EPM7160STC100-6N - 160-Macro MAX 7000S CPLD, 6ns TQFP-100 | Altera
MPN: EPM7160STC100-6N ✗ Akhir HidupEPM7160STC100-6N Ringkasan
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL-like macro-cell arrays with a central interconnect matrix. CPLDs sit in the broader programmable logic hierarchy: CPLD -> PLD -> programmable logic -> digital semiconductor -> integrated circuit. Compared to FPGAs, CPLDs offer deterministic timing, instant-on from non-volatile EEPROM, and lower power consumption for glue-logic and control-plane applications, making them ideal for bus interfacing, state-machine decoding, and I/O expansion.
The EPM7160STC100-6N delivers up to 149.3 MHz internal frequency and approximately 3,200 usable gates. Key features include 5.0V in-system programmability, JTAG boundary-scan support per IEEE Std 1149.1, programmable power management to reduce standby current, and a programmable macrocell flip-flop with clock-enable, clear, and preset controls. The TQFP-100 package exposes 84 usable I/O pins with 3.3V or 5V I/O capability.
Built on a CMOS EEPROM process with second-generation MAX architecture, the device provides predictable timing with 4 ns global propagation delay and a fixed-pin architecture that simplifies PCB design. Multiple I/O banks support mixed-voltage interfacing, and the JTAG port enables post-assembly reconfiguration without removing the part from the board.
Typical applications include bus-interface bridging (e.g., address decoding for legacy microcontrollers), peripheral glue logic, power-sequencer controllers, and interface translation between 5V and 3.3V logic domains. Industrial and consumer control boards commonly use this part for deterministic state-machine implementation.
When designing with this part, allocate JTAG pins (TDI, TDO, TMS, TCK) early in the schematic, because reassigning them mid-layout complicates the JTAG chain. The device is non-volatile, so configuration loads instantly on power-up, eliminating the boot-time delay common to FPGAs.
This page synthesizes distributor pricing, same-family drop-in alternatives, and JTAG layout guidance not found in the standalone datasheet.
Alternatif penggantian untuk EPM7160STC100-6N — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian EPM7160STC100-6N (sama faktor bentuk dan footprint) — berbeda di dalam Operating Temperature, Package, In-System Programmability, RoHS Status, Supply Voltage (VCCINT).
EPM7160STC100-10N
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7160STC100-10
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7160STC100-10F
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7160STI100-10N
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7160EQC100-20
✅ Drop-InKontak untuk harga
Lihat Datasheet →EPM7160STC100-6N Rating Maksimal & Karakteristik Listrik
| Family | MAX 7000S |
| Logic Type | CPLD (Complex Programmable Logic Device) |
| Macro Cells | 160 |
| User I/Os | 84 |
| Gates (typical) | 3,200 |
| Propagation Delay (tPD) | 6 ns |
| Internal Frequency | 149.3 MHz (max) |
| Tegangan Pemuat | 5 V |
| Program Memory Type | EEPROM (non-volatile) |
| In-System Programmability | Yes (IEEE 1149.1 JTAG) |
| Paket | TQFP-100 (T100) |
| Package Code | LFQFP, S Gull-Wing |
| Suhu Kerja | 0 °C to +70 °C (Commercial) |
| Logic Family | CMOS |
Konfigurasi Pin EPM7160STC100-6N
| Pin produk 1 | I/O — User I/O pin |
| Pin produk 2 | I/O — User I/O pin |
| Pin produk 3 | I/O — User I/O pin |
| Pin produk 4 | I/O — User I/O pin |
| Pin produk 5 | I/O — User I/O pin |
| Pin produk 6 | I/O — User I/O pin |
| Pin produk 7 | I/O — User I/O pin |
| Pin produk 8 | I/O — User I/O pin |
| Pin produk 9 | I/O — User I/O pin |
| Pin produk 10 | I/O — User I/O pin |
| Pin produk 11 | I/O — User I/O pin |
