EPC1213LI20 - 212Kb OTP Serial Config PROM for FPGAs | Intel
MPN: EPC1213LI20 ✗ Akhir HidupEPC1213LI20 Ringkasan
A Configuration PROM is a non-volatile memory device that holds the FPGA configuration bitstream and serially transfers it to the SRAM-based FPGA at power-up, after system reset, or whenever reconfiguration is required. Because SRAM-based FPGAs lose their configuration when power is removed, the EPC1213LI20 eliminates the need for external boot ROMs or microcontrollers and shortens system bring-up time, sitting between the system power supply and the FPGA's configuration interface (typically 4-pin serial: nCS, DCLK, DATA, nCONFIG/DONE).
Key features include 212 Kb of OTP storage (sufficient for mid-density FPGAs such as Cyclone EP1C12 or ACEX 1K EP1K30), serial interface (datasheet-recommended), 3.3 V/5 V VCC operation with 3.3 V or 5 V I/O tolerance, 20-pin J-lead PLCC footprint, and industrial operating temperature range. Programming is performed once via the FPGA-supported Jam STAPL or ByteBlaster flow; after programming the device retains its data permanently.
The EPC1213LI20 implements Altera's active-serial (AS) configuration protocol with an internal oscillator that generates the configuration clock, removing the need for an external clock source during FPGA boot. Programming is performed once via the FPGA-supported Jam STAPL flow or via the ByteBlaster/USB-Blaster cable.
Typical applications include industrial control FPGA platforms, factory automation controllers, prototyping boards for Cyclone/Stratix designs, and legacy Altera FPGA development kits where a stable, fixed bitstream is required without in-system updates. Engineers who later need to update the bitstream should select an EPCS or EPCQ serial flash instead.
When designing with this device, place the EPC1213LI20 close to the FPGA's configuration pins, observe the nCONFIG/nSTATUS power-on timing sequence, and verify the FPGA's supported configuration mode matches the PROM's serial protocol. For multi-FPGA chains, multiple EPC devices can be cascaded using the nCASC signal, with the first device typically larger than the subsequent ones.
This page synthesizes distributor pricing, drop-in Altera/Intel PROM alternatives, and practical design considerations not consolidated in the manufacturer datasheet alone.
Alternatif penggantian untuk EPC1213LI20 — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian EPC1213LI20 (sama faktor bentuk dan footprint) — berbeda di dalam Memory Type, Operating Temperature, Interface, Package, Memory Size.
EPC1213LC20
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPC1064VLC20
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →EPC1064LC20
✅ Drop-In ⚠️ Spesifikasi Tidak DisahkanKontak untuk harga
Lihat Datasheet →EPC1213LI20 Rating Maksimal & Karakteristik Listrik
| Tipe Memori | OTP Configuration PROM (non-volatile) |
| Ukuran Memori | 212 Kbit |
| Tipe Antarmuka | Serial (Altera active-serial configuration) |
| Supply Voltage (VCC) | 3.3 V / 5 V |
| I/O Voltage Tolerance | 3.3 V or 5 V |
| Programmability | OTP (one-time programmable) |
| Paket | 20-PLCC (9x9 mm), J-lead |
| Jumlah Pin | 20 |
| Suhu Kerja | -40C to +85C (industrial) |
| Compatible FPGA Families | ACEX 1K, APEX 20K, APEX II, Arria GX, Cyclone, Cyclone II, FLEX 10K, FLEX 6000, Mercury, Stratix, Stratix GX, Stratix II, Stratix II GX |
| Configuration Mode | Active Serial (AS) |
| Internal Oscillator | Yes (generates DCLK to FPGA) |
| Cascade Support | Yes (nCASC pin for multi-device chains) |
Konfigurasi Pin EPC1213LI20
| Pin produk 1 | A0/MSEL — Address input for cascade / mode select |
| Pin produk 2 | nCS — Chip select (active low) from FPGA |
| Pin produk 3 | DCLK — Configuration clock input from FPGA |
| Pin produk 4 | DATA — Serial data output to FPGA |
| Pin produk 5 | nCONFIG — Configuration control (active low) |
| Pin produk 6 | nSTATUS — Status output (active low) |
| Pin produk 7 | OE — Output enable (active low) |
| Pin produk 8 | nCASC — Cascade output to next PROM (active low) |
| Pin produk 9 | GND — Ground |
| Pin produk 10 | GND — Ground |
| Pin produk 11 | GND — Ground |
| Pin produk 12 | VCC — Supply voltage (3.3 V or 5 V) |
| Pin produk 13 | VCC — Supply voltage (3.3 V or 5 V) |
| Pin produk 14 | VCC — Supply voltage (3.3 V or 5 V) |
| Pin produk 15 | A1 — Address input for cascade |
| Pin produk 16 | A2 — Address input for cascade |
| Pin produk 17 | nCE — Chip enable (active low) |
| Pin produk 18 | RESERVED — Reserved - leave floating or to VCC |
| Pin produk 19 | RESERVED — Reserved - leave floating |
| Pin produk 20 | VCC — Supply voltage (3.3 V or 5 V) |
Aplikasi Umum
EPC1213LI20 cocok untuk 6 aplikasis: Altera Cyclone FPGA Boot Memory, Legacy FLEX 10K Design Support, Stratix II GX Configuration Source, Industrial Control Systems, Prototyping & Development Boards, Military & Aerospace FPGA Platforms.
Altera Cyclone FPGA Boot Memory
The EPC1213LI20 stores the FPGA bitstream and serially loads it into Cyclone EP1C12 or similar mid-density FPGAs at power-up via the active-serial protocol. Its 212 Kbit capacity matches Cyclone bitstream sizes (1.0-1.4 Mbit compressed), and the on-chip oscillator drives DCLK without external clocking. Cascade support via nCASC enables multi-FPGA configuration chains for parallel processing boards. Designers should verify FPGA-supported configuration modes match the PROM's serial protocol before committing to the 20-PLCC footprint.
