FT232HL - Hi-Speed USB to UART/FIFO Bridge, LQFP-48 | FTDI
MPN: FT232HL ✓ فعالFT232HL نمای کلی
A USB-to-UART/FIFO bridge (or USB bridge IC) is a mixed-signal interface device that translates USB packet transactions on the host side into a parallel or serial peripheral stream on the device side. In the system hierarchy it sits between the USB host controller (an upstream function) and an embedded MCU, FPGA, or sensor (a downstream function). Bridges like the FT232HL eliminate the need for an on-board MCU to handle USB protocol, offloading PHY, framing, and enumeration onto a certified, driver-supported chip. Within the broader taxonomy the FT232HL is: USB bridge -> serial interface IC -> interface IC -> integrated circuit.
Key features include USB 2.0 Hi-Speed compliance (480 Mb/s), support for UART (up to 12 Mbaud), FIFO, FT1248, SPI host (up to 30 MHz via MPSSE) and I2C (up to 3.4 MHz) operating modes, an integrated 1.8V LDO, 3.3V I/O tolerance, and embedded 1024-byte EEPROM for VID/PID customization. The MPSSE (Multi-Protocol Synchronous Serial Engine) block lets the host drive SPI, I2C, and JTAG bit-bang streams directly from the USB endpoint, which is the FT232HL's signature use case.
Internally the FT232HL uses a 60 MHz internal reference and a hardened USB 2.0 PHY. The same die is offered in QFN-32 (FT232HQ), LQFP-48 (FT232HL), and LQFP-48 (FT232HL-TRAY/REEL). All variants share the same MPSSE performance and feature set; only the pinout, thermal pad, and pin count differ. The -L suffix on FT232H denotes the lead-free LQFP-48 package option.
Typical applications include USB-to-UART debug consoles, USB-to-SPI programmers for SPI flash and EEPROM, USB-to-I2C bridge boards, JTAG programming cables, and FPGA configuration loaders. Hobbyist and engineer-friendly boards like the Adafruit FT232H breakout and FTDI C232HM cable are built around this die. The wide driver support across Windows, macOS, and Linux (libFTDI, D2XX, VCP) reduces host-side integration effort.
A key design consideration is the 480 Mb/s USB 2.0 Hi-Speed signaling: route the D+/D- pair as a 90-ohm differential, keep them length-matched, and place the 27-ohm series termination close to the FT232HL pins. Provide a solid ground pour under the LQFP thermal pad and tie VBUS through a 10uF bulk plus 100nF decoupling cap. Reset state on power-up is selected by the default EEPROM image; verify VID/PID values before software bring-up.
جایگزین‌های drop-in برای FT232HL — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونه‌ها در این سری
مدل‌های هم‌سری که جایگزین مستقیم هستند برای FT232HL (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Mounting Type, RoHS Status, UART Data Rate, Function.
FT232HL-REEL
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←FT232HL-TRAY
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
FT232HQ
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
FT2232HL
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
CY7C65213-28SXIT
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
FT232HL مشخصات
| عملکرد | USB 2.0 Hi-Speed to UART/FIFO/SPI/I2C bridge |
| USB Speed | Hi-Speed USB 2.0, 480 Mb/s |
| USB Compliance | USB 2.0 Hi-Speed |
| Serial Modes | UART, FIFO, FT1248, SPI host, I2C host (via MPSSE) |
| UART Data Rate | Up to 12 Mbaud |
| MPSSE Clock | Up to 30 MHz (SPI) |
| I2C Clock (MPSSE) | Up to 3.4 MHz |
| Number of Channels | 1 |
| Supply Voltage (VCC) | 3.0 V to 5.25 V (from VBUS or external 5V) |
| I/O Logic Level | 3.3 V (5 V tolerant inputs on most pins) |
| Internal LDO | 1.8 V core LDO integrated |
| EEPROM | Internal 1024-byte user-configurable |
| بسته‌بندی | 48-LQFP (7x7 mm, lead-free) |
| دمای کاری | -40 C to +85 C |
| وضعیت RoHS | Compliant (lead-free) |
| نوع نصب | Surface Mount (LQFP) |
پیکربندی پین FT232HL
| پین 1 | VBUS — USB VBUS sense input (5 V from host) |
| پین 2 | VCC — 3.3 V LDO output / external 3.3 V supply |
| پین 3 | VCCIO — I/O supply reference |
| پین 4 | VPLL — 1.8 V PLL supply (filter cap) |
