FT232HL - Hi-Speed USB to UART/FIFO Bridge, LQFP-48 | FTDI
MPN: FT232HL ✓ AktifFT232HL Ringkasan
A USB-to-UART/FIFO bridge (or USB bridge IC) is a mixed-signal interface device that translates USB packet transactions on the host side into a parallel or serial peripheral stream on the device side. In the system hierarchy it sits between the USB host controller (an upstream function) and an embedded MCU, FPGA, or sensor (a downstream function). Bridges like the FT232HL eliminate the need for an on-board MCU to handle USB protocol, offloading PHY, framing, and enumeration onto a certified, driver-supported chip. Within the broader taxonomy the FT232HL is: USB bridge -> serial interface IC -> interface IC -> integrated circuit.
Key features include USB 2.0 Hi-Speed compliance (480 Mb/s), support for UART (up to 12 Mbaud), FIFO, FT1248, SPI host (up to 30 MHz via MPSSE) and I2C (up to 3.4 MHz) operating modes, an integrated 1.8V LDO, 3.3V I/O tolerance, and embedded 1024-byte EEPROM for VID/PID customization. The MPSSE (Multi-Protocol Synchronous Serial Engine) block lets the host drive SPI, I2C, and JTAG bit-bang streams directly from the USB endpoint, which is the FT232HL's signature use case.
Internally the FT232HL uses a 60 MHz internal reference and a hardened USB 2.0 PHY. The same die is offered in QFN-32 (FT232HQ), LQFP-48 (FT232HL), and LQFP-48 (FT232HL-TRAY/REEL). All variants share the same MPSSE performance and feature set; only the pinout, thermal pad, and pin count differ. The -L suffix on FT232H denotes the lead-free LQFP-48 package option.
Typical applications include USB-to-UART debug consoles, USB-to-SPI programmers for SPI flash and EEPROM, USB-to-I2C bridge boards, JTAG programming cables, and FPGA configuration loaders. Hobbyist and engineer-friendly boards like the Adafruit FT232H breakout and FTDI C232HM cable are built around this die. The wide driver support across Windows, macOS, and Linux (libFTDI, D2XX, VCP) reduces host-side integration effort.
A key design consideration is the 480 Mb/s USB 2.0 Hi-Speed signaling: route the D+/D- pair as a 90-ohm differential, keep them length-matched, and place the 27-ohm series termination close to the FT232HL pins. Provide a solid ground pour under the LQFP thermal pad and tie VBUS through a 10uF bulk plus 100nF decoupling cap. Reset state on power-up is selected by the default EEPROM image; verify VID/PID values before software bring-up.
Alternatif penggantian untuk FT232HL — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
Variasi di dalam seri ini
Model-series yang sama yang kompatibel dengan penggantian FT232HL (sama faktor bentuk dan footprint) — berbeda di dalam Package, Mounting Type, RoHS Status, UART Data Rate, Function.
FT232HL-REEL
✅ Drop-InKontak untuk harga
Lihat Datasheet →FT232HL-TRAY
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
FT232HQ
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
FT2232HL
✅ Drop-In ⚠️ Spesifikasi Tidak Disahkan📋 Alternatif referensi (tidak dalam katalog)
CY7C65213-28SXIT
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
FT232HL Spesifikasi
| Fungsi | USB 2.0 Hi-Speed to UART/FIFO/SPI/I2C bridge |
| USB Speed | Hi-Speed USB 2.0, 480 Mb/s |
| USB Compliance | USB 2.0 Hi-Speed |
| Serial Modes | UART, FIFO, FT1248, SPI host, I2C host (via MPSSE) |
| UART Data Rate | Up to 12 Mbaud |
| MPSSE Clock | Up to 30 MHz (SPI) |
| I2C Clock (MPSSE) | Up to 3.4 MHz |
| Number of Channels | 1 |
| Supply Voltage (VCC) | 3.0 V to 5.25 V (from VBUS or external 5V) |
| I/O Logic Level | 3.3 V (5 V tolerant inputs on most pins) |
| Internal LDO | 1.8 V core LDO integrated |
| EEPROM | Internal 1024-byte user-configurable |
| Paket | 48-LQFP (7x7 mm, lead-free) |
| Suhu Kerja | -40 C to +85 C |
| Status RoHS | Compliant (lead-free) |
| Tipe Mounting | Surface Mount (LQFP) |
Konfigurasi Pin FT232HL
| Pin produk 1 | VBUS — USB VBUS sense input (5 V from host) |
| Pin produk 2 | VCC — 3.3 V LDO output / external 3.3 V supply |
| Pin produk 3 | VCCIO — I/O supply reference |
| Pin produk 4 | VPLL — 1.8 V PLL supply (filter cap) |
| Pin produk 5 | AGND — Analog ground |
| Pin produk 6 | XI — 12 MHz crystal input |
| Pin produk 7 | XO — 12 MHz crystal output |
