DSPIC30F6013T-30I/PF - 16-bit DSC, 132KB Flash, 30MIPs | Microchip
MPN: DSPIC30F6013T-30I/PF ✗ Akhir HidupDSPIC30F6013T-30I/PF Ringkasan
What is a Digital Signal Controller? A DSC is a hybrid architecture that combines microcontroller (MCU) determinism with digital signal processor (DSP) throughput. In the broader hierarchy, DSCs sit between general-purpose MCUs and full DSPs, integrating multiply-accumulate (MAC) units, barrel shifters, and dual data RAM banks to execute control loops and signal processing on a single chip. The dsPIC30F specifically adds 40-bit accumulators and DSP-specific addressing modes for applications such as motor control, audio processing, and power conversion.
Key features of the DSPIC30F6013T-30I/PF include a 16-bit data path with modified Harvard architecture, 12-bit ADC with up to 16 channels, multiple communication peripherals (UART, SPI, I2C, CAN), PWM modules suitable for three-phase motor control, and a wide operating voltage range from 2.5V to 5.5V. The 30 MIPs throughput is achieved through a 4-cycle instruction pipeline that still maintains deterministic interrupt latency.
The DSP engine supports fractional (Q15) and integer arithmetic with single-cycle 16x16 MAC, allowing the implementation of digital filters (FIR/IIR), PID controllers, FFT kernels, and complex sensor-fusion routines without external DSP hardware. The Flash-based program memory supports in-circuit self-programming and ICE/debug via the standard 2-wire Microchip ICD interface, simplifying field firmware updates.
Typical applications include industrial motor drives (BLDC, PMSM, ACIM), automotive body controllers, digital power conversion (UPS, solar inverters), sensor signal conditioning, and low-cost audio effect processors. The 80-pin TQFP package exposes enough I/O for direct three-phase inverter drive without external logic.
When designing with this DSC, allocate sufficient Flash for both the application code and DSP coefficient tables; budget roughly 4-6 KB for a typical motor-control firmware with field-oriented control (FOC). Use the dsPIC30F Family Reference Manual (DS70046) for peripheral programming rather than relying solely on the device-specific datasheet.
This page synthesizes distributor stock signals, drop-in same-family variants, and application-level design guidance beyond the device datasheet, giving procurement and embedded engineers a faster path to BOM decisions and code bring-up.
Alternatif penggantian untuk DSPIC30F6013T-30I/PF — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian DSPIC30F6013T-30I/PF (sama faktor bentuk dan footprint) — berbeda di dalam Package, ADC, RoHS Status, Operating Temperature, Core Architecture.
DSPIC30F6014T-30I/PF
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
DSPIC30F6013AT-30I/PT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DSPIC30F6013A-30I/PF
✅ Drop-InKontak untuk harga
Lihat Datasheet →DSPIC30F6013A-30I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →DSPIC30F6012AT-30I/PF
✅ Drop-InKontak untuk harga
Lihat Datasheet →DSPIC30F6011AT-30I/PT
✅ Drop-InKontak untuk harga
Lihat Datasheet →DSPIC30F6013T-30I/PF Rating Maksimal & Karakteristik Listrik
| Core Architecture | dsPIC30F 16-bit DSC (modified Harvard) |
| Instruction Set | 16-bit RISC with DSP extensions |
| Maximum CPU Speed | 30 MIPS at 30 MHz |
| Program Memory | 132 KB (44K x 24) Flash |
| Data RAM | 6 KB (6144 bytes) |
| Operating Voltage | 2.5 V to 5.5 V |
| Paket | 80-pin TQFP (14x14 mm, 1.0 mm height) |
| Tipe Mounting | Surface Mount |
| Suhu Kerja | -40C to +85C (Industrial) |
| Status RoHS | ROHS3 Compliant |
| Programming/Debug | ICD via 2-wire interface (PGEDx/PGECx) |
| Packaging | Tape & Reel (TR) |
| Series | dsPIC30F |
Konfigurasi Pin DSPIC30F6013T-30I/PF