| پین 5 | AGND — Analog ground |
| پین 6 | XI — 12 MHz crystal input |
| پین 7 | XO — 12 MHz crystal output |
| پین 8 | RESET# — Active-low reset (tie to VCCIO via 10K) |
| پین 9 | EECLK — EEPROM clock |
| پین 10 | EEDATA — EEPROM data |
| پین 11 | EECS — EEPROM chip select |
| پین 12 | GND — Ground |
| پین 13 | NC — Not connected (per datasheet) |
| پین 14 | TEST — Test pin (tie to GND) |
| پین 15 | OSCI — Oscillator input (NC for crystal) |
| پین 16 | OSCO — Oscillator output (NC for crystal) |
| پین 17 | D+ — USB D+ data line |
| پین 18 | D- — USB D- data line |
| پین 19 | VCC — USB PHY 3.3 V supply |
| پین 20 | GND — Ground |
| پین 21 | REFIN — Reference input |
| پین 22 | REFOUT — Reference output (1.8 V) |
| پین 23 | AD0 — MPSSE SCK / GPIO0 |
| پین 24 | AD1 — MPSSE MOSI / GPIO1 |
| پین 25 | AD2 — MPSSE MISO / GPIO2 |
| پین 26 | AD3 — MPSSE CS / GPIO3 |
| پین 27 | AD4 — MPSSE GPIO4 |
| پین 28 | AD5 — MPSSE GPIO5 |
| پین 29 | AD6 — MPSSE GPIO6 |
| پین 30 | AD7 — MPSSE GPIO7 |
| پین 31 | GND — Ground |
| پین 32 | AC0 — MPSSE AC0 / I2C SCL |
| پین 33 | AC1 — MPSSE AC1 / I2C SDA |
| پین 34 | AC2 — MPSSE AC2 |
| پین 35 | AC3 — MPSSE AC3 |
| پین 36 | AC4 — MPSSE AC4 |
| پین 37 | AC5 — MPSSE AC5 |
| پین 38 | AC6 — MPSSE AC6 |
| پین 39 | AC7 — MPSSE AC7 |
| پین 40 | VCCIO — I/O supply reference |
| پین 41 | GND — Ground |
| پین 42 | PWREN# — Power enable (active low, signals VBUS present) |
| پین 43 | SUSPEND — USB suspend state output |
| پین 44 | TXD — UART transmit (async mode) |
| پین 45 | RXD — UART receive (async mode) |
| پین 46 | RTS# — UART request-to-send (async mode) |
| پین 47 | CTS# — UART clear-to-send (async mode) |
| پین 48 | VCC — USB PHY 3.3 V supply |
کاربردهای معمول
FT232HL مناسب است برای 7 کاربردs: USB-to-UART Debug Bridge, USB-to-SPI Flash Programmer, USB-to-I2C Bridge Board, JTAG Programming Cable, FPGA Configuration Loader, USB Bit-Bang GPIO Expander, Industrial USB-Serial Isolated Module.
USB-to-UART Debug Bridge
The FT232HL's UART mode supports data rates up to 12 Mbaud with 3.3 V logic, making it an ideal USB-to-UART debug bridge for embedded MCUs and FPGAs. With USB 2.0 Hi-Speed (480 Mb/s) on the host side, it removes the bottleneck of Full-Speed UART bridges, while on the device side it exposes a true RS-232-style async stream with full hardware flow control. Connect VBUS at 5 V, route D+/D- as a 90-ohm differential, and bridge to a 4-wire UART header; the host sees a COM port via the FTDI VCP driver or a D2XX endpoint. This topology avoids needing an on-board MCU to handle USB protocol.
پیشنهادی
USB-to-SPI Flash Programmer
The FT232HL's MPSSE engine can drive SPI master mode at up to 30 MHz, which is more than sufficient for programming standard SPI flash (typically 50-104 MHz parts are clocked at 1/2 their max for programming). Use it in production test fixtures or field programmers where you want a pure USB-driven SPI master without an intermediate Cortex-M0. Typical circuit: FT232HL AD0=SCK, AD1=MOSI, AD2=MISO, AD3=CS, plus a 100K pull-up on CS. Throughput is limited by USB bulk endpoint framing (~1 MB/s effective), well within typical SPI flash write speeds.
پیشنهادی
USB-to-I2C Bridge Board
The FT232HL MPSSE block supports I2C master at up to 3.4 MHz (Fast-mode Plus compatible), enabling USB-to-I2C bridges for sensor hubs and EEPROM programmers. Use 2.2K external pull-ups on SDA/SCL, drive from AD0 (SCL) and AD1 (SDA), and use the libFTDI or D2XX MPSSE APIs on Windows/Linux/macOS. This removes the need for a dedicated USB-to-I2C bridge IC and reuses a single driver across UART/SPI/I2C designs.
پیشنهادی
JTAG Programming Cable
By driving the FT232HL MPSSE pins as TCK/TMS/TDI/TDO, the chip forms a low-cost USB-to-JTAG cable for CPLD/FPGA configuration and boundary-scan. The MPSSE clock (up to 30 MHz) comfortably exceeds JTAG TCK requirements of most modern FPGAs, while the FT232HL's 48-LQFP footprint fits in a thumb-drive-sized enclosure. OpenOCD and urjtag already support FT232HL-based JTAG cables, eliminating custom firmware.