| Pin produk 8 | RESET# — Active-low reset (tie to VCCIO via 10K) |
| Pin produk 9 | EECLK — EEPROM clock |
| Pin produk 10 | EEDATA — EEPROM data |
| Pin produk 11 | EECS — EEPROM chip select |
| Pin produk 12 | GND — Ground |
| Pin produk 13 | NC — Not connected (per datasheet) |
| Pin produk 14 | TEST — Test pin (tie to GND) |
| Pin produk 15 | OSCI — Oscillator input (NC for crystal) |
| Pin produk 16 | OSCO — Oscillator output (NC for crystal) |
| Pin produk 17 | D+ — USB D+ data line |
| Pin produk 18 | D- — USB D- data line |
| Pin produk 19 | VCC — USB PHY 3.3 V supply |
| Pin produk 20 | GND — Ground |
| Pin produk 21 | REFIN — Reference input |
| Pin produk 22 | REFOUT — Reference output (1.8 V) |
| Pin produk 23 | AD0 — MPSSE SCK / GPIO0 |
| Pin produk 24 | AD1 — MPSSE MOSI / GPIO1 |
| Pin produk 25 | AD2 — MPSSE MISO / GPIO2 |
| Pin produk 26 | AD3 — MPSSE CS / GPIO3 |
| Pin produk 27 | AD4 — MPSSE GPIO4 |
| Pin produk 28 | AD5 — MPSSE GPIO5 |
| Pin produk 29 | AD6 — MPSSE GPIO6 |
| Pin produk 30 | AD7 — MPSSE GPIO7 |
| Pin produk 31 | GND — Ground |
| Pin produk 32 | AC0 — MPSSE AC0 / I2C SCL |
| Pin produk 33 | AC1 — MPSSE AC1 / I2C SDA |
| Pin produk 34 | AC2 — MPSSE AC2 |
| Pin produk 35 | AC3 — MPSSE AC3 |
| Pin produk 36 | AC4 — MPSSE AC4 |
| Pin produk 37 | AC5 — MPSSE AC5 |
| Pin produk 38 | AC6 — MPSSE AC6 |
| Pin produk 39 | AC7 — MPSSE AC7 |
| Pin produk 40 | VCCIO — I/O supply reference |
| Pin produk 41 | GND — Ground |
| Pin produk 42 | PWREN# — Power enable (active low, signals VBUS present) |
| Pin produk 43 | SUSPEND — USB suspend state output |
| Pin produk 44 | TXD — UART transmit (async mode) |
| Pin produk 45 | RXD — UART receive (async mode) |
| Pin produk 46 | RTS# — UART request-to-send (async mode) |
| Pin produk 47 | CTS# — UART clear-to-send (async mode) |
| Pin produk 48 | VCC — USB PHY 3.3 V supply |
Aplikasi Umum
FT232HL cocok untuk 7 aplikasis: USB-to-UART Debug Bridge, USB-to-SPI Flash Programmer, USB-to-I2C Bridge Board, JTAG Programming Cable, FPGA Configuration Loader, USB Bit-Bang GPIO Expander, Industrial USB-Serial Isolated Module.
USB-to-UART Debug Bridge
The FT232HL's UART mode supports data rates up to 12 Mbaud with 3.3 V logic, making it an ideal USB-to-UART debug bridge for embedded MCUs and FPGAs. With USB 2.0 Hi-Speed (480 Mb/s) on the host side, it removes the bottleneck of Full-Speed UART bridges, while on the device side it exposes a true RS-232-style async stream with full hardware flow control. Connect VBUS at 5 V, route D+/D- as a 90-ohm differential, and bridge to a 4-wire UART header; the host sees a COM port via the FTDI VCP driver or a D2XX endpoint. This topology avoids needing an on-board MCU to handle USB protocol.
Direkomendasikan
USB-to-SPI Flash Programmer
The FT232HL's MPSSE engine can drive SPI master mode at up to 30 MHz, which is more than sufficient for programming standard SPI flash (typically 50-104 MHz parts are clocked at 1/2 their max for programming). Use it in production test fixtures or field programmers where you want a pure USB-driven SPI master without an intermediate Cortex-M0. Typical circuit: FT232HL AD0=SCK, AD1=MOSI, AD2=MISO, AD3=CS, plus a 100K pull-up on CS. Throughput is limited by USB bulk endpoint framing (~1 MB/s effective), well within typical SPI flash write speeds.
Direkomendasikan
USB-to-I2C Bridge Board
The FT232HL MPSSE block supports I2C master at up to 3.4 MHz (Fast-mode Plus compatible), enabling USB-to-I2C bridges for sensor hubs and EEPROM programmers. Use 2.2K external pull-ups on SDA/SCL, drive from AD0 (SCL) and AD1 (SDA), and use the libFTDI or D2XX MPSSE APIs on Windows/Linux/macOS. This removes the need for a dedicated USB-to-I2C bridge IC and reuses a single driver across UART/SPI/I2C designs.
Direkomendasikan
JTAG Programming Cable
By driving the FT232HL MPSSE pins as TCK/TMS/TDI/TDO, the chip forms a low-cost USB-to-JTAG cable for CPLD/FPGA configuration and boundary-scan. The MPSSE clock (up to 30 MHz) comfortably exceeds JTAG TCK requirements of most modern FPGAs, while the FT232HL's 48-LQFP footprint fits in a thumb-drive-sized enclosure. OpenOCD and urjtag already support FT232HL-based JTAG cables, eliminating custom firmware.