| Pin produk 1 | AN0 — Analog input 0 / VREF+ |
| Pin produk 2 | AN1 — Analog input 1 |
| Pin produk 3 | AN2 — Analog input 2 |
| Pin produk 4 | AN3 — Analog input 3 |
| Pin produk 5 | AN4 — Analog input 4 |
| Pin produk 6 | AN5 — Analog input 5 |
| Pin produk 7 | AN6 — Analog input 6 |
| Pin produk 8 | AN7 — Analog input 7 |
| Pin produk 9 | VDD — Core logic supply (2.5V-5.5V) |
| Pin produk 10 | VSS — Ground |
| Pin produk 11 | OSC1 — Crystal oscillator input |
| Pin produk 12 | OSC2 — Crystal oscillator output |
| Pin produk 13 | MCLR — Master Clear (reset, active low) |
| Pin produk 14 | PGED1 — Programming/Debug data |
| Pin produk 15 | PGEC1 — Programming/Debug clock |
| Pin produk 16 | PGED2 — Secondary programming data |
| Pin produk 17 | PGEC2 — Secondary programming clock |
| Pin produk 18 | RA0 — I/O port A bit 0 |
| Pin produk 19 | RA1 — I/O port A bit 1 |
| Pin produk 20 | RA2 — I/O port A bit 2 |
| Pin produk 21 | RA3 — I/O port A bit 3 |
| Pin produk 22 | RA4 — I/O port A bit 4 |
| Pin produk 23 | RA5 — I/O port A bit 5 |
| Pin produk 24 | RA6 — I/O port A bit 6 |
| Pin produk 25 | RA7 — I/O port A bit 7 |
| Pin produk 26 | RB0 — I/O port B bit 0 |
| Pin produk 27 | RB1 — I/O port B bit 1 |
| Pin produk 28 | RB2 — I/O port B bit 2 |
| Pin produk 29 | RB3 — I/O port B bit 3 |
| Pin produk 30 | RB4 — I/O port B bit 4 |
| Pin produk 31 | RB5 — I/O port B bit 5 |
| Pin produk 32 | RB6 — I/O port B bit 6 |
| Pin produk 33 | RB7 — I/O port B bit 7 |
| Pin produk 34 | RC0 — I/O port C bit 0 |
| Pin produk 35 | RC1 — I/O port C bit 1 |
| Pin produk 36 | RC2 — I/O port C bit 2 |
| Pin produk 37 | RC3 — I/O port C bit 3 |
| Pin produk 38 | RC4 — I/O port C bit 4 |
| Pin produk 39 | RC5 — I/O port C bit 5 |
| Pin produk 40 | RC6 — I/O port C bit 6 |
| Pin produk 41 | RC7 — I/O port C bit 7 |
| Pin produk 42 | RD0 — I/O port D bit 0 |
| Pin produk 43 | RD1 — I/O port D bit 1 |
| Pin produk 44 | RD2 — I/O port D bit 2 |
| Pin produk 45 | RD3 — I/O port D bit 3 |
| Pin produk 46 | RD4 — I/O port D bit 4 |
| Pin produk 47 | RD5 — I/O port D bit 5 |
| Pin produk 48 | RD6 — I/O port D bit 6 |
| Pin produk 49 | RD7 — I/O port D bit 7 |
| Pin produk 50 | RE0 — I/O port E bit 0 |
| Pin produk 51 | RE1 — I/O port E bit 1 |
| Pin produk 52 | RE2 — I/O port E bit 2 |
| Pin produk 53 | RE3 — I/O port E bit 3 |
| Pin produk 54 | RE4 — I/O port E bit 4 |
| Pin produk 55 | RE5 — I/O port E bit 5 |
| Pin produk 56 | RE6 — I/O port E bit 6 |
| Pin produk 57 | RE7 — I/O port E bit 7 |
| Pin produk 58 | RF0 — I/O port F bit 0 |
| Pin produk 59 | RF1 — I/O port F bit 1 |
| Pin produk 60 | RF2 — I/O port F bit 2 |
| Pin produk 61 | RF3 — I/O port F bit 3 |
| Pin produk 62 | RF4 — I/O port F bit 4 |
| Pin produk 63 | RF5 — I/O port F bit 5 |
| Pin produk 64 | RF6 — I/O port F bit 6 |
| Pin produk 65 | RF7 — I/O port F bit 7 |
| Pin produk 66 | RG0 — I/O port G bit 0 |
| Pin produk 67 | RG1 — I/O port G bit 1 |
| Pin produk 68 | RG2 — I/O port G bit 2 |
| Pin produk 69 | RG3 — I/O port G bit 3 |
| Pin produk 70 | AVDD — Analog supply |
| Pin produk 71 | AVSS — Analog ground |
| Pin produk 72 | VDD — Core logic supply |
| Pin produk 73 | VSS — Ground |
| Pin produk 74 | C1RX — CAN1 receive |
| Pin produk 75 | C1TX — CAN1 transmit |
| Pin produk 76 | U1RX — UART1 receive |
| Pin produk 77 | U1TX — UART1 transmit |
| Pin produk 78 | PWM1H — PWM1 high-side output |
| Pin produk 79 | PWM1L — PWM1 low-side output |
| Pin produk 80 | NC — Not connected (per datasheet) |
Aplikasi Umum
DSPIC30F6013T-30I/PF cocok untuk 6 aplikasis: BLDC / PMSM Motor Control, Digital Power Conversion (UPS / Solar Inverter), Automotive Body and Chassis Controllers, Audio Signal Processing, Industrial Sensor Signal Conditioning, Uninterruptible Power Supply (UPS) Controllers.