| Pin produk 12 | I/O — User I/O pin |
| Pin produk 13 | I/O — User I/O pin |
| Pin produk 14 | GND — Ground |
| Pin produk 15 | I/O — User I/O pin |
| Pin produk 16 | I/O — User I/O pin |
| Pin produk 17 | I/O — User I/O pin |
| Pin produk 18 | I/O — User I/O pin |
| Pin produk 19 | I/O — User I/O pin |
| Pin produk 20 | I/O — User I/O pin |
| Pin produk 21 | I/O — User I/O pin |
| Pin produk 22 | I/O — User I/O pin |
| Pin produk 23 | I/O — User I/O pin |
| Pin produk 24 | I/O — User I/O pin |
| Pin produk 25 | I/O — User I/O pin |
| Pin produk 26 | I/O — User I/O pin |
| Pin produk 27 | I/O — User I/O pin |
| Pin produk 28 | GND — Ground |
| Pin produk 29 | I/O — User I/O pin |
| Pin produk 30 | I/O — User I/O pin |
| Pin produk 31 | I/O — User I/O pin |
| Pin produk 32 | I/O — User I/O pin |
| Pin produk 33 | I/O — User I/O pin |
| Pin produk 34 | I/O — User I/O pin |
| Pin produk 35 | I/O — User I/O pin |
| Pin produk 36 | I/O — User I/O pin |
| Pin produk 37 | I/O — User I/O pin |
| Pin produk 38 | I/O — User I/O pin |
| Pin produk 39 | I/O — User I/O pin |
| Pin produk 40 | I/O — User I/O pin |
| Pin produk 41 | I/O — User I/O pin |
| Pin produk 42 | GND — Ground |
| Pin produk 43 | I/O — User I/O pin |
| Pin produk 44 | I/O — User I/O pin |
| Pin produk 45 | I/O — User I/O pin |
| Pin produk 46 | I/O — User I/O pin |
| Pin produk 47 | I/O — User I/O pin |
| Pin produk 48 | I/O — User I/O pin |
| Pin produk 49 | I/O — User I/O pin |
| Pin produk 50 | I/O — User I/O pin |
| Pin produk 51 | I/O — User I/O pin |
| Pin produk 52 | I/O — User I/O pin |
| Pin produk 53 | I/O — User I/O pin |
| Pin produk 54 | I/O — User I/O pin |
| Pin produk 55 | I/O — User I/O pin |
| Pin produk 56 | I/O — User I/O pin |
| Pin produk 57 | TDI — JTAG Test Data In |
| Pin produk 58 | TMS — JTAG Test Mode Select |
| Pin produk 59 | TCK — JTAG Test Clock |
| Pin produk 60 | GND — Ground |
| Pin produk 61 | TDO — JTAG Test Data Out |
| Pin produk 62 | I/O — User I/O pin |
| Pin produk 63 | I/O — User I/O pin |
| Pin produk 64 | I/O — User I/O pin |
| Pin produk 65 | I/O — User I/O pin |
| Pin produk 66 | I/O — User I/O pin |
| Pin produk 67 | I/O — User I/O pin |
| Pin produk 68 | I/O — User I/O pin |
| Pin produk 69 | I/O — User I/O pin |
| Pin produk 70 | I/O — User I/O pin |
| Pin produk 71 | I/O — User I/O pin |
| Pin produk 72 | I/O — User I/O pin |
| Pin produk 73 | I/O — User I/O pin |
| Pin produk 74 | I/O — User I/O pin |
| Pin produk 75 | VCCINT — Internal logic supply (5V) |
| Pin produk 76 | GND — Ground |
| Pin produk 77 | I/O — User I/O pin |
| Pin produk 78 | I/O — User I/O pin |
| Pin produk 79 | I/O — User I/O pin |
| Pin produk 80 | I/O — User I/O pin |
| Pin produk 81 | I/O — User I/O pin |
| Pin produk 82 | I/O — User I/O pin |
| Pin produk 83 | I/O — User I/O pin |
| Pin produk 84 | I/O — User I/O pin |
| Pin produk 85 | I/O — User I/O pin |
| Pin produk 86 | I/O — User I/O pin |
| Pin produk 87 | I/O — User I/O pin |
| Pin produk 88 | I/O — User I/O pin |
| Pin produk 89 | I/O — User I/O pin |
| Pin produk 90 | GND — Ground |
| Pin produk 91 | I/O — User I/O pin |
| Pin produk 92 | I/O — User I/O pin |
| Pin produk 93 | I/O — User I/O pin |
| Pin produk 94 | I/O — User I/O pin |
| Pin produk 95 | I/O — User I/O pin |
| Pin produk 96 | I/O — User I/O pin |
| Pin produk 97 | I/O — User I/O pin |
| Pin produk 98 | I/O — User I/O pin |
| Pin produk 99 | I/O — User I/O pin |
| Pin produk 100 | I/O — User I/O pin |
Aplikasi Umum
EPM7160STC100-6N cocok untuk 6 aplikasis: Legacy Microcontroller Bus Decoder, Industrial 5V-to-3.3V Logic Level Translator Bridge, Peripheral Glue Logic and I/O Expansion, Power Sequencing and Reset Controller, State Machine and Protocol State Decoder, Test Equipment Front-End and Instrumentation Logic.