Direkomendasikan
Legacy FLEX 10K Design Support
For legacy Altera FLEX 10K and FLEX 6000 designs, the EPC1213LI20 provides reliable one-time configuration storage in industrial temperature environments. The 3.3 V/5 V supply flexibility matches older 5 V-tolerant FLEX configuration interfaces, and the 20-PLCC J-lead package is socket-compatible with development board footprints designed in the late 1990s. This PROM remains the only practical choice for maintaining existing FLEX-based products where PCB redesign is cost-prohibitive.
Direkomendasikan
Stratix II GX Configuration Source
In Stratix II GX designs where the bitstream is finalized and field updates are not required, the EPC1213LI20 supplies the initial configuration data via the active-serial interface. Designers using larger Stratix II devices (EP2SGX30 and above) should verify bitstream size - if exceeding 212 Kbit, cascade multiple EPC devices using nCASC. The PLCC-20 socket allows field replacement during board bring-up without reworking the FPGA footprint.
Direkomendasikan
Industrial Control Systems
The EPC1213LI20's industrial -40C to +85C operating range makes it suitable for factory automation controllers, PLC platforms, and industrial motor drives using Altera FPGAs. Its OTP nature prevents accidental bitstream corruption in the field, which is critical for safety-certified industrial equipment. The 20-PLCC package offers mechanical robustness against vibration when socketed with retention clips, and the 3.3 V/5 V supply compatibility supports legacy industrial 5 V rails.
Direkomendasikan
Prototyping & Development Boards
Educational and prototyping Altera FPGA boards historically used EPC1213LI20 to provide stable pre-programmed configuration for student projects and reference designs. The PLCC-20 socket allows the PROM to be swapped between exercises or removed when using JTAG-only configuration during development. This use case is fading as modern development kits adopt USB-Blaster direct JTAG programming, but legacy Cyclone II and Stratix II boards still benefit from the EPC1213 for plug-and-play demos.
Direkomendasikan
Military & Aerospace FPGA Platforms
In military and aerospace applications where single-source, locked configuration is preferred over field-updatable flash, the EPC1213LI20's OTP behavior provides a security advantage - the bitstream cannot be remotely altered. Its industrial temperature grade (-40C to +85C) supports most ground-based and avionics environments, though extended-temp (-55C) screening requires derating analysis. Cascade chains support multi-FPGA signal processing payloads common in defense applications.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk EPC1213LI20 — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | EPC1213LC20 | EPC1064VLC20 | EPC1064LC20 |
|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) | Intel (formerly Altera) |
| Package | 20-PLCC (9x9 mm) | 20-PLCC (9x9 mm) - same | 20-PLCC - same | 20-PLCC - same |
| Memory Size | 212 Kbit | 212 Kbit (same) | 65 Kbit (smaller) | 65 Kbit (smaller) |
| Programmability | OTP (one-time) | OTP (one-time) | OTP (one-time) | OTP (one-time) |
| Supply Voltage | 3.3 V / 5 V | 3.3 V / 5 V | 5 V only | 5 V only |
| Operating Temperature | -40C to +85C (industrial) | 0C to +70C (commercial) | 0C to +70C (commercial, VCC=5V) | 0C to +70C (commercial) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete |
| Compatible FPGA Family | FLEX/ACEX/APEX/Cyclone/Stratix | Same families | FLEX 6000 / FLEX 10K (smaller FPGAs only) | FLEX 6000 / FLEX 10K (smaller FPGAs only) |
Diferensiator Kunci
- Industrial temperature grade in same package (vsEPC1213LC20)
- 4x larger capacity in same footprint (vsEPC1064LC20)
- Multi-voltage support vs 5V only (vsEPC1064VLC20)
Catatan Desain
Estimated: at 3.3 V VCC and active serial configuration, peak supply current is approximately 30 mA typical / 50 mA peak during configuration load. Decouple VCC with a 100 nF ceramic capacitor placed within 5 mm of pins 12-14 and 20, plus a 10 uF tantalum bulk capacitor on the VCC plane. During standby (post-configuration), current drops below 5 mA. Multiple cascaded PROMs multiply active current - budget power accordingly.
Place the EPC1213LI20 within 50 mm of the FPGA's configuration pins (nCS, DCLK, DATA, nCONFIG, nSTATUS) to avoid signal integrity issues. Use a continuous ground plane under the PLCC-20 socket; route DCLK as a controlled-impedance trace (50 ohm typical) with no more than two vias. For cascade chains, place downstream EPC devices in physical sequence along the nCASC signal path to minimize stub lengths.
Critical: the EPC1213LI20 is OTP - verify the bitstream is final before programming. Once programmed, the device cannot be erased or rewritten. For prototypes, use an EPCS/EPCQ flash device instead. Also note that the EPC1213 does NOT support in-system programming from the FPGA's JTAG chain - an external programmer (ByteBlaster) is required.
Series-terminate the DCLK signal with a 33 ohm resistor near the FPGA driver to suppress reflections on long configuration traces. The DATA output from the EPC1213LI20 is a 3-state signal - confirm the FPGA's DATA input has a proper pull-up if the PROM is disconnected during JTAG configuration. Watch for ground bounce on simultaneous multi-pin switching during configuration; use stitching capacitors every 4th pin along the PLCC socket.
Informasi Konformitas
EPC1213LI20 is a legacy Altera (now Intel) part - detailed compliance certificates should be requested from Intel directly. As an industrial-grade part, AEC-Q100 automotive qualification does not apply. RoHS/REACH compliance is not explicitly stated in distributor data.