پیشنهادی
FPGA Configuration Loader
The FT232HL's FIFO mode streams 8-bit parallel data into an FPGA's configuration port at sustained rates limited by the USB bulk pipeline (typically 1-2 MB/s). This is enough to load most small-to-medium FPGAs (e.g., Cyclone IV, Spartan-6) in under a second, making the FT232HL a strong low-cost choice for factory programming or field firmware updates. Connect AD0-AD7 to D0-D7 of the FPGA config port and use FTDI's D2XX drivers or libFTDI for streaming.
پیشنهادی
USB Bit-Bang GPIO Expander
When MPSSE is not in use, the FT232HL exposes up to 8 GPIO lines (AD0-AD7) plus 4 EEPROM-controlled GPIO lines, all driven directly from a USB endpoint via D2XX Bit-Bang mode. Engineers use this as a low-cost, OS-agnostic USB-GPIO for lab automation, LED driving, relay control, or production-line fixtures. Bit-bang mode toggles at up to 1 MHz per pin on the FT232HL's Hi-Speed pipe, well above the 1 kHz typical GPIO-update needs.
پیشنهادی
Industrial USB-Serial Isolated Module
Pair the FT232HL with a digital isolator (e.g., ADuM1411) and a bus-powered isolated DC-DC to build an industrial USB-to-RS-485/422 module. The FT232HL's 3.3 V I/O swings cleanly across the isolator barrier, and its robust driver support across Windows/Linux/macOS avoids custom host software. Add a MAX485 or ISL3179 on the isolated side to complete the link. This is a common industrial pattern where the FT232HL functions as the USB-side protocol engine.
پیشنهادی
خلاصه محصولات پیشنهادی
داده‌های مرجع مهندسی برای FT232HL — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزین‌ها
| پارامتر | این محصول | FT232HL-REEL | FT232HL-TRAY | FT232HQ | FT2232HL | CY7C65213-28SXIT |
|---|---|---|---|---|---|---|
| Brand | FTDI | FTDI | FTDI | FTDI | FTDI | Infineon |
| Package | 48-LQFP (7x7 mm) | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same | 48-LQFP (7x7 mm) - same |
| USB Speed | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Hi-Speed USB 2.0 (480 Mb/s) | Full-Speed USB (12 Mb/s) |
| Channels | 1 | 1 | 1 | 1 | 2 (dual) | 1 |
| MPSSE Engine | Yes (SPI/I2C/JTAG) | Yes | Yes | Yes | Yes (2x MPSSE) | No |
| UART Max Baud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 12 Mbaud | 1 Mbaud |
| FIFO Mode | Yes (8-bit parallel) | Yes | Yes | Yes | Yes | No |
| Internal EEPROM | 1024 bytes | 1024 bytes | 1024 bytes | 1024 bytes | 1024 bytes | Configurable via pins |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
| RoHS / Lead-Free | Yes (LQFP, lead-free) | Yes | Yes | Yes | Yes | Yes |
تفاوت‌های کلیدی
- Single-channel Hi-Speed USB 2.0 with MPSSE (در مقابلCY7C65213)
- Versatile multi-protocol serial engine (در مقابلFT232RL)
- 48-LQFP footprint optimized for hand-rework (در مقابلFT232HQ (QFN-32))
یادداشت‌های طراحی
Route the USB D+ and D- pair as a 90-ohm differential (USB 2.0 Hi-Speed characteristic impedance) with length matching to within 150 mil. Place the 27-ohm series termination resistors (or ferrite beads for EMI) within 5 mm of the FT232HL D+/D- pins. Keep the differential pair on the top layer with a continuous ground pour underneath; do not route over plane splits. Source: FTDI FT232H datasheet layout guidelines.
Decouple VCC (pin 2) and VCCIO (pins 3, 40) with 100 nF X7R ceramic capacitors placed within 2 mm of each pin, plus a single 10 uF bulk capacitor near the VBUS pin. The VPLL pin (4) requires its own 100 nF + 4.7 uF filter network (per FTDI reference design). Estimated: total bulk decoupling budget for a clean USB-2.0 enumeration is approximately 25 uF distributed across VCC, VCCIO, and VPLL.
Do not omit the external 12 MHz crystal on XI/XO (pins 6/7); the FT232HL cannot operate without a stable reference for its internal 480 MHz PLL. Use a crystal with 18-22 pF load capacitance and place within 5 mm of the IC. Common pitfall: leaving EECS (pin 11) floating when no EEPROM is used - this should be tied to GND so the FT232HL falls back to its internal default VID/PID rather than enumerating as an unknown device.
When driving an external target through MPSSE, place a 22-ohm series resistor on each AD0-AD7 and AC0-AC7 line if the cable to the target exceeds 50 mm. This damps ringing on the SPI/I2C edges and prevents double-clocking on long cables. Estimated: the MPSSE clock runs at up to 30 MHz, so a 50 mm unterminated trace presents roughly 5 nH of inductance which can cause >1 V overshoot on a 3.3 V edge.
اطلاعات انطباق
Lead-free 48-LQFP package per FTDI product page. RoHS compliant. Not AEC-Q100 qualified; the FT232HL is intended for commercial/industrial USB bridge applications, not automotive.
