DS90C363MTDX - 18-Bit 65MHz LVDS FPD-Link Transmitter | Texas Instruments
MPN: DS90C363MTDX ✓ AktifDS90C363MTDX Ringkasan
An LVDS transmitter is a semiconductor interface device that converts parallel digital data into low-voltage differential signals. Differential signaling represents each bit with two complementary conductors, reducing sensitivity to common-mode noise and allowing reliable high-speed communication over board-level interconnects. In the broader hierarchy, the DS90C363MTDX belongs to the LVDS transmitter class, flat-panel display interface family, interface IC category, and semiconductor product category.
The key features of this device include an 18-bit programmable data width, a 65 MHz operating specification, a 3.3 V supply, and FPD-Link operation. These characteristics allow the transmitter to carry display pixel data while reducing the number of interconnects required by conventional single-ended parallel signaling. Its 48-terminal TSSOP package also provides a compact surface-mount implementation for display-controller and interface boards.
The transmitter is designed for parallel-to-differential conversion in flat-panel display systems. Its architecture accepts digital pixel information and serializes it onto an LVDS link, while the receiver and display timing system recover the transmitted data at the opposite end. The reported 1,300 Mbps data rate corresponds to the high-speed serialized link capability, whereas the 18-bit input width describes the parallel pixel payload presented to the transmitter.
Typical uses include digital flat-panel monitors, industrial display controllers, automotive display interfaces, medical display equipment, video-processing systems, and embedded graphics platforms. It is particularly appropriate when a system requires an LVDS FPD-Link transmitter rather than a generic low-speed differential driver, and when the source device must transfer an 18-bit pixel bus into a compact high-speed differential channel.
The primary layout consideration is placement of the transmitter close to the LVDS output connector and the source graphics logic. Keep the differential pair routed as a controlled-impedance pair, minimize stub lengths, and follow the manufacturer's pin-description and reference-layout guidance. Confirm output timing, receiver compatibility, connector pin assignment, and panel-specific initialization requirements before releasing a production design.
This product record combines manufacturer identification, package and interface specifications, sourcing guidance, application fit, and a constrained drop-in comparison. It also highlights the important distinction between the 18-bit parallel payload, the 65 MHz operating point, and the 1,300 Mbps serialized LVDS link so engineers can evaluate bandwidth, board constraints, and receiver interoperability consistently.
Alternatif penggantian untuk DS90C363MTDX — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DS90C363MTDX (sama faktor bentuk dan footprint) — berbeda di dalam Product Type.
DS90C363MTD
✅ Drop-InKontak untuk harga
Lihat Datasheet →DS90C363MTDX Spesifikasi
| Product Type | Programmable LVDS transmitter |
| Tegangan Pemuat | 3.3 V |
| Data Width | 18 bit |
| Frekuensi Bawah Maximum | 65 MHz |
| Serialized Data Rate | 1,300 Mbps |
| Interface Standard | FPD-Link |
| Logic Voltage | 0.45 V |
| Package Type | 48-pin TSSOP |
| Terminal Count | 48 terminals |
| Terminal Form | Gull wing |
| Mounting Technology | Surface mount |
| Temperature Grade | Industrial |
DS90C363MTDX 48-pin tssop Diamant Konfigurasi Panduan
Konfigurasi pin untuk DS90C363MTDX (48-pin tssop pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DS90C363MTDX.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DS90C363MTDX cocok untuk 6 aplikasis: Digital Flat-Panel Monitor Interface, Industrial Display Controller, Automotive Display Link, Medical Diagnostic Display, Video Processing System, Embedded Graphical Control Panel.
Digital Flat-Panel Monitor Interface
The DS90C363MTDX fits a digital flat-panel monitor that receives parallel pixel data from a graphics controller and requires a compact LVDS link. Its 18-bit parallel input matches the identified pixel payload, while the 65 MHz operating specification supports the associated display timing. Placing the transmitter close to the source logic reduces routing burden, and the reported 1,300 Mbps link rate provides the throughput needed for FPD-Link transmission. The display engine, timing generator, connector, and receiver must remain synchronized to the same clock and initialization sequence.
Direkomendasikan
Industrial Display Controller
Industrial display systems benefit from the DS90C363MTDX because it combines an 18-bit parallel input with a high-speed differential output in a 48-pin TSSOP package. The 3.3 V interface level supports integration with compatible digital display-controller logic, and the 65 MHz specification provides a defined timing target for pixel-clock design. Use controlled-impedance routing for the LVDS pair and verify panel timing margins across temperature, power-supply tolerance, and cable length before production.