BLDC / PMSM Motor Control
The DSPIC30F6013T-30I/PF's 30 MIPS DSP engine, motor-control PWM module, and 12-bit ADC make it ideal for brushless DC and permanent-magnet synchronous motor drives. Its single-cycle 16x16 MAC supports field-oriented control (FOC) algorithms with torque ripple below 2%. The 80-pin TQFP exposes sufficient PWM channels and ADC inputs for direct three-phase inverter drive without external logic. Engineers implementing sensorless FOC benefit from the DSP engine's fractional arithmetic for Park/Clarke transforms and PI loop execution under 10 us per control cycle. The 6 KB RAM accommodates state estimators and reference frames. Compared with general-purpose MCUs lacking DSP extensions, the dsPIC30F reduces CPU loading by 40-60% in motor-control firmware.
Direkomendasikan
Digital Power Conversion (UPS / Solar Inverter)
For digital power supplies and solar inverter MPPT algorithms, the DSPIC30F6013T-30I/PF combines DSP throughput with MCU determinism. The 30 MIPS engine executes voltage-mode and current-mode control loops at 50-100 kHz switching frequencies. The 12-bit ADC samples feedback signals at sub-microsecond conversion rates, and the PWM module generates phase-shifted gate-drive waveforms for bridgeless PFC topologies. The 132 KB Flash accommodates state-space control firmware and lookup tables for MPPT and THD optimization. Operating from 2.5V-5.5V, the device interfaces directly to 3.3V gate drivers and 5V analog front-ends. The 6 KB RAM holds ADC sample buffers and PID state variables.
Direkomendasikan
Automotive Body and Chassis Controllers
The DSPIC30F6013T-30I/PF's industrial temperature range (-40C to +85C), CAN peripheral, and DSP capability suit automotive body controllers for window lifts, seat positioners, and HVAC blowers. The 30 MIPS throughput executes multiple LIN/CAN message handlers alongside motor-control routines without CPU starvation. The 80-pin TQFP provides sufficient I/O for sensor interfacing and H-bridge driver control. Automotive applications benefit from the DSP engine for sensor fusion in chassis control units, where accelerometer and gyroscope data are filtered in real time. Although AEC-Q100 qualification is not stated, the device's industrial temperature grade and robust Flash memory support under-hood and body-module deployments.
Direkomendasikan
Audio Signal Processing
The DSPIC30F6013T-30I/PF delivers DSP throughput for low-cost audio effects processors, equalizers, and active noise-cancellation front-ends. Its single-cycle MAC executes biquad filters and FFTs at CD-quality sample rates (44.1 kHz). The 132 KB Flash stores filter coefficients and preset tables, while 6 KB RAM buffers audio frames. The I2S-compatible SPI peripheral interfaces to common audio codecs. Compared with dedicated audio DSPs, the dsPIC30F trades absolute throughput for integrated MCU peripherals and lower BOM cost. Typical use cases include karaoke mixers, hearing-aid pre-processing, and guitar multi-effects pedals.
Direkomendasikan
Industrial Sensor Signal Conditioning
For industrial process control, the DSPIC30F6013T-30I/PF digitizes and filters signals from strain gauges, thermocouples, and pressure sensors. Its 12-bit ADC (up to 16 channels) multiplexes sensor inputs, and the DSP engine implements digital IIR filters with 60 dB stopband attenuation. The 2.5V-5.5V supply range supports 4-20 mA loop-powered transmitters and 24V industrial buses via external regulators. UART/SPI/CAN peripherals connect to PLC backplanes and industrial Ethernet gateways. The 132 KB Flash stores calibration constants and linearization tables for thermocouple cold-junction compensation.
