DG413DY+T - Quad SPST Analog Switch | Maxim Integrated
MPN: DG413DY+T ✓ AktifDG413DY+T Ringkasan
An analog switch is an electronic routing component that connects or disconnects signal paths under digital control. The DG413DY+T belongs to the broader multiplexer and demultiplexer hierarchy within interface ICs. Its CMOS control inputs are compatible with TTL and CMOS logic, allowing the four channels to be operated independently from a microcontroller, FPGA, or test-system controller.
Key features include low on-resistance matching between switches, with a maximum variation of 3 ohms, and guaranteed on-resistance flatness across the signal range of up to 4 ohms. The device also features low charge injection, low power consumption, and ESD tolerance of at least 2000 V per Method 3015.7. These characteristics help preserve signal integrity when the same analog path is shared by several measurement or control channels.
The DG413DY+T is designed around a monolithic quad-SPST architecture. Each switch uses separate control and signal terminals, making it possible to route one source to one destination or disconnect a signal completely. The low leakage specification of 250 pA maximum helps limit unwanted coupling between high-impedance nodes when a switch is open. The 16-SOIC package supports conventional surface-mount PCB assembly while keeping the four channels in a compact layout.
Typical uses include battery-powered test equipment, data-acquisition systems, analog signal conditioning, sample-and-hold circuits, communication routing, and industrial control systems. The device is especially useful when a design needs flexible selection between normally open and normally closed paths, controlled isolation of unused inputs, or independent switching of several low-frequency analog signals.
For PCB design, keep control traces away from high-impedance signal nodes and route analog inputs and outputs with short, symmetric traces. Confirm the supply voltage, logic thresholds, signal range, and operating temperature against the manufacturer datasheet before production release. This page combines device specifications, sourcing guidance, compatible alternatives, and practical analog-switch design considerations for faster engineering evaluation.
Alternatif penggantian untuk DG413DY+T — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DG413DY+T (sama faktor bentuk dan footprint) — berbeda di dalam Package, Number of Channels, Number of Circuits, Operating Temperature.
DG413DY-E3
✅ Drop-InKontak untuk harga
Lihat Datasheet →DG413DY-T
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG413DY-T1
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG413DY-E3
✅ Drop-InKontak untuk harga
Lihat Datasheet →DG413DY+
✅ Drop-InKontak untuk harga
Lihat Datasheet →DG413DY+T Rating Maksimal & Karakteristik Listrik
| Number of Circuits | 4 circuits |
| Switch Configuration | 4 independent SPST switches |
| Multiplexer Configuration | 1:1 |
| On-Resistance | 35 ohm |
| On-Resistance Matching | 3 ohm maximum |
| On-Resistance Flatness | 4 ohm maximum variation |
| Leakage Current | 250 pA maximum |
| ESD Tolerance | 2000 V minimum per Method 3015.7 |
| Logic Input Levels | TTL and CMOS compatible |
| Suhu Kerja | -40 °C to +85 °C |
| Paket | 16-SOIC, 0.154 inch / 3.90 mm body width |
| Tipe Mounting | Surface mount |
| Packaging | Bulk |
| Product Status | Active |
| RoHS Compliance | Compliant |
| Jumlah Pin | 16 pins |
DG413DY+T 16-soic, 0.154 inch / 3.90 mm body width Diamant Konfigurasi Panduan
Konfigurasi pin untuk DG413DY+T (16-soic, 0.154 inch / 3.90 mm body width pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DG413DY+T.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DG413DY+T cocok untuk 6 aplikasis: Battery-Powered Test and Measurement Systems, Data Acquisition and Sensor Multiplexing, Analog Signal Conditioning, Communication and Test Signal Routing, Industrial Control Signal Isolation, Programmable Instrumentation and Calibration.
Battery-Powered Test and Measurement Systems
The DG413DY+T fits portable measurement equipment where four analog paths must be selected under digital control. Its four independent SPST channels provide normally open and normally closed contacts, while the 35 ohm on-resistance is suitable for low-frequency signal routing rather than high-impedance precision networks. The manufacturer’s family description highlights low power consumption, low charge injection, and low leakage, which help preserve measurement stability when the instrument switches between sensors or calibration points. Place the device close to the source and destination nodes, use a controlled reference ground, and confirm the actual signal bandwidth and settling behavior in the system prototype.