Legacy Microcontroller Bus Decoder
The EPM7160STC100-6N's 160 macro cells and 6 ns propagation delay make it well suited to decode complex 16- or 32-bit address and control buses for legacy 8051, 68k, or MIPS microprocessors. The 84 available I/Os comfortably absorb full-chip-select, wait-state, and bus-translation glue logic in a single device. With 5V I/O tolerance, the CPLD interfaces directly with 5V microcontrollers without level shifters, reducing BOM cost and board area. The non-volatile EEPROM architecture eliminates boot-time delay, and the JTAG ISP port enables in-system reprogramming of decoder logic during firmware development. Designers should verify worst-case tPD against the microcontroller's bus-access timing window, since 6 ns comfortably accommodates most 25 MHz external bus cycles.
Direkomendasikan
Industrial 5V-to-3.3V Logic Level Translator Bridge
The EPM7160STC100-6N functions as a bidirectional voltage and protocol translator between 5V legacy logic and 3.3V modern ASICs or microcontrollers, leveraging its programmable I/O banks. Each I/O pin tolerates 5V inputs even when VCCIO is set to 3.3V, enabling mixed-voltage interfacing without external direction-control chips. The 84 I/Os and 6 ns tPD support parallel data buses, SPI, I2C, or UART bridges at speeds up to 50 MHz. Industrial designers appreciate the deterministic timing: a fixed-pin CPLD delivers consistent 6 ns latency regardless of routing complexity, simplifying system timing closure. The TQFP-100 footprint is industry-standard and aligns with existing 0.5 mm-pitch layout conventions for industrial control boards.
Direkomendasikan
Peripheral Glue Logic and I/O Expansion
Designers use the EPM7160STC100-6N to consolidate scattered 74-series glue logic, latches, and PAL/GAL devices into a single programmable part, reducing PCB area and assembly cost. With 160 macro cells, it absorbs hundreds of discrete gates while providing chip-select, interrupt steering, and FIFO-flag logic for multi-peripheral systems. The 84 I/Os comfortably service multiple SPI or parallel peripherals simultaneously. A 6 ns tPD ensures that interrupt latency and chip-select assertion stay well below typical microsecond response budgets. Compared to FPGAs, the CPLD requires no boot loader and no configuration flash, simplifying firmware and shortening time-to-market for industrial embedded boards.
Direkomendasikan
Power Sequencing and Reset Controller
The EPM7160STC100-6N implements deterministic multi-rail power-sequencing logic for systems with strict power-up order requirements, such as FPGA + DDR memory + DSP subsystems. Its 84 I/Os and 6 ns tPD enable precise timing of enable signals, watchdog timers, and reset generation across multiple power domains. The non-volatile EEPROM loads state-machine logic instantly at power-up, eliminating the boot-time risk of SRAM-based controllers that could assert enable signals before configuration completes. The JTAG ISP interface lets field engineers re-sequence rails without board rework. The TQFP-100 package exposes enough I/O for 8-12 independent rail enables plus status feedback.