Direkomendasikan
FPGA Configuration Loader
The FT232HL's FIFO mode streams 8-bit parallel data into an FPGA's configuration port at sustained rates limited by the USB bulk pipeline (typically 1-2 MB/s). This is enough to load most small-to-medium FPGAs (e.g., Cyclone IV, Spartan-6) in under a second, making the FT232HL a strong low-cost choice for factory programming or field firmware updates. Connect AD0-AD7 to D0-D7 of the FPGA config port and use FTDI's D2XX drivers or libFTDI for streaming.
Direkomendasikan
USB Bit-Bang GPIO Expander
When MPSSE is not in use, the FT232HL exposes up to 8 GPIO lines (AD0-AD7) plus 4 EEPROM-controlled GPIO lines, all driven directly from a USB endpoint via D2XX Bit-Bang mode. Engineers use this as a low-cost, OS-agnostic USB-GPIO for lab automation, LED driving, relay control, or production-line fixtures. Bit-bang mode toggles at up to 1 MHz per pin on the FT232HL's Hi-Speed pipe, well above the 1 kHz typical GPIO-update needs.
Direkomendasikan
Industrial USB-Serial Isolated Module
Pair the FT232HL with a digital isolator (e.g., ADuM1411) and a bus-powered isolated DC-DC to build an industrial USB-to-RS-485/422 module. The FT232HL's 3.3 V I/O swings cleanly across the isolator barrier, and its robust driver support across Windows/Linux/macOS avoids custom host software. Add a MAX485 or ISL3179 on the isolated side to complete the link. This is a common industrial pattern where the FT232HL functions as the USB-side protocol engine.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk FT232HL — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | FT232HL-REEL | FT232HL-TRAY | FT232HQ | FT2232HL | CY7C65213-28SXIT |
|---|---|---|---|---|---|---|
| Brand | FTDI | FTDI | FTDI | FTDI | FTDI | Infineon |
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same |
| USB Speed | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Full-Speed USB (12 Mb/s) |
| Channels | 1 | 1 | 1 | 1 | 2 (dual) | 1 |
| MPSSE Engine | Yes (SPI/I2C/JTAG) | Yes | Yes | Yes | Yes (2x MPSSE) | No |
| UART Max Baud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 1 Mbaud |
| FIFO Mode | Yes (8-bit parallel) | Yes | Yes | Yes | Yes | No |
| Internal EEPROM | 1024 bytes | 1024 bytes | 1024 bytes | 1024 bytes | 1024 bytes | Configurable via pins |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| RoHS / Lead-Free | Yes (LQFP, lead-free) | Yes | Yes | Yes | Yes | Yes |
Diferensiator Kunci
- Single-channel Hi-Speed USB 2.0 with MPSSE (vsCY7C65213)
- Versatile multi-protocol serial engine (vsFT232RL)
- 48-LQFP footprint optimized for hand-rework (vsFT232HQ (QFN-32))
Catatan Desain
Route the USB D+ and D- pair as a 90-ohm differential (USB 2.0 Hi-Speed characteristic impedance) with length matching to within 150 mil. Place the 27-ohm series termination resistors (or ferrite beads for EMI) within 5 mm of the FT232HL D+/D- pins. Keep the differential pair on the top layer with a continuous ground pour underneath; do not route over plane splits. Source: FTDI FT232H datasheet layout guidelines.
Decouple VCC (pin 2) and VCCIO (pins 3, 40) with 100 nF X7R ceramic capacitors placed within 2 mm of each pin, plus a single 10 uF bulk capacitor near the VBUS pin. The VPLL pin (4) requires its own 100 nF + 4.7 uF filter network (per FTDI reference design). Estimated: total bulk decoupling budget for a clean USB-2.0 enumeration is approximately 25 uF distributed across VCC, VCCIO, and VPLL.
Do not omit the external 12 MHz crystal on XI/XO (pins 6/7); the FT232HL cannot operate without a stable reference for its internal 480 MHz PLL. Use a crystal with 18-22 pF load capacitance and place within 5 mm of the IC. Common pitfall: leaving EECS (pin 11) floating when no EEPROM is used - this should be tied to GND so the FT232HL falls back to its internal default VID/PID rather than enumerating as an unknown device.
When driving an external target through MPSSE, place a 22-ohm series resistor on each AD0-AD7 and AC0-AC7 line if the cable to the target exceeds 50 mm. This damps ringing on the SPI/I2C edges and prevents double-clocking on long cables. Estimated: the MPSSE clock runs at up to 30 MHz, so a 50 mm unterminated trace presents roughly 5 nH of inductance which can cause >1 V overshoot on a 3.3 V edge.
Informasi Konformitas
Lead-free 48-LQFP package per FTDI product page. RoHS compliant. Not AEC-Q100 qualified; the FT232HL is intended for commercial/industrial USB bridge applications, not automotive.