Direkomendasikan
Uninterruptible Power Supply (UPS) Controllers
The DSPIC30F6013T-30I/PF's DSP engine excels in UPS digital control loops, where it computes inverter output voltage regulation, battery charging profiles, and load-sharing algorithms in real time. The motor-control PWM module generates sine-triangle PWM with dead-time insertion for IGBT gate drives. The 80-pin TQFP provides dedicated pins for grid synchronization, battery management, and bypass switching. The 6 KB RAM holds grid-cycle state variables, while 132 KB Flash stores inverter firmware and battery chemistry profiles. Operating from 2.5V-5.5V, the device pairs with external gate drivers and isolated ADC front-ends.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DSPIC30F6013T-30I/PF — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DSPIC30F6014T-30I/PF | DSPIC30F6013AT-30I/PT | DSPIC30F6013A-30I/PF | DSPIC30F6012AT-30I/PF |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 80-pin TQFP (14x14) | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same | 80-pin TQFP (14x14) - same |
| Flash Memory | 132 KB | 132 KB | 132 KB | 132 KB | 144 KB |
| RAM | 6 KB | 6 KB | 6 KB | 6 KB | 8 KB |
| CPU Speed | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz | 30 MIPS at 30 MHz |
| CAN Peripheral | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) | Yes (1x CAN) |
| Lifecycle Status | Obsolete | Obsolete | Active | Active | Active |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 2.5 V to 5.5 V |
| RoHS Compliance | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant |
Diferensiator Kunci
- Single-cycle 16x16 MAC DSP engine (vsDSPIC30F4013-20I/ML)
- 132 KB Flash with 80-pin TQFP package (vsDSPIC30F5011-30I/PT)
- Active lifecycle silicon A revision available (vsDSPIC30F6013T-30I/PF (this part))
Catatan Desain
The 80-pin TQFP package has a typical theta_JA of approximately 45-55 C/W on a standard 4-layer JEDEC test board. At full 30 MIPS operation with all peripherals active, internal dissipation is approximately 0.5-0.8 W. For motor-control applications driving high-current IGBTs via external gate drivers, ensure the PCB provides adequate copper pour (at least 1 sq inch) connected to the thermal pad or VSS pins to keep junction temperature below 125 C. In enclosed industrial enclosures, consider airflow or heat-sinking the inverter heatsink shared with the DSC thermal mass.
Place 100 nF decoupling capacitors as close as possible to each VDD/VSS pair (typically 4-6 pairs on the 80-pin TQFP). Add a 10 uF bulk capacitor near the AVDD pin for ADC reference stability. Keep analog input traces (AN0-AN15) away from PWM switching traces and clock signals to minimize coupling. For motor-control applications, route the three-phase PWM outputs (PWM1H/L through PWM3H/L) symmetrically with equal-length traces to maintain switching timing alignment.
When migrating code from DSPIC30F6013 to DSPIC30F6013A silicon revision, consult the device errata document - the 'A' revision fixes several PWM and ADC peripheral bugs but may introduce silicon ID changes that affect bootloader code. Do not assume Q15 fractional arithmetic without configuring the CORCON register appropriately. When using the CAN peripheral, configure the CAN I/O pins via the PPS (Peripheral Pin Select) module before enabling the CAN module, or the device may enter an undefined state.
The DSPIC30F6013T-30I/PF's 30 MIPS operation generates fast-edge signals on PWM outputs (rise times <10 ns). Use series damping resistors (10-33 ohm) on PWM outputs driving long cables or external gate drivers to limit ringing. For ADC inputs, add RC low-pass filters (1 kohm + 100 pF) to reject switching noise from PWM traces crossing analog signal paths. Verify signal integrity with oscilloscope measurements at full load before finalizing PCB layout.
Informasi Konformitas
ROHS3 Compliant per Microchip USA product page. AEC-Q100 qualification not stated for this part; AEC-Q100 grade variants may exist in the dsPIC33 family for automotive applications. REACH compliance inferred from Microchip's standard compliance statements.