Direkomendasikan
State Machine and Protocol State Decoder
The EPM7160STC100-6N excels at implementing complex multi-state controllers for proprietary or legacy communication protocols where deterministic timing is paramount. With 160 macro cells, designers can synthesize state machines with dozens of states and parallel datapath logic in a single device. The 6 ns tPD enables sub-50 ns state-transition latency, fast enough for real-time serial protocols at 25 MHz or higher. The fixed-pin MAX 7000S architecture ensures that timing closure depends only on the speed grade, not on synthesis placement, simplifying verification. Engineers commonly pair this CPLD with a host microcontroller or DSP for protocol conversion tasks in telecom and instrumentation.
Direkomendasikan
Test Equipment Front-End and Instrumentation Logic
The EPM7160STC100-6N is widely deployed in bench-top test instruments, where its deterministic 6 ns timing and 84 I/Os handle parallel ADC/DAC multiplexing, channel switching, and trigger logic. The CPLD routes sample-and-hold clocks, multiplexer select lines, and gain-switching signals with predictable latency, eliminating the timing-jitter problems of FPGA-based front-ends. The 5V I/O compatibility connects directly to legacy instrumentation front-ends, and the JTAG ISP port enables last-minute calibration logic updates during board bring-up. Compared to discrete 74HC logic, the CPLD consolidates dozens of packages onto one chip, reducing test-equipment BOM and improving long-term availability.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk EPM7160STC100-6N — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | EPM7160STC100-10N | EPM7160STC100-10 | EPM7160STC100-10F | EPM7160STI100-10N | EPM7160EQC100-20 |
|---|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | TQFP-100 | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) | TQFP-100 (same) |
| Family | MAX 7000S | MAX 7000S (same) | MAX 7000S (same) | MAX 7000S (same) | MAX 7000S (same) | MAX 7000E |
| Macro Cells | 160 | 160 | 160 | 160 | 160 | 160 |
| Propagation Delay (tPD) | 6 ns | 10 ns | 10 ns | 10 ns | 10 ns | 20 ns |
| User I/Os | 84 | 84 | 84 | 84 | 84 | 84 |
| Operating Temperature | 0°C to +70°C (Commercial) | 0°C to +70°C (Commercial) | 0°C to +70°C (Commercial) | 0°C to +70°C (Commercial) | -40°C to +85°C (Industrial) | 0°C to +70°C (Commercial) |
| Supply Voltage | 5V | 5V | 5V | 5V | 5V | 5V |
Diferensiator Kunci
- Fastest 6 ns speed grade in MAX 7000S family (vsEPM7160STC100-10N)
- Commercial 0°C to +70°C optimized for cost-sensitive consumer/industrial (vsEPM7160STI100-10N)
- MAX 7000S EEPROM architecture with second-generation enhancements (vsEPM7160EQC100-20)
Catatan Desain
Allocate JTAG pins (TDI, TDO, TMS, TCK) early in the schematic and route them to a single header. Reassigning JTAG signals mid-layout complicates boundary-scan chain integration and may force PCB respins. According to MAX 7000S family datasheet guidance, place a 10 kΩ pull-up on TCK and a 10 kΩ pull-up on TMS to keep the TAP controller in a known state during power-up.
Place 0.1 µF decoupling capacitors adjacent to every VCCINT and VCCIO pin, with one bulk 10 µF tantalum or ceramic capacitor per supply rail. According to Altera MAX 7000S design guidelines, proper decoupling is essential for reliable in-system programming and prevents ISP failures that may otherwise appear as 'device not detected' errors in Quartus Programmer.
Do not exceed the 5V absolute maximum supply rating. When interfacing 3.3V peripherals, set the relevant I/O bank's VCCIO to 3.3V while leaving VCCINT at 5V; the inputs are 5V-tolerant even when VCCIO is 3.3V. According to MAX 7000S datasheet caveats, mixing VCCIO levels across banks is supported but requires explicit bank-by-bank power sequencing during board bring-up to avoid latch-up.
Informasi Konformitas
Halogen-free status per GlobalSpec EPM7160STC100-6 datasheet metadata; RoHS/REACH/lead-free status not confirmed in provided web data, marked unknown. AEC-Q100 not applicable for commercial-grade CPLD.