Direkomendasikan
Automotive Display Link
The DS90C363MTDX can support compatible automotive display architectures that use an 18-bit FPD-Link transmitter and 3.3 V interface. Its 65 MHz operating specification and reported 1,300 Mbps serialized rate suit high-resolution display links, while the TSSOP package simplifies board assembly. The final design must confirm the applicable automotive qualification for the exact orderable variant, as well as display power sequencing, transient immunity, cable construction, connector retention, and operation over the complete vehicle temperature range.
Direkomendasikan
Medical Diagnostic Display
A medical diagnostic display can use the DS90C363MTDX when the display controller requires an 18-bit parallel pixel input and a compact high-speed LVDS output. The 65 MHz operating point and 1,300 Mbps reported link rate provide a clear bandwidth basis for interface timing, while differential signaling can reduce sensitivity to common-mode noise in multi-board systems. Designers must still validate image timing, isolation requirements, grounding, cable routing, fault behavior, and regulatory requirements for the complete display system rather than the transmitter alone.
Direkomendasikan
Video Processing System
The DS90C363MTDX is applicable inside a video-processing system that converts an 18-bit parallel pixel stream into an FPD-Link LVDS transmission for a downstream display. Its 3.3 V operation and defined 65 MHz timing allow the transmitter to be placed at the output boundary of an image-processing pipeline. Account for pipeline latency when defining display timing, and verify that all source signals meet the electrical requirements before serialization. A short, impedance-controlled differential route directly to the connector improves implementation predictability.
Direkomendasikan
Embedded Graphical Control Panel
Embedded graphical control panels can use the DS90C363MTDX when their controller exposes an 18-bit pixel bus and the selected screen accepts compatible FPD-Link signaling. The device combines a 3.3 V supply, 65 MHz operating specification, and 48-pin TSSOP package for a compact panel-link implementation. Integration should include a deliberate startup sequence, defined clock generation, receiver compatibility checks, and connector pin verification. Differential trace geometry, ground continuity, and enclosure grounding require system-level review to preserve signal integrity.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DS90C363MTDX — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DS90C363MTD |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 48-pin TSSOP | 48-pin TSSOP |
| Product Type | Programmable LVDS transmitter | Programmable LVDS transmitter |
| Supply Voltage | 3.3 V | 3.3 V |
| Data Width | 18 bit | 18 bit |
| Maximum Clock Frequency | 65 MHz | 65 MHz |
| Interface Standard | FPD-Link | FPD-Link |
Diferensiator Kunci
- Combines an 18-bit parallel interface with a 1,300 Mbps serialized LVDS link (vsDS90C363MTD)
- Uses a 48-pin TSSOP surface-mount interface package (vsDS90C363MTD)
- Designed specifically for programmable flat-panel display transmission (vsDS90C363MTD)
Catatan Desain
Route the LVDS differential pair as a controlled-impedance pair from the DS90C363MTDX outputs to the display connector. Minimize vias, branch stubs, and changes in reference-plane geometry. Keep the pair away from switching-power nodes and high-slew-rate clock traces. Obtain the manufacturer's reference layout and package pin table before assigning the connector because the physical power, ground, control, and differential-output positions must match the selected board design.
Follow the manufacturer's recommended input, output, and bypass-capacitor arrangement for the 3.3 V supply and each supply terminal. Place high-frequency bypass capacitance close to the device's power pins and keep the return path continuous. Validate supply tolerance, startup sequencing, and voltage levels at the pins because the transmitter converts parallel data into a differential link only when the source and receiver timing remain synchronized.
Verify the 18-bit source timing, pixel-clock relationship, and LVDS receiver requirements before enabling the link. The 65 MHz operating specification and reported 1,300 Mbps serialized rate should be used as design checks rather than assumed guarantees for every panel combination. Review rise and fall times, clock jitter, skew between data and clock, connector loss, and cable length with the receiver and panel vendors.
Do not select the device solely because both parts are described as 48-pin TSSOP transmitters. Confirm the exact ordering suffix, pin functions, initialization requirements, receiver compatibility, and shipping form before releasing a replacement order. Also distinguish the 18-bit parallel payload from the 65 MHz clock specification and the 1,300 Mbps serialized link rate; using these parameters interchangeably can produce timing errors or an incorrect bandwidth estimate.
Informasi Konformitas
The manufacturer product page and distributor listings do not explicitly state the requested compliance fields for this orderable MPN. Verify them on the Texas Instruments product page or in the manufacturer datasheet before regulated production release.