Direkomendasikan
Data Acquisition and Sensor Multiplexing
The DG413DY+T is useful in data-acquisition front ends that require independent routing among several sensor or conditioning nodes. Four separate SPST channels can connect one source to one destination at a time, and the 250 pA maximum leakage specification helps limit unwanted interaction in high-impedance circuits. The 3 ohm maximum matching between switches and 4 ohm maximum flatness variation are valuable when channel resistance must not introduce large gain differences. Designers should still verify input overdrive, bandwidth, charge injection, and off leakage against the manufacturer datasheet before using the switch directly at the sensor input.
Direkomendasikan
Analog Signal Conditioning
The DG413DY+T can route analog signals around amplifiers, filters, or calibration elements in a signal-conditioning board. Its 35 ohm on-resistance adds a finite insertion resistance, making the device most appropriate where the source impedance and downstream amplifier impedance are compatible with that load. The low on-resistance matching and flatness help maintain consistent behavior across the four channels, while TTL- and CMOS-compatible control allows direct interfacing with common digital controllers. Keep traces short and use a solid ground reference to limit injection from control signals. Validate settling time and channel-to-channel delay when precise measurement timing is required.
Direkomendasikan
Communication and Test Signal Routing
The DG413DY+T can provide programmable routing in communication equipment, automated test fixtures, and signal-interface boards. Its four independent normally open/normally closed SPST channels allow a controller to connect, isolate, or disconnect multiple lines without changing the external package footprint. The 16-SOIC format is convenient for conventional surface-mount assembly, and the 2000 V minimum ESD tolerance provides a defined protection target under Method 3015.7. Designers should still protect the signal path against excessive overvoltage, observe the specified supply limits, and verify that control transitions do not create unacceptable coupling on sensitive nodes.
Direkomendasikan
Industrial Control Signal Isolation
The DG413DY+T can isolate or connect control and instrumentation lines in industrial electronics while keeping the switching element compact. The independently controlled SPST channels are useful when each line needs a different on/off state, and the normally closed contacts provide a defined fallback path during power transitions where appropriate. The device operates across a -40 °C to +85 °C range, making it suitable for many industrial temperature environments, subject to the complete electrical ratings. Use the control inputs only from compatible logic levels and confirm whether the application requires fail-safe default states, isolation resistance, or reinforced spacing beyond the device specifications.
Direkomendasikan
Programmable Instrumentation and Calibration
The DG413DY+T supports programmable signal paths in calibration and instrumentation equipment where a controller selects among external references, injects test signals, or disconnects unused inputs. Its low charge injection is relevant when switching networks around sensitive measurement nodes, while low power consumption helps portable and compact systems. Four channels can be managed with standard digital control, and the SOIC-16 package simplifies assembly where a larger multiplexer would be unnecessary. For best results, establish a repeatable settling period after each switch command, use low-leakage surrounding nodes when appropriate, and verify that the 35 ohm path resistance is acceptable for the selected source and load.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DG413DY+T — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DG413DY | DG413DY-T | DG413DY-T1 | DG413DY-E3 | DG413DY+ |
|---|---|---|---|---|---|---|
| Package | 16-SOIC, 0.154 inch / 3.90 mm width | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Maxim Integrated | Renesas Electronics | Renesas Electronics | Vishay Siliconix | Vishay Siliconix | Maxim Integrated |
Diferensiator Kunci
- Four independently controlled SPST channels in one 16-SOIC package (vsTS5A23157)
- Defined leakage specification for high-impedance routing (vsDG413DY-T1)
- Low on-resistance variation across the signal range (vsDG413DY-E3)
Catatan Desain
Treat each SPST path as a 35 ohm series resistance and include that resistance in the source-to-load calculation. For high-impedance nodes, use short traces, a continuous ground reference, and a defined settling interval after switching. The manufacturer's family specification gives 3 ohm maximum matching between switches and 4 ohm maximum on-resistance flatness, which are useful checks when channel-dependent gain error matters.
Route the four analog channels with consistent geometry and keep the SOIC-16 control pins away from sensitive analog traces where practical. Use a quiet analog ground connection and place supply-decoupling capacitance close to the device pins according to the manufacturer layout guidance. Because the exact pin names and NC locations are not reproduced here, use the pin-description table in the manufacturer datasheet when assigning tracks.
Do not substitute a dual SPDT device for the DG413DY+T without redesigning the board. The TS5A23157, for example, has a different switch architecture and control arrangement. Also verify supply voltage, logic thresholds, input overdrive, leakage, and absolute maximum ratings before production; the same SOIC outline alone does not guarantee electrical compatibility.
Informasi Konformitas
RoHS compliance is identified in the cross-reference information. Other environmental declarations require confirmation for the exact order code and manufacturer.