding a shared converter or instrumentation amplifier. The multiplexer minimizes channel-to-channel resistance variation to 8 ohm maximum and maintains on-resistance flatness within 9 ohm maximum over the specified signal range. Use the enable input to place the device in a shutdown state between conversions, and keep the common trace short to limit parasitic capacitance. A low-noise amplifier following the mux then establishes the system noise floor.
Được đề xuất
Industrial Process Signal Routing
The DG408CJ+ supports industrial process monitoring by routing pressure, temperature, or current-sense signals from multiple sensors to a common signal-conditioning amplifier. The rail-to-rail signal-handling capability allows operation close to the applicable supply rails, while TTL/CMOS-compatible control inputs simplify interfacing with PLC or industrial controller logic. The 5 nA maximum input off-leakage at +85 °C helps reduce errors from high-impedance sensor sources. Provide defined sensor returns and shield sensitive analog inputs from high-energy switching nodes.
Được đề xuất
Sample-and-Hold Signal Conditioning
In a sample-and-hold circuit, the DG408CJ+ can select among several sensor outputs before the sampled signal is captured by a capacitor and amplifier. Its 100 ohm maximum on-resistance limits the source impedance seen by the hold capacitor, while the 8 ohm maximum channel matching improves consistency between successive measurements. The 15 pC maximum charge injection specification must be considered when sampling small signals, because the resulting transient appears at the common output. Use a larger hold capacitor or an acquisition-time extension when the signal amplitude is low.
Được đề xuất
Audio and Instrumentation Signal Routing
The DG408CJ+ can route multiple balanced or unbalanced audio test sources to a shared analyzer channel. Its low maximum on-resistance preserves signal amplitude, and the 8 ohm maximum channel matching keeps level differences small when comparing channels. The TTL/CMOS address interface works with common digital controllers, while the enable function provides a controlled shutdown state between measurements. For low-level audio signals, minimize ground-loop impedance and keep the common output trace away from digital return currents.
Được đề xuất
Programmable Signal Conditioning
The DG408CJ+ enables programmable gain, filter, and calibration networks by routing one of eight external components into a shared analog path. A microcontroller can drive the three address lines and enable input using standard CMOS logic levels, allowing remote configuration of test fixtures. Matching of 8 ohm maximum and flatness of 9 ohm maximum limit resistance-induced gain errors across the switching network. Keep relay or relay-driver transitions away from the high-impedance mux output to avoid injecting noise into the selected path.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DG408CJ+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DG408CJ | DG408DJ+ | DG408AK/883B |
|---|---|---|---|---|
| Package | PDIP-16 | PDIP-16 | PDIP-16 | PDIP-16 / CDIP-16 variant - confirm mechanical fit |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Multiplexer Configuration | 8:1 single-ended | 8:1 single-ended | 8:1 single-ended | 8:1 single-ended |
| Number of Channels | 8 channels | 8 channels | 8 channels | 8 channels |
| On-Resistance | 100 ohm maximum | 100 ohm maximum | 100 ohm maximum | 100 ohm maximum |
| Charge Injection | 15 pC maximum | 15 pC maximum | 15 pC maximum | 15 pC maximum |
| Single-Supply Voltage Range | +5 V to +30 V | +5 V to +30 V | +5 V to +30 V | +5 V to +30 V |
| Dual-Supply Voltage Range | ±5 V to ±20 V | ±5 V to ±20 V | ±5 V to ±20 V | ±5 V to ±20 V |
| Input Off-Leakage Current | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C | 5 nA maximum at +85 °C |
| ESD Protection | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 | Greater than 2000 V per MIL-STD-883 Method 3015.7 |
| Logic Compatibility | TTL/CMOS compatible | TTL/CMOS compatible | TTL/CMOS compatible | TTL/CMOS compatible |
Bảo phân biệt quan trọng
- Guaranteed channel matching and flatness (vsDG408CJ)
- Broad single- and dual-supply operating range (vsDG408DJ+)
- Low charge injection for switched analog signals (vsDG408AK/883B)
- High-voltage ESD protection (vsDG408CJ)
Ghi chú thiết kế
Treat the DG408CJ+ common output as a switched node with 15 pC maximum charge injection. After changing an address, allow the acquisition system to settle before taking a measurement, especially when the source impedance is high or the sampled signal is small. Disabling the mux during address transitions can reduce feedthrough, but confirm that the required measurement timing still accommodates the switching interval.
Route the common output as a short analog trace and connect the multiplexer ground pins close to the measurement amplifier's reference network. Keep high-current switching paths and digital return currents away from the analog inputs. Because the specified channel-matching and flatness limits describe the device itself, board leakage and copper contamination can still dominate errors when measuring very high-impedance sources.
Use either the single +5 V to +30 V range or the dual ±5 V to ±20 V range consistently for the address thresholds and analog signal amplitude. Decouple the supply pins with local ceramic and bulk capacitance, and avoid placing the through-hole DIP adjacent to switching-power components. The device consumes no more than 1.25 mW, so thermal design is rarely the limiting factor.
Do not assume every DG408 ordering suffix has the same temperature grade or mechanical variant. Confirm that the selected part is a PDIP-16 configuration, verify the address and enable truth table, and check that the maximum input and output voltages remain inside the chosen supply range. Substituting a CDIP, SOIC, or narrow-versus-wide PDIP variant can create assembly or clearance problems.
Thông tin tuân thủ
The + ordering suffix identifies the current Analog Devices ordering form, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was published in the cited product listings. The device is an industrial and commercial analog interface IC rather than an automotive-qualified AEC-Q100 device.